Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SURFACE ROUGHNESS EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Fatigue behavior and modeling for additive manufactured 304L stainless steel: The effect of surface roughness

The fatigue strength of additively manufactured metallic parts in their as-built surface condition is mainly dominated by the surface roughness. Post-processing is often inevitable to reduce surface roughness effects even though post-processing diminishes the main advantage of additive manufacturing, which is net-shaped direct-to-service production. This work investigates the underlying mechanisms responsible for fatigue failure of additively manufactured 304L stainless steel parts in as-built and machined/polished surface conditions. Both strain- and force-controlled, fully reversed fatigue tests were conducted to gain a comprehensive understanding of surface roughness effects on fatigue behavior. The sensitivity to surface roughness is shown to be dependent on the control mode, with stress-based fatigue tests showing greater sensitivity than strain-based fatigue tests. Moreover, the fatigue life estimation for as-built specimens was performed based on surface roughness parameters as well as the fatigue properties of the specimens in machined/polished surface condition of the material without using any fatigue data of specimens in as-built surface condition. Accordingly, the effect of surface roughness on the fatigue behavior could be estimated reasonably well in both strain-life and stress-life approaches.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Surface roughness effects with solid lubricants dispersed in mineral oils

The lubricating effectiveness of solid-lubricant dispersions are investigated in both point and line contacts using surfaces with both random and directional roughness characteristics. Friction and wear data obtained at relatively low speeds and at room temperature, indicate that the existence of solid lubricants such as graphite, MoS2, and PTFE in a plain mineral oil generally will not improve the effectiveness of the oil as a lubricant for such surfaces. Under boundary lubrication conditions, the friction force, as a function of time, initially depends upon the directional roughness properties of the contacting surfaces irrespective of whether the base oil or dispersions are used as lubricants.

Cusano, C.↗
DOE OSTI2021

Surface Roughness Effects on Heat Transfer in Additively Manufactured sCO 2 Cycle Heat Exchangers

An experimental study was performed to consider the impact of surface roughness on heat transfer and pressure drop to supercritical carbon dioxide (sCO 2 ) in additively manufactured channels. All tests were performed in the Heat Exchange and Experimental Testing (HEET) rig at the U.S. Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) in Morgantown, West Virginia. Four test articles were considered. The first was a hydrodynamically smooth, drawn tube. The other three were additively manufactured channels with square and rectangular cross sections, which were characterized by sand-grain roughness to hydraulic diameter ratios spanning 0.0029 to 0.0073. Friction factors were determined by measuring the tube mass flow rate and pressure drop. The tube side heat transfer coefficient was measured using the Wilson plot technique. It was found that the friction factor results were 8% greater than the Colebrook correlation. Greater deviation was observed between the heat transfer results and the correlations. The Gnielinski correlation overpredicted the experimental points by nominally 30% and the Norris correlation overpredicting the experimental points by nominally 25%. A thermal performance factor was formed from the friction factor augmentation and Nusselt number augmentation results. These results indicated a 10% improvement in heat duty for a heat exchanger constructed utilizing a tube with ϵ/D_h =0.0073 relative to a heat exchanger utilizing a smooth, conventional tube.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Surface roughness effects on equilibrium temperature.

An analysis is presented for evaluation of equilibrium temperature distribution on radiatively adiabatic, adjoint planes which are uniformly irradiated by a collimated solar flux. The analysis employs a semigrey spectral model. Radiation properties for surface emitted radiation are obtained from the expressions of electromagnetic theory for smooth surfaces. Rough surface properties for solar radiation are given by the Beckmann bidirectional reflectance model. Numerical solutions to the governing equations yield equilibrium temperature distributions for a range of the influencing parameters. Surface roughness has little influence on equilibrium temperature for materials with high values for solar absorptance. However, for low or intermediate values of solar absorptance, roughness effects on the spatial distribution of reflected solar radiation can significantly alter equilibrium temperature particularly at surface elements where radiant interaction is small.

Houchens, A. F.↗
NASA NTRS1992

Detecting surface roughness effects on the atmospheric boundary layer via AIRSAR data: A field experiment in Death Valley, California

The part of the troposphere influenced by the surface of the earth is termed the atmospheric boundary layer. Flow within this layer is influenced by the roughness of the surface; rougher surfaces induce more turbulence than smoother surfaces and, hence, higher atmospheric transfer rates across the surface. Roughness elements also shield erodible particles, thus decreasing the transport of windblown particles. Therefore, the aerodynamic roughness length (z(sub 0)) is an important parameter in aeolian and atmospheric boundary layer processes as it describes the aerodynamic properties of the underlying surface. z(sub 0) is assumed to be independent of wind velocity or height, and dependent only on the surface topography. It is determined using in situ measurements of the wind speed distribution as a function of height. For dry, unvegetated soils the intensity of the radar backscatter (sigma(sup 0)) is affected primarily by surface roughness at a scale comparable with the radar wavelength. Thus, both wind and radar respond to surface roughness variations on a scale of a few meters or less. Greeley showed the existence of a correlation between z(sub 0) and sigma(sup 0). This correlation was based on measurements over lava flows, alluvial fans, and playas in the southwest deserts of the United States. It is shown that the two parameters behave similarly also when there are small changes over a relatively homogeneous surface.

