Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TENSILE PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca-xSn Alloys

The microstructure, tensile properties, and corrosion behavior of die-cast Mg-7Al-1Ca-xSn (x = 0, 0.5, 1.0, and 2.0 wt.%) alloys were studied using OM, SEM/EDS, tensile test, weight loss test, and electrochemical test. The experimental results showed that Sn addition effectively refined grains and intermetallic phases and increased the amount of intermetallic phases. Meanwhile, Sn addition to the alloys suppressed the formation of the (Mg,Al){sub 2}Ca phase and resulted in the formation of the ternary CaMgSn phase and the binary Mg{sub 2}Sn phase. The Mg-7Al-1Ca-0.5Sn alloy exhibited best tensile properties at room temperature, while Mg-7Al-1Ca-1.0Sn alloy exhibited best tensile properties at elevated temperature. The corrosion resistance of studied alloys was improved by the Sn addition, and the Mg-7Al-1Ca-0.5Sn alloy presented the best corrosion resistance.

36 MATERIALS SCIENCE↗

Effect of aging treatment on microstructures, tensile properties and intergranular corrosion behavior of Al–Cu–Li alloy

Highlights: • T8 duplex aging greatly promoted the precipitation of strengthening phases. • Heavy precipitation of strengthening phases led to enhancing of tensile properties. • Intergranular corrosion sensibility can be reduced by T8 duplex aging greatly. - Abstract: The influence of aging treatment on microstructures, tensile properties and corrosion properties of Al–Cu–Li alloy was investigated. The results show that the T8 duplex aging treatment was more effective than T6 and T8 single aging treatment in enhancing the tensile properties and improving the intergranular corrosion (IGC) resistance. Based on the microstructure observation, tensile test, electrochemical experiment and IGC measurement, the factors which affect the microstructures, tensile properties and IGC behavior changing of Al–Cu–Li alloy during aging treatments were discussed in detail.

36 MATERIALS SCIENCE↗

Report on Thermal Aging Effects on Tensile Properties of Ferritic-Martensitic Steels.

This report provides an update on the evaluation of thermal-aging induced degradation of tensile properties of advanced ferritic-martensitic steels. The report is the first deliverable (level 3) in FY11 (M3A11AN04030103), under the Work Package A-11AN040301, 'Advanced Alloy Testing' performed by Argonne National Laboratory, as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing tensile data on aged alloys and a mechanistic model, validated by experiments, with a predictive capability on long-term performance. The scope of work is to evaluate the effect of thermal aging on the tensile properties of advanced alloys such as ferritic-martensitic steels, mod.9Cr-1Mo, NF616, and advanced austenitic stainless steel, HT-UPS. The aging experiments have been conducted over a temperature of 550-750°C for various time periods to simulate the microstructural changes in the alloys as a function of time at temperature. In addition, a mechanistic model based on thermodynamics and kinetics has been used to address the changes in microstructure of the alloys as a function of time and temperature, which is developed in the companion work package at ANL. The focus of this project is advanced alloy testing and understanding the effects of long-term thermal aging on the tensile properties. Advanced materials examined in this project include ferritic-martensitic steels mod.9Cr-1Mo and NF616, and austenitic steel, HT-UPS. The report summarizes the tensile testing results of thermally-aged mod.9Cr-1Mo, NF616 H1 and NF616 H2 ferritic-martensitic steels. NF616 H1 and NF616 H2 experienced different thermal-mechanical treatments before thermal aging experiments. NF616 H1 was normalized and tempered, and NF616 H2 was normalized and tempered and cold-rolled. By examining these two heats, we evaluated the effects of thermal-mechanical treatments on material microstructures and associated mechanical properties during long-term aging at elevated temperatures. Thermal aging experiments at different temperatures and periods of time have been completed: 550°C for up to 5000 h, 600°C for up to 7500 h, and 650°C for more than 10,000 h. Tensile properties were measured on thermally aged specimens and aging effect on tensile behavior was assessed. Effects of thermal aging on deformation and failure mechanisms were investigated by using in-situ straining technique with simultaneous synchrotron XRD measurements.

