Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Influence of Solidification Velocity on Partitioning and Precipitate Evolution in a Multicomponent, Soft Magnetic Alloy Processed by Laser Melting

Multicomponent alloys have recently been shown to overcome the structural-functional barrier associated with soft magnetic materials. Here, single laser tracks have been used to investigate the effects of solidification velocity on the Al 7 Fe 32.6 Co 27.7 Ni 27.7 Ta 5 (at pct) alloy. Ta-rich cell wall partitioning was shown to affect the final distribution and size of the precipitating L1 2 phase, after aging. These findings demonstrate that solidification rate control offers the potential to tailor localized performance in alloys with size-dependent precipitation properties.

Brookins, Jeffrey M. [Oak Ridge National Laborator↗
DOE OSTI2025

In-Situ Synchrotron X-Ray Diffraction of Ultrasonic Microstructural Refinement During Solidification in a Commercial Al–Si–Mg Alloy

This study reports the first use of in-situ synchrotron X-ray diffraction (SXRD) to study the effects of ultrasonic melt processing (USMP) on phase and grain size evolution during solidification in a commercial Al–Si–Mg casting alloy. USMP is a technique that, when applied to aluminum as it solidifies, can be used to refine the local microstructure of large-scale castings. Analysis of the in-situ SXRD data to estimate the average grain size of primary α-Al grains during USMP demonstrates that USMP slows the growth rate of α-Al grains and reduces grain size by 36 pct. Furthermore, there is also evidence that USMP causes the primary α-Al grains to move relative to the X-ray beam; such motion increases the probability of primary α-Al grains colliding and fragmenting. This movement becomes constrained at the onset of the Al–Si binary eutectic, suggesting that USMP ceases to effectively refine the microstructure once the Al–Si binary eutectic begins to form. Complementary laboratory-scale X-ray diffraction (XRD) data were used to correlate the lattice parameters of the α-Al and Si (D-A4) phases with temperature to estimate cooling rate during solidification. Thus, this study can guide the design of novel castings with spatially distributed fine-grained regions produced using local ultrasonic processing.

Aluminum Alloys↗
DOE OSTI2026

Solidification cracking of refractory alloys: a computational and machine learning study to investigate composition-dependence for improved weldability and additive manufacturability

Large-batch numerical, CALculation of PHAse Diagrams (CALPHAD)-based solidification cracking calculations are performed and then analyzed with machine learning methods to generate models that relate chemistry of refractory alloys to cracking susceptibility. Kou’s solidification cracking index is used to study the refractory alloys including O, N, C binary mixtures with Mo, Ta, Nb, and W, the molybdenum-based TZM, Niobium-based C103, and Tantalum-based T111 and Ta-10 W, as well as hypothetical refractory ternary alloys. Findings strongly validate Kou’s Crack Susceptibility Index (CSI) against Varestraint test data for Nb- and Ta-based alloys, establishing CSI thresholds where refractory alloys with CSI < 15,000 K are likely weldable, CSI > 15,000 K are prone to cracking, and CSI > 25,000 K are likely unweldable (or unprintable). Furthermore, interstitial elements C, N, and O significantly increase crack susceptibility, with some existing material specifications coinciding with peak cracking susceptibility concentrations. Finally, machine learning-derived elemental potency factors enable rapid prediction of CSI from alloy chemistry for C103, TZM, Ta-10 W, and T-111 alloys. These results provide practical guidance for feedstock selection, powder reuse limits, and alloy specification amendments for welding and additive manufacturing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Irradiation of an enriched uranium (NaCl-UCl 3 ) fuel salt capsule, summary of nondestructive post-irradiation examinations, and solidification modeling

