SEARCH · Engineering Papers

Results for “Vacuum resistivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Thermal analysis of RHIC arc dipole magnet cold mass with EIC beam screen

The existing RHIC storage rings – including their superconducting magnet arcs – will be used for the hadron storage ring of the Electron-Ion Collider (EIC). The vacuum chamber of these magnets was not designed for the EIC hadron beams, with shorter bunches and of higher average current than the RHIC beams. With the current stainless steel beam pipe, the resistive-wall (RW) heating will exceed the dynamic heat load budget. Limiting the RW heating is important to prevent the superconducting magnets from quenching and to maintain a low screen temperature necessary to impede the rise of RW heating (higher resistance at higher temperature) as well as to achieve desired ultra-high vacuum. In addition, simulations predict the formation of electron cloud which would further contribute to the dynamic heat load and could compromise the quality and stability of the beam. To reduce the resistive-wall heating and suppress electron cloud, a beam screen will be installed in the vacuum chamber of the RHIC SC magnets. The screen will have a high RRR copper layer at its inner face – useful to reduce the resistive-wall impedance thanks to its high conductivity especially at cryogenic temperatures – and will be coated with a thin layer of amorphous carbon, a material with low secondary electron yield to suppress the formation of electron clouds. The baseline solution envisages a screen that will be cooled by thermal contact to the 4.55 K beam pipe. Detailed thermal analysis have been conducted in ANSYS 2020 for an arc dipole cold mass equipped with a beam screen in order to study the feasibility of a passively-cooled screen and guide its design. Temperature-dependent thermal conductivity properties of all materials in the operating (cryogenic) temperature range are considered. Suitable assumptions and simplifications are made to model the magnet coil and calculate its homogenized thermal conductivity. Sensitivity studies with respect to layer thicknesses and area of contact are carried out and results are presented.

43 PARTICLE ACCELERATORS↗

DOE OSTI2022

Formation of Al 3 Sc in Al 0.8 Sc 0.2 thin films

We report the formation of Al 3 Sc, in 100 nm Al 0.8 Sc 0.2 films, is found to be driven by exposure to high temperature through higher deposition temperature or annealing. High film resistivity was observed in films with lower deposition temperature that exhibited a lack of crystallinity, which is anticipated to cause more electron scattering. An increase in deposition temperature allows for the nucleation and growth of crystalline Al 3 Sc regions that were verified by electron diffraction. The increase in crystallinity reduces electron scattering, which results in lower film resistivity. Annealing Al 0.8 Sc 0.2 films at 600 °C in an Ar vacuum environment also allows for the formation and recrystallization of Al 3 Sc and Al and yields saturated resistivity values between 9.58 and 10.5 μΩ-cm regardless of sputter conditions. Al 3 Sc was found to nucleate and grow in a random orientation when deposited on SiO 2 , and highly {111} textured when deposited on 100 nm Ti and AlN films that were used as template layers. The rocking curve of the Al 3 Sc 111 reflection for the as-deposited films on Ti and AlN at 450 °C was 1.79° and 1.68°, respectively. Annealing the film deposited on the AlN template reduced the rocking curve substantially to 1.01° due to recrystallization of Al 3 Sc and Al within the film.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Simulating a pulsed-power-driven plasma with ideal MHD

We describe a simple practical numerical method for simulating plasma driven within a vacuum chamber by a pulsed power generator. Typically, in this type of simulation, the vacuum region adjacent to the plasma is approximated as a highly resistive, light fluid; this involves computationally expensive solvers describing the diffusion of the magnetic field through this fluid. Instead, we provide a recipe for coupling pulsed power generators to the magnetohydrodynamics (MHD) domain by approximating the perfectly insulating vacuum as a light, perfectly conducting, inviscid MHD fluid and discuss the applicability of this counter-intuitive technique. This much more affordable ideal MHD representation is particularly useful in situations where a plasma exhibits interesting three-dimensional phenomena, either due to the design of the experiment or due to developing instabilities. We verified that this coupling recipe works by modeling an exactly solvable flux compression generator as well as a self-similar Noh-like solution and demonstrated convergence to the theoretical solution. We also showed examples of simulating complex three-dimensional pulsed power devices with this technique. We release our code implementation to the public.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2020

Fast-current-heating devices to study in situ phase formation in metallic glasses by using high-energy synchrotron radiation

