Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Strain rate sensitivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Plastic deformation of single crystals of the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy in tension and compression from 10 K to 1273 K

In this report the plastic deformation behavior of single crystals of the quinary, equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy (HEA) with the face-centered cubic structure has been investigated in tension and compression as a function of crystal orientation and temperature from 10 K to 1373 K. The critical resolved shear stress (CRSS) for {111}<110> slip at room temperature is 42-45 MPa. It does not depend much on crystal orientation (i.e., the Schmid law holds true) and the sense (tension vs. compression) of the applied load. The CRSS for {111}<110> slip increases with the decrease in temperature, without showing any significant inertia effects at cryogenic temperatures below 77 K. Extrapolation from the measured yield stresses down to 10 K yields a CRSS value at 0 K of 168 MPa. At cryogenic temperatures, the measured strain-rate sensitivity of flow stress is consistent with a very small activation volume. The concept of stress equivalence holds true both for the temperature dependence of CRSS and the stress dependence of activation volume, indicating that solid-solution hardening is the major strengthening mechanism. Deformation twinning occurs at 77 K but not at room temperature, resulting in higher tensile elongation to failure at 77 K than at room temperature. Deformation twinning at 77 K occurs at a shear stress of 378 MPa on conjugate ($\bar1\bar11$) planes in the form of Lüders deformation after large plastic strain (about 85%) achieved by the stage I (easy glide) and stage II (linear work-hardening) deformation.

36 MATERIALS SCIENCE↗

Influence of strain-rate on the response of elastomeric architected materials

Architected materials have shown substantial promise in impact mitigation and protective applications, and there has accordingly been great interest in better characterizing their response at elevated strain rates due to impact. There remains ambiguity regarding the contribution of inertial and material responses to strain rate sensitivity, and, in particular, when these effects begin to gain dominance in the impact response of an architected material. The response of soft polymer architected materials as a function of strain rate, in particular, has been little investigated. We characterize the experimental impact response of four soft polymer architected lattice geometries across varying strain rates in the intermediate strain rate regime (∼10 3 s −1 ) using split-Hopkinson pressure bar loading and high speed video characterization of the resulting deformation fields. In conclusion, our results highlight the interplay of influence between constituent material, lattice geometry, length scale, and strain rate in determining the onset of significant inertia effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multi-objective automatic discovery of optimized metamaterials for varying velocity impact protection

Mechanical metamaterials have demonstrated exceptional impact performance while remaining lightweight. Impact resistance has traditionally been investigated using quasi-static simulations, often with the assumption that performance will translate to high-velocity impact scenarios. However, critical crash protection parameters—such as peak stress and absorbed energy—are highly sensitive to impact velocity, leading to inconsistent performance under dynamic loading. To address this, we introduce a strain-rate-aware, active deep learning framework that enables multi-objective optimization of impact protection metrics across a wide range of impact velocities. Our framework captures the strain-rate sensitivity of architected lattices by learning to control spatial gradation in cellular metamaterials, resulting in over 200 % enhancement in impact protection relative to state-of-the-art designs such as Voronoi and re-entrant lattices. We demonstrate its practical utility by designing next-generation lattice structures for automotive bumper systems that satisfy multiple, velocity-specific safety criteria—capabilities beyond those of conventional designs. More than just a predictive tool, this framework marks the first step towards enabling adaptable impact-resistant structures across dynamic regimes.

Deep learning↗

High-throughput quantification of quasistatic, dynamic and spall strength of materials across 10 orders of strain rates

Abstract The response of metals and their microstructures under extreme dynamic conditions can be markedly different from that under quasistatic conditions. Traditionally, high strain rates and shock stresses are achieved using cumbersome and expensive methods such as the Kolsky bar or large spall experiments. These methods are low throughput and do not facilitate high-fidelity microstructure–property linkages. In this work, we combine two powerful small-scale testing methods, custom nanoindentation, and laser-driven microflyer (LDMF) shock, to measure the dynamic and spall strength of metals. The nanoindentation system is configured to test samples from quasistatic to dynamic strain-rate regimes. The LDMF shock system can test samples through impact loading, triggering spall failure. The model material used for testing is magnesium alloys, which are lightweight, possess high-specific strengths, and have historically been challenging to design and strengthen due to their mechanical anisotropy. We adopt two distinct microstructures, solutionized (no precipitates) and peak-aged (with precipitates) to demonstrate interesting upticks in strain-rate sensitivity and evolution of dynamic strength. At high shock-loading rates, we unravel an interesting paradigm where the spall strength vs. strain rate of these materials converges, but the failure mechanisms are markedly different. Peak aging, considered to be a standard method to strengthen metallic alloys, causes catastrophic failure, faring much worse than solutionized alloys. Our high-throughput testing framework not only quantifies strength but also teases out unexplored failure mechanisms at extreme strain rates, providing valuable insights for the rapid design and improvement of materials for extreme environments.

