Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Tank testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1934

Complete tank tests of two flying-boat hulls with pointed steps - N.A.C.A. Models 22-A and 35

This note presents the results of complete tank test of N.A.C.A. Models 22-A and 35, two flying-boat hulls of the deep pointed-step type with low dead rise. Model 22-A is a form derived by modification of Model 22, the test results of which are given in N.A.C.A. Technical Note No. 488. Model 35 is a form of the same type but has a higher length-beam ratio than either Model 22 or 22-A. Take-off examples are worked out using data from these tests and a previous test of a conventional model applied to an arbitrary set of design specifications for a 15,000-pound flying boat. The comparison of these examples shows both pointed-step models to be superior to the conventional form, and Model 35 to be the better of the two. Model 35 is applied to a hypothetical 100,000-pound flying boat of the twin-hull type and performance calculations are made both for take-off and range. The results indicate that the high performance of this type of hull will enable the designer to use higher wing and power loadings than are found in current practice, with a resulting increase in range and pay load.

Shoemaker, James M↗
NASA NTRS1933

A complete tank test of a model of a flying-boat hull-N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M↗
NASA NTRS1935

A General Tank Test of NACA Model 11-C Flying-boat Hull, Including the Effect of Changing the Plan Form of the Step

The results of a general tank test model 11-C, a conventional pointed afterbody type of flying-boat hull, are given in tables and curves. These results are compared with the results of tests on model 11-A, from which model 11-C was derived, and it is found that the resistance of model 11-C is somewhat greater. The effect of changing the plan form of the step on model 11-C is shown from the results of tests made with three swallow-tail and three pointed steps formed by altering the original step of the model. These results show only minor differences from the results obtained with the original model.

Dawson, John R↗
NASA NTRS1936

Tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise - NACA model 35 series

The results of tank tests of three models of flying-boat hulls of the pointed-step type with different angles of dead rise are given in charts and are compared with results from tests of more conventional hulls. Increasing the angle of dead rise from 15 to 25 degrees: had little effect on the hump resistance; increased the resistance throughout the planning range; increased the best trim angle; reduced the maximum positive trimming moment required to obtain best trim angle; and had but a slight effect on the spray characteristics. For approximately the same angles of dead rise the resistance of the pointed-step hulls were considerably lower at high speeds than those of the more conventional hulls.

Dawson, John R↗
NASA NTRS2012

STS-133/ET-137 Tanking Test Photogrammetry Assessment

Following the launch scrub of Space Shuttle mission STS-133 on November 5, 2010, an anomalous condition of cracked and raised thermal protection system (TPS) foam was observed on the External Tank (ET). Subsequent dissection of the affected TPS region revealed cracks in the feet of two Intertank (IT) metallic stringers. An extensive investigation into the cause(s) and corrective action(s) for the cracked stringers was initiated, involving a wide array of material and structural tests and nondestructive evaluations, with the intent to culminate into the development of flight rational. One such structural test was the instrumented tanking test performed on December 17, 2010. The tanking test incorporated two three-dimensional optical displacement measurement systems to measure full-field outer surface displacements of the TPS surrounding the affected region that contained the stringer cracks. The results showed that the radial displacement and rotation of the liquid oxygen (LO2) tank flange changed significantly as the fluid level of the LO2 approached and passed the LO2 tank flange.

Oliver, Stanley T.↗
NASA NTRS1938

A general tank test of a model of the hull of the Pem-1 flying boat including a special working chart for the determination of hull performance

The results of a general tank test of a 1/6 full-size model of the hull of the Pem-1 flying boat (N.A.C.A. model 18) are given in non-dimensional form. In addition to the usual curves, the results are presented in a new form that makes it possible to apply them more conveniently than in the forms previously used. The resistance was compared with that of N.A.C.A. models 11-C and 26(Sikorsky S-40) and was found to be generally less than the resistance of either.

Dawson, John R↗
NASA NTRS1938

Tank Tests of a Model of One Hull of the Savoia S-55-X Flying Boat N.A.C.A. Model 46

A model of one of the twin hulls of the Italian Savoia S-55-X flying boat (N.A.C.A. Model 46) was tested in the N.A.C.A. tank according to the general method. The data obtained from these tests cover a broad range of speeds, loads, and trims and are given in nondimensional form to facilitate their use in applying this form of hull to any other flying boat or comparing it's performance with the performance of any other hulls. The results show that the resistance characteristics at best trim of this model are excellent throughout the speed range. In order to compare the performance of the S-55-X hull with that of the 35, a pointed-step hull developed at the N.A.C.A. tank, the data are used in the computations of take-off example of a twin-hull, 23,500-pound flying boat. The calculations show that the S-55-X hull has better take-off performance.

Allison, John M↗
NASA NTRS1937

Tank Tests of NACA Model 40 Series of Hulls for Small Flying Boats and Amphibians

The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.

Parkinson, John B↗
DOE OSTI2025

Coupled THM modeling of bentonite heating and hydration in tank tests with a new temperature-dependent water retention model

This study presents a coupled thermo-hydro-mechanical (THM) model for simulating the heating and hydration behavior of bentonite, a buffer material in deep geological repositories (DGRs). The model incorporates a new temperature-dependent soil water retention curve which captures the thermal-induced shift in water retention behavior. It also distinguishes between liquid and gas permeability, modeling intrinsic gas permeability as a function of accessible porosity to improve vapor transport and desaturation predictions. The model was validated against two large-scale tank tests, demonstrating good agreement with measured temperature, relative humidity, and water inflow data. It revealed a complex porosity evolution driven by thermal expansion, vapor movement, vapor condensation, and hydration-induced swelling during heating and hydration processes. The simulation results also suggest that the permeability of the hydration layer plays a critical role in controlling water intake. Clogging of this layer can significantly reduce the volume of water inflow during the hydration phase. Furthermore, while the model effectively captures key THM behavior, further development of the mechanical constitutive law is required to account for possible thermo-elasto-plastic volume changes and microstructural effects. Overall, the model provides a robust tool for evaluating the evolution of bentonite-based barrier material in DGRs.

