Results for “Thermoplastic composites” — Page 2

NASA NTRSDate not supplied

Thermal Modelling of the in-Situ Consolidation of Automated Fiber Placement of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Thermoplastics↗

DOE OSTI2022

Understanding the Elastic, Plastic, and Damage Features in Fracturing of Self-reinforced Thermoplastic Composites via Non-destructive Digital Imaging Correlation

This work demonstrated the utilization of non-destructive Digital Imaging Correlation (DIC) method to characterize the elastic, plastic, and damage features during the Mode I intra-laminar fracturing process of self-reinforced thermoplastic composites by using a self-reinforced polypropylene (PP) composite as an example. The DIC results clearly showed the development of huge plastic zone (PZ) and non-negligible Fracture Process Zone (FPZ) in front of the notch tip during the fracturing process, and the geometries and sizes of the foregoing zones at the peak load were further quantified. Such an interesting fracturing behavior of self-reinforced thermoplastic composites is way different from brittle materials (e.g., glass, acrylic, etc.), ductile materials (e.g., aluminum, steel, etc.), and even quasi-brittle materials (e.g., concrete, nanoparticle-reinforced composites, tough ceramics, wood, cement, carbon/glass fiber-reinforced polymers, etc.). Thus, understanding the elastic, plastic, and damage features is the first step before better characterizing the material fracture properties of self-reinforced thermoplastic composites through new analytical methods and computational modeling. These efforts are of utmost importance for wide applications of self-reinforced thermoplastic composites in various engineering fields in the future.

Lightweight Composites, Self-reinforced Thermoplas↗

NASA NTRSDate not supplied

Simulating High Energy Dynamic Impact of IM7/PEKK Continuous Fiber Laminated Thermoplastic Composite using Open Hole Coupon Experiments

The use of advanced thermoplastic composites (TPC) for structural applications in the aerospace and automotive industries has grown increasingly popular due to their high performance, high manufactured part output, and sustainability. Enhancing verification simulations of the progressive failure in TPCs at the coupon scale is needed to better validate advanced composite material models at larger length scales, such as element level panels. MAT_213, a tabulated composite material model, has been applied to simulate high velocity dynamic impact (HEDI) and is integrated in the LS-DYNA explicit finite element (FE) software. Previous efforts using MAT_213 have calibrated HEDI simulated failures with experimental data. Traditionally simulations have relied on a structured mesh to represent quasi-isotropic panels. For this study, a continuous fiber unidirectional tape, IM7/PEKK, was analyzed through a series of verification studies of notched laminate coupons, then validation analyses of quasi-isotropic panels under HEDI were compared with experimental data. Experiments using unidirectional TPC were performed to obtain tabulated stress vs strain curves using Digital Image Correlation (DIC) for input into MAT_213. Next, notched coupon experiments were used as an intermediate step to calibrate the damage and failure behavior in MAT_213. Lastly, investigations into differences between HEDI simulations using a fiber aligned mesh were compared with experimental failure patterns and damage sizes. The use of experimentally generated material behavior along with selective mesh layout improved HEDI predictions with minimal material parameter calibration.

