Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRITIUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Fundamental Studies of Tritium Diffusivity in Pure and Defective Zircaloy-4 Getters (Tritium Science Program FY2020 Report)

Zirconium (Zr) alloys are extensively used as tritium (T) getters in nuclear reactors due to their low absorption cross section to thermal neutron, good mechanical properties at high temperature and resistant to corrosion in different environmental conditions. Zr alloys have better thermal properties than many other refractory alloys including stainless steel. The nuclear characteristic is simulated, and T is produced in tritium-producing burnable absorber rods (TPBAR) by the irradiation of neutron flux in pressurized water reactor (PWR). T thus produced diffuses through the pellets and is captured by the getter where it chemically reacts with Zr to form metal hydride (ZrTx). These hydrides are brittle and affect adversely the mechanical properties of alloys. In addition to that, mismatch in the lattice structures after hydride formation creates a stress which needs to be considered in component design and their life evaluation. Therefore, understanding the behavior of T and its species becomes significant as fuel burnup is increased, which leads to increase in hydrogen pickup and oxide formation. The transport of T and its species in pure Zr alloys, and in alloys with certain alloying elements and defects are important to understand in order to enhance the performance of the materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A quantitative study of retention and release of deuterium and tritium during irradiation of y-LiAlO2 pellets

This study reports on the quantification of deuterium in ion-irradiated gamma-LiAlO2 pellets as a function of dose and temperature. The gamma-LiAlO2 pellets were sequentially irradiated with He+ and D2+ ions to the same fluences of 5E16, 1E17 and 2E17 He++D+/cm2 at 188 K. Additional irradiation was performed to 1E17, 2E17 and 4E17 He++D+/cm2 at 573 K. A set of the pellets irradiated at 188 K was shipped and stored at low temperatures from 80 to 132 K and characterized using time-of-flight secondary ion mass spectrometry at ~173 K. The deuterium depth profiles show a Gaussian-like distribution in the low-temperature pellets. The total deuterium retention is found to be directly proportional to the ion fluence. About 27 at.% of the implanted deuterium atoms were released from the pellet irradiated to 2E17 He++D+/cm2 at 188 K during storage at room temperature for ~1 month. Retention of the trapped or bound deuterium during ion irradiation at 573 K increases initially with ion fluence and tends to saturate at a high fluence. The amount of the released deuterium is observed to be quantitatively consistent with that of the released tritium from similar standard pellets during neutron irradiation at 573 K.

Deuterium retention and release, ion irradiation, ↗
DOE OSTI2020

Theoretical study of the electronic, thermodynamic, and thermo-conductive properties of y-LiAlO2 with 6Li isotope substitutions for tritium production

Lithium aluminate has attracted researchers’ interests due to its wide applications. The structural, electronic, optical, lattice phonon thermodynamic, and thermo-conductive properties of ?-LiAlO2 with 6Li-isotope substitution are investigated by density functional theory and lattice phonon dynamics. The calculated results show that ?-LiAlO2 possesses a wide band-gap of 4.63 eV. The valence band is mainly formed by p orbitals of Li, O, and Al. The calculated lattice thermal conductivity of ?-LiAlO2 is found to be in good agreement over a wide range of temperatures with the available experimental data. The calculated dielectric matrix shows anisotropic behavior along z and x (or y) axes. Due to the wide band-gap, the optical conductivity of ?-LiAlO2 is mainly contributed from the electron hopping between valence-conduction bands. Substitution of 7Li with 6Li isotope in ?-LiAlO2 leads to observable differences in the lattice phonon frequencies at higher frequencies (>8THz) and to slight changes in corresponding thermal conductivity and the infrared and Raman spectra which are in good agreement with the measured data. The relevance of these properties for tritium production through 6Li absorbing neutron in nuclear reactors is discussed.