36 MATERIALS SCIENCE↗

Influences of post-weld heat treatment on tensile properties of friction stir-welded AA6061 aluminum alloy joints

This paper reports on studies of the influences of various post-weld heat treatment procedures on tensile properties of friction stir-welded AA6061 aluminum alloy joints. Rolled plates of 6-mm thick AA6061 aluminum alloy were used to fabricate the joints. Solution treatment, an artificial aging treatment and a combination of both were given to the welded joints. Tensile properties such as yield strength, tensile strength, elongation and joint efficiency were evaluated. Microstructures of the welded joints were analyzed using optical microscopy and transmission electron microscopy. A simple artificial aging treatment was found to be more beneficial than other treatment methods to enhance the tensile properties of the friction stir-welded AA6061 aluminum alloy joints.

36 MATERIALS SCIENCE↗

Effects of Laser Energies on Wear and Tensile Properties of Biomimetic 7075 Aluminum Alloy

Inspired by the non-smooth surface of certain animals, a biomimetic coupling unit with various sizes, microstructure, and hardness was prepared on the surface of 7075 aluminum alloy. Following experimental studies were conducted to investigate the wear and tensile properties with various laser energy inputs. The results demonstrated that the non-smooth surface with biomimetic coupling units had a positive effect on both the wear resistance and tensile property of 7075 aluminum alloy. In addition, the sample with the unit fabricated by the laser energy of 420.1 J/cm{sup 2} exhibited the most significant improvement on the wear and tensile properties owing to the minimum grain size and the highest microhardness. Also, the weight loss of the sample was one-third of the untreated one’s, and the yield strength, the ultimate tensile strength, and the elongation improved by 20, 20, and 34% respectively. Moreover, the mechanisms of wear and tensile properties improvement were also analyzed.

36 MATERIALS SCIENCE↗

High-temperature tensile properties of fiber reinforced reaction bonded silicon nitride

Measurements of tensile properties of unidirectional silicon carbide fiber-reinforced reaction-bonded silicon nitride (SiC/RBSN) composite specimens were carried out in air at 25, 1300, and 1500 C, using a new testing technique and a specially designed gripping system that minimizes bending moment and assures that failure always occurred in the gage section. The material was found to display metallike stress-strain behavior at all temperatures tested, and a noncatastrophic failure beyond the matrix fracture. The tensile properties were found to be temperature dependent, with the values of the ultimate tensile strength decreasing with temperature, from 543 MPa at 25 C to 169 at 1500 C.

Jablonski, David A.↗

Report on Thermal Aging Effects on Tensile Properties of Advanced Austenitic Steels

