SEARCH · Engineering Papers
Results for “Renewables”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Sizing Energy Storage Systems to Mitigate Variability of Renewable Generation for Grid Stability using Inverse Uncertainty Propagation
Explore the source record for details and available documents.
A Novel Catalytic Membrane Reactor for DME Synthesis from Renewable Resources
Production of liquid fuels or chemicals from CO 2 (captured from the air or flue gases) and renewable hydrogen presents a new approach to producing clean fuels domestically. While significant progress has been made in the area of renewable electricity generation from solar and wind, a large gap remains with respect to the production of renewable liquid fuels/chemicals. Other processes for producing liquid fuels/chemicals from renewable electricity are constrained by thermodynamic limitations, making them prohibitively expensive and impractical. The team is overcoming these limitations and developing catalytic membrane reactor processes with high yields and low energy penalties. Supported by the Advanced Research Projects Agency-Energy (ARPA-E) of the US Department of Energy (DOE), GTI Energy and partners have been developing a technology for the production of renewable dimethyl ether (DME) from carbon dioxide (CO 2 ) and renewable hydrogen (H 2 ) using a novel catalytic membrane reactor and demonstration of this system at a scale of 1 kg/day. DME is a clean-burning, non-toxic fuel with a high cetane value (55-60), making it an excellent diesel alternative. DME can be stored as a liquid under moderate pressure, eliminating the need for the high-pressure containers used for CNG or cryogenics, as in the case of LNG. DME is also approved as a renewable fuel under the U.S. Environmental Protection Agency’s Renewable Fuels Standard (RFS), making it eligible for Renewable Identification Numbers (RINs) credits. By producing DME through the catalytic conversion of captured CO 2 and renewable H 2 , this process will produce renewable liquid transportation fuel and a means of large-scale utilization of captured CO 2 . In the DME synthesis process, CO 2 and H 2 are fed to a hollow fiber catalytic membrane reactor at 300-600 psig that contains a bi-functional catalyst that combines two reactions, methanol synthesis (CO 2 + 3H 2 → CH 3 OH + H 2 O) and methanol dehydration (2CH 3 OH → CH 3 OCH 3 + H 2 O), into a one-step process to produce DME. The bifunctional catalyst converts methanol to DME, enabling higher overall CO 2 conversion. A Cu/ZnO/ZrO 2 /Al 2 O 3 (CZZA) catalyst is used for methanol synthesis and is coupled with a zeolite catalyst H-ZSM-5 for dehydration. This one-step process intensifies a process that would otherwise require multiple reaction steps. However, combining these two reactions results in increased water production which inhibits catalytic activity. Here, the Na + -gated, water-transport membrane (Science, vol. 367, pp. 667, 2020), removes water in situ, shifting the thermodynamic equilibrium towards product formation while decreasing kinetic inhibition from water adsorption onto the catalyst surface. The Na + gated, water-transport nanochannel membrane showed H 2 O/CO 2 selectivity of 560 at 250 °C and 300 psig for H 2 O/CO 2 /CO/H 2 /MeOH gas mixtures. The selectivities of H 2 O/H 2 , H 2 O/CO, and H 2 O/MeOH were 190, 170, and 80, respectively. In a laboratory-scale membrane reactor, DME synthesis testing using this membrane, a DME production rate of 440 g DME /kg cat /h was achieved at 260 °C and 550 psig. Compared to the packed bed reactor, the CO 2 conversion and DME production rate in the membrane reactor were 80% and three times higher, respectively. A prototype test system (1 kg/day) was designed, constructed, and tested. A DME production rate of 1.31 kg/day and a DME productivity of 360 g/h/kg were achieved in the prototype membrane reactor. Good stability was demonstrated during 150-h continuous operation and multiple startups/shutdowns tests.