ab initio thermodynamics, ?-LiAlO2 and 6Li-isotope↗
DOE OSTI2020

Evaluation of Detritiation Strategies for Mitigating Tritium Releases

Tritium confinement is performed using different barriers to minimize releases to the environment. Primary confinement is usually performed by process piping and components, secondary confinement typically by inerted gloveboxes connected to a continuously operating tritium stripper system. Some facility designs employ tertiary tritium confinement by using process room confinement with a tritium stripper system activated after an accident to further mitigate tritium releases to the environment. Secondary confinement of some tritium systems such as radiation-hardened or shielded-cell enclosures are not easily achieved using designs for inerted glovebox. These enclosures can be challenging to seal for secondary tritium confinement due to heating, ventilation, and air conditioning (HVAC) needs for temperature control, as well as feedthroughs for equipment and instrumentation, are potential pathways for tritium leaks or loses. Additional tritium leak paths can be created in secondary confinement enclosures due to a Design Basis Accident (DBA) seismic event. These new, larger tritium leak rates from the DBA event are usually not part of the stripper system design basis so all tritium released to the secondary confinement enclosure is assumed released to the environment. Detritiation strategies for shielded enclosures and/or gloveboxes with significant leak rates are necessary to minimize off-site radiological dose consequences. To address this, the relationship between the confinement system leak rate and stripper system (recirculating) flow rate was evaluated to meet prescribed maximum allowable environmental tritium emissions from the event. The simple analysis described assumes a constant leak rate from the confinement system (i.e. shielded enclosure or glovebox) while a recirculating stripper system strips tritium from the system– a competition between tritium release and tritium recovery. At a high level, the resulting expression summarizes the relationship between system leak rate (F L ) and stripper flow rate (F S ) relative to allowable tritium release (Q A ) and initial tritium release (Q 0 ): $\frac{F_L}{F_s}$ ≈ $\frac{Q_A}{Q_0}$. This report derives the relationship between these parameters, examines the impact of finite stripping times followed by purging of the stripped volume. The analysis provides example results for up to 30 gram tritium releases: the maximum tritium inventory of a Hazard Category III (Department of Energy) Nuclear Facility. The detritiation model presented represents a high-level analysis of tritium recovery versus losses for “leaky” confinement enclosures such as shielded cells after large tritium releases. Key parameters for doing the analyses are the system leak rate, stripper flow rate, initial tritium release, and allowable tritium release values. The analyses show a proportional decrease in releases with reduction in initial tritium release but a non-linear increase in tritium recovery with increased stripper flow rate or reduced leak-rate. The analyses also apply to glovebox confinement systems which could have significant increases in leak rates after a DBA. The analysis recognizes but does not include tritium absorption followed by re-emission from the walls of the confinement volume – an analysis which could be pursued in future studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Tritium Safety: Self-Study Course 11952

Course Overview: Tritium is a radioactive isotope of hydrogen which has characteristics that require workers understand what should be done to work safely and responsibly around it. Tritium is used for defense applications, experimental purposes for general research, and is a byproduct of some of the work that is done at LANL. Practical guidance offered in this training will inform safe handling to minimize negative impacts on personnel, the workspace, and the surrounding environment. This course, Tritium Safety Self-Study (Course 11952), provides information on the physical, chemical, and radioactive properties of tritium; sources of tritium; uses of tritium; biological effects of tritium; radiological control methods for tritium; monitoring methods of tritium; tritium waste minimization and handling; and alarms and proper response to abnormal conditions in a tritium facility. Course Objectives: When you have completed this course, you will be able to: Identify the physical, chemical, and radioactive properties of tritium; Identify the sources of tritium; Identify the uses of tritium; Identify the modes of tritium exposure; Identify the biological effects of tritium; Identify the radiological control methods of tritium; Identify methods used to monitor for tritium; Identify tritium waste minimization and handling techniques; Identify proper response to abnormal conditions in tritium facilities.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2021

Spatial and temporal variability of tritium in precipitation within South Africa and it's bearing on hydrological studies