Details of fast-resistive-heating setups, controlled heating ranging from ~10 1 K s –1 to ~10 3 K s –1 , to study in situ phase transformations (on heating and on cooling) in metallic glasses by high-energy synchrotron x-ray diffraction are discussed here. Both setups were designed and custom built at the Leibniz Institute for Solid State and Materials Research Dresden (IFW Dresden) and have been implemented at the P02.1 Powder Diffraction and Total Scattering Beamline and the P21.1 Swedish Materials Science Beamline at PETRA III storage ring, DESY, Hamburg. The devices are interchangeable at both beamlines. Joule heating is triggered automatically and is timed with the incident beam and detector. The crystallization process can be controlled via a feedback circuit by monitoring the change in the time-dependent resistivity and temperature of glasses. Different ambient atmospheres, such as vacuum and inert gases (He and Ar), can be used to control oxidation and cooling. The main focus of these devices is on understanding the crystallization mechanism and kinetics in metallic glasses, which are brittle and for which fast heating gives defined glass–crystal composites with enhanced plasticity. As an example, phase-transformation sequence(s) in a prototyped Cu–Zr-based metallic glass is described on heating, and a crystalline phase beneficial to the plasticity is identified.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Kinetic equilibrium reconstructions of plasmas in the MAST database and preparation for reconstruction of the first plasmas in MAST upgrade

Reconstructions of plasma equilibria using magnetic sensors were routine during operation of the Mega Ampere Spherical Tokamak (MAST) device, but reconstructions using kinetic profiles were not. These are necessary for stability and disruption analysis of the MAST database, as well as for operation in the upgrade to the device, MAST-U. The three-dimensional (3D) code VALEN is used to determine eddy currents in the 3D vessel structures for vacuum coil test shots, which are then mapped to effective resistances in the two-dimensional vessel groupings in the EFIT equilibrium reconstruction code to be used in conjunction with nearby loop voltage measurements for estimated currents in the structures during reconstruction. Kinetic equilibrium reconstructions with EFIT, using all available magnetic sensors as well as Thomson scattering measurements of electron temperature and density, charge exchange recombination spectroscopy measurements of ion temperature, and internal magnetic field pitch angle measurements from a motional Stark effect (MSE) diagnostic are performed for a large database of MAST discharges. Excellent convergence errors are obtained for the portions of the discharges where the stored energy was not too low, and it is found that reconstructions performed with temperature and density measurements but without MSE data usually already match the pitch angle measurements well. A database of 275 kinetic equilibria is used to test the ideal MHD stability calculation capability for MAST. In conclusion, the necessary changes to conducting structure in VALEN, and diagnostic setup in EFIT have been completed for the upgrade from MAST to MAST-U, enabling kinetic reconstructions to commence from the first plasma discharges of the upgraded device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Design of passive and structural conductors for tokamaks using thin-wall eddy current modeling

Abstract A new three-dimensional electromagnetic modeling tool ( ThinCurr ) has been developed using the existing PSI-Tet finite-element code in support of conducting structure design work for both the SPARC and DIII-D tokamaks. Within this framework a 3D conducting structure model was created for both the SPARC and DIII-D tokamaks in the thin-wall limit. This model includes accurate details of the vacuum vessel and other conducting structural elements with realistic material resistivities. This model was leveraged to support the design of a passive runaway electron mitigation coil (REMC), studying the effect of various design parameters, including coil resistivity, current quench duration, and plasma vertical position, on the effectiveness of the coil. The REMC is a non-axisymmetric coil designed to passively drive large non-axisymmetric fields during the plasma disruption thereby destroying flux surfaces and deconfining RE seed populations. These studies indicate that current designs should apply substantial 3D fields at the plasma surface during future plasma current disruptions as well as highlight the importance of having the REMC conductors away from the machine midplane in order to ensure they are robust to off-normal disruption scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Nanoporous Wood Chips Based Sizable, Robust, and Low-Cost Honeycomb Vacuum Insulation Panels (DOE BENEFIT Final Research Performance Progress Report (RPPR))