This report provides an update on the evaluation of thermal-aging induced degradation of tensile properties of advanced HT-UPS austenitic stainless steels. The report is the second deliverable (level 3) in FY11 (M3A11AN04030103), under the Work Package A-11AN040301, “Advanced Alloy Testing” performed by Argonne National Laboratory, as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing tensile data on aged alloys and a mechanistic model, validated by experiments, with a predictive capability on long-term performance. The scope of work is to evaluate the effect of thermal aging on the tensile properties of advanced alloys such as ferritic-martensitic steels, mod.9Cr-1Mo (G91), G92, and advanced austenitic stainless steel, HT-UPS. The aging experiments have been conducted over a temperature of 550-750°C for various time periods to simulate the microstructural changes in the alloys. In addition, a mechanistic model based on thermodynamics and kinetics has been used to address the changes in microstructure of the alloys as a function of time and temperature, which is developed in the companion work package at ANL. The focus of this project is advanced alloy testing and understanding the effects of long-term thermal aging on the tensile properties. The first deliverable of FY11 reported the tensile testing results of thermally-aged G92 in the normalized and tempered condition (H1 G92), G92 in the cold-rolled condition (H2 G92), and reference alloy, G91 ferritic-martensitic steels. This report summarizes the tensile data of thermally aged HT-UPS austenitic stainless steel. Two heats of HT-UPS have been investigated, i.e., solution-annealed HT-UPS (SA HT-UPS) and hot-rolled HT-UPS (HR HT-UPS). Tensile data have been obtained for SA HT-UPS thermally-aged for up to 18031 h at 550°C and for up to 17595 h at 650°C, as well as for HR HT-UPS thermally aged for up to 6909 h at 550°C, 4293 h at 600°C, and 5407 h at 650°C. Major finding are: (1) the solution-annealed HT-UPS showed continued, moderate increase in strength and decrease in ductility with increasing aging time up to 18034 h at 550°C. Thermal aging at 650°C increased the yield stress and decreased the ultimate tensile strength and drastically reduced the ductility in the SA HT-UPS. For the HR HT-UPS, thermal aging at 550°C for up to 6909 h showed little influence on its tensile behavior. Thermal aging at 600°C for 4293 h increased the strength and decreased the ductility. The 650°C-thermally-aged HR HT-UPS specimens showed very different strengthening, strain hardening, and flow localization behavior. Thermal aging at 650°C increased the yield stress but decreased the ultimate tensile stress for the HR HT-UPS. (2) Dynamic strain aging (DSA) was observed in both the solution-annealed HT-UPS and the hot-rolled HT-UPS at temperatures between 550-650°C at a strain rate of 0.001 s -1 . Extensive precipitation in the matrix after thermal aging at 600 and 650°C significantly reduced serrated plastic flow observed in the stress-strain curves, i.e. less effect of DSA. Because the DSA phenomenon can have significant influence on tensile, creep strength, and fatigue resistance, and the DSA effects in HT-UPS steels were observed in the temperature range of interest to the SFR applications, the DSA phenomenon in the HT.

Li, Meimei↗

Evolutions of the Micro- and Macrostructure and Tensile Property of Cu-15Ni-8Sn Alloy During Electromagnetic Stirring-Assisted Horizontal Continuous Casting

The present study investigates the evolution of the micro- and macrostructure and tensile property of the Cu-15Ni-8Sn (weight percent) alloy prepared by horizontal continuous casting and electromagnetic stirring (EMS). The results show that the application of EMS is beneficial for grain refinement and for microstructure transformation from the dendrite to the rosette structure and that it leads to a significant improvement in the tensile property. The forced flow induced by EMS homogenizes the temperature field ahead of the solid-liquid interface, disturbing the heat flow direction and resulting in the columnar to equiaxed transition. The grain refinement under different electromagnetic stirring frequencies is mainly derived from the homogenization of the temperature and the remelting of dendritic arms. In addition, the evolution of the tensile property with and without EMS is discussed from the perspective of fracture mode and fine-grain strengthening.

36 MATERIALS SCIENCE↗

The Effect of Boron and Zirconium on the Structure and Tensile Properties of the Cast Nickel-Based Superalloy ATI 718Plus

The effects of boron and zirconium on cast structure, hardness, and tensile properties of the nickel-based superalloy 718Plus were investigated. For this purpose, five alloys with different contents of boron and zirconium were cast via vacuum induction melting and then purified via vacuum arc remelting. Microstructural analysis by light-optical microscope and scanning electron microscope equipped with energy-dispersive x-ray spectroscopy and phase studies by x-ray diffraction analysis were performed. The results showed that boron and zirconium tend to significantly reduce dendritic arm spacing and increase the amount of Laves, Laves/gamma eutectic, and carbide phases. It was also found that boron led to the formation of B{sub 4}C and (Cr, Fe, Mo, Ni, Ti){sub 3}B{sub 2} phases and zirconium led to the formation of intermetallic phases and ZrC carbide. In the presence of boron and zirconium, the hardness and its difference between dendritic branches and inter-dendritic spaces increased by concentrating such phases as Laves in the inter-dendritic spaces. These elements had a negative effect on tensile properties of the alloy, including ductility and strength, mainly because of the increase in the Laves phase. It should be noted that the largest degradation of the tensile properties occurred in the alloys containing the maximum amount of zirconium.