Polymer matrix composites↗

DOE OSTI2020

Energy Efficient Thermoplastic Composite Manufacturing

The objective of the project was to establish an effective and affordable method to lay-up and consolidate/join large thermoplastic composite aerospace structure with cycle times measured in minutes rather than hours. Composite airplane designs have proven efficient and effective however future potential product production rates are challenging what the current systems can efficiently produce due to material lay-down constraints and extended thermal cycle times. The ability to lay-up then rapidly heat, consolidate, and cool large complex composite structures plus very accurately tool them (i.e. matching CTE of composite materials) along with very precise thermal control is a difficult challenge. Current systems such as autoclave processing of thermoset materials require long cycle times due to method of heating and the large associated thermal masses. These extended cycle times inhibit the ability to meet higher rate production scenarios due to the need for multiple sets of equipment and tools. Thermoplastic composite materials were used to facilitate more rapid cycle times via the elimination of a need for a cure dwell at temperature. Also, utilized induction heating along with smart susceptors to enable the quick cycle times needed while providing precise intrinsic thermal control. The intrinsic control of the induction heating process via the smart susceptors along with the use of laser assisted fiber placement were the key innovations areas developed. The ability to rapidly heat and then precisely control the temperature of the consolidation component was paramount to the success of this project. It is this unique processing attribute coupled with the thermoplastic material characteristics along with rapid lay-up methods that are novel and advantageous. While many requirements and influencing factors decide the materials and processes utilized for future airplane construction, the forecast of accelerated production rates and the recent performance successes of composites in airplane construction provide an opportunity for this processing technology to have significant influence. During the course of this project a number of key accomplishments were completed. They are as follows: The needed laser assisted fiber placement capabilities have been developed and validated on a component of meaningful scale and complexity. Subsequently, a thermoplastic preform of the part scale-up part design was laser assisted fiber placed and made availalbe for consolidation. An induction consolidation system was sized, designed, and fabricated resulting in the full capability to consolidate the scale-up component. The tool for induction consolidating of the scale-up component was designed and fabricated. An aluminum pressure bladder was welded and formed for use as the pressurization membrane to perform the needed application of pressure on the part at temperature to achieve consolidation. The induction consolidation system consisting of the restraint, induction power supply, induction tool with integrated induction coils and smart susceptor liners, along with the aluminum bladder were successfully used to consolidate a large thermoplastic skin. The capability of accomplishing rapid heat-up rates and cool down rates for consolidation of large thermoplastic skins with precise thermal control and even pressure application at the consolidation temperature was validated. The general conclusion is that the use of induction consolidation with smart susceptors is an effective method to rapidly and efficiently consolidate large thermoplastic composite components and enable affordable high rate manufacturing of composites. More specific conclusions generated by this project are as follows: A restraint type induction consolidation system provides an affordable option over the standard press when using the induction consolidation processing method. Aluminum bladders can be formed to the complex shapes needed and supply uniform pressure for consolidation and co-consolidation of thermoplastic composite materials. Straightforward modifications can be made to existing fiber placement robotic systems to enable their use for thermoplastic lay-up applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1991

Characterization of elastic-viscoplastic properties of an AS4/PEEK thermoplastic composite

The elastic-viscoplastic properties of an AS4/PEEK (APC-2) thermoplastic composite were characterized at 24 C (75 F) and 121 C (250 F) by using a one-parameter viscoplasticity model. To determine the strain-rate effects, uniaxial tension tests were performed on unidirectional off-axis coupon specimens with different monotonic strain rates. A modified Bodner and Partom's model was also used to describe the viscoplasticity of the thermoplastic composite. The experimental results showed that viscoplastic behavior can be characterized quite well using the one-parameter overstress viscoplasticity model.

Yoon, K. J.↗

NASA NTRS1989

Pultrusion process development of a graphite reinforced polyetherimide thermoplastic composite

High performance thermoplastic polymers do not contain reactants and solvents able to react with a pultrusion die to yield polymerization; consolidation is therefore performed with a rigid or a boardy prepreg, and consolidation must occur with polymers whose viscosities are of the order of 1 million centipoises or more. Die temperatures are typically above 400 C, by comparison with the 150-200 C encountered in thermosets. A methodical approach is presented here for the development of a pultrusion process suitable for polyetherimide and other engineering thermoplastics, employing SEM, DSC, TGA, and ultrasonic C-scanning.

Wilson, Maywood L.↗

NASA NTRSDate not supplied

Thermoplastic Composite Aircraft Manufacturing Model

A manufacturing process to produce 80 single aisle sized thermoplastic composite aircraft a month is presented. Within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) program a baseline aircraft fuselage was designed and modeled based on the Boeing 787 one-piece barrel build, but scaled down to a single aisle aircraft. Key Performance Parameters (KPPs) of recurring cost, non-recurring cost, and weight are calculated from the model. The outcome of this simulation indicated a prohibitively high non-recurring cost, so the thermoplastic team modeled the manufacturing flow for a panelized fuselage concept. The minimum success criteria is a 30% cost reduction and less than two percent increase in weight compared to the baseline aircraft. Automated Fiber Placement (AFP) is used to layup skins, stamp forming is used to make body frames, stringers, and passenger door surround parts. In the model, Co-Fusion was used to consolidate the skin while simultaneously welding on stringers to make stiffened panels. Additional welding technologies were considered to minimize fastener use and a vertical build concept was used for final assembly to reduce factory size. This manufacturing concept for a thermoplastic aircraft indicated a 39% cost and 12% weight savings compared to the baseline. Additional trade studies were conducted using Northrop Grumman’s Automated Stiffener Forming technology to make stringers and stamp forming instead of AFP to make skins.

thermoplastic composites↗

NASA NTRSDate not supplied

Thermal Modelling of the In-Situ Consolidation of Automated Fiber Placement Of Thermoplastic Composites

