Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development of GaAs solar cells

Solar cells and mesa diodes were fabricated by the implantation of zinc or beryllium ions into n-type gallium arsenide. Annealing temperatures above 750 C (zinc) or 650 C (beryllium) were found to produce 50% to 100% activation of the implanted ions. Junction depths of about 0.4 micron were produced by 600 keV zinc implants or 70 keV beryllium implants. P-layer sheet resistance was about 150 ohms for 2 x 10 to the 15th power cm/2 zinc or 1 x 10 to the 15th power cm/2 beryllium implants. This is sufficiently low for efficient solar cell fabrication. Contacting procedures were improved to yield reproducibly adherent, low resistance front and back contacts.

Source record↗
NASA NTRS1977

Radiation tests of SEP solar cells

Solar cells specially designed for Solar Electric Propulsion (SEP) were tested with radiation fluences up to 10 to the 12th power protons having energies of 1.5, 1.0, and 0.5 MeV, and with fluences up to 10 to the 16th power electrons having 1.0 MeV energy. Spectrolab cells having a back-surface field were also irradiated with the same particles and fluences. Cell performances are described by curves in which normalized and absolute values of maximum power, maximum-power voltage, short-circuit current, and open-circuit voltage are plotted as a function of fluence.

Oman, H.↗
NASA NTRS1990

Development of high-performance GaInAsP solar cells for tandem solar cell applications

Recent results in the development of high-efficiency, low-bandgap GaInAsP solar cells epitaxially grown and lattice matched on InP substrates are presented. Such cells are intended to be used as optimum bottom cell components in tandem solar cells. Assuming that a GaAs-based top cell is used, computer simulation of the potential bottom cell performance as a function of the cell bandgap and incident spectrum indicates that two particular alloys are desirable: Ga0.47In0.53As (Eg = 0.75 eV) for space applications and Ga0.25In0.75As0.54P0.46 (Eg = 0.95 eV) for terrestrial applications. In each of these materials, solar cells with new record-level efficiencies have been fabricated. The efficiency boost available to tandem configurations from these low-bandgap cells is discussed.

Wanlass, M. W.↗
NASA NTRS1982

Orienting and Applying Flux to Solar Cells

Solar cells are oriented and fluxed automatically at first work station along solar-array assembly line. In under 2 seconds rotary drive rotates cell into proper position for applying solder flux to bus pad on collector side. When contact bus pad is in correct position, capstan drive is disengaged, and vacuum holddown beneath cell is turned on. Flux system lowers and applies preset amount of solder flux to bus pad. Two interconnect tabs are soldered to fluxed areas.

Feder, H.↗
NASA NTRS1994

Flexible Solar Cells

Solar cell "modules" are plastic strips coated with thin films of photovoltaic silicon that collect solar energy for instant conversion into electricity. Lasers divide the thin film coating into smaller cells to build up voltage. Developed by Iowa Thin Film Technologies under NASA and DOE grants, the modules are used as electrical supply for advertising displays, battery rechargers for recreational vehicles, and to power model airplanes. The company is planning other applications both in consumer goods and as a power source in underdeveloped countries.

Source record↗
NASA NTRS1970

Improved cover for cadmium sulfide solar cells

Solar cell performance and radiation resistance is improved by application of 1-mil thickness of Teflon FEP protective material. Cells produce 30 percent more power than similar cells with conventional Kapton covers.

Anagnostou, E.↗
NASA NTRS1971

Study to determine and improve design for lithium-doped solar cells

Solar cell experiments show that a single lithium density parameter, the lithium density gradient, calculated from nondestructive capacitance measurements, provides the basis for accurate predictions of lithium cell behavior in a 1-MeV electron environment for fluences ranging between 3 X 10 to the 13th power e/sq cm and 3 X 10 to the 15th power/e sq cm. The oxygen-rich (quartz crucible) lithium cell with phosphorous starting dopant and lithium gradient between approximately 5 X 10 to the 18th power and 1.5 x 10 to the 19th power/cm to the 4th power was found superior in performance to the commercial 10 ohm-cm n/p control cells. Post-recovery stability of oxygen-rich cells was satisfactory. An average post-recovery current drop of approximately 1 mA was observed for 70 crucible cells after 1 year-equivalent storage time at 80 C. In contrast the oxygen-poor (float zone and Lopex) lithium cells displayed spotty initial performance and stability problems at room temperature.

Brucker, G.↗
NASA NTRS1972

Breakdown phenomena in reverse biased silicon solar cells.

Solar cell reverse current-voltage characteristics have been found to vary widely and to be generally unstable. At reverse voltages greater than approximately 20 V and at cell power dissipations of more than 4 W, the probability of permanent breakdown, resulting in cell short-circuit failure, was found to increase with increasing voltage and exposure time. Shorted cells showed evidence of cell contact material and silicon melting in very localized areas with lava-like flow patterns and channels bridging the p and n contacts.

Rauschenbach, H. S.↗
NASA NTRS1976

Uniform solar cells

Solar cells used in radiation sensors can be efficiently matched by individual trimming. Strip of aluminized Mylar is used to adjust cell output to within required tolerances. Method is faster than individual selection of matched cells.

Source record↗
NASA NTRS1980

Low cost processes for fabricating silicon solar cells

Solar cell fabrication processes, in particular junction formation and metallization, are evaluated in terms of cell efficiencies, process yields, module packing factors, and energy cost effectiveness. It is shown that for junction formation, the diffusion processes provide a relatively low-cost approach. The costs per unit cell area can be further reduced by increased wafer area and mechanized wafer handling. The costs for a large number of metallization processes, excluding the costs of the metal, are roughly comparable. However, their varying influence on cell performance leads to a significant spread in the allowable process costs.

Goldman, H.↗
NASA NTRS1981

Diagnostic study of BSF silicon solar cells

Solar cells equipped with back surface fields (BSF) were fabricated by means of an aluminum alloy, boron diffusion, and boron ion implantation. The importance of initial thickness, resistivity, orientation, and the crystal growth method were examined. Aluminum in paste form was screen printed on the cell, followed by alloy formation at 800 C for a minute. Application of the BSFs resulted in open circuit voltage improvements dependent on the substrate resistivity, ranging from 10 mV at 0.3 ohm-cm to 50 mV at 15 ohm-cm. The gains in performance were attributed to a longer penetration depth, a heightened concentration profile at the interface, and higher concentrations in the p+ layer.

Yoo, H.↗