36 MATERIALS SCIENCE↗

Off-axis tensile properties and fracture in a unidirectional graphite/polyimide composite (Celion 6000/PMR 15)

Tensile properties of unidirectional Celion 6000 graphite/PMR 15 polyimide composites prepared by hot molding and cold molding processes were measured at room temperature and 316 C, the upper use temperature of the polyimide resin, at both 45 and 90 deg to the fiber axis. The resulting fractures were characterized by scanning electron microscopy and materialographic techniques. Variation in tensile properties with processing history occurred in the elastic modulus and strain to failure for specimens loaded at 90 deg at 316 C, and in the fracture stress, and hence the in-plane shear stress, for those loaded at 45 deg at room temperature. Significant plastic deformation was observed in the 45 deg orientation at 316 C for material produced by both processing methods. In general, fracture occurred by both failure within the matrix and at the fiber-matrix interface; the degree of interfacial failure increased with temperature. Secondary cracking below the primary fracture surface was also observed.

Harper, J.↗

The Effect of Carboxyl Group Content on Water Uptake Capacity and Tensile Properties of Functionalized Soy Protein-Based Superabsorbent Plastics

This manuscript studies the relation between macroscopic properties of the soy protein isolate (SPI)-based superabsorbent polymers (SAP) (e.g., water uptake capacity and tensile properties) and the extent of chemical modification conducted on the protein. The increase in the carboxyl group content, obtained from electrometric titrations, for acylated systems compared to native SPI brings with it an improvement in the protein hydrophilic character, as revealed by the determination of the water imbibing capacity. SEM images show that larger porous regions were developed in the acylated plastics. As for their mechanical properties, static tensile measurements indicated that acylated plastics with greater water uptake values display higher extensibility, compared to the reference sample. These natural-based SAP materials could be appropriate for applications in which maintaining the dimensional stability during service is not crucial (e.g. in agriculture and horticulture).

36 MATERIALS SCIENCE↗

Geometric Limitation and Tensile Properties of Wire and Arc Additive Manufacturing 5A06 Aluminum Alloy Parts

Wire and arc additive manufacture (WAAM), as an emerging and promising technology of metal additive manufacturing, it lacks of experimental works to clarify the feature of geometrical configuration, microstructure and tensile properties, which can be used for further evaluating whether the as-deposited part can be used directly, and providing design reference for structure optimization. Taking 5A06 aluminum alloy additive manufacturing for example, in this paper, the geometric limitation and tensile property criteria are characterized using experimental method. The minimum angle and curvature radius that can be made by WAAM are 20° and 10 mm when the layer width is 7.2 mm. It shows isotropy when loading in build direction and perpendicular one. When loading in the direction of parallel and perpendicular to texture orientation, the tensile properties are anisotropic. The difference between them is 22 MPa.

36 MATERIALS SCIENCE↗

Dataset of tensile properties for sub-sized specimens of nuclear structural materials

Mechanical testing with sub-sized specimens plays an important role in the nuclear industry, facilitating tests in confined experimental spaces with lower irradiation levels and accelerating the qualification of new materials. The reduced size of specimens results in different material behavior at the microscale, mesoscale, and macroscale, in comparison to standard-sized specimens, which is referred to as the “specimen size effect.” Although analytical models have been proposed to correlate the properties of sub-sized specimens to standard-sized specimens, these models lack broad applicability across different materials and testing conditions. The objective of this study is to create the first large public dataset of tensile properties for sub-sized specimens used in nuclear structural materials. We performed an extensive literature review of relevant publications and extracted over 1,000 tensile testing records comprising 55 columns including material type and composition, manufacturing information, irradiation conditions, specimen dimensions, and tensile properties. The dataset can serve as a valuable resource to investigate the specimen size effect and develop computational methods to correlate the tensile properties of sub-sized specimens.

