Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Thermo-Calc”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Thermodynamic analysis of binary Fe{sub 85}B{sub 15} to quinary Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloys for primary crystallizations of α-Fe in nanocrystalline soft magnetic alloys

Fe-based Fe{sub 85}B{sub 15}, Fe{sub 84}B{sub 15}Cu{sub 1}, Fe{sub 82}Si{sub 2}B{sub 15}Cu{sub 1}, Fe{sub 85}Si{sub 2}B{sub 12}Cu{sub 1}, and Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} (NANOMET{sup ®}) alloys were experimental and computational analyzed to clarify the features of NANOMET that exhibits high saturation magnetic flux density (B{sub s}) nearly 1.9 T and low core loss than conventional nanocrystalline soft magnetic alloys. The X-ray diffraction analysis for ribbon specimens produced experimentally by melt spinning from melts revealed that the samples were almost formed into an amorphous single phase. Then, the as-quenched samples were analyzed with differential scanning calorimeter (DSC) experimentally for exothermic enthalpies of the primary and secondary crystallizations (ΔH{sub x1} and ΔH{sub x2}) and their crystallization temperatures (T{sub x1} and T{sub x2}), respectively. The ratio ΔH{sub x1}/ΔH{sub x2} measured by DSC experimentally tended to be extremely high for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy, and this tendency was reproduced by the analysis with commercial software, Thermo-Calc, with database for Fe-based alloys, TCFE7 for Gibbs free energy (G) assessments. The calculations exhibit that a volume fraction (V{sub f}) of α-Fe tends to increase from 0.56 for the Fe{sub 85}B{sub 15} to 0.75 for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy. The computational analysis of the alloys for G of α-Fe and amorphous phases (G{sub α-Fe} and G{sub amor}) shows that a relationship G{sub α-Fe} ∼ G{sub amor} holds for the Fe{sub 85}Si{sub 2}B{sub 12}Cu{sub 1}, whereas G{sub α-Fe} < G{sub amor} for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy at T{sub x1} and that an extremely high V{sub f} = 0.75 was achieved for the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy by including 2.8 at. % Si and 4.5 at. % P into α-Fe. These computational results indicate that the Fe{sub 85}Si{sub 2}B{sub 8}P{sub 4}Cu{sub 1} alloy barely forms amorphous phase, which, in turn, leads to high V{sub f} and resultant high B{sub s}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analytical modeling of the evolution of the nonlinearity parameter of sensitized stainless steel

Austenitic stainless steels are subject to the precipitation of chromium carbides (M 23 C 6 ) during exposure to high temperatures, causing these alloys to be susceptible to intergranular corrosion due to chromium depletion along grain boundaries. The acoustic nonlinearity parameter, β, shows sensitivity to the formation of carbides in these alloys. The Thermo-Calc TC-PRISMA module was used to model the nucleation and growth of grain boundary M 23 C 6 carbides. The model was verified with scanning transmission electron microscopy analysis that allowed measurements of the grain boundary precipitates. The paper introduces a reduced-order model of the acoustic nonlinearity based on the formation of misfit dislocations at the interface of the grain boundary precipitate and matrix to explain the change in β during isothermal aging. Furthermore, a direct relationship between the radius of the M 23 C 6 grain boundary carbides and β was observed and verified with nonlinear ultrasound measurements on 304L and 316L stainless steels.

36 MATERIALS SCIENCE↗

First-principles study on structural mechanical and thermodynamic properties of HfMoTaTiZr

This study calculates the phase diagram of HfMoTaTiZr using the TCHEA1 database in Thermo-Calc software. Furthermore, it also investigates the structural and mechanical properties of HfMoTaTiZr by applying first-principles calculations. The elastic and other mechanical properties such as Young’s modulus, pugh ratio, hardness, bulk modulus was derived and discussed. These parameters were found to be in good harmony with previously available experimental reports. Vickers hardness of HfMoTaTiZr predicted from the Tians model agrees with the available experimental result. This study also investigates the thermal coefficient of linear expansion and vibrational heat capacity of the HfMoTaTiZr using the Debye–Grüneisen theory.

36 MATERIALS SCIENCE↗

Equilipy

There is high demand for high-throughput calculations of phase equilibria based on the CALPHAD method (CALculation of PHAse Diagram). High-throughput calculations are possible through HPC, currently by a commercial program called Thermo-Calc. However, the number of nodes/processors are limited to the number of purchased license (16 processors per license). This program provides a toolkit for high-throughput calculations of phase equilibria by the CALPHAD method. The program is prepared for Python environment, so that it can be easily installed and used together with other open-source programs. The program can be run in supercomputer.