Guo, Guanlong [Lawrence Berkeley National Laborato↗
NASA NTRS1934

A Complete Tank Test of the Hull of the Sikorsky S-40 Flying Boat - American Clipper Class

The results of a complete test in the N.A.C.A. tank on a model of the hull of Sikorsky S-40 flying boat ('American Clipper') are reported. The test data are given in tables and curves. From these data non-dimensional coefficients are derived for use in take-off calculations and the take-off time and run for the S-40 are computed. The computed take-off time was obtained by the Sikorsky Aviation Corporation in performance tests of the actual craft.

Dawson, John R↗
NASA NTRS1936

Tank Tests of a Model of the NC Flying-boat Hull - N.A.C.A. Model 44

A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive trimming moment than model 11-A. At high speeds the best trim angle and the trimming moments of the two models are approximately the same.

Bell, Joe W↗
NASA NTRS1946

Tank Tests of 1/5.5-Scale Forward Dynamic Model of the Columbia XJL-1 Amphibian - Langley Tank Model 208, TED No. NACA 2336

Tests of a powered dynamic model of the Columbia XJL-1 amphibian were made in Langley tank no.1 to determine the hydrodynamic stability and spray characteristics of the basic hull and to investigate the effects of modifications on these characteristics. Modifications to the forebody chime flare, the step, and the afterbody, and an increase in the angle of incidence of the wing were included in the test program. The seaworthiness and spray characteristics were studied from simulated taxi runs in smooth and rough water. The trim limits of stability, the range of stable positions of the enter of gravity for take-off, and the landing stability were determined in smooth water. The aerodynamic lift, pitching moment, and thrust were determined at speeds up to take-off speed.

Havens, Robert F.↗
NASA NTRS1936

Tanks Test of a Model of the Hull of the Navy PB-1 Flying Boat - N.A.C.A. Model 52

A model of the hull of the Navy PB-1 flying boat was tested in the N.A.C.A. tank as part of a program intended to provide information regarding the water performance of hulls of flying boats of earlier design for which hydrodynamic data have heretofore been unavailable. Tests were made according to the general method over the range of practical loadings with the model both fixed in trim and free to trim. A free-to-trim test according to the specific method was also made for the design load and take-off speed corresponding to those of the full-scale flying boat. The resistance obtained from the fixed-trim test was found to be about the same as that of the model of the NC flying-boat hull, and greater at the hump but smaller at high speeds than that of a model of the Sikorsky S-40 flying-boat hull.

Allison, John M↗
NASA NTRS1934

Tank tests of flat and v-bottom planning surfaces

Four planing surfaces, all having beams of 16 inches and lengths of 60 inches but varying in dead rise by 10 degrees increments from 0 degrees to 30 degrees, were tested in the N.A.C.A. tank. The results cover a wide range of speed, loads, and trim angles, and are applicable to a variety of problems encountered in the design of seaplanes. The data are analyzed to determine the characteristics of each surface at the trim angle giving minimum resistance for all the speed and loads tested. A planing coefficient intended to facilitate the application of the results to design work is developed and curves of resistance, wetted length, and center of pressure are plotted against this coefficient. Several examples, showing the application of the test data to specific design problems are included.

Shoemaker, James M↗
NASA NTRS1948

Tank Tests of a Powered Model of a Compression Plane, NACA Model 171A-2

The compression plane is intended for operation on or close to the surface of the water, and has a hull with a concave bottom which forms the upper surface of a tunnel into which air is forced under pressure to support part of the load. The results of the tests made in Langley tank no. 1 include values of the horizontal forces, trimming moment, and static pressure in the tunnel for a wide range of loads and speeds and two power conditions, and are presented in the form of curves against speed with load as a parameter. The results are scaled up to 10 times the model size for three conditions at which the model is self-propelled at a steady speed. Lift is obtained from the static pressure of air in the tunnel. In general, the ratio of the gross load to the total resistance increases with increase in load and decrease in speed. This ratio varies between l-7 and 5.7 at high speeds and has a maximum value of 7. The total resistance is nearly the same for both power conditions except at low speeds and heavy loads. No abrupt change in forces on the hull or flow around the hull occurs in. the region of zero draft. The centers of pressure are generally far aft. At the most efficient trim (1.2'), considerable bow-up moment would be required for practicable operation. There is no abrupt transition from the air-borne to the water- borne condition.

Mottard, Elmo J.↗
NASA NTRS1936

Tank Tests of the Effect of Rivet Heads, etc., on the Water Performance of a Seaplane Float, Special Report

A 1/3.5 full-size model of the Mark V float of the Bureau of Aeronautics, Navy Department, was tested in the NACA tank both with smooth painted bottom surfaces and with roundhead rivets, plate laps, and keel plates fitted to simulate the actual bottom of a metal float. The augmentation in water resistance due to the added roughness was found to be from 10-12% at the hum speed and from 12-14% at high speeds. The effect of the roughness of the afterbody was found to be negligible except at high trims. The model data were extrapolated to full size by the usual method which assumes the forces to vary according to Froude's law, and in the case of the smooth model by a method of separation that takes into account the effect of scale on the frictional resistance. It was concluded that the effect of rivet heads on the takeoff performance of a relatively high-powered float seaplane is of little consequence but that it may be of greater importance in the case of more moderately powered flying boats.

Parkinson, J. B.↗