Eswarappa Prameela, Suhas (ORCID:0000000334530184)↗

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗

Uniaxial tensile mechanical properties from a scratch on ultra-fine grained tungsten

We demonstrate that surface-based mechanical testing can be used to quantify a wide range of mechanical properties determined using traditional uniaxial tension experiments. These include mapping of dynamic stress–strain behaviour, which can be used as a screening tool for uniaxial tensile ductility (uniform elongation), fracture toughness (K C ), which is shown to be in good agreement with reported plane-strain K IC , as well work-hardening exponents (n), activation volumes (V) energies (Q) and strain-rate sensitivity (m) exponents as a function of temperature. Advantages of the surface-based approach are the ability to work with significantly smaller volumes and accommodate processing defects like pores, voids and cracks. These methods are applied to ultra-fine grained tungsten (average grain size of 650 nm), as it is an ideal candidate for alloy development efforts in advanced energy systems. Tungsten is a useful baseline as it exhibits a near-ambient temperature (approx. 200°C) ductile-to-brittle transition temperature (DBTT), enabling validation efforts for the proposed methods, and extraordinary material properties, including the highest melting temperature of any metal and complex temperature and strain-rate dependencies linked to transitions in dislocation mechanisms.

36 MATERIALS SCIENCE↗

Assessment of reverse gun taylor cylinder experimental configuration

Experimental efforts for Taylor-anvil impact tests have often been limited to near room temperature. The ‘Reverse Gun’ method proposed by Gust in 1982 allows for the Taylor impact specimen to be uniformly heated without temperature losses before impact. Through the use of finite element analysis, we explore two topics in this work. First, we examine whether the reverse gun experimental configuration is comparable to the traditional Taylor-anvil setup. Second, we assess the accuracy of several commonly employed flow strength models in terms of their ability to predict the reverse gun experimental results which involve dynamic loading conditions and complex thermo-mechanical coupling. The reverse gun simulations are performed for tantalum targets at initial temperatures in the range 295 K to 1295 K and velocities from 135 m/s to 242 m/s. We show that with suitable care in the modeling of the preheated reverse gun experiments one can make valuable assessments of flow strength models. Given the conditions explored, these observations probe the thermal softening, strain hardening, and strain rate sensitivity of the material.

42 ENGINEERING↗

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗

Boron Nitride-Driven Strengthening of Aluminum Composites via Friction Stir Processing

Friction stir welding and processing (FSW/P) has emerged as an effective solid-state joining technique for fabricating metal matrix composites (MMCs), offering improved mechanical properties through refined microstructural evolution. In this study, an aluminum-boron nitride nanoparticle (Al-BNNP) composite was synthesized via FSW, and its indentation-based mechanical properties were systematically evaluated. Microhardness mapping across the weld cross-section revealed a progressive increase in hardness toward the stir zone (SZ), attributed to severe plastic deformation, dynamic recrystallization (DRX), and the reinforcing effect of BNNPs. Profilometry-based indentation plastometry (PIP) inferred yield strength (YS) demonstrates a 47.8% increase compared to the base metal (BM) and a 75% improvement compared to FSP pure aluminum reported in literature. This enhancement is attributed to strengthening mechanisms, including grain boundary pinning, load transfer, and increased dislocation density. The strain rate sensitivity (SRS) measurements at the nanoscale demonstrated a substantial decrease in the SZ, correlated with ultrafine grain structures and strong BNNP-matrix interactions. Activation volume analysis revealed a significant reduction in the SZ, suggesting that dislocation motion is increasingly restricted by dislocation-dislocation and dislocation-particle interactions. These findings suggest that incorporating BNNPs in FSW/P enables tailoring the microstructure without thermal degradation of the secondary particles, thereby significantly enhancing the mechanical performance of aluminum composites, particularly for structural applications in aerospace and automotive industries.

Aluminum↗

Deformation mechanism in nanolaminate FeCrAl alloys by ,em>in situ micromechanical strain rate jump tests at elevated temperatures

FeCrAl alloys have attracted extensive attention as one of the potential cladding materials for the commercial light water reactors. Although the creep behaviors of coarse-grain FeCrAl alloys have been investigated at elevated temperatures, little is known on the deformation mechanism of fine-grain FeCrAl alloys. We performed surface mechanical grinding treatment to fabricate nanolaminated ferritic FeCrAl alloys. In situ micropillar compression tests were applied to determine the underlying deformation mechanism of nanolaminated FeCrAl alloys at elevated temperatures. The strain rate sensitivity and activation energy for the dominant deformation mechanism were estimated considering the presence of a threshold stress.

