SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
K lubricated journal bearings materials friction and wear over temperature range in sliding contact in liquid K and high vacuum
The use of Auger electron spectroscopy (AES) to search for transferred polymer must contend with the fact that there has been no published work on Auger analysis of polymers. Since this is a new area for AES, the Auger spectra of polymers and of halogenated polymers in particular is discussed. It is shown that the Auger spectra of halogenated polymers have certain characteristics that permit an assessment of whether a polymeric transfer film has been established by sliding contact. The discussion is general and the concepts should be useful in considering the Auger analysis of any polymer. The polymers chosen for this study are the halogenated polymers polytetrafluoroethylene (PTFE), polyvinyl chloride (PVC), and polychlorotrifluorethylene (PCTFE).
Multipass sliding friction experiments were conducted with various iron base binary alloys in contact with a single crystal silicon carbide surface in vacuum. Results indicate that the atomic size and concentration of alloy elements play important roles in controlling the transfer and friction properties of iron base binary alloys. Alloys having high solute concentration produce more transfer than do alloys having low solute concentration. The coefficient of friction during multipass sliding generally increases with an increase in the concentration of alloying element. The change of friction with succeeding passes after the initial pass also increases as the solute to iron, atomic radius ratio increases or decreases from unity.
Indenting experiments were conducted with the silicon carbide (0001) surface in contact with a spherical diamond indenter in air. Sliding friction experiments were also conducted with silicon carbide in contact with iron and iron-based binary alloys at room temperature and 800 C. Fracture pits with a spherical particle and spherical wear debris were observed as a result of indenting and sliding. Spherical debris may be produced by a mechanism that involves a spherical-shaped fracture along the circular or spherical stress trajectories under the inelastic deformation zone.
A low friction wear surface with a coefficient of friction in the superlubric regime under a sliding and rolling movement. The low friction wear surface includes molybdenum disulfide and graphene oxide on a first wear surface with a tribolayer formed on a rough steel counter surface during the sliding and rolling movement. Methods of producing the low friction wear surface are also provided.
The development of transfer films atop steel counterfaces in contact with unfilled and bronze-filled PTFE has been studied using X-ray photoelectron spectroscopy. The sliding apparatus was contained within the vacuum of the analytical system, so the effects of the native oxide, hydrocarbon, and adsorbed gaseous surface layers of the steel upon the PTFE transfer behavior could be studied in situ. For both the filled and the unfilled PTFE, cleaner surfaces promoted greater amounts of transfer. Metal fluorides, which formed at the transfer film/counterface interface, were found solely in cases where the native oxide had been removed to expose the metallic surface prior to sliding. These fluorides also were found at clean metal/PTFE interfaces formed in the absence of frictional contact. A fraction of these fluorides resulted from irradiation damage inherent in XPS analysis. PTFE transfer films were found to build up with repeated sliding passes, by a process in which strands of transfer filled in the remaining counterface area. Under these reported test conditions, the transfer process is not expected to continue atop previously deposited transfer films. The bronze-filled composite generated greater amounts of transfer than the unfilled PTFE. The results are discussed relative to the observed increase in wear resistance imparted to PTFE by a broad range of inorganic fillers.
Wear experiments were conducted using replication electron microscopy and reflection electron diffraction to study abrasion and the deformed layers produced in single-crystal Mn-Zn ferrite simulated heads during contact with lapping tapes. The crystaline state of the head is changed drastically during the abrasion process. Crystalline states ranging from nearly amorphous to highly textured polycrystalline can be produced on the wear surface of a single-crystal Mn-Zn ferrite head. The total thickness of the deformed layer was approximately 0.8 microns. This thickness increased as the load and abrasive grit size increased. The anisotropic wear of the ferrite was found to be inversely proportional to the hardness of the wear surface. The wear was lower in the order 211 111 10 0110. The wear of the ferrite increased markedly with an increase in sliding velocity and abrasive grit size.
