Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Sawtooth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Vertically reciprocating auger

The mathematical model and test results developed for the Vertically Reciprocating Auger (VRA) are summarized. The VRA is a device capable of transporting cuttings that result from below surface drilling. It was developed chiefly for the lunar surface, where conventional fluid flushing while drilling would not be practical. The VRA uses only reciprocating motion and transports material through reflections with the surface above. Particles are reflected forward and land ahead of radially placed fences, which prevent the particles from rolling back down the auger. Three input wave forms are considered to drive the auger. A modified sawtooth wave form was chosen for testing, over a modified square wave or sine wave, due to its simplicity and effectiveness. The three-dimensional mathematical model predicted a sand throughput rate of 0.2667 pounds/stroke, while the actual test setup transported 0.075 pounds/stroke. Based on this result, a correction factor of 0.281 is suggested for a modified sawtooth input.

Etheridge, Mark↗
NASA NTRS2007

Flaperon Modification Effect on Jet-Flap Interaction Noise Reduction for Chevron Nozzles

Jet-flap interaction (JFI) noise can become an important component of far field noise when a flap is immersed in the engine propulsive stream or is in its entrained region, as in approach conditions for under-the-wing engine configurations. We experimentally study the effect of modifying the flaperon, which is a high speed aileron between the inboard and outboard flaps, at both approach and take-off conditions using scaled models in a free jet. The flaperon modifications were of two types: sawtooth trailing edge and mini vortex generators (vg s). Parametric variations of these two concepts were tested with a round coaxial nozzle and an advanced chevron nozzle, with azimuthally varying fan chevrons, using both far field microphone arrays and phased microphone arrays for source diagnostics purposes. In general, the phased array results corroborated the far field results in the upstream quadrant pointing to JFI near the flaperon trailing edge as the origin of the far field noise changes. Specific sawtooth trailing edges in conjunction with the round nozzle gave marginal reduction in JFI noise at approach, and parallel co-rotating mini-vg s were somewhat more beneficial over a wider range of angles, but both concepts were noisier at take-off conditions. These two concepts had generally an adverse JFI effect when used in conjunction with the advanced chevron nozzle at both approach and take-off conditions.

Thomas, Russell H.↗
NASA NTRS2004

Fabricating Blazed Diffraction Gratings by X-Ray Lithography

Gray-scale x-ray lithography is undergoing development as a technique for fabricating blazed diffraction gratings. As such, gray-scale x-ray lithography now complements such other grating-fabrication techniques as mechanical ruling, holography, ion etching, laser ablation, laser writing, and electron-beam lithography. Each of these techniques offers advantages and disadvantages for implementing specific grating designs; no single one of these techniques can satisfy the design requirements for all applications. Gray-scale x-ray lithography is expected to be advantageous for making gratings on steeper substrates than those that can be made by electron-beam lithography. This technique is not limited to sawtooth groove profiles and flat substrates: various groove profiles can be generated on arbitrarily shaped (including highly curved) substrates with the same ease as sawtooth profiles can be generated on flat substrates. Moreover, the gratings fabricated by this technique can be made free of ghosts (spurious diffraction components attributable to small spurious periodicities in the locations of grooves). The first step in gray-scale x-ray lithography is to conformally coat a substrate with a suitable photoresist. An x-ray mask (see Figure 1) is generated, placed between the substrate and a source of collimated x-rays, and scanned over the substrate so as to create a spatial modulation in the exposure of the photoresist. Development of the exposed photoresist results in a surface corrugation that corresponds to the spatial modulation and that defines the grating surface. The grating pattern is generated by scanning an appropriately shaped x-ray area mask along the substrate. The mask example of Figure 1 would generate a blazed grating profile when scanned in the perpendicular direction at constant speed, assuming the photoresist responds linearly to incident radiation. If the resist response is nonlinear, then the mask shape can be modified to account for the nonlinearity and produce a desired groove profile. An example of grating grooves generated by this technique is shown in Figure 2. A maximum relative efficiency of 88 percent has been demonstrated.

Mouroulis, Pantazis↗
NASA NTRS2013

Whole Wafer Design and Fabrication for the Alignment of Nanostructures for Chemical Sensor Applications

A major objective in aerospace sensor development is to produce sensors that are small in size, easy to batch fabricate and low in cost, and have low power consumption The fabrication of chemical sensors involving nanostructured materials can provide these properties as well as the potential for the development of sensor systems with unique properties and improved performance. However, the fabrication and processing of nanostructures for sensor applications currently is limited in the ability to control their location on the sensor. Currently, our group at NASA Glenn Research Center has demonstrated the controlled placement of nanostructures in sensors using a sawtooth patterned electrode design. With this design the nanostructures are aligned between opposing sawtooth electrodes by applying an alternating current.

Biaggi-Labiosa, Azlin M.↗
NASA NTRS1965

Traveling-wave tube circuit simplifies microwave relay

Circuit with a sawtooth-modulated traveling-wave tube, which acts as a frequency converter and as an amplifier, simplifies microwave transmission. Lower power losses and reduced size and weight are also realized in this circuit.

Allen, W. K.↗
NASA NTRS1966

Circuit operates as sine function generator

Electronic circuit drives sine function generator using square wave and sawtooth sweep generators. The circuit replaces electromechanical driver and increases accuracy.

Bogart, T., Jr.↗
NASA NTRS1967

Series transistors isolate amplifier from flyback voltage

Circuit enables high sawtooth currents to be passed through a deflection coil and isolate the coil driving amplifier from the flyback voltage. It incorporates a switch consisting of transistors in series with the driving amplifier and deflection coil. The switch disconnects the deflection coil from the amplifier during the retrace time.