36 MATERIALS SCIENCE↗

Role of tilt grain boundaries on the structural integrity of WSe 2 monolayers

Transition metal dichalcogenides (TMDCs) are potential materials for future optoelectronic devices. Grain boundaries (GBs) can significantly influence the optoelectronic properties of TMDC materials. Here, we have investigated the mechanical characteristics of tungsten diselenide (WSe 2 ) monolayers and failure process with symmetric tilt GBs using ReaxFF molecular dynamics simulations. In particular, the effects of topological defects, loading rates, and temperatures are investigated. We considered nine different grain boundary structures of monolayer WSe 2 , of which six are armchair (AC) tilt structures, and the remaining three are zigzag (ZZ) tilt structures. Our results indicate that both tensile strength and fracture strain of WSe 2 with symmetric tilt GBs decrease as the temperature increases. We revealed an interfacial phase transition for high-angle GBs reduces the elastic strain energy within the interface at finite temperatures. Furthermore, brittle cracking is the dominant failure mode in the WSe 2 monolayer with tilted GBs. WSe 2 GB structures showed more strain rate sensitivity at high temperatures than at low temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗

Structure-Property Relationships of Additively Manufactured Ni-Nb Alloys [Slides]

In this work, scratch and nanoindentation testing was used to determine hardness, fracture toughness, strain rate sensitivity, and activation volumes on additively manufactured graded and uniform Ni-Nb bulk specimens. Characterization showed the presence of a two phase system consisting of Ni 3 Nb and Ni 6 Nb 7 intermetallics. Intermetallics were multimodal in nature, having grain and cell sizes spanning from a few nanometers to 10s of micrometers. The unique microstructure resulted in impressively high hardness, up to 20 GPa in the case of the compositionally graded sample. AM methods with surface deformation techniques are a useful way to rapidly probe material properties and alloy composition space.

36 MATERIALS SCIENCE↗

Model for the Softening Factor within Stages of Work Hardening

A formulation for a dimensionless coefficient c b is derived that represents a scale of microstructural softening for alloys which follow Kocks-Mecking (K-M) work hardening behavior. The variation of the true plastic strain ε p between the proportional limit σ y and the strength σ u at the instability is determined using the Considère criterion. Parameterization of the model is limited to variables expressly measured within tensile experiments. Further development is now made for the softening factor c bi through the individual and sequential stages 3 and 4 of plastic deformation during K-M work hardening Q behavior. Application is shown for tensile test results of Ti-6Al-4V made by different additively manufactured (AM) processes. It is found that the variation in plastic strain as a function of c bi produces a continuous curve representative of the alloy system. The results of data analysis indicate that Θ o3 and c b3 increase, while Θ o4 and c b4 decrease, as the total plastic strain ε p increases. Furthermore, formulations derived for K-M stages 3 and 4 enable the evaluation of other material parameters such as the activation volume ν* for the onset of plastic deformation. This activation volume is found to be near constant, at a ν*-value of 0.353±0.036 nm 3 as computed using a strain-rate sensitivity of strength exponent m of 0.014, irrespective of the AM method used to produce the Ti-6Al-4V alloy.

36 MATERIALS SCIENCE↗

Copper-Tantalum Metal Matrix Composites Consolidated from Powder Blends by Severe Plastic Deformation

We investigated the effectiveness of severe plastic deformation by equal channel angular extrusion (ECAE) for consolidation of metal powders into metal matrix composites. Equal volumes of copper (Cu) and tantalum (Ta) powders were consolidated at ambient temperature via different ECAE routes. Composites processed by ECAE routes 4E and 4Bc were also processed at 300 °C. The resulting materials were characterized by scanning electron microscopy (SEM) and compression testing. Processing by route 4Bc at 300 °C resulted in the highest compressive strength, lowest anisotropy, and least strain rate sensitivity. We conclude that the superior properties achieved by this route arise from mechanical bonding due to interlocking Cu and Ta phases as well as enhanced metallurgical bonds from contact of pristine metal surfaces when the material is sheared along orthogonal planes.

36 MATERIALS SCIENCE↗

Strain rate effects on the mechanical behavior of porous titanium with different pore sizes

High strain-rate (up to 6600 s –1 ) and quasi-static compression tests are conducted on a powder-sintered porous titanium with different pore sizes (mean: 30 μm and 120 μm). In situ X-ray imaging is implemented to characterize the pores-scale deformation dynamics. The yield strength as a function of strain rate exhibits two stages of rate sensitivity, and the transition occurs at 1600 s –1 . X-ray images show that pore compaction and strain localizations occur preferentially at pores oriented perpendicular to the loading direction under quasi-static loading, but become more random under high strain-rate loading as a result of higher driving force and plastic deformation nucleation rate. Here, the more homogeneous nucleation of plastic deformation contributes to the increased rate sensitivity beyond 1600 s –1 . At the same strain rate, the yield strength of porous Ti as well as strain field homogeneity decreases significantly with increasing pore size. The small pore spacing in fine-pored Ti reduces the degree of stress concentrations around pores. Therefore, the higher stress concentrations in coarse-pored Ti lead to an earlier yield of matrix around pores and thus a lower bulk yield strength.

36 MATERIALS SCIENCE↗