Molten salt reactors (MSRs) are gaining attention due to their potential for safe, carbon-free nuclear energy with reduced waste. However, licensing these reactors is hindered by limited experimental data on fueled salts, both pre- and post-irradiation. Here, the novel Molten-salt Research Temperature-controlled Irradiation (MRTI) vehicle was designed to address knowledge gaps in irradiating enriched‑uranium-bearing salts. The MRTI experiment irradiated 13 cm 3 of UCl₃-NaCl (93 % U-235) salt in the Neutron Radiography (NRAD) Reactor, achieving a burnup of 0.196 GWd/MTU over 390 h. Despite a heater failure, the thermocouple data suggested fission heat kept the salt molten. The MRTI assembly was remotely disassembled for nondestructive post-irradiation examination (PIE), which included precision gamma-ray scanning (PGS) and neutron radiography. Radiograph images showed the location of the salt and the solidification pattern. PGS results provided an early indication that activated materials of construction did not increase in relative intensity in the region of the capsule where the salt was in contact with the material of construction. Additionally, PGS data showed the presence of several gamma emitting fission products, such as Nb-95, Zr-95, Ru-103, Ce-141, and La-140, where Ru-103 had the highest counts at the bottom of the capsule. Computational fluid dynamics modeling supported observations of salt solidification patterns and proved to be a valuable tool to inform PIE activities. The MRTI experiment has thus far provided critical data and lessons learned for fuel salt PIE activities, essential for advancing the technical readiness of MSRs.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Quantification and prediction of solidification textures under additive manufacturing conditions

Crystallographic textures are a major determinant of the macroscale anisotropic properties of polycrystalline metallic alloys produced in a wide range of additive manufacturing (AM) processes. Here, we introduce a statistical method that can accurately quantify the degree of orientational order of textures despite the large random fluctuations in the orientation of individual grains inherent in AM processes. The method, demonstrated for laser and resolidification of AlSi thin films, extends Z-scoring to a dynamical regime to assess the statistical significance of observed textures compared to randomly generated ones at different stages of solidification. We further show that, combined with phase-field modeling, this method can be used to infer fundamental anisotropic properties of the solid-liquid interface that are essential for texture prediction, and are compared here to the results of atomistic simulations. In addition, phase-field modeling reveals that, even at rapid AM solidification rates, the observed 〈110〉-dominated textures in the AlSi thin films are controlled predominantly by the anisotropy of the interface free-energy and sheds light on the physical mechanism of grain competition. These results significantly enhance both the existing tools for the quantification and prediction of AM crystallographic textures and our basic understanding of their formation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Highly Ordered Eutectic Mesostructures via Template‐Directed Solidification within Thermally Engineered Templates

Template-directed self-assembly of solidifying eutectics results in emergence of unique microstructures due to diffusion constraints and thermal gradients imposed by the template. Here, the importance of selecting the template material based on its conductivity to control heat transfer between the template and the solidifying eutectic, and thus the thermal gradients near the solidification front, is demonstrated. Simulations elucidate the relationship between the thermal properties of the eutectic and template and the resultant microstructure. The overarching finding is that templates with low thermal conductivities are generally advantageous for forming highly organized microstructures. When electrochemically porosified silicon pillars (thermal conductivity < 0.3 Wm −1 K −1 ) are used as the template into which an AgCl-KCl eutectic is solidified, 99% of the unit cells in the solidified structure exhibit the same pattern. In contrast, when higher thermal conductivity crystalline silicon pillars (≈100 Wm −1 K −1 ) are utilized, the expected pattern is only present in 50% of the unit cells. The thermally engineered template results in mesostructures with tunable optical properties and reflectances nearly identical to the simulated reflectances of perfect structures, indicating highly ordered patterns are formed over large areas. This work highlights the importance of controlling heat flows in template-directed self-assembly of eutectics.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Benchmark microgravity experiments and computations for 3D dendritic-array stability in directional solidification

In this study, we present a comprehensive quantitative analysis of stability bands for dendritic arrays during directional solidification of a transparent succinonitrile-0.46 wt % camphor alloy, spanning a broad range of pulling velocities. Taking advantage of the microgravity environment aboard the International Space Station where most convection effects are suppressed, we obtain unique measurements that quantify the stable primary spacing range of spatially extended three-dimensional dendritic array structures under purely diffusive growth conditions. Through carefully designed velocity jump experiments and detailed examination of sub-grain boundary dynamics, we characterize key instabilities, including elimination and tertiary branching, shedding new light on the mechanisms governing dynamic dendritic spacing selection in extended 3D arrays. Phase field simulations are performed to characterize the stability limits of dendritic array structures for quantitative comparison with the flight experiments. Although the simulations capture general trends, significant deviations are noted at the upper stability boundary, indicating the influence of additional, unexplored factors. These findings contribute to a deeper understanding of dendritic growth dynamics and offer valuable benchmark data that could aid in refining predictive models and improving control of dendritic microstructures in metallurgical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Phase-field model of alloy solidification far from chemical equilibrium at the solid-liquid interface