NASA is developing carbon fiber reinforced thermoplastic composites processing methods under the Hi-rate Composites Aircraft Manufacturing (HiCAM) project. The in-situ consolidation automated fiber placement (AFP) of thermoplastics (ICAT) process has high potential to increase manufacturing throughput and lower costs as it combines the repeatability and fast lay down rates of AFP with the thermoformability of thermoplastic materials to achieve part consolidation out of the autoclave. Physics-based process models are employed in the ICAT process development to understand, fundamentally, the thermal response of the carbon fiber (CF)/polyaryletherketone (PAEK) material during the rapid heating and cooling associated with laser-assisted AFP. A one-dimensional (1-D) closed-form model was developed capable of predicting the temperature profile through-the-thickness of the tape material. In addition, a two-dimensional (2-D) model was developed to predict the heat transfer through-the-thickness and in the laydown x-direction of the AFP head motion. The solution of the Fourier heat-transfer equations in the 2-D model is approximated using the explicit finite difference numerical method. The temperature profile during placement of PAEK slit-tape materials at various laser target temperatures and placement speeds were measured during ICAT process development trials at Electroimpact®, Inc. †† and the resulting experimental data is compared with the predictions of the 1-D and 2-D models.

Christopher J. Stelter↗

NASA NTRSDate not supplied

Finite Element Thermal Model for Ultrasonic Welding of Thermoplastic Composites

Ultrasonic welding, UW, is a fast and energy-efficient technique for joining thermoplastic composites. It involves the use of high-frequency mechanical vibrations and a static welding force to melt and join adherends. Ultrasonic welding is an enabling technology to reduce the cost and complexity of in-space construction because lightweight thermoplastic composite components can be packaged compactly for launch and then efficiently assembled using supervised autonomous robotic technologies on site. However, the temperatures in space present challenges to UW, and it is critical that the efficacy of process parameters selected for manufacturing in space is understood prior to launch. To this end, a three-dimensional finite element model is presented in this technical presentation. The model incorporates equations for effects of viscoelastic heating and heat transfer on the welding process. The proposed model is applied to predict the temperature distribution in single lap shear, SLS, samples composed of AS4/PEEK (TC1200) composite that were welded using a terrestrial machine as part of a comprehensive weldability study. Thermocouple and infrared spot sensor data from the SLS samples provide empirical temperature measurements for calibration and validation of the UW thermal model. Calibration and validation of the model is an important step given the significant uncertainties in material properties such as the loss modulus and necessary assumptions in the physics implementations which allow the model to converge in an acceptable amount of time. The validated thermal model can be used to simulate the process for the space environment. Future validation sample testing is planned in a vacuum chamber. The result will be a model capable of guiding process parameter selection to ensure acceptable weld bonds when manufacturing in space.

Josh Fody↗

NASA NTRS1998

Accelerated Strength Testing of Thermoplastic Composites

Constant ramp strength tests on unidirectional thermoplastic composite specimens oriented in the 90 deg. direction were conducted at constant temperatures ranging from 149 C to 232 C. Ramp rates spanning 5 orders of magnitude were tested so that failures occurred in the range from 0.5 sec. to 24 hrs. (0.5 to 100,000 MPa/sec). Below 204 C, time-temperature superposition held allowing strength at longer times to be estimated from strength tests at shorter times but higher temperatures. The data indicated that a 50% drop in strength might be expected for this material when the test time is increased by 9 orders of magnitude. The shift factors derived from compliance data applied well to the strength results. To explain the link between compliance and strength, a viscoelastic fracture model was investigated. The model, which used compliance as input, was found to fit the strength data only if the critical fracture energy was allowed to vary with temperature reduced stress rate. This variation in the critical parameter severely limits its use in developing a robust time-dependent strength model. The significance of this research is therefore seen as providing both the indication that a more versatile acceleration method for strength can be developed and the evidence that such a method is needed.

Reeder, J. R.↗

DOE OSTI2021

Validation of a lightning protection system for a fusion-welded thermoplastic composite wind turbine blade tip

Fusion welding for thermoplastic composite wind turbine blades is being investigated as a replacement for adhesives in bond lines to reduce manufacturing time and cost and to promote ease of recyclability. Resistance welding uses an electrically conductive material, such as carbon fiber, embedded in the bond line to heat the joining surfaces and fuse them together under pressure. One main challenge with fusion joining for large wind blades is the ability to use this conductive heating element in the bond line while still protecting the blade from the catastrophic effects of a lightning strike. This paper outlines the design and manufacturing of a lightning protection system for a 5-m-long thermally welded blade tip. The outcomes of high voltage and high current lightning testing applied to the 5 m blade tip show that the proposed design was able to protect the fusion welded bond lines from significant lightning damage.