Conventional vacuum insulation panels (VIPs) suffer from severe limitations including high cost, vulnerability to perforation, and significant performance degradation over time due to vacuum loss. InventWood Inc. (IW) and partnering teams completely re-engineered the VIP structure by constructing arrays of isolated vacuum-cells to enable limited cutting at designated areas (in between vacuum cells) and reduced consequential vacuum loss due to puncture. The teams also replaced the expensive vacuum insulation core materials with a low-cost commercial wood pulp and recycled long fiber. The wood pulp derived VIP can deliver an overall panel insulation of R15 (<0.01W/m·K) with over 90% thermal resistance retention after cutting (R13.5 overall, R5 along the cut edges). In addition, the vacuum-cell-array design minimizes edge losses, resulting in more durable performance, longer service life (>50 years), and higher R-value per dollar towards a cost target of <$1/ft 2 ·in. It is anticipated that the Nanochip-VIP will attract strong market interest and become an affordable insulation solution for energy efficient buildings and retrofits, leading to significant reductions in energy usage.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Effect of Networking Density on the Patterning Performance of Molecular Layer Deposited Alucone Electron Beam/EUV Resists

One of the main barriers to continued device scaling in the era of extreme ultraviolet (EUV) lithography is the need for improved photoresist chemistries to address challenges such as poor EUV sensitivity, inadequate etch resistance, and pattern collapse. Metal-organic photoresists are a promising class of materials that can address many of these challenges, and among them, resists deposited via hybrid molecular layer deposition (MLD) have attracted interest for their unique advantages in thickness control, chemical homogeneity, and compatibility with vacuum processing. However, despite many successful demonstrations of patterning, little is known about how the molecular design of hybrid MLD resists affects their lithographic performance. In this work, we study the effect of the network structure, a common feature among all hybrid MLD resists, via a series of aluminum alkoxide ("alucone") negative tone resists with varying networking density. Their patterning mechanism is investigated via electron beam lithography (EBL)─a common proxy for EUV─and compared to their EUV-induced reactions studied via flood exposure and in situ characterization. In conclusion, we show that the resist with the least networking density demonstrates the best sensitivity and resolution, with the ability to resolve dense line/space gratings as small as 14 nm half pitch via EBL.

electron beam lithography↗

DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Synthesis and characterization of electron beam irradiation-induced damage in polycrystalline metal thin films

High-energy physics research, industrial sterilizing, and material processing depend extensively on electron beam accelerators. Exit windows are crucial components of such electron accelerator systems, maintaining vacuum integrity inside the machine while providing mechanical strength, thermal stability, and radiation resistance at the beam-target interface. In this study, thin metallic films of Ni, Ti, Cr, and V were explored for use in electron beam exit windows, and their properties were compared with the properties of their bulk counterparts. Simulation results of metal foils predicted Ti to exhibit less beam power dissipation compared to Ni. However, Ni possesses superior mechanical and structural properties compared to Ti. The performance of these films under electron beam irradiation was examined by depositing thin layers of these films on silicon and metallic substrates using magnetron sputtering and exposing them to e-beam irradiation in a controlled setup. The deposited films were subjected to a dose of approximately 66 kGy at a beam energy of 10 MeV and characterized prior to and postexposure to the beam using field emission scanning electron microscopy, atomic force microscopy, x-ray diffraction (XRD), and nanoindentation. Particular emphasis was given to characteristics like the grain structure, surface morphology, dislocation density, and hardness. XRD patterns revealed irradiation-induced changes in peak intensities, while the crystallinity remained largely unchanged. Nanoindentation results showed that the pristine and irradiated Ti and Ni films were twice as hard when compared to bulk Ti and Ni samples, regardless of the substrate type used (Si or bulk Ti, or Ni). These results emphasize the superior mechanical properties of thin metal films compared to their bulk counterparts. In conclusion, this study advances the optimization of thin film materials for robust and efficient e-beam applications, ensuring improved durability and operational reliability.

AFM↗

DOE OSTI2020

Assessment of AFM - KPFM and SSRM for Measuring and Characterizing Materials Aging Processes

Atomic Force Microscopy (AFM), in conjunction with Peak Force Kelvin Probe Force Microscopy (PF-KPFM) and Peak Force Scanning Spreading Resistance Microscopy (PF-SSRM), was used to assess changes on thin metal films that underwent accelerated aging. The AFM technique provides a relatively easy, non-destructive methodology that does not require high-vacuum facilities to obtain nanometer-scale spatial resolution of surface chemistry changes. Surface morphology, roughness, contact potential difference, and spreading resistance were monitored to qualitatively identify effects of aging-morphology changes and oxidation of Au, Al, Cu thin film standards as well as diffusion of CuAu and AlAu thin film stacks at 65C under dried nitrogen flow conditions. AFM PF-KPFM and PF-SSRM modes have been exercised, refined and have proven to be viable and necessary early aging detection tools.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Tensile creep properties of NbTaTi and NbTaTiV refractory complex concentrated alloys