We further develop a recently introduced phase-field model of far-from-equilibrium alloy solidification under additive manufacturing conditions [K. Ji et al., Phys. Rev. Lett. 130, 026203 (2023)]. This model utilizes enhanced solute diffusivity within the spatially diffuse interface region to quantitatively capture solute trapping with a larger interface width, thereby making simulations on experimentally relevant length and timescales computationally feasible. The main developments presented here include testing the robustness of different variational formulations, extending the model to concentrated alloys by incorporating solid and liquid free energies from thermodynamic databases, as illustrated for hypoeutectic Al-Ag alloys with CALPHAD, extending convergence tests as a function of interface width to 3D, and carrying out simulations in both 2D and 3D to examine existing theories of microstructure development. Our results indicate that the simplest variational formulation that interpolates the bulk free-energy density between its solid and liquid forms is the most robust. Remarkably, for hypoeutectic Al-Ag alloys, this formulation yields a high-velocity nonequilibrium phase diagram that is independent of interface width, thereby demonstrating that the framework of enhanced solute diffusivity can be nontrivially extended to concentrated alloys. Other variational formulations have restricted ranges of materials or processing parameters that can be reliably modeled. We use 2D simulations to construct high-velocity microstructure selection maps for dilute Al-Cu alloys. The results validate the important role of latent heat rejection at the interface and extend the limited predictions of linear stability analysis [A. Karma and A. Sarkissian, Phys. Rev. E 47, 513 (1993)] and sharp-interface 1D simulations to fully nonlinear regimes. Furthermore, 3D simulations, carried out using a computationally tractable axisymmetric cellular/dendritic interface shape, demonstrate a good convergence similar to that observed in 2D as a function of interface width. Full 3D simulations, in turn, reveal that the standard theory of absolute stability is a good predictor of the upper critical velocity beyond which steady-state growth becomes unstable, despite the different morphological manifestations of this instability in 2D and 3D.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of Magnesium Oxysulfate Formulation for SRPPF Aqueous Recovery Liquid Solidification

The liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery Processes will be solidified into a stable form that is acceptable by Waste Isolation Pilot Plant (WIPP) for disposal. The current Aqueous Recovery flow sheet proposes to solidify the liquid effluent using a grout formula that was developed and tested for the former Waste Solidification Building process. This Portland cement based mixture results in a high pH (~13) leachate from the solidified waste form which is not acceptable to WIPP in the large quantities expected from production at SRPPF. Various cementitious materials were previously evaluated as alternative grout formulations to Portland cement and a MgO-based mix was identified as a promising alternative. A magnesium oxysulfate (MOS) cement formulation comprised of reactive magnesium oxide (MgO), anhydrous magnesium sulfate (MgSO 4 ), and sand, as a non-reactive heat sink provided good mixability, similar density to the original Portland-cement based mix, and a leachate pH of 9.4, within the assumed WIPP brine pH range. However, the MOS formulation exhibited an appreciable amount of heat generation, which resulted in premature setting of a large-scale test.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Effects of SRPPF ARS Effluent Variations on Magnesium Oxysulfate Solidification