Plasma-sprayed composites which have good oxidation-resistance and self-lubricating characteristics to 900 C were developed. The composites are a Nichrome matrix containing dispersed glass for oxidation protection and calcium fluoride for lubrication. They are applied to bearing surfaces in layers about 0.050 cm thick by plasma-spraying; the layers are then machined to a thickness of 0.025 cm. Oscillating bearing tests were performed in air to 900 C at unit radial loads up to 3.5 times 10 to the 7th power Newtons per square meter (5000 psi) and a thrust load of 1960 Newtons (440 lb). Bearings with a composite liner in the bore were in good condition after over 50,000 oscillating cycles accumulated during repeated bearing temperature cycles between 25 and 900 C.
Friction and morphological studies were conducted with magnetic tapes containing a Ni-Zn ferrite hemispherical pin in laboratory air at a relative humidity of 40 percent and at 23 C. The results indicate that the binder plays a significant role in the friction properties, morphology, and microstructure of the tape. Comparisons were made with four binders: nitrocellulose; poly (vinyledene) chloride; cellulose acetate; and hydroxyl-terminated, low molecular weight polyester added to the base polymer, polyester-polyurethane. The coefficient of friction was lowest for the tape with the nitrocellulose binder and increased in the order hydroxylterminated, low molecular weight polyester resin; poly (vinyledene) chloride; and cellulose acetate. The degree of enclosure of the oxide particles by the binder was highest for hydroxyl-terminated, low molecular weight polyester and decreased in the order cellulose acetate, poly (vinyledene) chloride, and nitrocellulose. The nature of deformation of the tape was a factor in controlling friction. The coefficient of friction under elastic contact conditions was considerably lower than under conditions that produced plastic contacts.
The present paper describes a transient translating elastoplastic thermomechanical finite element model to study two-dimensional frictional rolling contact. Frictional two-dimensional contact is simulated by repeatedly translating a nonuniform thermomechanical distribution across the surface of an elastoplastic half space. The half space is represented by a two-dimensional finite element mesh with appropriate boundaries. Calculations are for an elastic-perfectly plastic material and the selected thermophysical properties are assumed to be temperature independent. The paper presents temperature variations, stress and plastic strain distributions and deformations. Residual tensile stresses are observed. The magnitude and depth of these stresses depends on (1) the temperature gradients and (2) the magnitudes of the normal and tangential tractions.
Low speed Ga lubricated sliding electrical contacts of Be in vacuum, discussing Ga film role in friction and contact resistance
The results of research programs to develop sliding electrical contact materials, both brushes and slip rings, are discussed. Problems attendant to operating sliding contacts in a vacuum are defined; limitations of commercial materials in solving these problems are described, and special materials and surface finish conditions which have resulted in solutions to these problems are presented. Data from operational tests on the newly developed materials are compared with similar data obtained from materials now used as standards in consumer products. Possible commercial applications of the more efficient sliding contact materials are discussed briefly.
Reducing friction and contact resistance of sliding electrical contacts of beryllium by gallium lubrication in vacuum
Sliding electrical contacts for unmanned scientific satellites, discussing Nimbus AVCS camera iris motors
The ferrograph was used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness. Essentially all of the generated wear particles were of the normal rubbing wear type.
Sliding friction experiments were conducted with manganese-zinc ferrite (100), (110), (111), and (211) planes in contact with themselves. Mating the highest-atomic-density directions, (110), of matched crystallographic planes resulted in the lowest coefficients of friction. Mating matched (same) high-atomic-density planes and matched (same)crystallographic directions resulted in low coefficients of friction. Mating dissimilar crystallographic planes, however, did not give significantly different friction results from those with matched planes. Sliding caused cracking and the formation of hexagonal- and rectangular-platelet wear debris on ferrite surfaces, primarily from cleavage of the (110) planes.
The Ferrograph has been used to analyze wear debris generated in a sliding elastohydrodynamic contact. The amount of wear debris correlates well with the ratio of film thickness to composite surface roughness (Lambda ratio). Essentially all of the generated wear particles were of the normal rubbing wear type.
In this study, moving surface temperature measurements in rolling and sliding EHD point contacts were made using an available infrared technique. Film thickness and traction have also been measured. Slide-to-roll ratios of -2 to +2 have been studied. By using a different kinematic configuration, stationary surface temperatures have also been measured. It has been shown that, while surface temperature rises in the low slip region are relatively small, stationary surface temperatures are significantly higher than the moving surface temperatures. Flash temperature theory has been extended to cover the combined rolling and sliding conditions. Correlation between the predicted and the measured values has also been performed.