36 MATERIALS SCIENCE↗

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗

The effect of strain rate and temperature on the tensile properties of NiAl

Tensile testing of cast and extruded binary NiAl was performed from 300 to 900 K at strain rates of 0.00014 to 0.14/s. The brittle-to-ductile transition temperature (BDTT) was dependent on strain rate, with a three-order-of-magnitude increase in strain rate resulting in approximately a 200-K increase in transition temperature. Regardless of strain rate, at temperatures just above the BDTT the fracture strength increased significantly and the fracture morphology changed from mostly intergranular to predominantly transgranular. It was also determined that the mechanism responsible for the brittle-to-ductile transition in NiAl had an apparent activation energy of approximately 118 kJ/mol. These results support the argument that the mechanism for the brittle-to-ductile transition in NiAl is associated with the onset of thermally activated deformation process. This process is probably dislocation climb controlled by short circuit diffusion.

Noebe, R. D.↗

Effect of tool design and pass strategy on defect elimination and uniform, enhanced tensile properties of friction stir processed high-pressure die-cast A380 alloy

This work reports implementation of friction stir processing (FSP) to locally modify microstructure and create a defect-free processing zone with the aid of different tool designs and altering the passing strategy for two different process parameter combinations. Here, FSP is applied on high pressure die-cast (HPDC) A380 alloy, a widely used Al-Si alloy fabricated in the die casting sector for automotive and aerospace applications. However, the presence of gas and shrinkage porosity, brittle needle-shaped Fe-containing ß-FeSiAl 5 intermetallic compounds, Al-dendrites, coarse and acicular silicon particles, and large second-phase particulates have a detrimental influence on the uniformity of tensile properties across the thickness direction of an HPDC plate. FSP is able to eliminate porosity, refine microstructure and improve tensile properties. An FSP tool design and a passing strategy are identified for the best microstructure consolidation and uniform enhanced tensile properties. This study noted the importance of tool features such as scroll design and flats on tool pin and multiple pass orientation strategy to find best combination of defect-free refined microstructure and uniform tensile strength and ductility across the processing zone of HPDC Al alloys.

36 MATERIALS SCIENCE↗

Enhancing the tensile properties of EBM as-built thin parts: Effect of HIP and chemical etching

Highlights: • The EBM process leads to important cross section variations in thin parts. • Stress calculation must be based on the average section in order to be relevant. • As-built state has a detrimental effect on every mechanical property. • Mechanical properties of machined samples are met with chemical etching. • HIP has a beneficial effect on the ductility. - Abstract: As-built Ti-6Al-4 V thin parts were manufactured using Electron Beam Melting (EBM) and characterized by optical microscopy and laboratory X-ray tomography in order to observe their microstructure, pore distribution and surface aspect. Chemical etching and HIP post-treatments were applied to as-built samples and their effect on the material and static mechanical properties were studied. Tensile tests were performed on both as-built and post-treated samples and their results compared to the ones reported in the literature for machined EBM samples. Because of the significant variations of the cross section observed along the gauge length, the calculation of the tensile stresses is not straightforward. Three simple sections were measured from the tomography scans. The average section along the gauge length was considered as the most suitable. The tensile mechanical properties of the as-built samples were studied and a detrimental effect of the surface state on the yield strength, ultimate tensile strength and elongation to failure was observed. Smoothing of the surface irregularities induced by chemical etching provoked an increase of those mechanical properties whereas the change of the microstructure generated by the HIP treatment leads to a decrease of the material strength that goes along with an increase of the ductility. Down scaling factors were proposed in order to take into account the sample state, as-built or post-treated.

36 MATERIALS SCIENCE↗