Kwon, Sunyong [Oak Ridge National Laboratory (ORNL↗

Design of crack-free laser additive manufactured Inconel 939 alloy driven by computational thermodynamics method

Abstract This paper examined the effect of Si addition on the cracking resistance of Inconel 939 alloy after laser additive manufacturing (AM) process. With the help of CALculation of PHAse Diagrams (CALPHAD) software Thermo-Calc, the amounts of specific elements (C, B, and Zr) in liquid phase during solidification, cracking susceptibility coefficients (CSC) and cracking criterion based on $$\left| {{\text{d}}T/{\text{d}}f_{{\text{s}}}^{1/2} } \right|$$ d T / d f s 1 / 2 values ( T : solidification temperature, f s : mass fraction of solid during solidification) were evaluated as the indicators for composition optimization. It was found that CSC together with $$\left| {{\text{d}}T/{\text{d}}f_{{\text{s}}}^{1/2} } \right|$$ d T / d f s 1 / 2 values provided a better prediction for cracking resistance. Graphical abstract

Zeng, Congyuan (ORCID:0000000214764277)↗

On a Thermodynamic Approach to Material Selection for Service in Aggressive Multi-Component Gaseous and/or Vapor Environments

This report fulfills the M4 milestone, M4FT-15IN08020110 UNF Analysis Support, under Work Package Number FT-15IN080201. The issue of materials selection for many engineering applications represents an important problem, particularly in cases where material failure is possible as a result of corrosive environments. For example, 304 dual purpose or 316 stainless steel is used in the construction of many used nuclear fuel storage canisters. Deployed all over the world, these canisters are housed inside shielded enclosures and cooled passively by convective airflow. When located along seaboards or particular industrial areas, salt, other corrosive chemicals, and moisture can become entrained in the air that cools the canisters. It is important to develop an understanding of what impact, if any, that chemical environment will have on those canisters. In many cases of corrosion in aggressive gaseous environments, the material selection process is based on some general recommendations, anecdotal evidence, and/or the past experience of that particular project’s participants. For gaseous mixtures, the theoretical basis is practically limited to the construction of the so-called “Ellingham diagrams” for pure metals. These plots predict the equilibrium temperature between different individual metals, their respective oxides, and oxygen gas. Similar diagrams can be constructed for the reactions with sulfur, nitrogen, carbon, etc. In the generalization of this approach by Richardson and Jeffes, additional scales can be superimposed upon an Ellingham diagram that would correspond to different gaseous mixtures, e.g. CO/CO 2 , or H 2 /H 2 O. However, while the general approach to predicting the stability of a multi-component heterogeneous alloy (e.g., steel or a superalloy) in a multi-component aggressive gaseous environment was developed in very general form, actual examples of its applications to concrete real-life problems are practically absent. This is related to alloy design, corrosion protection, and material selection for different applications. In this work, an effort was made to advance in that direction using modern computational thermodynamics methodology, software, and databases by Thermo-Calc Inc. The developed methodology is illustrated by the case study – a process of nuclear waste immobilization using a chemical engineering approach described below. The developed methodology can be considered a practical illustration of the Ellingham approach generalization and could be used for obtaining thermodynamic guidance on a given process’ feasibility using equipment/sensors made of a particular multicomponent heterogeneous metallic alloy.

36 MATERIALS SCIENCE↗

Thermodynamic, Kinetic, and Physical Properties of Nb-U (Niobium-Uranium)

Based on an improved coupling between ab initio energetics output, phenomenological thermodynamics based on the CALPHAD (CALculation of Phase Diagrams) approach, and the use of the Thermo-Calc software, together with experimental data (whenever available), a thermodynamic assessment of the Nb-U alloy system was carried out. We made use of the full array of modern electronic-structure techniques based on density functional theory, including ab initio fully relativistic full-potential linear-muffin orbital method (FR-FP-LMTO), methods, the Scalar Relativistic Korringa-Kohn-Rostoker Atomic-Sphere Approximation (SR-KKR-ASA), and the fully relativistic or scalar relativistic Exact muffin-orbital (SR- or FR-EMTO) method, both based on the Green function formalism that has the advantage of being able to treat chemically random configuration (i.e., solid solution) with the so-called coherent potential approximation (CPA). All electronic structure calculations were performed within the Generalized Gradient Approximation (GGA) for the treatment of electron correlations. The results from this technology serve as input for CALPHAD assessment of phase diagrams