Refractory complex concentrated alloys (RCCAs) have emerged as promising candidates for high-temperature structural applications due to their high melting points and potential for exceptional strength, whereas their creep properties remain relatively underexplored. Here, we investigate the tensile creep behavior of NbTaTi and NbTaTiV in high vacuum to elucidate the influence of alloying on creep mechanisms. NbTaTiV exhibits higher creep resistance than NbTaTi, which is attributed to V-induced edge-dislocation-glide-controlled deformation. Microstructural analysis reveals the formation of Ti- and interstitial impurity-rich secondary phases during creep, which enhances the creep resistance without significant embrittlement. Stress exponents (∼3) and activation energies (∼those for vacancy diffusion) align with thermally activated dislocation glide-controlled creep. Despite NbTaTiV surpassing Ni-based superalloys in yield strength at elevated temperatures, its single-phase BCC structure limits creep resistance under engineering-relevant conditions, highlighting the necessity of deliberate secondary phase design to achieve competitive high-temperature performance.

Complex concentrated alloys↗

DOE OSTI2020

Low- n global ideal MHD instabilities in the CFETR baseline scenario

This article reports an evaluation on the linear ideal magnetohydrodynamic (MHD) stability of the China Fusion Engineering Test Reactor (CFETR) baseline scenario for various first-wall locations. The initial-value code NIMROD and eigen-value code AEGIS are employed in this analysis. Despite the distinctly different approaches in modeling the scrape off layer region, the dominant growth in each of the low-n (n=1–10) modes are consistent between the two codes. We report the higher-n modes are dominated by ballooning modes and localized in the pedestal region, while the lower-n modes have more prominent external kink components and broader mode profiles. The influence of the plasma-vacuum profile and wall shape are also examined using NIMROD. In the presence of a resistive wall, the low-n ideal MHD instabilities are further studied using AEGIS. For the designed first-wall location, the n=1 resistive wall mode is found to be unstable, which could be fully stabilized by uniform toroidal rotation above the 2.9% core Alfven speed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Silver Nanowire-Indium Zinc Oxide Composite Flexible Transparent Conducting Electrodes Made by Spin- coating and Photonic Curing

Realizing high-throughput, low-cost perovskite solar cell (PSC) manufacturing is highly sought-after in photovoltaic (PV) research in recent years. To fully achieve roll-to-roll (R2R) manufacturing of PSCs, it is important to consider the flexible transparent electrode (TE). PET/ITO is a commonly used substrate for making flexible PSCs. When optimizing transparent conducting materials, there is a tradeoff between sheet resistance (Rsh) and optical transparency. Because commercial PET/ITO substrates are made with slow (~1 m/min) vacuum deposition processes, they tend to be expensive. Therefore, it would be advantageous to develop a high-throughput, R2R compatible, solution-deposition approach for fabricating the TE on PET substrates. While various solution-deposition processes, such as blade coating or slot-die coating, can achieve the desired web speed of > 10 m/min, there is still a need to improve the post-deposition annealing step. One promising post-deposition processing technique is intense-pulsed-light processing, also known as photonic curing. Photonic curing delivers short (0.01 – 100 ms) pulses of broadband (200 – 1500 nm) light from a xenon flash lamp to the samples. Any materials in the sample stack that absorb light will convert the impinging light pulse into heat within the sample, which drives changes in the sample (calcination, phase change, crystallization, etc.). Photonic curing has three main advantages over thermal annealing: 1. Faster processing speed (milliseconds or seconds). 2. Compatibility with plastic substrates. 3. Smaller physical footprint and less wasted energy. Since the light pulses are on for a short time, the intensity can be high while the total energy delivered to the sample is low, minimizing damages to the plastic substrates. In this work, a hybrid TE material is fabricated on PET substrates using photonic curing. The hybrid TE material contains a layer of silver nanowires (AgNWs) and a layer of metal-oxide (InOx, ITO, IZO, etc.). The AgNWs increase the light absorbed by the film during the photonic curing process, which leads to higher processing temperatures, possibly improving the conversion of the metal-oxide layer. The AgNWs also enhance the electrical conductivity of the final TE layer after photonic curing. A AgNW and metal-oxide bilayer is formed by spin coating each solution onto the PET substrate sequentially followed by a single photonic curing process. We use average optical transmittance (Tavg) from 400 to 700 nm and average Rsh to evaluate the TE performance. The following photonic curing parameters are varied to optimize Tavg (maximize) and Rsh (minimize): Pulse voltage, pulse envelope, number of micro-pulses, duty cycle, number of pulses, and pulse repetition rate. Preliminarily, we also observe a significant impact on the TE properties by the volume of AgNW deposited during the spin coating deposition step. Using dispense volumes of 80 µL and 20 µL, we achieve samples with Tavg = 73%, Rsh = 19 Ω/sq, and roughness = 9 nm, and Tavg = 83%, Rsh = 58 Ω/sq, and roughness = 5.6 nm, respectively, after photonic curing.