Supply Chain Sustainability Analysis of Renewable Hydrocarbon Fuels via Indirect Liquefaction, Ex Situ Catalytic Fast Pyrolysis, Hydrothermal Liquefaction, Combined Algal Processing, and Biochemical Conversion: Update of the 2020 State-of-Technology Cases
The Department of Energy’s (DOE) Bioenergy Technologies Office (BETO) aims to develop and deploy technologies to transform renewable biomass resources into commercially viable, high-performance biofuels, bioproducts, and biopower through public and private partnerships (U.S. Department of Energy, 2016). BETO and its national laboratory teams conduct in-depth techno-economic assessments (TEA) of biomass feedstock supply and logistics and conversion technologies to produce biofuels. There are two general types of TEAs: A design case outlines a target case (future projection) for a particular biofuel pathway. It enables identification of data gaps and research and development needs and provides goals and benchmarks against which technology progress is assessed. A state of technology (SOT) analysis assesses progress within and across relevant technology areas based on actual results at current experimental scales relative to technical targets and cost goals from design cases, and includes technical, economic, and environmental criteria as available. In addition to developing a TEA for a pathway of interest, BETO also performs a supply chain sustainability analysis (SCSA). The SCSA takes the life-cycle analysis approach that BETO has been supporting for about 20 years. It enables BETO to identify energy consumption, environmental, and sustainability issues that may be associated with biofuel production. Approaches to mitigate these issues can then be developed. Additionally, the SCSA allows for comparison of energy and environmental impacts across biofuel pathways in BETO’s research and development portfolio. This technical report describes the SCSAs for the production of renewable hydrocarbon transportation fuels via a range of conversion technologies in the 2020 SOTs: (1) renewable high octane gasoline (HOG) via indirect liquefaction (IDL) of woody lignocellulosic biomass (note that the IDL pathway in this SCSA represents the syngas conversion design [Harris et al. 2021]); (2) renewable gasoline (RG) and diesel (RD) blendstocks via ex situ catalytic fast pyrolysis of woody lignocellulosic biomass [Abhijit et al. 2021]; (3) RD via hydrothermal liquefaction (HTL) of wet sludge from a wastewater treatment plant; (4) renewable hydrocarbon fuels via biochemical conversion of herbaceous lignocellulosic biomass (Davis et al. 2021; Lin et al. 2021); (5) renewable diesel via HTL of a blend of algae (Davis and Klein, 2021) and woody biomass (Hartley et al. 2020); and (6) renewable diesel via combined algae processing (CAP) (Wiatrowski and Davis, 2021). This technical report focuses on the environmental performance of these six biofuel production pathways in their 2020 SOT cases. The results of these renewable hydrocarbon fuel pathways in these SCSA analyses update those for the respective 2019 SOT cases (Cai et al. 2020). They also provide an opportunity to examine the impact of technology improvements in both biomass feedstock production and biofuel production that have been achieved in 2020 SOTs on the sustainability performance of these renewable transportation fuels. The SCSA results also reflect updates to Argonne National Laboratory’s Greenhouse gases, Regulated Emissions, and Energy use in Technologies (GREET®) model, which was released in October 2020 (Wang et al. 2020). These GREET updates include the production of natural gas, electricity, and petroleum-based fuels that can influence biofuels’ supply chain greenhouse gas (GHG) (CO 2 , CH 4 , and N 2 O) emissions, water consumption, and air pollutant emissions. GHG emissions, water consumption, and nitrogen oxides (NO x ) emissions are the main sustainability metrics assessed in this analysis. In this analysis, we define water consumption as the amount of water withdrawn from a freshwater source that is not returned (or returnable) to a freshwater source at the same level of quality. Life-cycle fossil energy consumption and net energy balance, which is the life-cycle fossil energy consumption deducted from the renewable biofuel energy produced, are also assessed.