A magnesium oxysulfate (MOS) grout formulation has been identified to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). The formulation uses reactive, light burnt MgO (28 wt%), anhydrous MgSO 4 (10 wt%), and dead burnt MgO (62 wt%), resulting in a grout with good mixability, acceptable density, acceptable setting times, and a leachate pH around 9.4, within the assumed Waste Isolation Pilot Plant (WIPP) brine pH range. A series of tests were then designed to observe how this formula reacted to variations in the liquid effluent. Liquid effluent temperature, the caustic pH level, concentration of NaNO 3 , and the presence of neutralization products, trace metals, and/or sodium sulfate (all potential residuals found in the effluent from upstream processing), were evaluated to see how each impacts the grout mixing time, peak temperature, setting time, presence of bleed water, leachate pH, and density. The standard mix has an average mixing time of 18 minutes, peak temperature of 100.5 °C, and set time of 60 minutes. Increasing the temperature of the liquid effluent increased the reaction rate of the mix and reduced mixing and setting times. Between 30 and 40°C the change was relatively small, raising no more than 6 °C compared to the standard mix maximum temperature. Increasing the pH of the liquid effluent had no significant impact on the mix. The addition of neutralization products and trace metals had an overall impact of decreasing the reactivity of the mix. The addition of more ions in the liquid effluent, such as an increase in the concentration of NaNO 3 and the addition of Na 2 SO 4 , generally decreased the reactivity of the mix. None of the variations to the liquid effluent hindered solidification as indicated by the lack of bleed water found on all the samples. The leachate pH values for all mixes tested did not significantly vary from the expected pH of 9.4 and none of the density values fell below 1.8 g/cm 3 . Overall, changes to the liquid effluent were found to have a minimal impact on the formulation suggesting the grout's ability to properly form despite increased temperatures and the presence of residuals typically found in the liquid effluent from the ARS.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Sculpting 2D Crystals via Membrane Contractions before and during Solidification

When phospholipids crystallize within the otherwise fluid membranes of giant unilamellar vesicles, the resulting molecularly thin “2D” solids exhibit great variety in their morphology evolution. For example, within membranes containing moderate amounts of the crystallizing component, crystals grow with a fixed morphology depending on vesicle size. Conversely for membranes containing large amounts of the crystallizing species, we find small compact crystals on vesicles of all sizes. However, on large vesicles, growing crystals sprout flower petals that lengthen progressively. These behaviors result from two combined mechanisms: first, like other 2D solids, the shear rigidity of phospholipid crystals renders them intolerant to morphologies with nonzero Gaussian curvature. As a result and especially at elevated membrane tension, the cost of bending elasticity is reduced at the expense of line energy by the formation of flowers as opposed to compact crystals. Second, the composition-dependent tension rise during cooling relaxes via water permeation of the membrane with a time constant scaling as R2. The amount of crystal formed for a small decrease in temperature determines this composition-dependent increase in stress from thermal contractions versus solidification. Surface Evolver computations were motivated using the predicted tension evolution to develop a processing space that maps to experimental observations for initial and growing crystal morphology. Important variable groups are identified, including a scaled ratio of bending to line energy, a vesicle-size-independent group for membrane contractions, and a time constant for stress relaxation. Though processing stresses ultimately relax, the crystal morphology persists well beyond the processing window.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Evolution of dislocations during the rapid solidification in additive manufacturing

Materials processed by fusion-based additive manufacturing (AM) typically exhibit relatively high dislocation densities, along with cellular structures and elemental segregation. This representative structural feature significantly influences material performance; however, post-mortem microstructure characterizations of AM materials cannot capture the dynamic evolution of dislocations during the manufacturing process, thereby offering limited mechanism-based guidance for further advancing AM techniques and facilitating the qualification and certification of AM products. In this study, we conduct operando high-energy synchrotron X-ray diffraction experiments on wire-laser directed energy deposition of 316 L stainless steel. Through a unique configuration, our operando synchrotron experiments semi-quantitatively probe the dislocation density in solid phases and their dynamic changes during solidification and subsequent cooling. By integrating this advanced synchrotron technique with multi-physics simulation, in-situ neutron diffraction, and multi-scale electron microscopy characterization, our mechanistic study aims to elucidate the effects of rapid cooling and subsequent thermal cycling on the dislocation generation and evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation, chemical evolution and solidification of the dense liquid phase of calcium (bi)carbonate

Metal carbonates, which are ubiquitous in the near-surface mineral record, are a major product of biomineralizing organisms and serve as important targets for capturing anthropogenic CO 2 emissions. However, pathways of carbonate mineralization typically diverge from classical predictions due to the involvement of disordered precursors, such as the dense liquid phase (DLP), yet little is known about DLP formation or solidification processes. Using in situ methods we report that a highly hydrated bicarbonate DLP forms via liquid–liquid phase separation and transforms into hollow hydrated amorphous CaCO 3 particles. Acidic proteins and polymers extend DLP lifetimes while leaving the pathway and chemistry unchanged. Molecular simulations suggest that the DLP forms via direct condensation of solvated Ca 2+ •(HCO 3 – ) 2 complexes that react due to proximity effects in the confined DLP droplets. Furthermore, our findings provide insight into CaCO 3 nucleation that is mediated by liquid–liquid phase separation, advancing the ability to direct carbonate mineralization and elucidating an often-proposed complex pathway of biomineralization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Solidification cracking of laser melted commercial-purity tungsten