17 WIND ENERGY↗

NASA NTRSDate not supplied

Balancing Manufacturability with Performance: Achieving Extrudable, High Thermal Conductivity, and Dielectrically Robust Thermoplastic Composites

Improved thermal management solutions for electrical insulation systems are a priority for increasing efficiency. Although polymeric electrical insulation is ubiquitous, it generally exhibits low thermal conductivities (κ ; 0.1 – 0.3 W/mK). High κ electrical insulation systems are desirable for several reasons including improved heat wicking. Polymer-ceramic composites offer a viable path towards increasing κ of electrical insulation systems. However, processing-induced anisotropic particle orientation can result in prohibitively high concentrations of high κ particles being required to achieve impactful improvements. This work evaluates the effectiveness of a double percolation approach and its impacts on extruded polymer composite insulation κ using polyimide (PI), polyphenylsulfone (PPSU), and hexagonal boron nitride (hBN). Thermoplastic composite blends of PI/PPSU exhibited a 15% improvement in composite κ at comparable loading levels of hBN relative to mono-polymer material systems. On the other hand, PI/PPSU/hBN composites exhibited lower dielectric strengths than either neat polymer/hBN composite. A trade-off between maximizing material κ and resultant processing and dielectric performances may exist when using a double percolation approach for thermoplastic composites.

Witold K. Fuchs↗

NASA NTRS1992

Development of thermoplastic composite aircraft structures

Efforts focused on the use of thermoplastic composite materials in the development of structural details associated with an advanced fighter fuselage section with applicability to transport design. In support of these designs, mechanics developments were conducted in two areas. First, a dissipative strain energy approach to material characterization and failure prediction, developed at the Naval Research Laboratory, was evaluated as a design/analysis tool. Second, a finite element formulation for thick composites was developed and incorporated into a lug analysis method which incorporates pin bending effects. Manufacturing concepts were developed for an upper fuel cell cover. A detailed trade study produced two promising concepts: fiber placement and single-step diaphragm forming. Based on the innovative design/manufacturing concepts for the fuselage section primary structure, elements were designed, fabricated, and structurally tested. These elements focused on key issues such as thick composite lugs and low cost forming of fastenerless, stiffener/moldine concepts. Manufacturing techniques included autoclave consolidation, single diaphragm consolidation (SDCC) and roll-forming.

Renieri, Michael P.↗

NASA NTRSDate not supplied

Evaluating Crystallinity in Thermoplastic composites

Polymer matrix composites (PMCs) offer many benefits for the aerospace industry due to their potential for weight reduction when compared to metal or ceramic based materials. Most PMCs currently in flight use thermoset matrices, however, thermoplastic resins are being explored as alternatives due to their ability to be remelted, which is of particular interest due to the potential for in-situ repair and manufacturing required in space. Most thermoplastic resins are semicrystalline polymers. The properties of semicrystalline thermoplastics are largely influenced by their crystallinity, which can vary due to many factors including thermal treatments, environmental conditions, and mechanical deformation. Monitoring the crystallinity of thermoplastic composites is key to ensuring these materials reliably meet the high demands required by space exploration. This talk discusses the use of multiple techniques such as Polarized Light Optical Microscopy and Fourier-Transform Infrared Spectroscopy to characterize the crystallinity in various thermoplastic composites, including carbon fiber reinforced PMCs and novel bio-based Martian and Lunar regolith composites designed for in-situ manufacturing. This work aims to provide the fundamental data necessary to understand the effects of crystallinity on thermoplastic PMCs, which is key to advancing their use in space applications.

