Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Stamping”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Manufacturing Water‐Based Low‐Tortuosity Electrodes for Fast‐Charge through Pattern Integrated Stamping

Achieving high energy density and fast charging of lithium‐ion batteries can accelerate the promotion of electric vehicles. However, the increased mass loading causes poor charge transfer, impedes the electrochemical reaction kinetics, and limits the battery charging rate. Herein, this work demonstrated a novel pattern integrated stamping process for creating channels in the electrode, which benefits ion transport and increases the rate performance of the electrode. Meanwhile, the pressure applied during the stamping process improved the contact between electrode and current collector and also enhanced the mechanical stability of the electrode. Compared to the conventional bar‐coated electrode with the same thickness of 155 μm (delivered a discharge capacity of 16 mAh g −1 at the rate of 3 C), the stamped low‐tortuosity LiFePO 4 electrode delivered 101 mAh g −1 capacity. Additionally, water was employed as a solvent in this study. Owing to its eco‐friendliness, high scalability, and minimal waste generation, this novel stamping technique inspire a new method for the industrial‐level efficient roll to roll fabrication of fast‐charge electrodes.

25 ENERGY STORAGE↗

Pre-Oxidized and Nitrided Stainless Steel Foil for Proton Exchange Membrane Fuel Cell Bipolar Plates: Part 2- Single-Cell Fuel Cell Evaluation of Stamped Plates

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {approx}5-20% better peak power output than untreated Fe-20Cr-4V, 2205, and 904L metal stampings. Durability was assessed for pre-oxidized/nitrided Fe-20Cr-4V, 904L metal, and graphite plates by 1000+ h of cyclic single-cell fuel cell testing. All three materials showed good durability with no significant degradation in cell power output. Post-test analysis indicated no metal ion contamination of the membrane electrode assemblies (MEAs) occurred with the pre-oxidized and nitrided Fe-20Cr-4V or graphite plates, and only a minor amount of contamination with the 904L plates.

30 DIRECT ENERGY CONVERSION↗

Facile stamp patterning method for superhydrophilic/superhydrophobic surfaces

Patterning techniques are essential to many research fields such as chemistry, biology, medicine, and micro-electromechanical systems. In this letter, we report a simple, fast, and low-cost superhydrophobic patterning method using a superhydrophilic template. The technique is based on the contact stamping of the surface during hydrophobic dip coating. Surface characteristics were measured using scanning electron microscopy and energy-dispersive X-ray spectroscopic analysis. The results showed that the hydrophilic template, which was contacted with the stamp, was not affected by the hydrophobic solution. The resolution study was conducted using a stripe shaped stamp. The patterned line was linearly proportional to the width of the stamp line with a constant narrowing effect. A surface with regions of four different types of wetting was fabricated to demonstrate the patterning performance.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Large Scale Metal Additive Manufacturing for Stamping Dies

Oak Ridge National Laboratory (ORNL) worked with Dienamic Tooling Systems (DTS) in a follow-on Phase 2 effort to develop and demonstrate additively manufactured conformal cooling for hot stamping dies, providing a new industry capability that did not previously exist. Current approaches to die cooling are nonoptimal and based on what can be machined with traditional technologies. The printed approach to hot stamping cooling channels allows an analytical needs-based size and placement approach to cooling. Cooling is optimized and parts count is reduced producing a simpler more reliable faster to manufacture stamping tool. An additively manufactured hot stamping die with conformal cooling channels was manufactured and successfully tested in a real-world environment.

36 MATERIALS SCIENCE↗

Automated Calculation of Bulk-Stamping Matrices for Circular Blanks

The bulk stamping of circular blanks is considered. There is a clear need for automatic stamping. The input and output data for calculating the working part of the bulk-stamping matrix are analyzed. Software for automated calculation of bulk-stamping matrices is developed. The program code and a possible interface for the calculation of matrix parameters and construction of 3D models by means of the Object Pascal language are presented.

42 ENGINEERING↗

A cracked beam or plate transversely loaded by a stamp

In this paper the problem of an infinite elastic beam or a plate containing a crack is considered. The medium is loaded transversely through a stamp which may be rigid or elastic. The problem is a coupled crack-contact problem which cannot be solved by treating the crack and contact problems separately and by using a superposition technique. First the Green's functions for the general case are obtained. Then the integral equations for a cracked infinite strip loaded by a frictionless stamp are obtained. With the question of fracture in mind, the primary interest in the paper has been in calculating the stress intensity factors. The results are given for a rigid flat stamp with sharp edges and for an elastic curved stamp. The effect of friction at the supports on the stress intensity factors is also studied and a numerical example is given.

