SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Si nanowire electrodes have great potential as high-capacity anodes for Li-ion batteries. This review provides a comprehensive evaluation of the Li-storage capacity of various Si nanowire electrodes based on both specific and areal capacity.
Technique increases the signal current, where direct beam readout is used, in Secondary Electron Conduction /SEC/ camera tubes. Increasing the storage capacity and therefore the dynamic range of the SEC target permits satisfactory operation at reduced frame rates.
Here, scanning transmission X-ray microscopy (STXM) analysis was utilized to directly present visual evidence of changes in oxygen storage capacity (OSC) when small amounts of an additive were incorporated into CeO2. Specifically, the chemical map measured by STXM analysis differentiated between Cu-rich and Ce-rich areas to derive the proportion of Ce3+. Additionally, we found that the dispersion of Cu significantly influenced the formation of OSC. The findings were applied to the high-temperature water–gas shift reaction for producing high-purity hydrogen from waste-derived syngas, establishing a correlation with catalyst performance. Consequently, the CCM75 (Ce/Mg = 75/25) catalyst demonstrated the highest Cu dispersion and OSC values (6.9 %, 800.3 μmolO/gcat), and it also showed the highest CO conversion (79 % at 450 °C) and stability (−7.7 % at 450 °C after 50 h), attributed to the significant presence of active Cu. This study confirms previously reported interactions between Cu and CeO2 and uncovers the significant roles of Cu and Mg in this catalysis system, providing new understanding of the mechanisms that facilitate OSC improvement.
Copper exchanged chabazites are among the state-of-the-art catalyst materials being studied for selective catalytic reduction of NOx, however, there is still a need to understand how these materials store ammonia after aging. In this work, studies are performed to assess the ammonia storage capacity of Cu-SSZ-13 as a function of concentration, temperature, and extent of hydrothermal aging. Ammonia binds at three difference sites: (i) a Cu site bound at 1 framework Al (Z 1 Cu site), (ii) a Cu site bound at 2 framework Al (Z 2 Cu site), and (iii) a Brønsted acid site (ZH site). Results show that a 3-site model can accurately capture ammonia storage across all conditions. Impacts for hydrothermal aging are considered via 3 aging reactions that change the site densities of each identified adsorption site. Model assessment shows that during aging there is a significant loss in Brønsted acid sites.
Assuring secure containment of stored CO 2 is of paramount importance—for climate change mitigation, for permitting, and for reassuring the public. Regional seals, such as those sealing petroleum accumulations, have proven to be effective for securing CO 2 . However, the goal of permanent sequestration can also be satisfied with “composite confining systems” consisting of multiple, possibly discontinuous flow barriers that, in aggregate, create a system with very high permeability anisotropy and effectively retard the vertical migration of CO 2 . This study focuses on investigating the barrier characteristics necessary for effective containment of CO 2 , using both physical flow experiments and modified invasion percolation simulations. The simulations are calibrated to the physical experiments and are used to further extend the analysis. Results show that for a composite confining system, a) even barriers with low capillary entry pressure contrast to the underlying flow unit can divert rising CO 2 ; b) curved or anticlinal barrier topography can enhance CO 2 trapping; c) fining-upward gradations make little difference to barrier effectiveness or CO 2 retention; d) longer barriers retain more CO 2 regardless of barrier topography. Finally, field-scale simulations have demonstrated the importance of barrier length for increasing CO 2 storage capacity. Furthermore, the results presented can be used to inform the development of new screening criteria for characterization and effectiveness of composite confining systems.
Metal–organic frameworks (MOFs) are promising, tunable materials for hydrogen storage. For application under cryogenic operating conditions, past work has run into a ceiling on performance due to a trade-off in the volumetric deliverable capacity (VDC) versus the gravimetric deliverable capacity (GDC). In this study, we computationally constructed and screened 105 230 MOF structures based on 529 nets to explore the effect of underlying topology on the hydrogen storage performance of the resulting materials. A machine learning model was developed based on simulated hydrogen uptake to facilitate screening of the entire dataset, and it successfully identified the top 10% of materials with a root-mean-square error of approximately 1 g L −1 as validated by subsequent grand canonical Monte Carlo simulations. We identified a promising structure based on the tsx topology that exhibits both VDC and GDC higher than the current benchmark material, MOF-5. Our data-driven analysis indicates that nets with higher net density yield MOFs with enhanced volumetric and gravimetric surface areas, thereby improving maximum VDC while shifting the capacity trade-off toward higher GDC.