Thermoplastics↗

NASA NTRSDate not supplied

Interlaminar R-Curve Effects in Thermoplastic Composites: Experiments and Model Correlations

The interlaminar fracture behavior of thermoplastic composites under Mode-I and Mode-II static loading is investigated in this research. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK)†. Characterization experiments were conducted to measure the load-displacement response, peak load, and propagation of delamination from a pre-implanted Kapton® insert. The Mode-I response was characterized using a double cantilever beam (DCB) test according to the ASTM D5528-22 standard. It was observed that the propagation exhibited significant resistance to delamination growth, i.e., an R-Curve effect. The test data indicated that the steady-state fracture toughness, G SS I , was approximately twice the mean initiation fracture toughness, G Ic . The Mode-II response of an end notch flexure (ENF) specimen tested according to the ASTM D7905-19 standard exhibited an unexpected stable behavior upon attaining peak load. Prior to attaining peak load, the Mode-II response exhibited some non-linearity, which may be attributed to nonlinear bulk material response, e.g., hyper-elasticity, viscoelasticity, plasticity, etc., and potentially friction at the load/support rollers and R-Curve effects. Finite element models based on the Cohesive Zone Method (CZM) and the Virtual Crack Closure Technique (VCCT) were used to predict the DCB and ENF specimen responses. DCB analysis results obtained using G SS I predicted propagation consistent with experimental data. However, results obtained with the as characterized G Ic were inaccurate in predicting delamination growth onset and peak load. ENF analysis results obtained with the as-characterized Mode-II fracture toughness, G IIc , were inaccurate in predicting the peak load and propagation. Hence, R-Curve effects were included in both DCB and ENF simulations, which enabled improved predictions. The experimentally determined Mode-I R-Curve was used for the DCB simulations, whereas an R-Curve was derived for Mode-II assuming that the change in compliance of the specimen was associated with crack growth only.

Prabhakar M Rao↗

NASA NTRSDate not supplied

Interlaminar R-Curve Effects in Thermoplastic Composites: Experiments and Model Correlations

The interlaminar fracture behavior of thermoplastic composites under Mode-I and Mode-II static loading is investigated in this research. The material system under consideration is a carbon fiber reinforced low melt semi-crystalline resin TC1225 LMPAEK T700G (T700/LMPAEK)†. Characterization experiments were conducted to measure the load-displacement response, peak load, and propagation of delamination from a pre-implanted Kapton® insert. The Mode-I response was characterized using a double cantilever beam (DCB) test according to the ASTM D5528-22 standard. It was observed that the propagation exhibited significant resistance to delamination growth, i.e., an R-Curve effect. The test data indicated that the steady-state fracture toughness, G SS I , was approximately twice the mean initiation fracture toughness, G Ic . The Mode-II response of an end notch flexure (ENF) specimen tested according to the ASTM D7905-19 standard exhibited an unexpected stable behavior upon attaining peak load. Prior to attaining peak load, the Mode-II response exhibited some non-linearity, which may be attributed to nonlinear bulk material response, e.g., hyper-elasticity, viscoelasticity, plasticity, etc., and potentially friction at the load/support rollers and R-Curve effects. Finite element models based on the Cohesive Zone Method (CZM) and the Virtual Crack Closure Technique (VCCT) were used to predict the DCB and ENF specimen responses. DCB analysis results obtained using G SS I predicted propagation consistent with experimental data. However, results obtained with the as characterized G Ic were inaccurate in predicting delamination growth onset and peak load. ENF analysis results obtained with the as-characterized Mode-II fracture toughness, G IIc , were inaccurate in predicting the peak load and propagation. Hence, R-Curve effects were included in both DCB and ENF simulations, which enabled improved predictions. The experimentally determined Mode-I R-Curve was used for the DCB simulations, whereas an R-Curve was derived for Mode-II assuming that the change in compliance of the specimen was associated with crack growth only.