Tritium, the radioactive isotope of hydrogen, has been used to understand groundwater recharge processes for decades. The current variation of tritium in the atmosphere is largely attributed to stratospheric production and fall out rates as well as global circulation phenomena controlling the hydrological cycle. Global controls on the variability in atmospheric tritium activity are poorly suited to explain local variation and tritium activities in precipitation are often assumed to be uniform over both local and regional catchments and watersheds. This assumption can result in both over and under estimation of modern recharge within an aquifer when using tritium as the recharge proxy. In order to minimize the inherent prediction residuals associated with tritium based recharge investigations, the variability of tritium in precipitation was modelled from 127 spatial precipitation samples taken over a two year period, combined with a 76 precipitation sample group-set taken over a one year period in a single location. Precipitation events were traced backward in time, from the point of collection, using HYSPLIT modelling to ascertain the origins of moisture content as well as the altitudes of moisture origin reached along the particle track. Tritium activities, collected over a one year period in Paarl, range from 0.45 to 4.16 TU and have a mean of 1.59 TU. Spatial storm events in the Western Cape in 2017 and 2018 had a range from 0 to 2.2 and 0.37 to 3.27 TU, respectively, with mean activities of 1.18 (n = 34) and 1.25 TU (n = 32). Both storm events had similar tritium variability (σ = 0.5 n = 35 and 0.48 n = 32). Regional precipitation events had the largest range of tritium activities (0.55–12.2 TU). Although not all tritium activities can be explained by interrogating the water mass origin, this study suggests that approximately 90% of events can be completely or partially attributed to the origin of the water mass. The variability of tritium, both spatially and temporally, was higher than expected, confirming that when uniform tritium inputs are used, the groundwater system would provide inaccurate modern recharge estimates. Higher spatial resolution of tritium variation in precipitation for a particular region will improve our ability to relate tritium activities in groundwater to local precipitation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Conceptual design for a blanket tritium extraction test stand

Tritium breeding is fundamentally required for a sustainable fusion fuel cycle, yet the technological readiness of blanket technology lags far behind other fusion systems. Breeder concepts are divided into solid and liquid media, where solid breeders typically rely on a sweep gas, such as helium, to carry away tritium from lithium containing ceramic materials, and liquid breeders produce tritium from lithium containing eutectics (e.g., PbLi) or molten salts (FLiBe). In each case, tritium must be harvested from the breeding medium. A promising method for tritium extraction is through a vacuum permeator, in which a concentration gradient from the tritium- containing fluid promotes diffusion through a membrane with high hydrogen permeability to the vacuum. This technology has been demonstrated for hydrogen gas systems using Pd and PdAg permeators, but relatively little work has been done to test tritium extraction from PbLi. A Tritium Extraction eXperimental (TEX) loop is being designed to test tritium extraction in a vacuum permeator configuration. The system design is such that it will allow the testing of tritium extraction from both helium and PbLi. A phased approach is being taken that will allow testing of small specimens for fundamental permeation measurements, to multi-meter component testing at near-prototypic conditions. A molten PbLi loop is challenging due to the toxic and explosive nature of Pb and Li, respectively, radiological concerns by introducing tritium, and high temperatures involved in such a system. In addition, PbLi corrosion is a significant issue at high temperatures (>400C). The TEX system will not employ a neutron source for volumetric production of tritium. Herein we present the design and methods used for 1) pumping PbLi, 2) introducing deuterium or tritium into the PbLi, 3) quantifying the amount of deuterium in the loop, 4) extracting deuterium and tritium, and 5) quantifying the total amount of extracted deuterium or tritium from the permeator. In addition, the safety design for operating such a system will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Evaluating the Impact of Tritium Permeation Membrane Performance and Direct Internal Recycling on Fusion Fuel Cycle Efficiency Using TMAP8

An efficient fuel cycle is vital to sustainable and cost-effective energy generation in fusion systems. Since tritium is not widely available, fusion systems must breed their own tritium for sustainable fusion deuterium-tritium reactions. An inefficient fuel cycle increases the tritium inventory needed for operations, which increases costs, constraints on tritium management systems, and safety concerns. A fuel cycle model is a powerful tool for understanding tritium inventories and flow rates across all systems in the fuel cycle. By simplifying the technical details into time-dependent tritium flow rates and inventories, the model can simulate the entire fuel cycle with high computational efficiency, even for technologies that are still under development. It can therefore quantify the impact of new tritium management technologies on fuel cycle efficiency. To evaluate the impact of key components on reducing tritium inventory, we are using and expanding an existing fuel cycle models based on latest advancements in fuel cycle research. The new model integrates Tritium Permeation Membrane (TPM) and Direct Internal Recycling (DIR) to enhance tritium transport from blanket breeders and plasma exhaust. These fuel cycle models are implemented in TMAP8 (Tritium Migration Analysis Program, version 8), a MOOSE-based open-source application designed to provide cutting-edge capabilities for tritium transport and fuel cycle modeling. The study aims to demonstrate the extensibility of existing fuel cycle modeling capability in TMAP8 and to offer a proof-of-principle design for future fusion plant systems. The presentation will cover the performance of fuel cycle modeling capabilities available in TMAP8, highlight advancements in fuel cycle research, and present a sensitivity analysis of these models. The results underline potential approaches and technology solutions to lower tritium inventory requirements, highlighting their role in shaping the future of fusion energy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Thermodynamics of Tritium Trapping by Point Defects in Intermetallic Al 12 (TM) 2.35 Aluminide Coating Phase