Techno-economic performances and life cycle greenhouse gas emissions of various ammonia production pathways including conventional, carbon-capturing, nuclear-powered, and renewable production
Ammonia (NH 3 ) is conventionally produced using fossil natural gas (NG) for hydrogen production through steam reformation and synthesis in the Haber–Bosch (HB) process. The global conventional ammonia production contributes more than 420 million tons of CO 2 emissions annually. Here, in this work, we investigated the techno-economics and well-to-plant-gate (WTG) greenhouse gas (GHG) emissions of conventional NG-based, carbon-capturing, nuclear-powered, and renewable ammonia production by developing an engineering process model for each. Carbon-capturing ammonia production refers to the NG-based ammonia production while capturing CO 2 and transporting it via pipelines for storage or utilization. Nuclear-powered and renewable ammonia production represents an alternative ammonia production through water electrolysis, air separation, and the HB process using carbon-free energy sources. Nuclear and renewable energy sources are assumed to be used for nuclear-powered and renewable ammonia production, respectively. Sensitivity analyses are performed for CO 2 pipeline transport distances, potential carbon capture tax credits, and clean H 2 production cost. Carbon-capturing ammonia production reduces WTG GHG emissions by 55–70% compared to conventional NG-based ammonia production methods. Nuclear-powered and renewable ammonia production almost eliminate GHG emissions since energy supply is either zero carbon or near-zero carbon. However, when $4.16–4.83 per kg is the cost assumed for clean H 2 production using state-of-the-art electrolysis technologies, the levelized costs of nuclear-powered and renewable ammonia are calculated to be $0.92–1.06 per kg NH 3 , which are approximately four times higher than the conventional NG-based ammonia production cost. The cost of CO 2 emission avoidance is estimated in the range of $266–318 per metric ton of CO 2 for nuclear-powered and renewable ammonia production. The clean H 2 production cost is the major contributor to the levelized costs of nuclear-powered and renewable ammonia production. A lower production cost, near $1 per kg H 2 , for clean H 2 is required for nuclear-powered and renewable ammonia production to be cost-competitive with conventional NG-based ammonia production.
Renewable hydrogen and ammonia for combined heat and power systems in remote locations: Optimal design and scheduling
Abstract Using hydrogen (H ) and ammonia (NH ) for renewable energy storage has the potential to enable economical power and heat supply with high renewable penetrations, especially in remote locations which are characterized by high energy costs. In this work we assess the economic competitiveness of renewable combined heat and power (CHP) systems in Mahaka HI, Nantucket MA, and Northwest Arctic Borough (NWAB) AK by optimally designing these systems for scenarios in which power and heat can be purchased over a range of historical energy prices as well as when 100% renewable supply is required. We use a combined optimal design and scheduling model which minimizes annualized net present cost by determining optimal technology selection and size simultaneously with optimal schedules for each period of a system operating horizon aggregated from full year hourly resolution data via a consecutive temporal clustering algorithm. We find that renewable generation meets at least 85% of power demands and 75% of heat demands under the lowest energy prices investigated. Higher conventional energy prices lead to increased renewable penetration which is facilitated by renewable NH as a seasonal energy storage medium, as are 100% renewable CHP systems. NH is used for power generation with heat cogeneration in all three locations, as well as directly for heating in NWAB. On an annual cost basis, NH ‐enabled 100% renewable CHP is only 3% more expensive in Mahaka and NWAB than systems which can purchase energy at the lowest prices, while it is 15% more expensive in Nantucket.