Prabhakar Rao↗

DOE OSTI2021

IACMI Project 4.2: Thermoplastic Composite Development for Wind Turbine Blades

(Section 5.1) Composites made from Arkema’s Elium® thermoplastic resin and Johns Manville fiberglass were researched during this project for applications in wind blade manufacturing. A techno-economic model was developed to model this wind blade manufacturing process using these materials in place of traditional composites made with thermoset resin. This model was based on manufacturing a 61.5-meter wind blade, which showed a 4.7% reduction in wind blade cost as compared traditional thermoset materials. These cost savings were not from the thermoplastic material costing less than traditional thermoset materials, but rather from decreased capital costs, faster cycle times and reduced energy requirements and labor costs. (Section 5.2) An infusion and curing model was developed for thermoplastic composite wind blades using PAM-RTM. The primary goal was to demonstrate the infusion simulation for the Elium® resin system on a 13-meter wind blade. Additionally, the exotherm temperature was predicted and compared to measurements, which showed model results within 10% of actual measurements. (Section 5.3) Composite laminate panels and composite sandwich panels with a balsa core were produced; specimens were cut and characterized. Similar composite specimens were made with Elium® thermoplastic resin and Hexion thermoset epoxy (RIMR135/RIMH1366) to enable comparisons between these resin systems. The static test methods included: tensile, compression, in-plane shear, interlaminar shear, flexural, sandwich core shear flexure, and single cantilever beam tests for sandwich beams. Fatigue testing at room temperature was completed to composite laminate panels at a stress ratio of R=0.1 and R=10. In addition, fatigue testing to laminate panels was completed at -30°C, and at room temperature after conditioning specimens at 70°C and 90% relative humidity. Overall, mechanical test results from Elium® composites are similar to epoxy composites. (Section 5.4) Elium composite panels were produced with intentional defects such as voids and nonwetting of fibers to begin to understand performance sensitivity to defects. A thermal digital image correlation (TDIC) method provides high spatial resolution strain field at elevated temperatures and can be used to identify defective regions within composite panels. Flexural modulus differences of 21% were seen between defect and non-defect panels. Other Elium® composite panels were forced to be defective by boiling the resin after infusion, which created voids throughout the composite laminate. X-ray computed tomography scanning was used to view the internal structure of the defect panels. Defect panels had a significant reduction in fatigue life as compared to baseline panels produced without intentional defects. (Section 5.5) Lap shear specimens were fabricated to compare the lap shear strength of an off-the-shelf adhesive (Plexus MA590) and two new adhesives developed by Arkema (Bostik SAF30 90 and Bostik SAF30 120). ISO standard 4587:2003 was used to standardize the testing method and sample fabrication. Lap shear specimens were made at 1mm, 3mm, and 10mm thicknesses. The Bostik adhesive lap shear test results were similar to Plexus for all thicknesses. (Section 5.6) Fiber-reinforced polymer (FRP) composites are typically used in high-performance applications (e.g., aerospace), and their expansion into high-volume industries (e.g. consumer automotive and wind turbine blade manufacturer or similar) is hindered by their cost and a lack of efficient manufacturing techniques. Monitoring the curing process of these composites during manufacturing can improve the efficiency of the process, and therefore reduce the manufacturing cost. Cure monitoring techniques were developed that use probabilistic estimation methods and surface temperature measurements made using infrared cameras. These techniques enable real-time monitoring of the infusion process to locate manufacturing flaws, and they can, potentially, estimate residual stresses in the part. Their commercialization will help facilitate expansion of FRP composites in high-volume industries. (Section 5.7) A 13-meter composite wind blade was produced with Elium® resin and Johns Manville fiberglass; this blade was made with VARTM processing similar to how megawatt-scale wind blades are currently manufactured, but no post-mold heating was used for this thermoplastic composite blade. The wind blade underwent full-scale validation for static loading (4-different load orientations) and flapwise fatigue loading to simulate 20-years of operational loads. The thermoplastic composite wind blade withstood the loading without any noted issues and performed similar to results from a previous full-scale validation to an equivalent epoxy composite wind blade produced with the same blade molds. (Section 5.8) A study was conducted to determine the feasibility of recycling composite wind turbine blade components fabricated with glass fiber reinforced Elium® thermoplastic resin. Dissolution, which is a process unique to thermoplastic matrices, allows recovery of both the polymer matrix and full-length glass fibers, while maintaining their stiffness and strength throughout the recovery process. The economics of recycling is favorable if 50% of the glass fiber is recovered and resold for a process of $\$$ 0.28/kg, and 90% of the resin is recovered and resold at a price of $\$$ 2.50/kg.(Section 10) Recommendations are outlined for commercializing thermoplastic resin for composite wind blade production, in addition to recommended areas for future research.

17 WIND ENERGY↗

NASA NTRS1988

Instability-related delamination growth in thermoset and thermoplastic composites

Mixed-mode crack propagation in compressively loaded thermoset and thermoplastic composite columns with an imbedded through-width delamination is investigated. Beam theory is used to analyze the geometrically nonlinear load-deformation relationship of the delaminated subregion. The elastic restraint model (ERM), combined with existing FSM modeling of the crack-tip region, yields expressions for the Mode I and Mode II components of the strain energy release rate G(I) and G(II) to predict the critical load at the onset of delamination growth. Experimental data were generated for geometries yielding a wide range of G(I)/G(II) ratios at the onset of crack growth. A linear mixed-mode crack growth criterion in conjunctuion with the ERM provides good agreement between predicted and measured critical loads for both materials studied.

Gillespie, John W., Jr.↗