Density functional theory simulations have been carried out to investigate the potential for tritium trapping by metal vacancies in intermetallic Al 12 (TM) 2.35 phase (TM = Fe, Cr, and Ni) as function of temperature and tritium partial pressure. It was found that tritium could be favorably trapped by Fe and Ni vacancies and not favorably trapped by Al and Cr vacancies. However, due to the presence of partially occupied Al sites in bulk Al 12 (TM) 2.35 , leading to the approximate number of ~255 Al atoms in the unit cell, 86 sites were found energetically favorable to the creation of an Al vacancy. While adding a tritium atom in an Al vacancy is not energetically favorable, the tritiated defect still has a negative Gibbs free energy because the energy gain for creating an Al vacancy overcome the energy cost of adding the tritium species. Based on the calculated Gibbs free energy, the first tritiation of a metal vacancy, at conditions relevant to in-reactor operations, should be more favorable for Al, followed Fe, Ni, and Cr vacancies. By comparing the behavior of tritium in Al 12 (TM) 2.35 with previously studied Fe-Al coating phases (i.e., FeNiAl 5 , Fe 4 Al 13 , and Fe 2 Al 5.6 ), we found that there is a correlation between interstitial tritium solubility and the potential for vacancy trapping. The current trend suggests that if the insertion of an interstitial tritium cost more than 0.3 eV, then trapping by metal vacancies should be preferred. By combining the simulations results obtained to date, we noticed different trapping mechanisms of tritium in the Al coating. Tritium is mostly trapped by Fe and Ni vacancies in the outer Fe-Al coating phase Al 12 (TM) 2.35 while tritium should be preferentially trapped by Al and Fe vacancies for the inner Fe-Al coating phases (FeNiAl 5 , Fe 4 Al 13 , Fe 2 Al 5.6 ). Altogether, these studies show that tritium interacts differently with the various Fe-Al aluminide phases, they also suggest that tritium trapping and retention could be more efficient if metal defects are present and if the solubility of interstitial tritium in the different phases is low.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Microstructure on the Absorption of Tritium into Gold-Plated 316 Stainless Steel

The interaction of tritium with metal surfaces is the initial step in the overall absorption of tritium by the substrate metal. As a result, limiting the adsorption of tritium to the surface may effectively reduce the quantity of tritium absorbed by a metal when it is in contact with tritium gas. To limit tritium adsorption, many tritium users electroplate gold onto the substrate metal. The gold layer is expected to reduce tritium adsorption, and subsequently absorption, by reducing water adsorption. The present work shows a comparison between tritium inventories in nonplated 316 stainless steel to the inventories in 316 stainless-steel samples electroplated with gold by various commercial vendors and laboratories. Of the various gold-plated samples, only one type of plating shows ~25% reduction in tritium inventory, relative to non-plated steel samples. The degree of tritium absorption appears to be significantly influenced by the porosity, texture, and completeness of the gold layer. Incomplete and/or porous layers lead to increased absorption, while gold layers with smaller surface features lead to similar tritium inventories as non-plated samples. Furthermore, reduced tritium absorption was observed only for complete gold layers with small surface features.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

SR19021 Tritium Aging of Regenerated LANA.75 (Final Project Report)

