SEARCH · Engineering Papers
Results for “SINTERING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Reactive flash sintering of the entropy-stabilized oxide Mg0.2Ni0.2Co0.2Cu0.2Zn0.2O
Explore the source record for details and available documents.
Scaling microstructural processes in the sintering of ionic ceramics
A multi-scale framework, combining a multiphase field formulation and large deformation mechanics, was developed as a stepping stone to perform the data analytics of the microstructural level kinetics of a sintering solid. Relevant microstructural information from this framework, such as grain, stress, and porosity statistics, was scaled up to describe the macroscopic level sintering kinetics. Here, the developed formulation was applied to describe the electric field assisted sintering of Y 2 O 3 . Microstructural inhomogeneities in a multi-granular solid result in the formation of a field of compressive stress networks, which interleave with low compression and weakly tensile regions, defining a scaffolding for sintering concentration regions to develop. A Poisson effect-induced lateral stress network is also naturally self-induced as a result of the mechanical constraints imposed by the sintering apparatus. For long sintering times, localized shear stresses enhancing mass flow along grain boundaries and internal surfaces develop. Three-sided pores are removed by either vacancy transport to the surrounding pores, or move towards the external surfaces through grain boundary diffusion. Four- and higher order-sided pores stabilize because an equal amount of vacancies are gained and lost through the connecting grain boundaries. Grain dewetting contributes to pore coalescence, suggesting that pore kinetics and grain growth are coupled and should be analyzed in concert. The combined sintering and grain growth kinetics define six regimes of sintering behavior: (1) T, the transient regime; (2) E$_Υ$, the surface energy dominated, early sintering regime, where the grain growth exponent, p = 1, and the stress concentration factor, $f$ ~ $1/\hat{ρ}^{4.6}$; (3) E S , the stress dominated, early sintering regime, where p = 1 and $f$ ~ $1/\hat{ρ}^{4}$; (4) I$_Υ$, the surface energy dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4.6}$; (5) I S , the stress dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4}$; and (6) L, the late sintering regime, where p = 3 and $f$ ~ 1. At the macroscopic level, the rapid densification and suppression of grain growth observed in the electric field assisted sintering process is a consequence of the compounding effects of the underlying stress-, transport-, and interfacial-energy-induced energy minimization kinetics, as predicted by the multi-scale framework.
Gravitational Effects on Distortion in Sintering
During sintering a powder compact gains strength through low-temperature interparticle bonding, usually induced by solid-state surface diffusion, followed by further strength contributions from high-temperature densification. In cases where a liquid phase forms, sintering densification is accelerated and shape retention is sustained while open pores remain and contribute capillary forces. Unfortunately, sintering densification requires the compact become thermally softened to a point where creep strain rates reach levels near 10(exp -2)/s when the liquid forms. On the other hand, thermal softening of the powder compact substantially reduces the strength at high temperatures. Therefore, the in situ strength evolution during sintering is a primary focus to separate compact densification (as required for high performance) with minimized distortion (as required for net-shaping). With respect to gravitation effects on distortion during sintering there are two points of substantial weakness - prior to significant interparticle bonding and during final pore closure. This research is focused on understanding the competition among interparticle neck growth, densification, thermal softening, grain boundary wetting, capillary effects associated with liquid wetting and residual porosity, and gravity. Most surprising is the apparent role of gravity, where the deviatoric stress acting on the powder structure induces skeletal formation that reduces distortion. In contrast with theory, microgravity samples exhibit more distortion yet fail to fully densify. Results are presented on the experimental concepts supporting an emerging model of sintering strength evolution that enables understanding of both distortion and densification. The experiments have relied on tungsten heavy alloys, various combinations of dihedral angle, pore size, initial porosity, liquid:solid ratio, and heating rates. On Earth, the dominant factor with respect to distortion is the starting body heterogeneity. Current modeling efforts are seeking some means to uniformly predict the distortion based on a starting pore structure heterogeneity parameter. Densification is largely unaffected by the initial pore structure, but distortion is highly variable, suggesting that nonuniform pore closure might be a significant parameter during sintering. With respect to flight experiments, plans include removal of the solid body forces acting on the solid grains, allowing stabilization of the pore structure and examination of the buoyancy effects with regard to distortion. In microgravity there is the surprising result that compacts do not densify, yet distort a factor that is contrary to all current sintering models. Densification without distortion during liquid phase sintering was achieved by manipulating microstructure and its evolution during sintering. Microstructure parameters such as the solid volume fraction, dihedral angle, initial porosity, and pore size were varied to measure densification and distortion behavior during LPS using W-Ni-Cu alloys. Green compacts were formed using ethylene-bis-stearamide as a pore-forming agent with the amount of polymer controlling the initial porosity. Different initial pore sizes were generated by varying the polymer particle size. Dihedral angle was varied by changing the Ni:Cu ratio in the alloys. Finally, the solid volume fraction was adjusted via the tungsten content. Distortion was quantified using profiles determined with a coordinate measuring machine to calculate a distortion parameter. Sintering results showed that solid volume fraction and dihedral angle are the dominant factors on densification and distortion during liquid phase sintering. Distortion decreases with increasing solid volume fraction and dihedral angle, while initial porosity and pore size have no observable effect on distortion at nearly full densification. Various strategies emerge to improve distortion control in liquid phase sintering.