Nied, H. F.↗

Using GPS Receiver 1PPS Output to Verify Time Stamp Accuracy and Measure Propagation Delay

A simple pulse overlay circuit using a logic OR gate was developed to overlay a precise leading edge 1 pulse per second time reference marker from a global positioning system receiver onto a non-return -to- zero-level pulse code modulation telemetry data stream to validate time stamp accuracy and measure propagation delay in telemetry equipment. A pulse overlay (PO) circuit was designed to produce a time reference marker within a pulse code modulation (PCM) telemetry data stream that was recorded and analyzed to validate an IRIG Standard 106-17 Chapter 10 recorder’s time stamp accuracy [1]. A manufacturer of a newly purchased Chapter 10 recorder claimed the time stamp accuracy to be better than 10 microseconds (μs) with only IRIG-B120 (IRIG-B) input and better than 1 μs with IRIG-B and one pulse per second (1PPS) inputs. The PO circuit and a Chapter 10 recorder test setup were used to verify the vendor’s data-time synchronization claims and to justify infrastructure upgrade costs to connect additional cables to each purchased recorder. The circuit was also used to measure the propagation delay (PD) of a long distance Telemetry multiplexer/demultiplexer telecommunication system which the manufacturer did not provide a PD specification. Using the one pulse per second time reference marker of the global positioning system receiver and the pulse overlay circuit to overlay the one pulse per second variable pulse width signal into a pulse code modulation telemetry stream provided an excellent means to validate time stamp accuracy within a Chapter 10 recorder and to measure propagation delays within a normal telemetry operating environment. The positive results from the Chapter 10 recorder tests validated the vendor’s claims and justified the implementation to add the one pulse per second signal to the range Chapter 10 recorders. The pulse overlay circuit and test setups defined in this paper can easily be used to measure other telemetry equipment.

Knudtson, Kevin↗

Validation of Manufacturing Process Designs for Stamped Microchannel Recuperators

Microchannel recuperators can achieve high-efficiency power cycles and chemical reactions by recovering waste heat from hot turbine exhaust and chemical reaction streams. However, the industrial application of microchannel recuperators are restricted by the high cost of patterning and bonding. The objective of this study was thus to investigate new methods for producing microchannel recuperators for emerging markets. Based on greenfield cost estimates, process designs based on stamping, laser welding and vacuum brazing of 316L stainless steel laminae were found to be more economical than conventional photochemical machining and diffusion bonding. Subsequently, validation experiments were conducted to produce stamped microchannel components using cost model parameters. At a mass flow rate of 0.99 g/s, the test article made with laser welding was found to provide higher effectiveness than the test article produced using vacuum brazing. Preliminary investigations showed that residual stresses during laser welding of the laminae led to significant warpage, collapsing channels and making lamina-to-lamina fit up challenging. In contrast, the test article produced by vacuum brazing of stamped laminae showed no clogging and 4.6% and 10.5% channel height standard deviation for the cold and hot channels, respectively. Channel variation in the vacuum brazing sample was determined to be caused by misregistration of laminae during brazing. In future work, efforts are needed to choose cheaper, more ductile brazing foils as well as design a brazing fixture to improve lamina-to-lamina registration.

42 ENGINEERING↗

Stamping Nanoparticles onto the Electrode for Rapid Electrochemical Analysis in Microfluidics

Electrochemical analysis is an efficient way to study various materials. However, nanoparticles are challenging due to the difficulty in fabricating a uniform electrode containing nanoparticles. We developed novel approaches to incorporate nanoparticles as a working electrode (WE) in a three-electrode microfluidic electrochemical cell. Specifically, conductive epoxy was used as a medium for direct application of nanoparticles onto the electrode surface. Three approaches in this work were illustrated, including sequence stamping, mix stamping, and droplet stamping. Shadow masking was used to form the conductive structure in the WE surface on a thin silicon nitride (SiN) membrane. Two types of nanomaterials, namely cerium oxide (CeO2) and graphite, were chosen as representative nanoparticles. The as-fabricated electrodes with attached particles were characterized using atomic force microscopy (AFM) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Electrochemical analysis was performed to verify the feasibility of these nanoparticles as electrodes. Nanomaterials can be quickly assessed for their electrochemical properties using these new electrode fabrication methods in a microfluidic cell, offering a passport for rapid nanomaterial electrochemical analysis in the future.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Design, performance, and cost savings of using GF-PC additively manufactured tooling for stamping of HSS 590 sheet metal

