Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOLDERED JOINT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Automated inspection of solder joints for surface mount technology

Researchers at NASA/GSFC evaluated various automated inspection systems (AIS) technologies using test boards with known defects in surface mount solder joints. These boards were complex and included almost every type of surface mount device typical of critical assemblies used for space flight applications: X-ray radiography; X-ray laminography; Ultrasonic Imaging; Optical Imaging; Laser Imaging; and Infrared Inspection. Vendors, representative of the different technologies, inspected the test boards with their particular machine. The results of the evaluation showed limitations of AIS. Furthermore, none of the AIS technologies evaluated proved to meet all of the inspection criteria for use in high-reliability applications. It was found that certain inspection systems could supplement but not replace manual inspection for low-volume, high-reliability, surface mount solder joints.

Savage, Robert M.↗
NASA NTRS1970

Prevention of cracking of soldered joints in electronic assemblies

Printed circuit board design allows for thermal stressing of the soldered joints during many thermal cycles. Components' leads should be cleaned, tinned, and freed of particles that prevent solder adherence, have a thin conformal coating, and have an air space between the coating and the body of the component.

Beasley, B.↗
NASA NTRS1989

Magellan/Galileo solder joint failure analysis and recommendations

On or about November 10, 1988 an open circuit solder joint was discovered in the Magellan Radar digital unit (DFU) during integration testing at Kennedy Space Center (KSC). A detailed analysis of the cause of the failure was conducted at the Jet Propulsion Laboratory leading to the successful repair of many pieces of affected electronic hardware on both the Magellan and Galileo spacecraft. The problem was caused by the presence of high thermal coefficient of expansion heat sink and conformal coating materials located in the large (0.055 inch) gap between Dual Inline Packages (DIPS) and the printed wiring board. The details of the observed problems are described and recommendations are made for improved design and testing activities in the future.

Ross, Ronald G., Jr.↗
NASA NTRS1991

A systems approach to solder joint fatigue in spacecraft electronic packaging

Differential expansion induced fatigue resulting from temperature cycling is a leading cause of solder joint failures in spacecraft. Achieving high reliability flight hardware requires that each element of the fatigue issue be addressed carefully. This includes defining the complete thermal-cycle environment to be experienced by the hardware, developing electronic packaging concepts that are consistent with the defined environments, and validating the completed designs with a thorough qualification and acceptance test program. This paper describes a useful systems approach to solder fatigue based principally on the fundamental log-strain versus log-cycles-to-failure behavior of fatigue. This fundamental behavior has been useful to integrate diverse ground test and flight operational thermal-cycle environments into a unified electronics design approach. Each element of the approach reflects both the mechanism physics that control solder fatigue, as well as the practical realities of the hardware build, test, delivery, and application cycle.

Ross, R. G., Jr.↗
NASA NTRS2006

Solder joint fatigue analysis under low temperature Martian conditions

Electronics, without requiring heater power or enclosure in a centralized 'warm electronics box,' will need to survive mean surface temperatures of -120 degrees Celsius to +20 degrees Celsius for an extended Martian mission and an operational temperature up to 85 degrees Celsisus. Since these electronics will need to survive extended cycles under these conditions, fatigue is a significant concern. The solder joint reliability of connectors on a printed wiring board was investigated.

low temperature↗
NASA NTRS2006

Experimental Investigation of Solder Joint Defect Formation and Mitigation in Reduced-Gravity Environments

This paper documents a research effort on reduced gravity soldering of plated through hole joints which was conducted jointly by the National Center for Space Exploration Research, NASA Glenn Research Center, and NASA Johnson Space Center. Significant increases in joint porosity and changes in external geometry were observed in joints produced in reduced gravity as compared to normal gravity. Multiple techniques for mitigating the observed increase in porosity were tried, including several combinations of flux and solder application techniques, and demoisturizing the circuit board prior to soldering. Results were consistent with the hypothesis that the source of the porosity is a combination of both trapped moisture in the circuit board itself, as well as vaporized flux that is trapped in the molten solder. Other topics investigated include correlation of visual inspection results with joint porosity, pore size measurements, limited pressure effects (0.08 MPa - 0.1 MPa) on the size and number of pores, and joint cooling rate.

Watson, J. Kevin↗
NASA NTRS1997

The Interplay of Surface Mount Solder Joint Quality and Reliability of Low Volume SMAs

Spacecraft electronics including those used at the Jet Propulsion Laboratory (JPL), demand production of highly reliable assemblies. JPL has recently completed an extensive study, funded by NASA's code Q, of the interplay between manufacturing defects and reliability of ball grid array (BGA) and surface mount electronic components.

Spacecraft electronics electronic assemblies J-lea↗
NASA NTRS1982

Shaping Transistor Leads for Better Solder Joints

Special lead-forming tool puts step in leads of microwave power transistors without damaging braze joints that fasten leads to package. Stepped leads are soldered to circuit boards more reliably than straight leads, and stress on brazes is relieved. Lead-forming hand-tool has two parts: a forming die and an actuator. Spring-loaded saddle is adjusted so that when transistor package is placed on it, leads rest on forming rails.

Mandel, H.↗
NASA NTRS1969

Investigation of the development of cracks in solder joints

Study consisted of an analytical approach, in which a mathematical model of existing printed circuit board component mounting techniques was analyzed, and an empirical investigation was performed to determine the extent of damage caused by temperature cycling of the printed circuit boards.

Moore, R. L.↗