A Rapid Sintering Method for Cerium Nitride Pellet: A Uranium Mononitride Surrogate
Uranium mononitride (UN) is a candidate fuel material for light water reactors with higher uranium (U) loading and thermal conductivity than uranium dioxide (UO 2 ). However, the sintering of UN pellets is challenging as the UN powder particles oxidize rapidly at high temperatures unless the oxygen concentration is extremely low. Oxidation during sintering either reduces the relative density of the sintered UN pellet or disintegrates the sintered UN pellet to powder. To address this problem, the present work developed a rapid sintering method for producing highly densified UN surrogate pellets with minimal oxidation. Cerium nitride (CeN) is used as a surrogate for UN to reduce radiation hazards. With the custom-developed fast-heating system, the sintering process was completed within 150 s. The sintering atmosphere was flowing nitrogen (N 2 ). The sintered CeN pellet density was 95% of the theoretical density (TD) or higher. The microstructure was uniform with a 10–25 µm grain size as demonstrated by scanning electron microscopy (SEM) and contained trivial levels of oxides as demonstrated by X-ray diffraction (XRD). The resultant pellets indicate that the rapid sintering method is a promising method to make UN fuel pellets with equivalent or higher density to pellets made by conventional sintering methods, while also being more efficient in time and costs.
Multi-material direct ink writing and co-sintering of gadolinium oxide – zirconium oxide components
Methods for fabrication of multi-material or functionally graded ceramic composite architectures are of interest for numerous applications. However, conventional co-sintering of multi-material ceramic parts is a challenge because differences in the sintering behavior of the two materials leads to interfacial strain and, ultimately, component failure. Direct ink writing (DIW) is an extrusion-based additive manufacturing process that excels at multi-material printing because multiple extrusion nozzles can be installed on the same gantry system. Furthermore, the use of DIW as a method to fabricate multi-material ceramic green bodies offers an additional variable for controlling and potentially matching sintering kinetics in the slurry formulation used for two dissimilar feedstocks. In the work documented in this manuscript, we explored two strategies to successfully co-sinter multi-material ceramic oxides: slurry optimization to match sintering kinetics and material gradients to step from one material to another. This manuscript also quantifies the allowable mismatch that avoids part cracking in solid solution forming multi-material systems and discusses best strategies to reduce mismatch during co-sintering. Inks composed of gadolinium oxide (Gd 2 O 3 ) and zirconium oxide (ZrO 2 ), a surrogate for uranium oxide (UO 2 ), were thermally matched, which resulted in a sintering mismatch reduction of over 10%. It was found that ~1% mismatch is tolerable during debind cycles and that ~5% mismatch is manageable during sintering cycles after slurry formulations are optimized to match the sintering behavior. Use of continuous gradients is shown to reduce sintering mismatch, although geometric resolution may be lost due to solid solution formation.
A Lamination Model for Pressure-Assisted Sintering of Multilayered Porous Structures
This work describes a lamination model for pressure-assisted sintering of thin, multilayered, and porous structures based on the linear viscous constitutive theory of sintering and the classical laminated plate theory of continuum mechanics. A constant out-of-plane normal stress is assumed in the constitutive relation. The lamination relations between the force/moment resultants and the strain/curvature rates are presented. Numerical simulations were performed for a symmetric tri-layer laminate consisting of a 10% gadolinia doped ceria (Ce 0.9 Gd 0.1 O 1.95-δ ) composite structure, where porous layers were adhered to the top and bottom of a denser layer under uniaxially-applied pressures and the sinter forging conditions. The numerical results show that, compared with free sintering, the applied pressure can significantly reduce the sintering time required to achieve given layer thicknesses and porosities. Unlike free sintering, which results in a monotonic decrease of the laminate in-plane dimension, pressure-assisted sintering may produce an in-plane dimension increase or decrease, depending on the applied pressure and sintering time. Finally, the individual layers in the laminate exhibit different stress characteristics under pressure-assisted sintering.
