SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Proposed design for hybrid high-voltage power-circuit package uses molded plastic for hermetic sealing instead of glass-to-metal seal. New package used to house high-voltage regulators and solid-state switches for applications in aircraft, electric automobiles, industrial equipment, satellites, solarcell arrays, and other equipment in extreme environments.
Innovation uses solid-state Hall-effect sensor to turn electrical circuit on or off. Though normally held off by a small bias magnet, Hall device turns on when strong actuating magnet comes into proximity. Drive magnet moves actuating magnet against restraint of detent magnet.
Cavity-dumped lasers employ electrooptic-effect cell to alternately block and release laser pulse. Cell requires high-speed switching circuit that can apply and remove high voltage. Solid-state circuit employs complementary transistor switches which can switch at rates greater than 5 kHz, eliminate warmup time, provide variable voltage wave-form, and allow polarity reversal.
The objective of NASA's narrowband system activities is to identify, develop, and test the technology needed for future commercial satellite-aided mobile communications systems. Desired characteristics include low service cost, efficient spectrum utilization, and compatibility with terrestrial systems. Ongoing effort includes system concept definition and market analysis. A typical system would need a large spaceborne antenna with 50 to 100 beams, each 0.5 to 0.7 degree wide, onboard switching and processing, linear solid-state amplifiers, and low-cost user terminals. The paper describes current studies and discusses future NASA plans in this field.
Silver-cadmium battery sensing and switching circuit design for satellite electric power systems
Although parallel computation architectures have been known for computers since the 1920s, it was only in the 1970s that microelectronic components technologies advanced to the point where it became feasible to incorporate multiple processors in one machine. Concommitantly, the development of algorithms for parallel processing also lagged due to hardware limitations. The speed of computing with solid-state chips is limited by gate switching delays. The physical limit implies that a 1 Gflop operational speed is the maximum for sequential processors. A computer recently introduced features a 'hypercube' architecture with 128 processors connected in networks at 5, 6 or 7 points per grid, depending on the design choice. Its computing speed rivals that of supercomputers, but at a fraction of the cost. The added speed with less hardware is due to parallel processing, which utilizes algorithms representing different parts of an equation that can be broken into simpler statements and processed simultaneously. Present, highly developed computer languages like FORTRAN, PASCAL, COBOL, etc., rely on sequential instructions. Thus, increased emphasis will now be directed at parallel processing algorithms to exploit the new architectures.
Electrically controlled optical latch consists of a sensitive phototransistor and a solid-state light source. This design requires less current to activate an optically activated switch than in prior art.
Circuit reduces intermittent fan-flutter openings in airflow switch. Circuit ignores brief switch openings due to contact oscillations; however, if switch is open longer than selected interval, control circuit shuts down system and sounds alarm.
Remote Power controllers (RPCs) are devices that combine in one unit the capability to perform all the needed functions of load switching and provide total system protection of equipment and wires. The unique developments of solid-state RPCs for 120 Vdc power distribution systems are reviewed. The discussion covers design guidelines, power switch design concepts, and performance effectiveness. An NPN transistor is used as the the basic switch element. Since the ultimate goal of the 120 Vdc RPC program is to demonstrate technology readiness, the final phase is directed to the design, fabrication, and testing of multi-chip hybrid prototypes in hermetically sealed packages. RPCs have potential application in spacecraft and aircraft electrical systems, in transportation systems, and various industrial applications. The upper voltage limitation on the RPC design is related to the capability and availability of suitable high-voltage power transistors. The merits of solid-state RPCs are noted.
A pulsed, actively mode-locked, pulse-transmission-mode (PTM) Q-switched Nd:YAG laser has been developed for a planned NASA spaceborne precision ranging system. The laser emits single, 150-psec, 20-mJ pulses at 10 pulses per second at 1.064 micrometers.
A feasibility study to design and demonstrate solid-state switchgear composed of circuit breakers and a power transfer switch is described. The switchgear operates on a nominal 270 Vdc circuit and controls power to a load up to 15 A. One circuit breaker may be interconnected to a second to form a power transfer switch. Breaker or switch on-off and transfer functions can be remotely controlled. Automatic overload trip-out is provided through an ultimate current trip and an I squared t trip for transient overcurrents lower than the ultimate current trip level. A number of reclosures with variable time delay between trip-out and reclosure are programmed and controlled by integrated analog and COSMOS logic circuits. A commutation circuit that creates minimal transient disturbances to either source or load was developed to interrupt current flow through the main SCR switching element.-
Investigation into the uses of step-recovery diodes /SRD's/ leads to the development of necessary circuitry for using fast current-switching capabilities of SRD's in frequency multiplication, the design of solid-state X-band transmitters employing SRD multipliers, and the use of SRD multipliers in a phased-array receiving antenna.
Attitude controllers are used to guide roll, pitch, and yaw of vehicle in flight. Controllers enclose multitude of switches, gears, cams, and other hardware needed to transmit pilot's commands to attitude control systems. New design, using magnetic coupled transducers, eliminates many mechanical parts, improving reliability and reducing maintenance.
Circuit concepts for realization of highly reliable and efficient electronic subsystems and microminiaturization application - switching amplifier analysis
Two general types of remote power controller (RPC) that combine the functions of a circuit breaker and a switch were developed for use in direct-current (dc) aerospace systems. Power-switching devices used in these designs are the relatively new gate-turnoff thyristor (GTO) and poweer metal-oxide-semiconductor field-effect transistors (MOSFET). The various RPC's can switch dc voltages to 1200 V and currents to 100 A. Seven different units were constructed and subjected to comprehensive laboratory and thermal vacuum testing. Two of these were dual units that switch both positive and negative voltages simultaneously. The RPC's using MOSFET's have slow turnon and turnoff times to limit voltage spiking from high di/dt. The GTO's have much faster transition times. All RPC's have programmable overload tripout and microsecond tripout for large overloads. The basic circuits developed can be used to build switchgear limited only by the ratings of the switching device used.
SPS satellite power distribution systems are described. The reference Satellite Power System (SPS) concept utilizes high-voltage klystrons to convert the onboard satellite power from dc to RF for transmission to the ground receiving station. The solar array generates this required high voltage and the power is delivered to the klystrons through a power distribution subsystem. An array switching of solar cell submodules is used to maintain bus voltage regulation. Individual klystron dc voltage conversion is performed by centralized converters. The on-board data processing system performs the necessary switching of submodules to maintain voltage regulation. Electrical power output from the solar panels is fed via switch gears into feeder buses and then into main distribution buses to the antenna. Power also is distributed to batteries so that critical functions can be provided through solar eclipses.
Hybrid microelectronics relay has characteristics significantly superior to conventional solid state relays. Relay provides 2500 Vdc input to output isolation and operates from high threshold logic signal to switch load of 400 Vdc at 2 mA. Technology should be of interest to manufacturers of discrete components.
Compact, solid state, electric-power controller switches power on and off at remote load, limits current drawn by load, and shuts off (with 2- to 3- second trip time) in case of short circuit. Lightweight efficient hybrid unit operates at 28 volts dc and at maximum currents of from 3 to 2 amperes.