36 MATERIALS SCIENCE↗

Durable, Impermeable Brazes for Solid Oxide Fuel Cells (Final Report)

To develop a new braze to replace the current state-of-the-art Ag-CuO reactive air braze (RAB), two approaches were proposed: 1) development of a new, self-passivating, silver-free braze and 2) development of a CuO-free, silver-based braze. For the first approach, an integrated computational-experimental method was used. Thermo-Calc® was utilized to quickly screen through hundreds of alloy systems to identify candidate braze compositions with the appropriate melting ranges. Material compositions, melting ranges, mechanical properties, oxidation resistance, and wetting characteristics of the candidate alloys were then analyzed experimentally. Substrate surface pre-treatments, active element additions, and novel brazing schemes were also investigated. Unfortunately, the current study failed to identify new silver-free braze compositions suitable for SOFC applications. To help measure the passivation characteristics of surface passivating braze oxide coatings, work was conducted to demonstrate, for the first time, that a variety of disparate and technologically-relevant thermal, mechanical, and electrochemical oxygen-exchange thin film material properties could all be obtained from in situ , current-collector-free wafer curvature measurements. Specifically, temperature or oxygen partial pressure induced changes in the curvature of 230 nm thick (100)-oriented Pr 0.1 Ce 0.9 O 1.95_x (10PCO) films atop 200 mm thick single crystal yttria stabilized zirconia or magnesium oxide substrates were used to measure the biaxial modulus, Young’s modulus, thermal expansion coefficient, thermochemical expansion coefficient, oxygen nonstoichiometry, chemical oxygen surface exchange coefficient, oxygen surface exchange resistance, thermal stress, chemical stress, thermal strain, and chemical strain of the model mixed ionic electronic conducting material 10PCO. The (100)-oriented thin film 10PCO thermal expansion coefficient, thermo-chemical expansion coefficient, oxygen nonstoichiometry, and Young’s modulus (which is essentially constant, at ~200 MPa, over the entire 280–700 °C temperature range in air) measured here were similar to those from other bulk and thin film 10PCO studies. In addition, the measured PCO10 oxygen surface coefficients were in agreement with those reported by other in situ , current collector- free techniques. However, the measured PCO10 oxygen surface exchange coefficients were significantly lower than those obtained from literature studies with large amounts of intentional or inadvertent precious metal surface coverage/contamination (suggesting that uncontaminated (100)-oriented 10PCO may not be a desirable SOFC cathode material). Taken together, this highlighted the advantages of using a sample’s mechanical response, instead of the more traditional electrical response, to probe the electrochemical properties of the ion-exchange materials used in solid oxide fuel cell, solid oxide electrolysis cell, gas-sensing, battery, emission control, water splitting, water purification, and other electrochemically-active devices. For the second approach, a novel silver-nickel brazing method was developed. It was demonstrated that transient porous nickel interlayers, instead of reactive element additions, could be used to promote Ag wetting on yttria stabilized zirconia (YSZ) and produce high-quality YSZ stainless steel (SS) braze joints. Mechanical tests on these reactive-element-free, silver-based SOFC braze joints, both before and after 500 hours of 750°C oxidation in air, showed that the braze and braze interface strength were higher than the underlying YSZ|NiO-YSZ substrate. The microstructural and compositional evolution of SS|Ag-Ni|YSZ braze joints exposed to dual atmosphere (air on one side and 4%H 2 -96%N 2 on the other side) for 300 hours of isothermal 750 °C aging and 300 25°C/min 35-830 °C rapid thermal cycles were compared to a Ag-3CuO braze joint. In contrast to conventional Ag-CuO RAB brazes, the Ag-Ni brazes remained pore free and well bonded, suggesting that Ag-Ni brazes may be more suitable for long term SOFC operation than Ag-CuO brazes. Other applications inspired by the silver-nickel wetting process on various ceramic substrates were also explored. In support of efforts to identify new CuO-free Ag-based brazes, density functional theory and ab initio molecular dynamics calculations were performed to 1) understand silver wetting on YSZ, and 2) identify new oxides to promote silver wetting on YSZ. These simulations found that while the formation of dissolved oxygen clusters within molten silver at the YSZ interface promoted wetting, much greater wetting angle reductions came from the formation of metal oxide interlayers at the Ag-YSZ interface. Through the development of a simple descriptor, many simple metal oxides (single cation) were examined. Unfortunately, their ability to promote Ag wetting were less than that of CuO. However, expanding the search to multi-cation oxides led to several promising candidates, such as CuAlO 2 , CuGaO 2 , and Cu 3 TiO 4 ; all of which are also stable in the reducing SOFC conditions. Depending upon their solubility in molten Ag, these newly-identified oxides could either be pre-applied as wetting promoting interlayers or directly incorporated into Ag to form new reactive air brazes.