Conventional sheet metal forming tooling in the automotive industry is made up of hardened steel and used for mass-production. Prototype tooling made of metal is durable, but it is only used for a small number of parts despite its high cost, contributing heavily to the vehicle development cost. Additive Manufacturing (AM) offers a low-cost alternative for fabricating tooling suitable for low-volume production. Here, this study investigates the feasibility of using AM polymer composite tooling for the stamping of 1.5mm thickness HSS 590 steel sheets through a two-pronged approach – experimental and numerical analysis. Sheet metal stamping experiments were conducted with glass fiber reinforced polycarbonate (GF-PC) AM polymer tooling and their performance was evaluated based on various metrics such as tool deformation and part accuracy. Finite element simulations of the stamping process were performed, which accurately captured the tool deformations seen in experiments with the use of anisotropic material models. The effective use of simulations in optimizing process parameters to achieve the desired final part geometry is also demonstrated. The GF-PC AM polymer composite tooling was found to be well suited for low volume production applications with potential cost savings.

36 MATERIALS SCIENCE↗

Martensitic microstructural transformations from the hot stamping, quenching and partitioning process

Hot stamping, which combines forming and quenching in one process, produces high strength steels with limited ductility because the quenching is uncontrolled. A new processing technique has been proposed in which the hot stamping step is followed by a controlled quenching and partitioning process, producing a microstructure containing retained austenite and martensite. To investigate this microstructure, specimens were heated at a rate of 10 deg. C/s to the austenitizing temperature of 900 deg. C, held for 5 min to eliminate thermal gradients, and cooled at a rate of 50 deg. C/s to a quenching temperature of 300 deg. C, which is between the martensite start temperature and the martensite finish temperatures. The resulting microstructure was examined using optical microscope, scanning electron microscopy and transmission electron microscopy. The material produced contains irregular, fragmented martensite plates, a result of the improved strength of the austenite phase and the constraints imposed by a high dislocation density. - Research Highlights: {yields} A novel heat treatment of advanced high strength steels is proposed. {yields} The processing technique is hot stamping plus quenching and partitioning process. {yields} The material produced contains irregular, fragmented martensite plates. {yields} The reason is strength of austenite phase and constraint of dislocation density.

36 MATERIALS SCIENCE↗

Three-Dimensional Patterning of Nanoparticles by Molecular Stamping

Directing the formation of nanoscale architectures from nanoparticles is one of the key challenges in designing nanomaterials with prescribed functions. Atomic systems, given their ability to form molecules and crystals via directional chemical bonds, provide an inspiration for establishing approaches where nanoparticles with designed anisotropic binding modalities can be assembled into nanoscale architectures. However, fabricating such nanoparticles has been challenging due to their small dimensions and limited ways for site-specific control of their surface. To this end, we present a Molecular Stamping (MOST) approach to pattern DNA-coated nanoparticles with molecules at the predefined positions on a nanoparticle surface. This patterning is realized by use of a rigid and coordinative DNA frame as a molecular stamping apparatus (MOST App). The MOST App transfers multiple types of molecular “inks”, DNA sequences, onto nanoparticle surface and fixes these molecular inks into place to form a designed pattern. After a nanoparticle release from MOST App, it possesses single-molecule patches that can provide anisotropic bonds with distinctive affinities. We further use these stamped nanoparticles to assemble prescribed clusters, whose structure is determined by the locations of patches. Using electron microscopy and tomographic methods, we investigate the efficiency of cluster formation and the resulting spatial arrangements of nanoparticles. The presented approach provides a single-molecule and spatiallydetermined control over nanoparticle functionalization for creating nanoparticles with designed placement of different molecules and for realizing a rational fabrication of nanomaterial architectures.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation of the Phase Formation of AlSi-Coatings for Hot Stamping of Boron Alloyed Steel