Effects of mechanically alloying Al 2 O 3 and Y 2 O 3 additives on the liquid phase sintering behavior and properties of SiC
In order to improve the sintering of SiC, mixtures of Al 2 O 3 and Y 2 O 3 powders are commonly included as sintering additives. The aim of this work was to use mechanically alloyed Al 2 O 3 –Y 2 O 3 mixtures as sintering additives to promote liquid phase sintering of SiC using spark plasma sintering. The results showed that milling reduced the particle size of the powders and led to the formation of complex oxide phases (YAP, YAM, and YAG) at low temperatures. As the ball milling time increased, the mass loss of specimens sintered with mechanically alloyed Al 2 O 3 –Y 2 O 3 mixtures decreased, and accordingly the relative density increased. However, the hardness and flexural strength of sintered SiC specimens first increased and then decreased. Because the specimens prepared with oxides milled for a long time contained too much YAG/YAP and accordingly too much liquid at sintering temperature. This negatively affected the mechanical properties of the SiC specimens because of the increased volume of the complex oxide phases, which have inferior mechanical properties to SiC, in the sintered specimens. In conclusion, when the ball milling time was 6h, the hardness (24.02 GPa) and flexural strength (655.61 MPa) of the SiC specimens reached maximum values.
Machine learning-assisted ultrafast flash sintering of high-performance and flexible silver–selenide thermoelectric devices
Flexible thermoelectric generators (TEGs) have shown immense potential for serving as a power source for wearable electronics and the Internet of Things. A key challenge preventing large-scale application of TEGs lies in the lack of a high-throughput processing method, which can sinter thermoelectric (TE) materials rapidly while maintaining their high thermoelectric properties. Herein, we integrate high-throughput experimentation and Bayesian optimization (BO) to accelerate the discovery of the optimum sintering conditions of silver–selenide TE films using an ultrafast intense pulsed light (flash) sintering technique. Due to the nature of the high-dimensional optimization problem of flash sintering processes, a Gaussian process regression (GPR) machine learning model is established to rapidly recommend the optimum flash sintering variables based on Bayesian expected improvement. For the first time, an ultrahigh-power factor flexible TE film (a power factor of 2205 μW m -1 K -2 with a zT of 1.1 at 300 K) is demonstrated with a sintering time less than 1.0 second, which is several orders of magnitude shorter than that of conventional thermal sintering techniques. Further, the films also show excellent flexibility with 92% retention of the power factor (PF) after 10 3 bending cycles with a 5 mm bending radius. In addition, a wearable thermoelectric generator based on the flash-sintered films generates a very competitive power density of 0.5 mW cm -2 at a temperature difference of 10 K. This work not only shows the tremendous potential of high-performance and flexible silver–selenide TEGs but also demonstrates a machine learning-assisted flash sintering strategy that could be used for ultrafast, high-throughput and scalable processing of functional materials for a broad range of energy and electronic applications.
Ultra–fast, selective, non–melting, laser sintering of alumina with anisotropic and size–suppressed grains
In this paper, we report an ultra-fast sintering phenomenon of alumina achieved by the scanning laser irradiation method. Using CO 2 laser irradiation, we found that micrometer-sized alumina powder (d 50 = 1.2 µm) can be sintered close to full density within a few tens of seconds. The microstructure of laser-sintered alumina was different from that of the furnace-sintered alumina. The relative density and grain size of the laser-sintered alumina gradually decreased from the center of the laser beam to the edge. Anisotropy of the grain size was measured along and perpendicular to the scanning direction. This anisotropy decreased as the scanning speed decreased from 0.1 mm/s to 0.01 mm/s. The sintering master curve of grain size versus relative density, which reflects the sintering mechanism, was found to be affected by the laser scanning speed. When the laser scanning speed was 0.1 mm/s, grain size suppression was found for the almost fully dense alumina. However, at lower scanning speed (e.g., 0.01 mm/s), there was significant grain growth in the regions where the relative density was greater than 90%. Furthermore, these results clearly indicate that alumina can be sintered, in the solid-state, to a high density in a short time using scanning laser and the microstructure is different from the furnace-sintered alumina.
Sintering of lunar glass and basalt
Experiments were conducted to study the sintering behavior of glass and basalt lunar soil simulants. The degree of sintering was assessed by compressive strength testing and microanalysis. Both crushed glass and basalt sinter significantly at 1000 C, with the basalt attaining its maximum strength at 1100 C. Initial sintering occurs in less than 15 min, and the degree of sintering does not increase significantly with time after about 30 min. Glass sinters more readily than crystalline material. Sintering and devitrification both occur on a time scale of minutes in the heated glass, but sintering is apparently more rapid. The processes of sintering and oxygen release by hydrogen reduction of lunar soil are synergistic, and could be combined to produce two extremely useful products at a lunar base.