Banks, W.↗
NASA NTRS1972

One-phonon transitions observed in the scattering of He atoms from a LiF/001/ surface.

For the scattering of a nearly monoenergetic beam of thermal-energy He atoms from a cleaved (001)LiF crystal surface, speed distributions of the reflected atoms are measured at suitably spaced scattering angles within the plane of incidence. From the measurements, elastic and one-phonon inelastic scattering processes are identified. Elastically scattered atoms distribute themselves in a set of sharp diffraction peaks. One-phonon inelastically scattered atoms are dispersed about each diffraction peak. The most probable velocities of the inelastically scattered atoms exhibit a characteristic sawtooth variation with scattering angle which, to first approximation, corresponds to conservation of the component of atom momentum tangent to the surface.-

Fisher, S. S.↗
NASA NTRS1974

Geologic structure in California: Three studies with ERTS-1 imagery

Results are presented of three early applications of imagery from the NASA Earth Resources Technology Satellite to geologic studies in California. In the Coast Ranges near Monterey Bay, numerous linear drainage features possibly indicating unmapped fracture zones were mapped within one week after launch of the satellite. A similar study of the Sierra Nevada near Lake Tahoe revealed many drainage features probably formed along unmapped joint or faults in granitic rocks. The third study, in the Peninsular Ranges, confirmed existence of several major faults not shown on published maps. One of these, in the Sawtooth Range, crosses in Elsinore fault without lateral offset; associated Mid-Cretaceous structures have also been traced continuously across the fault without offset. It therefore appears that displacement along the Elsinore fault has been primarily of a dip-slip nature, at least in this area, despite evidence for lateral displacement elsewhere.

Lowman, P. D., Jr.↗
NASA NTRS1976

Evidence for open field lines in Jupiter's magnetosphere

A model for the night-side Jovian magnetic field is derived partly on the basis of theoretical considerations and partly on the basis of the magnetic-field data obtained during the outbound leg of the path of Pioneer 10. This model can explain the observed sawtooth modulation of energetic particle fluxes in terms of closed and open field lines that cannot contain the particles. The model is applicable only to the Jovian magnetotail.

Goertz, C. K.↗
NASA NTRS1977

A description of the software analysis from flight and simulation data of the course cut limiter in the TCV b-737 area navigation computer

During automatic horizontal path captures, the (Terminal Configured Vehicle) B-737 airplane maintained smaller than designed path intercept angles and experienced a sawtooth bank angle oscillation during its turn towards the path. From flight data, it was determined that these anomalies were caused by the improper output of the course cut limiter in the horizontal path control law. The output from the course cut limiter did not obtain its full value and it was calculated stepwise discontinuously. The automatic horizontal path captures were then conducted on the TCV B-737 airplane real-time simulation. The path intercept angles were maintained properly and no bank angle oscillation was encountered. Data showed that the course cut limiter was calculated at its full value in a continuous manner. The intermediate calculations of the course cut limiter in the airplane's navigation computer were rewritten and rescaled in such a manner that truncation errors could be minimized. The horizontal path capture tests were then reflown. The airplane maintained the proper path intercept angle and no bank angle oscillations occurred on any of the tests.

Knox, C. E.↗
NASA NTRS1977

Low cost solar energy collection system

A fixed, linear, ground-based primary reflector having an extended, curved sawtooth contoured surface covered with a metallized polymeric reflecting material, reflected solar energy to a movably supported collector that was kept at the concentrated line focus of the reflector primary. Efficient utilization leading to high temperatures from the reflected solar energy was obtained by cylindrical shaped secondary reflectors that directed off-angle energy to the absorber pipe.

Miller, C. G.↗
NASA NTRS1978

Acoustical effects of blade tip shape changes on a full scale helicopter rotor in a wind tunnel

Four tip shapes were tested. They were rectangular, swept, tapered, and swept-tapered. The measured data covered a wide range of operating conditions. The range of advancing tip Mach numbers were between 0.72 to 0.96, and the advance ratios were from 0.2 to 0.375. At low and moderate advancing tip Mach number, the data in the dbA scale appear to indicate the swept tip is the quietest, swept tapered the second, tapered third and rectangular the most noisy. Above an advancing tip Mach number of about 0.89, a distinct acoustical pulse can be observed, which dominates the acoustical waveform. The pulse shape is symmetric at moderate tip Mach number, changing to a sawtooth shape at high advancing tip Mach numbers. Based on the amplitude of the impulsive noise, it appears the swept-tapered tip is the quietest, tapered tip the second, swept tip third and square tip the most noisy. The data presented in this report should be useful as data bases for modeling and evaluating helicopter impulsive noise.

Lee, A.↗
NASA NTRS1978

Primary reflector for solar energy collection systems

A fixed, linear, ground-based primary reflector is disclosed which has an extended curved sawtooth-contoured surface covered with a metalized polymeric reflecting material. The device reflects solar energy to a movably supported collector that is kept at the concentrated line focus of the reflector primary. The primary reflector may be constructed by a process utilizing well-known freeway paving machinery.

Miller, C. G.↗
NASA NTRS1979

Primary reflector for solar energy collection systems and method of making same

Solar energy is reflected to a movably supported collector that is kept at the concentrated line focus of the reflector primary by a fixed, linear, ground-based primary reflector having an extended curved sawtooth contoured surface covered with a metalized polymeric reflecting material. The primary reflector was constructed by a process utilizing well-known freeway paving machinery.

Miller, C. G.↗