36 MATERIALS SCIENCE↗

Liquid and Gamma-BCC Phase Equilibria in the Uranium-Niobium System: A Simple Thermodynamic Model for Phase Diagram and Other Predictions

A simple thermodynamic model for the uranium-niobium (U-Nb) system was created using a Calphad-type approach, circa 2002. Only the liquid and gamma-BCC phases were modeled, with their subregular solution mixing terms optimized by trial and error. The custom (user-defined) database file (.tdb) and experimental data file (.exp) are listed, both of which are compatible with Thermo-Calc software. This model is used to calculate the solidus, liquidus, miscibility gap on the U-Nb phase diagram and also the enthalpy of melting in the U-6Nb alloy.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Crack-Free 30% Chromium-Nickel Alloy Welding Products for Nuclear Service

We report prior research in the development of 30% chromium-nickel alloy nuclear welding wires has resulted in the resolution of primary water stress corrosion cracking (PWSCC) and ductility dip cracking (DDC) as well as improvement in solidification cracking (SC) resistance. The resolution of DDC exhibits some Laves phase, which has a negative effect on SC resistance. In this study, the use of an alternate carbide former, tantalum (Ta), in combination with niobium (Nb) was researched. Three heats of recently designed Filler Metal 52MSS-Ta (i.e., HV1648, HV1673A, and VX131WXW) were melted, fabricated, and systematically studied. DDC and SC were evaluated with thermodynamic modeling using the Scheil solidification simulation model, two types of varestraint tests, and strain-to-fracture (STF) testing. The varestraint and STF test results showed an improved SC resistance with reduced Laves phase and concurrent excellent DDC resistance. Optimized compositions with low Laves phase also exhibited high threshold strain values (TSVs) in the STF test. VX131WXW — which contains 2.81 wt-% Ta, 0.6 wt-% Nb, and 6 wt-% iron (Fe) - exhibited a TSV of 24%. Thermo-Calc computed the Laves phase to be 0.24% for VX131WXW compared to 0.06% in HV1673A. This difference in Laves phase resulted in the lower SC resistance of VX131WXW compared to HV1673A when measured with longitudinal varestraint testing. The maximum crack distance for HV1673A was about 0.6 mm while that of heat VX131WXW was about 1.0 mm. The typical diluted weld deposit made with VX131WXW was also resistant to PWSCC due to the chromium content exceeding 24%. These simultaneous results mark progress toward crack-free welds and provide direction for further optimization of Ta-containing filler metals.

30% chromium-nickel alloy↗

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Microstructural changes during thermal processing of a medium manganese steel containing (in wt%) 0.19C and 4.39 Mn were evaluated in situ with a high energy X-ray diffraction system (HEXRD). Samples with an initial fully martensitic microstructure were heated to intercritical annealing (IA) temperatures of 600 or 650°C, held for 30 min, and cooled to room temperature. Diffraction data were analyzed to determine the variations in austenite and ferrite phase fractions and phase lattice constants throughout the ICA cycles. On heating, the 2 vol. pct of austenite present in the starting microstructure decomposed, and cementite precipitation then occurred. During isothermal holding, the austenite fraction increased, up to 20% for the sample annealed at 650°C. The measured austenite fractions were less than those calculated by Thermo-Calc for equilibrium conditions, indicating that the 30-min hold time was insufficient to achieve near-equilibrium conditions. Observed changes in lattice parameters during isothermal holding were interpreted to reflect composition changes due to redistribution of the C and Mn between austenite and ferrite. The results are discussed in relation to the potential for controlling austenite stability during ambient temperature deformation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

LPBF Processability of NiTiHf Alloys: Systematic Modeling and Single-Track Studies