The Savannah River Tritium Enterprise (SRTE) has used the metal hydride LaNi 4.25 Al 0.75 (LANA.75) in the Tritium Facilities for over two decades. LANA.75 beds store significant quantities of tritium but have a limited service life due to the radiolytic decay of tritium to He-3 within the metal matrix. It has been shown that heating tritium-aged LANA.75 under vacuum can reverse tritium aging effects, eliminating the heel of trapped hydrogen, and restoring the reversible capacity. Additional investigation is needed to ensure there are no unexpected changes to the hydride before this restoration technique is employed in full scale beds in the Tritium Facilities. This project was to be comprised of three distinct scopes: obtain tritium aging data on the sample regenerated in 2018, regenerate a tritium-aged sample at 600 °C, and perform thermal stability testing on a non-tritiated sample. Isotherms were collected on the previously regenerated sample after approximately two years of tritium aging. Isotherms were collected at 80, 100, and 120 °C. As expected, there was a decrease in the plateau pressure, an increase in plateau slope, and a portion of the “heel” of tritium trapped in the metal had been reestablished. Unexpectedly, it appeared that the plateau had shortened at the higher tritium to metal ratios as well. This is typically seen in older samples. The second scope, to regenerate a second tritium-aged LANA.75 sample, was not completed. A Task Technical and Quality Assurance Plan was written and approved, a high temperature test cell was fabricated, several pre-job briefs were held, and the hydride sample was passivated with air. Despite these successes, the hydride sample was not recovered from the legacy test cell. The third scope was to perform thermal stability testing on a “cold” LANA.75 sample. A non-tritiated sample of LANA.75 was held at 750 °C under vacuum for 200 hours to simulate exposure to multiple regeneration evolutions. Hydride isotherm performance, chemical composition, crystallinity, particle size, and morphology are compared between the pre- and post-regeneration samples. No significant changes were observed in composition, crystallinity, or particle size. Comparison of before and after isotherms showed that performance improved rather than deteriorated during the evolution. Scanning Electron Microscopy (SEM) analysis showed small growths on the particle surface after exposure to regeneration conditions. Additional testing will be required to determine the cause of these growths.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2023

Flammability and dispersion of tritium in confined release scenarios

Ignition of a flammable tritium-air mixture is the most probable means to produce the water form (T 2 O or HTO), which is more easily absorbed by living tissue and is hence ~10,000 times more hazardous to human health when uptake occurs compared to the gaseous form (T 2 or HT; per Mishima and Steele, 2002). Tritium-air mixtures with T 2 concentrations below 4 mol% are considered sub-flammable and will not readily convert to the more hazardous water form. It is therefore desirable from a safety perspective to understand the dispersion behavior of tritium under different release conditions, especially since tritium is often stored in quantities and pressures much lower than is typical for normal hydrogen. The formation of a flammable layer at the ceiling is a scenario of particular concern because the rate of dispersion to nonflammable conditions is slowest in this configuration, which maximizes the time window over which the flammable tritium may encounter an ignition source. This report describes the processes of buoyant rise and dispersion of tritium. Accumulation of flammable concentrations of tritium next to the ceiling is a common safety concern for hydrogen, but this situation can only occur if dispersion rates are slow with respect to rates of release and rise. Theory and simulations demonstrate that buoyancy does not cause regions with flammable concentrations to form within buildings from sources that have previously been mixed to sub-flammable concentrations. A simulated series of tritium release events with their associated dispersion behavior are reported herein; these simulations apply computational fluid dynamics to rooms with three different ceiling heights and a variety of tritium release rates. Safety related quantities from these simulations are reported, including the mass and volume of tritium occurring in a flammable mixture, the presence or absence of a flammable layer at the ceiling, and the time required for dispersion to nonflammable conditions after the end of the tritium release event. These safety metrics are influenced by the magnitude and rate of the tritium release with respect to the air volume in the room and also the momentum of the plume or jet with respect to the ceiling height. Several screening criteria are recommended to assess whether a specific tritium release scenario is likely to form a flammable layer at the ceiling. The methods and results in this modeling study have applicability to explosion safety analysis for other buoyant flammable gases, including the lighter isotopes of hydrogen.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Effect of Mg and Ni impurities on tritium diffusion in lithium ceramics through cluster dynamics simulations