Hot stamping of boron alloyed steel is gaining more and more importance for the production of high strength automotive body parts. Within hot stamping of quenchenable steels the blank is heated up to austenitization temperature, transferred to the tool, formed rapidly and quenched in the cooled tool. To avoid scale formation during the heating process of the blank, the sheet metal can be coated with an aluminium-silicum alloy. The meltimg temperature of this coating is below the austenitization temperature of the base material. This means, that a diffusion process between base material and coating has to take place during heating, leading to a higher melting temperature of the coating.In conventional heating devices, like roller hearth furnaces, the diffusion process is reached by relatively low heating rates. New technologies, like induction heating, reach very high heating rates and offer great potentials for the application in hot stamping. Till now it is not proofed, that this technology can be used with aluminum-silicon coated materials. This paper will present the results of comparative heating tests with a conventional furnace and an induction heating device. For different time/temperature-conditions the phase formation within the coating will be described.

36 MATERIALS SCIENCE↗

Numerical Simulation of Textile Composite Stamping On Double Dome

Stamping is one of the most effective ways to form textile composites in industry for providing high-strength, low-weight and cost-effective products. This paper presents a fully continuum mechanics-based approach for stamping simulation of textile fiber reinforced composites by using finite element (FE) method. A previously developed non-orthogonal constitutive model is used to represent the anisotropic mechanical behavior of textile composites under large deformation during stamping. Simulation are performed on a balanced plain weave composite with 0 deg./90 deg. and {+-}45 deg. as initial yarn orientation over a benchmark double dome device. Simulation results show good agreement with experimental output in terms of a number of parameters selected for comparison.

36 MATERIALS SCIENCE↗

Numerical simulation of temperature field, microstructure evolution and mechanical properties of HSS during hot stamping

The hot stamping of boron steels is widely used to produce ultra high strength automobile components without any spring back. The ultra high strength of final products is attributed to the fully martensitic microstructure that is obtained through the simultaneous forming and quenching of the hot blanks after austenization. In the present study, a mathematical model incorporating both heat transfer and the transformation of austenite is presented. A FORTRAN program based on finite element technique has been developed which permits the temperature distribution and microstructure evolution of high strength steel during hot stamping process. Two empirical diffusion-dependent transformation models under isothermal conditions were employed respectively, and the prediction capability on mechanical properties of the models were compared with the hot stamping experiment of an automobile B-pillar part.

36 MATERIALS SCIENCE↗

Time-stamped claim logic

Abstract The main objective of this paper is to define a logic for reasoning about distributed time-stamped claims. Such a logic is interesting for theoretical reasons, i.e. as a logic per se, but also because it has a number of practical applications, in particular when one needs to reason about a huge amount of pieces of evidence collected from different sources, where some of the pieces of evidence may be contradictory and some sources are considered to be more trustworthy than others. We introduce the time-stamped claim logic including a sound and complete sequent calculus. In order to show how time-stamped claim logic can be used in practice, we consider a concrete cyber-attribution case study.

Rasga, João↗

Development of Surface Treatment Solutions for Stamping Tools Fabricated via Additive Manufacturing

Oak Ridge National Laboratory (ORNL) and H.E.F. USA, Inc. (HEF) partnered to develop wear resistant surface treatment of additive manufactured steels for stamping die applications under CRADA agreement NFE-19-07909. This project aimed at evaluating the ARCOR® process, developed by HEF, to improve the surface behavior of 410SS (stainless steel), 410NiMo SS, 630 SS, and Maraging 250 steel coupons and demo components, fabricated via wire arc additive manufacturing (WAAM), with and without post print heat treatment. The peak hardness achieved was ~1000 HV and above (Up to 1300 HV) for all materials under proper processing parameters, and far exceeded the target hardness of 746 HV (60 HRC). Finally, stamping tools were printed and nitrocarburized with the optimum parameters, and then went through 500 fabrication cycles. Characterization of the used 17-4PH stamping tool discovered no crack or delamination in the nitrocarburized layer and the interface between the nitrocarburized layer and substrate.

36 MATERIALS SCIENCE↗

Integrated software package STAMP for minor planets

The integrated software package STAMP allowed for rapid and exact reproduction of the tables of the year-book 'Ephemerides of Minor Planets.' Additionally, STAMP solved the typical problems connected with the use of the year-book. STAMP is described. The year-book 'Ephemerides of Minor Planets' (EMP) is a publication used in many astronomical institutions around the world. It contains all the necessary information on the orbits of the numbered minor planets. Also, the astronomical coordinates are provided for each planet during its suitable observation period.

Kochetova, O. M.↗