The abundance and diversity of hydrogen applications necessitates continued and accelerated research into advanced storage technologies. Traditionally, hydrogen has been stored as either a high-pressure, warm gas; or a low-pressure, cryogenic liquid. Methods such as cryo-supercritical and cryo-adsorbed have been explored, but are not yet mainstream. Cryo-adsorbed is attractive because higher storage densities at higher temperatures than liquid may be achieved. Recently NASA, in partnership with Eta Space, Southwest Research Institute, the University of Central Florida, and Air Liquide, have been exploring the use of inexpensive, commercially available silica aerogel blanket materials for cryo-adsorbed hydrogen storage. Unlike most adsorbents, aerogel blanket is not a powder, but a robust, composite material that can be formed into complex shapes to aid in more efficient storage system designs, and has already been proven to uptake large quantities of fluids such as nitrogen and oxygen. Recent experimental efforts into the uptake of low-pressure hydrogen gas at 77 K, and liquid hydrogen at normal boiling point (NBP) will be discussed. Although preliminary in nature, the test results are promising, showing up to a 49% increase in storage density at 77 K over the gas alone, and greater than a one-to-one volume equivalency with NBP LH 2 .
The use of epoxy resin fiber glass and economic factors affecting the choice of materials for gas storage are discussed. The physical nature of the filament windings are described together with the results obtained. It is demonstrated that a substantial reduction in mass and an enhanced level of safety can be assured at a competitive cost by storing gases in this way.
Not Available
Not Available
Aqueous Zn-ion batteries (AZIBs) are promising alternatives to lithium-ion batteries in stationary storage. However, limited storage capacity and cyclic life impede their large-scale implementation. In this study, we report reversible electrochemical insertion of multi-ions into sodium vanadate (NaV 3 O 8 ) cathode materials for AZIBs, achieving a maximum storage capacity of 450 mAh g –1 at 0.05 A g –1 and a capacity retention of 82% after 500 cycles at 0.4 A g –1 . In addition to Zn 2+ and H + insertion, in situ X-ray diffraction (XRD) and X-ray absorption spectroscopy (XAS) collectively provide explicit evidence on vanadyl ions (VO 2+ ) conversion–intercalation at the NaV 3 O 8 cathode, showing the deintercalation of VO 2+ from NaV 3 O 8 and the consequent conversion of VO 2+ into V 2 O 5 on charging, and vice versa on discharging. Our study is the first to report on the cation conversion–intercalation mechanism in AZIBs. This reversible multi-ion storage mechanism provides a design principle for developing high-capacity aqueous electrode materials by engaging both the intercalation and conversion of charge carriers.
An engine and cabin thermal management system for use with a vehicle having an engine, a cabin heating system configured to thermally heat a cabin of the vehicle, a coolant system operably coupled to the engine and to the cabin heating system to thermally manage a temperature of the engine and a temperature of the cabin. The coolant system having one or more coolant thermal storage units fluidly coupled with a radiator and heater core of the coolant system forming a coolant loop. The system further having a control system configured to monitor and maintain at least a predetermined coolant temperature at the cabin heating system even during a coolant temperature decrease at the engine stops.
Adopting a solid-phase microwave-assisted technique followed by thermal pyrolysis of N-functionalized graphene quantum dots, novel nitrogen-doped graphite-like (NGL) electrode materials were synthesized in this work and served as the anode for Li-ion batteries. The NGL anode demonstrated reversible capacity of 530 mAh g -1 at 0.1C, superior rate capability at high C rate operation (420 mAh g -1 at 5C), remarkable initial coulombic efficiency (>95.7%), and excellent cyclic stability along with high efficiency (>99.1%) during entire cycling. The NGL anode nanostructure enables improved lithium ion mobility and reversible Li + storage during cycling. The analysis of the Ragone plots revealed that the specific energy of NGL anode reaches to ca. 840 Wh kg -1 at the power density of 4200 W kg -1 . The diffusion coefficient of Li ions was measured as 1.69 × 10 -9 cm 2 s -1 for the NGL anode material, substantially improving over commonly used graphite electrodes (15–26 times higher Li + diffusivity). The high-rate cyclability as well as the cyclic stability of the NGL anodes were also confirmed via long-term cycling of full pouch cells assembled with ternary cathode and NGL anode. The robust design of the NGL anode materials introduced in this work, paves the way for designing next-generation lithium-ion batteries operating at ultra-high C rates.
Oil/water microemulsions (µEs) are promising electrolytes for redox flow batteries (RFBs) as they simultaneously improve charge capacity and ionic conductivity. Here, we report the successful formulation of bicontinuous µEs where the oil phase is a solution of trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)amide ionic liquid in toluene with redox-active ferrocene. We examined the effect of supporting electrolyte anion (NO 3 – , Cl – , ClO 4 – ) on the structure, reactivity, transport, and electrolytic performance of redox-active µEs. Neutron scattering and nuclear magnetic resonance showed that the domain size increased as Cl – > NO 3 – > ClO 4 – while the ferrocene diffusion coefficient increased as NO 3 – > Cl – > ClO 4 – . Scanning electrochemical microscopy indicated anion-dependent current fluctuations during electrolysis, with ClO 4 – exhibiting the least high-frequency oscillations, which correlate to the highest charge and discharge capacity and reversibility. All ionic liquid containing systems improved the performance of toluene-based µEs, highlighting new design principles for these electrolytes.
Not provided.
Not Available