Research into the processability of NiTiHf high-temperature shape memory alloys (HTSMAs) via laser powder bed fusion (LPBF) is limited; nevertheless, these alloys show promise for applications in extreme environments. This study aims to address this limitation by investigating the printability of four NiTiHf alloys with varying Hf content (1, 2, 15, and 20 at. %) to assess their suitability for LPBF applications. Solidification cracking is one of the main limiting factors in LPBF processes, which occurs during the final stage of solidification. To investigate the effect of alloy composition on printability, this study focuses on this defect via a combination of computational modeling and experimental validation. To this end, solidification cracking susceptibility is calculated as Kou’s index and Scheil–Gulliver model, implemented in Thermo-Calc/2022a software. An innovative powder-free experimental method through laser remelting was conducted on bare NiTiHf ingots to validate the parameter impacts of the LPBF process. The result is the processability window with no cracking likelihood under diverse LPBF conditions, including laser power and scan speed. This comprehensive investigation enhances our understanding of the processability challenges and opportunities for NiTiHf HTSMAs in advanced engineering applications.

36 MATERIALS SCIENCE↗

Monolithic Cu-Cr-Nb Alloys for High Temperature, High Heat Flux Applications

Work during the prior four years of this grant has resulted in significant advances in the development of Cu-8 Cr4 Nb and related Cu-Cr-Nb alloys. The alloys are nearing commercial use in the Reusable Launch Vehicle (RLV) where they are candidate materials for the thrust cell liners of the aerospike engines being developed by Rocketdyne. During the fifth and final year of the grant, it is proposed to complete development of the design level database of mechanical and thermophysical properties and transfer it to NASA Glenn Research Center and Rocketdyne. The database development work will be divided into three main areas: Thermophysical Database Augmentation, Mechanical Testing and Metallography and Fractography. In addition to the database development, work will continue that is focussed on the production of alternatives to the powder metallurgy alloys currently used. Exploration of alternative alloys will be aimed at both the development of lower cost materials and higher performance materials. A key element of this effort will be the use of Thermo-Calc software to survey the solubility behavior of a wide range of alloying elements in a copper matrix. The ultimate goals would be to define suitable alloy compositions and processing routes to produce thin sheets of the material at either a lower cost, or, with improved mechanical and thermal properties compared to the current Cu-Cr-Nb powder metallurgy alloys.

Ellis, David L.↗

Effects of Tantalum on the Temporal Evolution of a Model Ni-Al-Cr Superalloy During Phase Decomposition

The effects of a 2.0 at.% addition of Ta to a model Ni-10.0Al-8.5Cr (at.%) superalloy aged at 1073 K are assessed using scanning electron microscopy and atom-probe tomography. The gamma'(Ll2)-precipitate morphology that develops as a result of gamma-(fcc)matrix phase decomposition is found to evolve from a bimodal distribution of spheroidal precipitates, to {001}-faceted cuboids and parallelepipeds aligned along the elastically soft {001}-type directions. The phase compositions and the widths of the gamma'-precipitate/gamma-matrix heterophase interfaces evolve temporally as the Ni-Al-Cr-Ta alloy undergoes quasi-stationary state coarsening after 1 h of aging. Tantalum is observed to partition preferentially to the gamma'-precipitate phase, and suppresses the mobility of Ni in the gamma-matrix sufficiently to cause an accumulation of Ni on the gamma-matrix side of the gamma'/gamma interface. Additionally, computational modeling, employing Thermo-Calc, Dictra and PrecipiCalc, is employed to elucidate the kinetic pathways that lead to phase decomposition in this concentrated Ni-Al-Cr-Ta alloy.

Booth, Morrison, Christopher↗

Investigating Fifth Oxide Effect on CMXAS Glass Properties

Coatings for hot section aero turbine engine structural materials are subject to thermochemical degradation after interacting with calcium-magnesium-aluminosilicates (CMAS). Molten CMAS viscosity is the primary glass property of importance, correlating with coating infiltration and reaction depth. CMAS viscosity was measured using a spindle-dipped viscometer at temperatures between 1300-1550°C in 25°C increments. Experimental data were compared to Thermo-Calc and FactSage computational models, which showed good agreement with experimental trends. CMXAS compositions, where X denotes a fifth oxide, of Ca30.75-Mg9-X5-Al13-Si42.25 (single cation oxide mol%) for X = Fe2+, Fe3+, Gd3+, Hf4+, Na1+, Ti4+, Y3+, Yb3+, Zr4+ additions were used. Oxide precipitation was observed in X = Hf4+ , Zr4+ CMXAS specimens, indicating coating dissolution is an increased threat for T ≥ 1390°C. Molten CMAS and CMXAS viscosity measurements were shown to correlate with net cation field strength, offering an alternative in property prediction where thermodynamic data are unavailable.