Process Developed for Generating Ceramic Interconnects With Low Sintering Temperatures for Solid Oxide Fuel Cells
Solid oxide fuel cells (SOFCs) have been considered as premium future power generation devices because they have demonstrated high energy-conversion efficiency, high power density, and extremely low pollution, and have the flexibility of using hydrocarbon fuel. The Solid-State Energy Conversion Alliance (SECA) initiative, supported by the U.S. Department of Energy and private industries, is leading the development and commercialization of SOFCs for low-cost stationary and automotive markets. The targeted power density for the initiative is rather low, so that the SECA SOFC can be operated at a relatively low temperature (approx. 700 C) and inexpensive metallic interconnects can be utilized in the SOFC stack. As only NASA can, the agency is investigating SOFCs for aerospace applications. Considerable high power density is required for the applications. As a result, the NASA SOFC will be operated at a high temperature (approx. 900 C) and ceramic interconnects will be employed. Lanthanum chromite-based materials have emerged as a leading candidate for the ceramic interconnects. The interconnects are expected to co-sinter with zirconia electrolyte to mitigate the interface electric resistance and to simplify the processing procedure. Lanthanum chromites made by the traditional method are sintered at 1500 C or above. They react with zirconia electrolytes (which typically sinter between 1300 and 1400 C) at the sintering temperature of lanthanum chromites. It has been envisioned that lanthanum chromites with lower sintering temperatures can be co-fired with zirconia electrolyte. Nonstoichiometric lanthanum chromites can be sintered at lower temperatures, but they are unstable and react with zirconia electrolyte during co-sintering. NASA Glenn Research Center s Ceramics Branch investigated a glycine nitrate process to generate fine powder of the lanthanum-chromite-based materials. By simultaneously doping calcium on the lanthanum site, and cobalt and aluminum on the chromium site, we could sinter the materials below 1400 C. The doping concentrations were adjusted so that the thermal expansion coefficient matched that of the zirconia electrolyte. Also, the investigation was focused on stoichiometric compositions so that the materials would have better stability. Co-sintering and chemical compatibility with zirconia electrolyte were examined by X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy (line scanning and dot map). The results showed that the materials bond well, but do not react, with zirconia electrolyte. The electric conductivity of the materials measured at 900 C in air was about 20 S/cm.
Sinter formation during directed energy deposition of titanium alloy powders
During directed energy deposition (DED) additive manufacturing, powder agglomeration and sintering can occur outside of the melt pool when using titanium alloy powders. Using in situ synchrotron radiography we investigate the mechanisms by which sintering of Ti6242 powder occurs around the pool, performing a parametric study to determine the influence of laser power and stage traverse speed on sinter build-up. The results reveal that detrimental sinter can be reduced using a high laser power or increased stage traverse speed, although the latter also reduces deposition layer thickness. The mechanism of sinter formation during DED was determined to be in-flight heating of the powder particles in the laser beam. Calculations of particle heating under the processing conditions explored in this study confirm that powder particles can reasonably exceed 700 °C, the threshold for Ti surface oxide dissolution, and thus the powder is prone to sintering if not incorporated into the melt pool. The build-up of sinter powder layer on deposit surfaces led to lack of fusion pores. To mitigate sinter formation and its detrimental effects on DED component quality, it is essential that the powder delivery spot area is smaller than the melt pool, ensuring most powder lands in the melt pool.
In-situ synchrotron X-ray diffraction of hydroxyapatite-zirconia composite during conventional and flash sintering
Here, we conducted in-situ X-ray diffraction to study the crystalline phase evolution in hydroxyapatite-zirconia composites during both conventional and flash sintering processes. Additionally, we examined the thermal history and microstructure of the composite under these sintering conditions. Despite both sintering methods reaching similar average temperatures, they yielded distinct results in terms of crystalline phase composition and microstructure. In the flash sintered samples, we observed a complete transformation of hydroxyapatite into α- tricalcium phosphate and a complete tetragonal to cubic phase transition in zirconia. Conversely, the conventionally sintered samples remained practically stable. Notably, the flash sintered samples exhibited needle-like microstructures, which were absent in their conventionally sintered counterparts. This divergence suggests that the application of an electric field plays a role in generating athermal effects during the sintering of hydroxyapatite-zirconia composites.