This study investigates the impact of Mg and Ni doping on tritium diffusion in LiAlO 2 and LiAl 5 O 8 ceramics, that are used in tritium-producing burnable absorber rods (TPBARs). Utilizing Centipede simulations across a broad temperature range (500 K to 1250 K), we explore the interplay between defect dynamics, cluster formation, and tritium mobility. In LiAlO 2 , Mg doping significantly enhances tritium diffusivity by increasing tritium interstitial concentrations and diffusion coefficients of key species, thereby doubling the overall tritium diffusivity. Ni doping, while shifting the dominant defect to Li vacancies, maintains high tritium mobility due to the low binding energy of Li vacancy-tritium complexes, which ensures effective tritium migration. In LiAl 5 O 8 , Mg and Ni doping results in a slight reduction in the diffusion coefficients of key species, yet the dramatic increase in tritium interstitial concentrations compensates, leading to a net small increase in tritium diffusivity. In conclusion, the findings highlight the critical role of defects in tritium transport and the effect of Mg and Ni defects on the performance of these ceramics in demanding nuclear environments.

Cluster dynamics↗
DOE OSTI2020

Tritium generation, release, and retention from in-core fluoride salt irradiations

Further understanding of tritium transport mechanisms in the combined molten fluoride salt and graphite environment is necessary for the design and licensing of a Fluoride-Salt-Cooled High-Temperature Reactor (FHR). The three in-core fluoride salt irradiations completed at the Massachusetts Institute of Technology Reactor (MITR) are a useful parallel for studying transport phenomena expected in a FHR environment. During the irradiations, evolution of tritium from the flibe salt was monitored and compared to the calculated total generation rate. A difference of 22 ± 10% between the integrated calculated tritium generation rate and the total release was measured for the third MITR irradiation (FS-3). The fraction of tritium which was not released from the salt could be explained by tritium retention in graphite. Additionally, for post irradiation examination, a thermal desorption furnace was used to heat nuclear graphite samples in order to release and measure retained tritium. The desorption analysis in this work utilized seven subsections of graphite from the second salt irradiation (FS-2); three from a disc of IG-110U and four from ARB matrix graphite. Observed desorption versus temperature as well as total tritium content in the samples after irradiation indicate that the graphites were not volumetrically saturated with tritium, but rather tritium retention was likely limited to the near-surface region. Measurements of the samples resulted in 2.90 ± 0.29 μCi/mm 2 of tritium retained by IG-110U and 1.83 ± 0.31 μCi/mm 2 for ARB during the 300 h FS-2 in-core irradiation. Based on the desorption measurements, the estimated total tritium retention in graphite from the FS-2 samples is consistent with the tritium release measurements from the FS-3 experiment.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Calibration of a mesoscale tritium transport model for ceramic breeder materials in TMAP8 using experimental data

Due to the scarcity of the long-term external tritium supply, lithium-containing breeder materials are used in the blanket of fusion reactors to produce tritium faster than the deuterium-tritium fusion reaction consumes it. A cellular breeder is a promising material with higher lithium density and thermal conductivity than conventional ceramic pebbles and enhanced tritium extraction with interconnected pores. Although several experimental and modeling efforts have improved our understanding of tritium transport, the exact mechanisms governing tritium release from breeder materials are still unknown. As a result, current models cannot reliably assess the tritium breeding capabilities of cellular breeder materials. This work presents a tritium transport multiphysics model and calibrates it using experimental data of deuterium absorption and desorption from cellular breeder materials at different temperatures and pressures. This model accounts for ceramic and pore diffusion, trapping and detrapping, and several surface reactions at the pore surface. After calibrating the model and performing sensitivity analysis, we discuss pre-dominant mechanisms governing tritium release from cellular breeder materials. The model is part of the Tritium Migration Analysis Program [TMAP8], a multiscale, multiphysics framework for tritium transport based on the finite element multiphysics framework MOOSE. This study demonstrates some of TMAP8’s capabilities and provides insight into the mechanisms governing tritium transport in cellular ceramic breeder materials.