14 SOLAR ENERGY↗

DOE OSTI2023

Topographic Evolution of Heat-Treated Nb Upon Electropolishing for SRF Applications

Surface finish plays an essential role in the performance of superconducting radio frequency cavities. Several surface treatments have been developed to reduce surface resistance at a moderate accelerating gradient. We investigated the effects of sequential electropolishing on samples vacuum heat-treated at 300 and 600 °C and N-doped Nb samples using atomic force microscopy. The N-doping process precipitates niobium nitrides within grains and, most notably, continuously and deeply along some grain boundaries. Upon electropolishing, the nitrides are preferentially removed leaving behind a topographically imperfect surface marked by relatively deep holes and grooves with low radius of curvature edges. The progression of magnetic field enhancement and superheating field suppression factors upon electropolishing were investigated using atomic force micrographs. While minor changes in magnetic field enhancement and superheating field suppression factors are observed for the 300 and 600 °C heat-treated Nb, substantial improvements are observed for N-doped Nb. In this system, the most severe topographic defects are the grain boundary grooves which substantially suppress the superheating field. We find that the severity of topographic defects is related to the N-doping process.

Lechner, Eric↗

DOE OSTI2023

Variation of γ′ Formers and Refractory Elements for Enhanced Creep resistance and Phase Stability of HAYNES® 282® Alloy

Modifications to the chemistry of alloy 282 were performed to improve the alloy’s resistance to long term creep deformation as well as phase stability. Alloys were prepared using vacuum induction melting, computationally optimized homogenization heat treatment and hot working. Phase stability studies were carried out for up to 5,000 hours at 800°C and 900°C while creep testing was performed at conditions leading to lives past 7,000 hours for temperatures ranging from 740°C to 900°C. The formation of σ and μ phases were reduced in the modified alloy. Atom probe tomography (APT) was performed on the specimens from the phase stability study to investigate changes in the elemental partitioning to the γ and γ′ phases. Post deformation microstructures were analyzed using EBSD and TEM to study the influence of the detrimental phases on damage accumulation during creep.

Detrois, Martin↗

DOE OSTI2021

Thermal quench in ITER locked mode disruptions

Simulations and theory are presented of an ITER locked mode thermal quench(TQ). In present experiments, locked mode disruptions have a long precursor phase,followed by a rapid termination and thermal quench, which can be identified with a resistive wall tearing mode (RWTM). In ITER, the RWTM will be slowed by the highly conductive vacuum vessel. Here, the rapid termination might be absent, and the plasma could remain in the precursor phase. If the edge temperature is in the collisional regime, the TQ would proceed on a long timescale, limited by the RWTM to almost100ms. This is an important self mitigating effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Beam Induced Heating Analysis Update for the EIC Vacuum Chamber Components

One of the challenges of designing the Electron-Ion Col lider (EIC) is to mitigate beam-induced heating due to the intense electron and hadron beams. Heating of the ESR vac uum chamber components is mainly due to beam-induced resistive wall (RW) losses and synchrotron radiation. For the HSR heating is mainly due to large radial offsets and heat conduction from room temperature to cryogenic tem perature for cryo-components. In this paper, we provide an update on the beam-induced heating and thermal analysis of some critical ESR vacuum chamber components, such as the ESR Large Angle Bremhustraulung Monitor (LABM). We also provide a similar update for critical HSR vacuum com ponents, including the cryo-cooled BPM button assembly, beam screen, abort kicker, and polarimeter. To perform the thermal analyses, the resistive wall loss on individual compo nents is calculated with CST and the synchrotron radiation (if exists) is evaluated using SynRad. These losses, along with realistic boundary conditions are then fed to ANSYS to determine the temperature distribution.

43 PARTICLE ACCELERATORS↗