The high melting temperature of tungsten (W) makes it an attractive candidate for energy generation applications; however, its use is limited by its poor ductility at low temperatures. This limitation affects even melt-based additive manufacturing (AM) processes such as laser powder bed fusion (PBF-LB), with as-fabricated pure W exhibiting both longitudinal and transverse cracks. Metallurgical and processing factors that affect these cracks are still being explored. This work utilizes powderless single-tracks on pure W plates made over a range of power and velocity combinations in three unique PBF-LB setups: one with flowing argon, one with continuous vacuum, and an in situ high-speed synchrotron X-ray radiography setup. Each had different oxygen activities in their build environments. Longitudinal cracks with oxides appearing to exude from the crack were found for tracks deposited in a build environment with argon shield gas, while no such cracks were observed for builds conducted in vacuum. A calculation showed that direct oxygen ingress into the melt pool from the build environment is negligible when argon shield gas is present. Thus, incorporation of spatter is a likely mechanism for oxygen ingress into the melt pool. Radiography showed extensive keyholing, spatter generation, and crack formation at keyhole porosity. A heat transfer calculation showed the crack formation time was consistent with cooling below its ductile-to-brittle transition (DBT) temperature. This work identifies solidification cracking as a feasible mechanism in pure W beyond the well-known DBT related cracking.

Materials science↗
DOE OSTI2026

Volume Change from Solidification Correlation for Hanford Tank Waste.

The U.S. Department of Energy (DOE), Hanford Field Office’s primary mission is to safely and effectively treat Hanford’s tank waste and deliver environmental remediation. Mixed radioactive waste is stored in the underground tanks at the Hanford Site. It was recently estimated that retrieval of the waste in the 200 West Area underground tanks in the SY, S, SX, and U Tank Farms will result in about 41 million gallons of mixed low-level waste (MLLW) (RPP-RPT-65147, Rev. 1). The current plan is to retrieve at least 22 S, SX, and U Farm tanks and pretreat1 to produce pretreated tank waste (PTW) which will be further treated (including solidification /immobilization) for Resource Conservation and Recovery Act (RCRA) Land Disposal Restriction (LDR) organics and inorganics before being transferred to an offsite out-of-state facility for disposal (RPP-PLAN-66135, Rev. 2). In addition, solidified PTW from the 200 East Area may also be transferred to an offsite out-of-state facility for disposal to ensure availability of critical Double-Shell Tank space, meet retrieval obligations, and optimize 200 East Area operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Foam and Unreacted Material Reduction in Magnesium Oxysulfate for SRPPF Waste Solidification

A magnesium oxysulfate (MOS) grout formulation has been proposed to solidify the liquid effluent from the Savannah River Plutonium Processing Facility (SRPPF) Aqueous Recovery System (ARS). This formulation uses a combination of light-burnt MgO, anhydrous MgSO 4 , and dead-burnt MgO resulting in a grout with good mixability and acceptable density. The setting time for the grout is within the operational limits of the SRPPF facility and the leachate pH is ~9.4, which is within the assumed pH range of the brine from the Waste Isolation Pilot Plant (WIPP). When first tested at the 1-gallon small-scale and 55-gallon full-scale, there was a significant foam layer that raised concerns of a nonhomogeneous final form. A nonhomogeneous mixture could have variable density throughout the waste form and therefore allow for unequal shielding. To reduce the potential for unequal shielding in the final form, a series of foam reduction tests were carried out and a final formulation of 28 wt% light burnt MgO, 10 wt% MgSO 4 , and 62 wt% dead burnt MgO was used to remove the foam in under two hours while still maintaining a mix that has an acceptable density, mix time, peak temperature, and set time.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