Blumberg, Dan G.↗
NASA NTRS1987

Use of a liquid-crystal, heater-element composite for quantitative, high-resolution heat transfer coefficients on a turbine airfoil, including turbulence and surface roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at roon temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, Steven A.↗
NASA NTRS1987

Use of a liquid-crystal and heater-element composite for quantitative, high-resolution heat-transfer coefficients on a turbine airfoil including turbulence and surface-roughness effects

Local heat transfer coefficients were measured along the midchord of a three-times-size turbine vane airfoil in a static cascade operated at room temperature over a range of Reynolds numbers. The test surface consisted of a composite of commercially available materials: a Mylar sheet with a layer of cholestric liquid crystals, which change color with temperature, and a heater made of a polyester sheet coated with vapor-deposited gold, which produces uniform heat flux. After the initial selection and calibration of the composite sheet, accurate, quantitative, and continuous heat transfer coefficients were mapped over the airfoil surface. Tests were conducted at two free-stream turbulence intensities: 0.6 percent, which is typical of wind tunnels; and 10 percent, which is typical of real engine conditions. In addition to a smooth airfoil, the effects of local leading-edge sand roughness were also examined for a value greater than the critical roughness. The local heat transfer coefficients are presented for both free-stream turbulence intensities for inlet Reynolds numbers from 1.20 to 5.55 x 10 to the 5th power. Comparisons are also made with analytical values of heat transfer coefficients obtained from the STAN5 boundary layer code.

Hippensteele, S. A.↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $ \$ $6B annually (at $ \$ $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year), and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE) missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

42 ENGINEERING↗
DOE OSTI2023

Surface Roughness Effects from Additive Manufacturing in High Efficiency Gas Turbine Combustion Systems

In the past, clean combustion systems were characterized by high system development costs due to growing complexity and escalating manufacturing costs from conventional manufacturing processes. As a result, high efficiency concepts are difficult to design and more difficult to be cost-effectively manufactured. In recent years, with the introduction of additive manufacturing (AM) technologies, the rapid prototyping and mass production processes of clean combustion systems are promising to be significantly simplified with significant reduction in terms of engine manufacturing cost and engine energy cost. Compared with conventional manufacturing built parts, the AM process enabled a simpler design to be adopted for the nozzle, reducing the number of required braze and weld joints from twenty-five to just five. The resulting nozzle was 25% lighter and five times more durable and contributed to a 15% reduction in fuel burn in comparison with the previous model produced. Applying these improvements to a fleet of 5,000 turbofan engines at 150 kN thrust would result in fuel cost savings of $6B annually (at $5/gallon Jet-A fuel price, 700 gallon/hour fuel consumption rate, and 2,300 operational hours per year),and reduce CO2 emissions by more than 25 million tons per year. These advances support core Department of Energy (DOE)missions in energy efficiency, improving productivity, and environmental sustainability. Maximizing the benefit of these new capabilities will require high prediction capability of high speed turbulent flow with wall modeled Large Eddy Simulation (LES). GE Aviation maintains that advanced simulation technology and supercomputing is required in order to provide the appropriate boundary conditions to realize the maximum potential of AM and Ceramic Matrix Composite to reduce cooling flow, a first order penalty on the Brayton cycle. The algorithm developed using the ANSYS/Fluent software would provide the foundation for entirely new avenues of research and development with potential multi-billion dollar impact to the US economy, and significant reduction in carbon based emissions across the aerospace and power generation industries. The formulation of this iWLES (integral wall model for LES) is generic and allows to capture the changes in flow dynamics that have a significant impact on the wall bounded flow characteristics, such as swirler effective area, bulk swirl number, local pressure distribution, exit velocity profile, and turbulence kinetic energy profile. A periodic channel flow with rough flat plate is simulated using LES (Wall-Adapting Local Eddy-viscosity) model to verify the implementation of iWLES in the Fluent User Defined Function (UDF). As the flow fields are highly sensitive due to surface roughness of the wall bounded flows in the combustion systems, there is significant potential to conduct further LES studies focusing on the turbulence boundary layer interaction. Accurately capturing near wall physics will elucidate the impact of rough surfaces on combustor flow and aero-thermal interactions.

99 GENERAL AND MISCELLANEOUS↗
NASA NTRS1981

Effect of Surface Roughness on Hydrodynamic Bearings

A theoretical analysis on the performance of hydrodynamic oil bearings is made considering surface roughness effect. The hydrodynamic as well as asperity contact load is found. The contact pressure was calculated with the assumption that the surface height distribution was Gaussian. The average Reynolds equation of partially lubricated surface was used to calculate hydrodynamic load. An analytical expression for average gap was found and was introduced to modify the average Reynolds equation. The resulting boundary value problem was then solved numerically by finite difference methods using the method of successive over relaxation. The pressure distribution and hydrodynamic load capacity of plane slider and journal bearings were calculated for various design data. The effects of attitude and roughness of surface on the bearing performance were shown. The results are compared with similar available solution of rough surface bearings. It is shown that: (1) the contribution of contact load is not significant; and (2) the hydrodynamic and contact load increase with surface roughness.

Majumdar, B. C.↗