Supply Chain Sustainability Analysis of Renewable Hydrocarbon Fuels via Indirect Liquefaction, Ex Situ Catalytic Fast Pyrolysis, Hydrothermal Liquefaction, Combined Algal Processing, and Biochemical Conversion: Update of the 2020 State-of-Technology Cases
This technical report describes the SCSAs for the production of renewable hydrocarbon transportation fuels via a range of conversion technologies in the 2020 SOTs: (1) renewable high octane gasoline (HOG) via indirect liquefaction (IDL) of woody lignocellulosic biomass (note that the IDL pathway in this SCSA represents the syngas conversion design); (2) renewable gasoline (RG) and diesel (RD) blendstocks via ex situ catalytic fast pyrolysis of woody lignocellulosic biomass; (3) RD via hydrothermal liquefaction (HTL) of wet sludge from a wastewater treatment plant; (4) renewable hydrocarbon fuels via biochemical conversion of herbaceous lignocellulosic biomass; (5) renewable diesel via HTL of a blend of algae and woody biomass; and (6) renewable diesel via combined algae processing (CAP). This technical report focuses on the environmental performance of these six biofuel production pathways in their 2020 SOT cases. The results of these renewable hydrocarbon fuel pathways in these SCSA analyses update those for the respective 2019 SOT cases. They also provide an opportunity to examine the impact of technology improvements in both biomass feedstock production and biofuel production that have been achieved in 2020 SOTs on the sustainability performance of these renewable transportation fuels. The SCSA results also reflect updates to Argonne National Laboratory’s Greenhouse gases, Regulated Emissions, and Energy use in Technologies (GREET ® ) model, which was released in October 2020. These GREET updates include the production of natural gas, electricity, and petroleum-based fuels that can influence biofuels’ supply chain greenhouse gas (GHG) (CO 2 , CH 4 , and N 2 O) emissions, water consumption, and air pollutant emissions. GHG emissions, water consumption, and nitrogen oxides (NO x ) emissions are the main sustainability metrics assessed in this analysis. In this analysis, we define water consumption as the amount of water withdrawn from a freshwater source that is not returned (or returnable) to a freshwater source at the same level of quality. Life-cycle fossil energy consumption and net energy balance, which is the life-cycle fossil energy consumption deducted from the renewable biofuel energy produced, are also assessed.
Innovation in complementary energy technologies from renewable energy policies
Complementary renewable technologies support renewable energy use as they can help balance the intermittency of solar and wind generation. Previous research has shown that environmental policies directly targeting renewable energy can drive innovation in solar PV and wind technology. This study explores the impact of renewable policies on innovation in complementary renewable technology that assists with integration, including combustion with mitigation potential, efficient power transmission or distribution, and enabling technologies. We use negative binomial models and a panel of 25 OECD countries from 1997 to 2015 to evaluate these relationships. We are not able to find evidence that renewable policies incentivize innovation in complementary combustion or transmission and distribution technologies, and only limited evidence that demand-pull instruments are associated with increased innovation in smart grid technology. Technology-push policies, such as public research and development funds for renewable energy, have had limited impact on grid-supporting energy storage innovation. Our findings suggest that policymakers wishing to accelerate these complementary technologies need to go beyond policies targeting renewable energy in order to drive innovation in complementary fields.
Renewable Energy at NASA's Johnson Space Center
NASA's Johnson Space Center has implemented a great number of renewable energy systems. Renewable energy systems are necessary to research and implement if we humans are expected to continue to grow and thrive on this planet. These systems generate energy using renewable sources - water, wind, sun - things that we will not run out of. Johnson Space Center is helping to pave the way by installing and studying various renewable energy systems. The objective of this report will be to examine the completed renewable energy projects at NASA's Johnson Space Center for a time span of ten years, beginning in 2003 and ending in early 2014. This report will analyze the success of each project based on actual vs. projected savings and actual vs. projected efficiency. Additionally, both positive and negative experiences are documented so that lessons may be learned from past experiences. NASA is incorporating renewable energy wherever it can, including into buildings. According to the 2012 JSC Annual Sustainability Report, there are 321,660 square feet of green building space on JSC's campus. The two projects discussed here are major contributors to that statistic. These buildings were designed to meet various Leadership in Energy and Environmental Design (LEED) Certification criteria. LEED Certified buildings use 30 to 50 percent less energy and water compared to non-LEED buildings. The objectives of this project were to examine data from the renewable energy systems in two of the green buildings onsite - Building 12 and Building 20. In Building 12, data was examined from the solar photovoltaic arrays. In Building 20, data was examined from the solar water heater system. By examining the data from the