Clark Avery Luckhardt↗

ADDITIVE MANUFACTURING OF REFRACTORY ALLOYS

Refractory alloys are known for their high temperature capabilities and are intended for use at ultra-high temperatures above even 1200°C, which exceeds the capabilities of conventional superalloys. Additive manufacturing (AM) is an attractive alternative processing route because refractory alloys are difficult to fabricate through traditional methods; AM can form a near net-shape part with a tailored microstructure. This work seeks to evaluate the solidification behavior of refractory alloys under AM conditions and establish corresponding solidification models. Two binary alloys, Mo30Nb and Nb7.5Ta, as well as the commercial Nb alloy, C103, and one refractory high entropy alloy (RHEA), MoNbTaTi, were subjected to single track melts in a laser powder bed fusion (LPBF) machine. Each melt track was evaluated in the scanning electron microscope (SEM), which determined that some AM conditions used led to non-ideal behavior. Electron backscatter diffraction (EBSD) revealed that the Nb7.5Ta, C103, and MoNbTaTi all exhibited new grain nucleation to various extents while the Mo30Nb exhibited primarily epitaxial growth. This was found to be inconsistent with solidification models that were developed for each alloy and each set of AM conditions to predict the columnar to equiaxed transition behavior (CET) of the experimental microstructures. This disparity was largely attributed to the input parameters for the solidification model, which were developed using Thermo-Calc and SYSWELD. These input parameters include the alloy specific Gibbs-Thomson coefficient and thermophysical properties, the solute specific liquidus slopes and partitioning coefficients, as well as the process specific thermal gradients. Each input parameter was evaluated to determine the likely changes required for the modeled values to generate solidification models that better correspond to what was observed experimentally.

Miklas, Abigail↗

Extending SLUSCHI for Automated Diffusion Calculations

We present an extension of the SLUSCHI package (Solid and Liquid in Ultra Small Coexistence with Hovering Interfaces) to enable automated diffusion calculations from first-principles molecular dynamics. While the original SLUSCHI workflow was designed for melting temperature estimation via solid-liquid coexistence, we adapt its input and output handling to isolate the volume search stage and generate one production trajectory suitable for diffusion analysis. Post-processing tools parse VASP outputs, compute mean-square displacements (MSD), and extract tracer diffusivities using the Einstein relation with robust error estimates through block averaging. Diagnostic plots, including MSD curves, running slopes, and velocity autocorrelations, are produced automatically to help identify diffusive regimes. The method has been validated through representative case studies: self-diffusion in Al-Cu liquid alloys, sublattice melting in Li7La3Zr2O12 and Er2O3, interstitial oxygen transport in bcc and fcc Fe, and oxygen diffusivity in Fe-O liquids with variable Si and Al contents. Viscosity and diffusivity are linked through the Stokes-Einstein relation, with composition dependence assessed via simple linear mixing. This capability broadens SLUSCHI from melting-point predictions to transport property evaluation, enabling high-throughput, fully first-principles datasets of diffusion coefficients and viscosities across metals and oxides.

36 MATERIALS SCIENCE↗

Effect of heat treatment on microstructure and hardness of Grade 91 steel

The modified 9Cr-1Mo steel (Grade 91) is a material of choice in fossil-fuel-fired power plants with increased efficiency, service life, and reduction in emission of greenhouse gases. It is also considered a prospective material for the Next Generation Nuclear Power Plant for application in reactor pressure vessels at temperatures up to 650°C. In this paper, heat treatment of the modified 9Cr-1Mo steel was studied by normalizing and tempering the steel at various temperatures and times, with the ultimate goal of improving its creep resistance and optimizing material hardness. The microstructural evolution of the heat treated steels was correlated with the differential scanning calorimetric results. Optical microscopy, scanning and transmission electron microscopy in conjunction with microhardness profiles and calorimetric plots were used to understand the evolution of microstructure including precipitate structures in modified 9Cr-1Mo steel and relate it to the mechanical behavior of the steel. Thermo-CalcTM calculations were used to support experimental work and provide guidance in terms of the precipitate stability and microstructural evolution. Furthermore, the carbon isopleth and temperature dependencies of the volume fraction of different precipitates were constructed. The predicted and experimentally observed results were found to be in good agreement.

20 FOSSIL-FUELED POWER PLANTS↗