08 HYDROGEN↗
DOE OSTI2025

Logical approach to tritium vacuum pump selection for fusion applications

Vacuum pumps have been used for tritium processing since the 1940s following the isolation of pure tritium. The largest problem facing tritium vacuum pumps is the tritium radioactive decay. The beta particles, recoil energy, and subsequent radical formations are detrimental to most carbon-based materials. Carbon materials, such as plastics, elastomers, carbon fiber, activated carbon, etc., react with tritium to form methane and in the process strip material from the carbonbased material. Other reactions can be self-catalyzing, as is the case with nitrogen and tritium forming tritiated ammonia at room temperature and pressure. Tritium also readily isotopically exchanges with surface -OH groups, increasing the amount of protium in the gas stream while creating a tritium holdup on the surface. Metals are the preferred material when working with tritium, but tritium will permeate into and through almost all metals at some point. The entrapped tritium can decay inside the metal, creating local helium distortions that can impact the structural properties above and beyond the hydrogen embrittlement issue tritium can cause.

Angelette, Lucas M. [Savannah River National Labor↗
DOE OSTI2023

Modeling and analysis of the tritium fuel cycle for ARC- and STEP-class D-T fusion power plants

Abstract The limited tritium resources available for the first fusion power plants (FPPs) make fuel self-sufficiency and tritium inventory minimization leading issues in FPP design. This work builds on the model proposed by Abdou et al (2020 Nucl. Fusion 61 013001), which analyzed the fuel cycle (FC) of a DEMOnstration nuclear FPP-class FPP with a time-dependent system-level model. Here, we use a modified version of their model to analyze the FC of an Affordable, Robust, Compact (ARC)-class tokamak and two versions of a Spherical Tokamak for Energy Production (STEP)-class tokamak. The ARC-class tokamak breeds tritium in a 2LiF + BeF 2 liquid immersion blanket, while the STEP-class tokamak breeds tritium utilizing either a liquid-lithium blanket design or an encapsulated breeding blanket. A time-dependent system-level model is developed in Matlab Simulink ® to simulate the evolution of tritium flows and tritium inventories in the FC. The main goals of this work are to assess tritium self-sufficiency of the ARC- and STEP-class designs and to determine quantitative design requirements that can be used to analyze the adequacy of a proposed FC system. These design requirements are aimed at achieving a low tritium inventory doubling time ( t d ) and a low start-up inventory ( I s t a r t u p ) while keeping the required tritium breeding ratio (TBR r ) as low as possible. We also consider how improvements in FC technology and POs affect TBR r and I s t a r t u p . The model results show that TBR r for ARC- and STEP-class FPPs should be achievable if the tritium burn efficiency (TBE) reaches 0.5%–1% (TBR r < 1.2). This assumes significant, but attainable, improvements over current abilities. However, the model results indicate that an FPP must achieve ambitious performance targets, including FPP availability > 70%, tritium processing time < 4 h, and the implementation of direct internal recycling (DIR). If future research yields major improvements to achievable TBE, it may be possible to achieve tritium self-sufficiency while operating at lower availability and without implementing DIR.

Physics↗
DOE OSTI2021

Assessment of tritium effluent from Prototype Generation IV Sodium-cooled Fast Reactor

We report a tritium transport model for a pool-type sodium cooled fast reactor was developed for estimation of tritium effluents from the Prototype Generation IV Sodium-cooled Fast Reactor (PGSFR). For this purpose, the transport model developed for Experimental Breeder Reactor II and Fast Flux Test Facility was updated and validated. The tritium production rate from ternary fission and activations in PGSFR were calculated by the Argonne Reactor Computation (ARC) code suite for fast reactor analysis, and due to the potential uncertainties in source terms and variations of cold trap performance and material permeability during reactor operation, the tritium distributions and tritium effluents were estimated for several bounding cases. The upper bounding gaseous and liquid tritium release rates from PGSFR are similar to ~440.7 Ci/year and 14.7 Ci/year, respectively. The gaseous tritium effluent is about few orders of magnitude smaller than the regulatory constraint of the tritium concentration in the air. The peak tritium concentration in the steam-generator feedwater is similar to ~1.1x10 -3 mu Ci/g, which is required to be diluted prior to releasing as tritiated water. The accumulated tritium in the cold trap after five cycle operations is ~ 52,000 Ci. Because of significant conservatism in these upper bounding estimations, it is expected that the tritium effluent at the nominal case with plausible source terms would be about 2 orders of magnitude smaller than that of the upper bounding case.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