Effect of sintering temperature on feature resolution and flexural strength of ceramics fabricated through vat photopolymerization additive manufacturing
Although ceramic additive manufacturing (AM) could be used to fabricate complex, high-resolution parts for diverse, functional applications, one ongoing challenge is optimizing the post-process, particularly sintering, conditions to consistently produce geometrically accurate and mechanically robust parts. This study aims to investigate how sintering temperature affects feature resolution and flexural properties of silica-based parts formed by vat photopolymerization (VPP) AM. Test artifacts were designed to evaluate features of different sizes, shapes and orientations, and three-point bend specimens printed in multiple orientations were used to evaluate mechanical properties. Sintering temperatures were varied between 1000°C and 1300°C. Deviations from designed dimensions often increased with higher sintering temperatures and/or larger features. Higher sintering temperatures yielded parts with higher strength and lower strain at break. Many features exhibited defects, often dependent on geometry and sintering temperature, highlighting the need for further analysis of debinding and sintering parameters. To the best of the authors’ knowledge, this is the first time test artifacts have been designed for ceramic VPP. This work also offers insights into the effect of sintering temperature and print orientation on flexural properties. These results provide design guidelines for a particular material, while the methodology outlined for assessing feature resolution and flexural strength is broadly applicable to other ceramics, enabling more predictable part performance when considering the future design and manufacture of complex ceramic parts.
Controlled current-rate AC flash sintering of uranium dioxide
Uranium dioxide (UO2) pellets with controlled microstructures were densified up to 93.4% of their theoretical density in less than 25 minutes at a furnace temperature of 873 K, utilizing controlled current-rate alternating current (AC) flash sintering (FS). Using this AC-FS method it was possible to control the sintering rate and thermal gradients, resulting in dense pellets with no appreciable hourglassing and good mechanical integrity. Moreover, the apparent sintering activation energy for FS and for conventionally sintered samples was estimated to be 108 kJ mol -1 and 380 kJ mol -1 , respectively using the master sintering curve method. The apparent activation energy for FS was remarkably close to those reported in the literature for spark plasma sintering of UO 2 . Furthermore, both these field assisted sintering methods utilize fast heating rates and electrical effects that are likely enhancing the grain boundary diffusion mechanism. Finally controlled current-rate AC-FS has been demonstrated as a technological advancement, capable of producing ceramic nuclear fuels in a fraction of the conventional processing time.
In-operando synchrotron experiments of flash sintering carried out in current rate mode
Here, we report first-time results for in-operando flash sintering synchrotron experiments carried out in current rate mode where the specimen, held at a constant temperature, is fed current that is increased at a constant rate. These experiments are unique because the time dependence of the sintering behavior can be stretched out over a longer period (by changing the current rate) than in voltage-to-current experiments in which sintering occurs in a burst at the onset of the flash. Two results are presented: (i) A comparison of temperatures measured with the platinum standard to those predicted by the black body radiation model leading to estimates of the emissivity as a function of porosity whereby emissivity increases from 0.65 to 0.9 as the sample sinters from its green state to full density, and (ii) measurements of the excess lattice expansion as a function of density as the sample sinters continuously while the current is increased. The present work highlights the promise of current rate experiments to obtain results while the sample sinters gradually from its green density to full density (somewhat akin to conventional sintering) for gaining further insights into the mechanisms of flash sintering.
Development of Binder Jet Compatible Silicon Carbide Mixtures for Increased Sintered Density
Binder jet additive manufacturing can process a variety of ceramic powder feedstocks to manufacture near net shape green parts that are subsequently sintered to achieve densification. In particular, silicon carbide (SiC) is a promising ceramic material for heat exchangers in energy storage applications and binder jet is a well-suited process for manufacturing these heat exchangers due to the often geometrically complex designs. However, the need for good powder flowability in binder jet printing often limits the feedstock powder to be larger particles rather than that of ultra fine submicron powders used in conventional ceramic processing, which are more readily densified during sintering. The present work explores the use of various powder mixtures and sintering settings to identify strategies for achieving high density sintered parts in binder jet compatible systems without the use of infiltration. Liquid-phase sintering additives and bimodal powder mixtures are explored alongside different sintering temperatures, rates, atmospheres, and hold times. Two mixtures were found to be good candidates for further exploration: 1) 90 wt% 0.6 µm SiC + 6.25 wt% Al 2 O 3 + 3.75 wt% Y 2 O 3 mixture achieved the highest sintered relative density of 91.2%; and 2) a bimodal mixture comprised of 45 wt% 10 µm SiC + 45 wt% 0.6 µm SiC + 6.25 wt% Al 2 O 3 + 3.75 wt% Y 2 O 3 had the best powder flowability of the powders measured and a 75.1% sintered relative density.