two buildings, it could be determined if the renewable energy systems are operating efficiently. Objectives In Building 12, the data from the solar photovoltaic arrays shows that the system is continuously collecting energy from the sun, as shown by the graph below. Building 12 has two solar inverters, located on the second floor, that collected the data from the solar photovoltaic arrays. The data displayed here is the total energy produced by the system. These are cumulative amounts, so the last point on the graph shows all of the energy collected from the system since the start of its operation. The data shown here was manually collected from the solar inverters. However, the data is also automatically recorded through EBI. Through analysis of both sets of data it was determined that the EBI data was faulty. For example, from the manually collected data it can be determined that a total of 73 kWh of energy was collected between the dates of 1/16/2014 – 1/22/2014. The EBI data reports that approximately 17800 kWh of energy was collected during the same time frame. Not only does this exceed the time frame examined, but it also exceeds the total energy collected from the start of collection as recorded from the inverters. This leads to the belief that there is a malfunction with the automatic recording of the energy. In Building 20, data was examined from the solar water heater dating back many months and found that the pump for the solar water heater system was not operating properly, as exhibited in the graph shown below. The pump operates on a solar energy system, meaning that it collects energy throughout the day from the sun. Because of this, the system would stop operating shortly after the sun set because of a lack of sunlight. At that point, the graph should show a zero flow rate, but as exhibited in the graph below, that is not the case. It is clearly shown that the pump is continuously operating, even during the night. It was also observed that the majority of the time the pump would not turn on at all, despite good weather conditions. This led to the conclusion that the pump is malfunctioning, and needs to be examined and fixed.
Renewable energy and biological conservation in a changing world
Without a shift to renewable energy sources, climate change will have adverse effects on many terrestrial and aquatic species. On the other hand, replacing fossil fuels with renewable energy will have different effects on wildlife, some negative. To protect biota, while navigating the complexities surrounding the transition to renewable energy, will require sharing knowledge between energy experts and wildlife experts, as well as policy makers and resource managers. This special issue is intended to advance the conversation. Interactions between renewable energy facilities and fauna are complex. Each source of renewable energy has its own conservation concerns, and each presents its own set of opportunities for mitigation; Other concerns and mitigations are shared. In this overview, we review climate risks to biota, clarify the complementarities among renewables for the conservation community, and summarize research on energy effects on biota for the energy community. The papers invited for this special issue address fossil (coal, oil, natural gas) and renewable energy (terrestrial biomass energy, hydropower, marine-hydrokinetic energy, wind energy, solar energy) and affected fauna. Finally, we hope that the results of these studies, and others like them, set us on a path toward low-carbon energy systems that provide society with energy while protecting future biodiversity.
Integration of renewable energy generation and storage systems for emissions reduction in an islanded campus microgrid
Microgrid connected building communities are projected to play an integral part in the clean energy transition. These types of systems, when integrated with distributed energy resources (DERs) such as combined heat and power (CHP), district heating and cooling, renewable generation, and energy storage, can provide clean, reliable power to critical facilities and vulnerable communities. The intermittent nature of renewable generation is a challenge when integrating renewables into any grid system, but particularly in islanded microgrids. The University of Texas at Austin (UT) operates an islanded microgrid powered by a CHP plant, while also utilizing district heating and cooling systems and thermal energy storage (TES). High fidelity operating data was used to develop a validated reduced order model of UT’s integrated campus energy systems to serve as a testbed for use in a case study. Hypothetical renewable energy installations on land owned by UT in west Texas were modeled and integrated into the validated campus models along with battery energy storage (BES). Simulations showed that a combination of renewable energy from wind, and optimally controlled 24-hour thermal and battery storage systems could reduce carbon dioxide emissions on campus by 45.4%. The additional retrofit of burner systems to utilize hydrogen natural gas blends resulted in an overall annual emissions reduction of 54.7%. Carbon capture and storage eliminated the majority of the remaining emissions with increased plant energy expenditure. The presented simulations display the practical limitations of a CHP system complemented by renewable generation and short-term storage in eliminating emissions. Furthermore, results highlight the need for further research and development in long duration storage technologies and hydrogen fueled turbines to increase penetration of renewable energy and reduce emissions.
Electrification of residential and commercial buildings integrated with hybrid renewable energy systems: A techno-economic analysis
Here, this study assesses the techno-economic viability of city-scale building electrification, comparing a base case scenario with conventional HVAC systems to an electrified scenario with heat pump systems. EnergyPlus simulations reveal a 28% increase in annual electricity consumption in the electrified scenario, shifting the peak consumption from summer to winter with a 49% surge. Hybrid renewable energy systems (HRESs) are then evaluated using HOMER Pro, considering renewable penetration from 0% to 100%. The net present cost (NPC) of the base case and electrified scenarios range from $\$10.34$ to $\$24.38$ billion and $\$8.79$ to $\$50.31$ billion, respectively. Sensitivity analysis explores the impact of carbon tax, fuel price, and renewable subsidies on HRESs in the electrified scenario. Results indicate that applying a carbon tax up to $\$120$/tonne of CO 2 increases the optimum renewable fraction from 5% to 26%, while higher fuel prices and renewable subsidies further enhance the feasibility by shifting the optimum renewable fraction to 60% and 54%, respectively, demonstrating the interplay between economic factors and renewable integration in electrified urban contexts.
When energy doesn’t add up: use of an energyshed framework in assessing progress towards renewable energy transitions
Global progress in energy transitions to support climate mitigation goals has been slower than anticipated; this has prompted shifts away from traditional paradigms of regulated energy ownership towards a model of energy democratization by local communities and individuals. For example, in the United States, local communities in over 250 cities, counties, and states have made pledges to reach 100% renewable electrification by target dates ranging from 2020 to 2050. However, the availability of infrastructure and the competition for renewable energy resources, as well as lack of awareness of these limitations, present significant barriers to overcome. In this study, we explored a subset of 31 of these cities to assess their current electricity generation and how much further they have to go to meet their goals. Through an energyshed framework, we estimated powerplant electricity allocation to each city assuming competition for power from various renewable and non-renewable resource types, as well as look at the ‘best case scenario’ assuming 100% allocation of renewable-sourced electricity for a handful of cities in order to understand the existing and planned energy mixes for 2021 and the following 20 years. It is likely most cities will meet 10% of their energy demand with renewable energy, with best cases scenarios reaching between 35% and 65% renewable penetration, within the next 20–30 years. This highlights the need for infrastructural development in the energy sector, as well as intentional planning efforts in order to make these energy goals a reality.
Renewable Thermal Energy Systems: Characterization of the Most Important Thermal Energy Applications in Buildings and Industry (Report 1)
This report is the first in a three-report series that evaluates the provision of renewable heat for industry and buildings via current and prospective renewable thermal energy system (RTES) technologies. The RTES project has undertaken initial research focused on technologies that could be suited for industrial process heat applications at different temperature levels, and, where possible, gathered performance and cost data for these technologies. This project does not directly evaluate RTES for distributed residential or commercial applications, nor does it yet include documented cases or modeling of RTES using geothermal, biomass, waste heat, renewable fuels like renewable natural gas, or hydrogen production. The three technical reports are summarized as follows: Renewable Thermal Energy Systems: Characterization of the Most Important Thermal Energy Applications in Buildings and Industry (Report 1), this report: summary of thermal demands of U.S. industry and buildings, and relevant hybrid RTES configurations; Renewable Thermal Energy Systems: Systemic Challenges and Transformational Policies (Report 2): discussion of socio-technical characteristics of RTES, innovation challenges, and supporting policies. Available at: https://www.nrel.gov/docs/fy23osti/83020.pdf; Renewable Thermal Energy Systems: Modeling Developments and Future Directions (Report 3): