SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A self-lubricating, friction and wear reducing composite material is described for use over a wide temperature spectrum from cryogenic temperature to about 900 C in a chemically reactive environment comprising silver, barium fluoride/calcium fluoride eutectic, and metal bonded chromium carbide.
The advantages and disadvantages of elemental silver as a tribological material are discussed. It is demonstrated that the relatively high melting point of 961 deg C, softness, marked plasticity, and thermochemical stability of silver combine to make this metal useful in thin film solid lubricant coatings over a wide temperature range. Disadvantages of silver during sliding, except when used as a thin film, are shown to be gross ploughing due to plastic deformation under load with associated high friction and excessive transfer to counterface surfaces. This transfer generates an irregular surface topography with consequent undesirable changes in bearing clearance distribution. Research to overcome these disadvantages of element silver is described. A comparison is made of the tribological behavior of pure silver with that of silver formulated with other metals and high-temperature solid lubricants. The composite materials are prepared by co-depositing the powdered components with an airbrush followed by furnace heat treatment or by plasma-spraying. Composite coatings were formulated which are shown to be self-lubricating over repeated, temperature cycles from low temperature to about 900 deg C.
Criteria are discussed for predicting the probable lubricating ability of candidate solid materials from a consideration of their basic chemical and physical properties. The properties considered to be important in the model are thermochemical potential, adhesion, low hardness, plasticity, yield strength in shear, and brittle-to-ductile transition characteristics. A review of the selection and tribological testing of materials, which were selected for use in self-lubricating composite coatings by employing this model, is given. Two series of plasma-sprayed coatings with good tribological properties over a wide temperature spectrum are described. The PS 100 series of coatings contain oxidatively stable solid lubricants in a nichrome matrix. The PS 200 series contains the same solid lubricants in a very wear resistant metal-bonded chromium carbide matrix. Examples are given of applications of these coatings in high speed shaft seals, sliding contact bearings, and Stirling engine cylinder liners.
The advantages and disadvantages of elemental silver as a tribological material are discussed. It is demonstrated that the relatively high melting point of 961 deg C, softness, marked plasticity, and thermochemical stability of silver combine to make this metal useful in thin film solid lubricant coatings over a wide temperature range. Disadvantages of silver during sliding, except when used as a thin film, are shown to be gross ploughing due to plastic deformation under load with associated high friction and excessive transfer to counterface surfaces. This transfer generates an irregular surface topography with consequent undesirable changes in bearing clearance distribution. Research to overcome these disadvantages of element silver is described. A comparison is made of the tribological behavior of pure silver with that of silver formulated with other metals and high-temperature solid lubricants. The composite materials are prepared by co-depositing the powdered components with an airbrush followed by furnace heat treatment or by plasma-spraying. Composite coatings were formulated which are shown to be self-lubricating over repeated, temperature cycles from low temperature to about 900 deg C.
A composite material is described which will provide low friction surfaces for materials in rolling or sliding contact and is self-lubricating and oxidation resistant up to and in excess of about 930 C. The composite is comprised of a metal component which lends strength and elasticity to the structure, a fluoride salt component which provides lubrication and, lastly, a glass component which not only provides oxidation protection to the metal but may also enhance the lubrication qualities of the composite.
In the early 1980's, Lewis Research Center began a program to develop high-temperature lubricants for use on future aircraft flying at three or more times the speed of sound, which can result in vehicle skin temperatures as high as 1,600 degrees Fahrenheit. A material that emerged from this research is a plasma-sprayed, self-lubricating metal- glass-fluoride coating able to reduce oxidation at very high temperatures. Technology is now in commercial use under the trade name Surf-Kote C-800, marketed by Hohman Plating and Manufacturing Inc. and manufactured under a patent license from NASA. Among its uses are lubrication for sliding contact bearings, shaft seals for turbopumps, piston rings for high performance compressors and hot glass processing machinery; it is also widely used in missile and space applications.
An improved bearing structure is described which includes a permanently magnetized porous body filled with an interstitial magnetic lubricant for extending the operational life of self-lubricating bearings. The bearing structure is characterized by a permanently magnetized retainer formed of a porous material and filled with an interstitial magnetic lubricant, whereby the pores serve as lubricant reservoirs from which the lubricant continuously is delivered to a film disposed between contiguous bearing surfaces.
Topics addressed include: aeropropulsion research and technology impact; high temperature polymer matrix composites; creep and fatigue effects; self-lubricating coatings; and ceramics for engines.
This paper describes new compositions of self-lubricating coatings that contain chromium carbide. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The coating constituents were treated as a ternary system consisting of: (1) the bonded carbide base material, (2) silver, and (3) the eutectic. A study to determine the optimum amounts of each constituent was performed. The various compositions were prepared by powder blending. The blended powders were then plasma sprayed onto superalloy substrates and diamond ground to the desired coating thickness. Friction and wear studies were performed at temperatures from 25 to 760 C in helium and hydrogen. A variety of counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications such as piston ring/cylinder liner couples for Stirling engines.
This paper describes new compositions of self-lubricating coatings that contain chromium carbide. A bonded chromium carbide was used as the base stock because of the known excellent wear resistance and the chemical stability of chromium carbide. Additives were silver and barium fluoride/calcium fluoride eutectic. The coating constituents were treated as a ternary system consisting of: (1) the bonded carbide base material, (2) silver, and (3) the eutectic. A study to determine the optimum amounts of each constituent was performed. The various compositions were prepared by powder blending. The blended powders were then plasma sprayed onto superalloy substrates and diamond ground to the desired coating thickness. Friction and wear studies were performed at temperatures from 25 to 760 C in helium and hydrogen. A variety of counterface materials were evaluated with the objective of discovering a satisfactory metal/coating sliding combination for potential applications such as piston ring/cylinder liner couples for Stirling engines.
Load capacities were determined for plain spherical bearings with self-lubricating spherical elements of graphite-fiber-reinforced-polyimide, and for plain cylindrical bearings with thin-wall liners of the composite in the bearing bores. Composites consisted of a 1-to-1 weight ratio of graphite fibers and polyimide. Oscillation was at an amplitude of + or - 15 deg at a frequency of 1 hertz. Bearings with composite ball material had a load capacity of approximately 69 MN/sq m (10 000 psi) at room temperature 25 MN/sq m (3600 psi) at 340 C (650 F). Bearings with thin-wall composite liners had much higher load capacities of 280 MN/sq m (40 000 psi) at room temperature amd 240 MN/sq m (35 000 psi) at 320 C (600 F). Friction coefficients were in the range of 0.12 to 0.19. The addition of 10 wt.% graphite fluoride solid lubricant to the composition of the thin-wall liners reduced friction coefficients into the range of 0.10 to 0.12.
Reinforced FEP Teflon composite material is bonded to a metal substrate by applying a thin layer of copper on the metal surface and disposing irregularly shaped copper particles on the coated surface. The reinforced Teflon is then assembled in contact with the particles, and the assembly is heated under pressure at an elevated temperature below the melting point of the Teflon. A diffusion bond stronger than the reinforced Teflon component is produced, thus enabling the fabrication of self-lubricating bodies with relatively high strength.
Some present-day aeropropulsion systems impose severe demands on the thermal and oxidative stability of lubricant, bearing, and seal materials. These demands will be much more severe for operational systems around the turn of the century. Solid lubricants with maximum temperature capabilities of about 1100 C are known. Unfortunately, none of the solid lubricants with the highest temperature capabilities are effective below approximately 400 C. However, research shows that silver and stable fluorides, such as calcium and barium fluoride act synergistically to provide lubrication from below room temperature to approximately 900 C. Plasma-sprayed, self-lubricating composite coatings that were developed at Lewis are described. Background information is given on coatings, designed as PS100 and PS101, that contain the solid lubricants in a Nichrome matrix. These coatings have low friction coefficients over a wide temperature range, but they have inadequate wear resistance for some long-duration applications. Wear resistance was dramatically improved in a recently developed coating PS200, by replacing the Nichrome matrix material with metal-bonded chromium carbide containing dispersed silver and calcium fluoride/barium fluoride eutectic (CaF2/BaF2). The lubricants control friction and the carbide matrix provides excellent wear resistance. Successful tests of these coatings are discussed.
At one time, solid lubricants were used almost entirely in aerospace applications. Today there is a pronounced trend to use them over a much broader range of applications. For example, self-lubricating polymer-based composites have displaced traditional oil-lubricated, metallic composites for many journal bearings and thrust, washers in applications as diverse as earthmoving machinery and snow blowers to aircraft applications. For moderate temperatures below 200° C, glass filament-wound epoxy bearings with PTFE lubricating liners are useful; for temperatures up to 350° C, graphite fiber reinforced polyimide bearing materials are finding applications. Molybdenum disulfide, graphite, and PTFE are the most widely known and used solid lubricants, and there is increasing interest in the relatively new solid lubricant graphite fluoride. Advanced technology engines such as the adiabatic diesel and the small, efficient gas turbine have severe lubrication and wear problems at temperatures beyond the capabilities of any of these lubricants. Here, self-lubricating ceramics and inorganic composites for use at I000° C or higher are of interest. However, perhaps the most significant new direction for solid lubricant coatings and self-lubricating composites is their steadily increasing use in dry bearings for large volume, moderate temperature applications. This can be attributed to their simplicity of use (no supporting lubricant system needed), light weight, convenience, and general cost effectiveness.
Composite gear configuration provides a reliable automatic means for replenishing gear mechanism lubricants that dissipate in the harsh environment of space. The center or hub section of the gear consists of a porous, oil impregnated material, and the outer or toothed section has radially drilled passages to cause the oil to gradually flow to the gear teeth surface.
Self-lubricating gear, designed for long term operation in a vacuum at high, low, and ambient temperatures, is constructed of alternating layers of metal and a dry lubricant material, such as polytetrafluoroethylene, with a suitable reinforcing material bonded into a laminated composite unit, which is machined to form a standard gear.
Recent research at NASA-Lewis on solid lubricants for use at high temperatures in air and other gaseous environments is presented. The characteristics of oxide and fluoride lubricants at temperatures to 1700 F are described. Data is presented for fluoride coatings with silicate and other additives incorporated to give improved wear life and better oxidation protection to the substrate metal. Experience is described for fluoride-metal self-lubricating composites with improved metal oxidation resistance to 1700 F. The concept of cast, self-lubricating ceramics is also explored.
One of the most important criterion for acceptable commercial application of a multiple phase composition is uniformity and reproducibility. This means that the performance characteristics of the coat - e.g., its lubricating properties, bond strength to the substrate, and thermal properties - can be readily predicted to give a desired performance. The improvement of uniformity and reproducibility of the coats, the oxidation behavior at three temperature ranges, the effect of bond coat and the effect of preheat treatment as measured by adhesive strength tests, coating examination procedures, and physical property measurements were studied. The following modifications improved the uniformity and reproducibility: (1) changes and closer control in the particle size range of the raw materials used, (2) increasing the binder content from 3.2% to 4.1% (dried weight), and (3) analytical processing procedures using step by step checking to assure consistency.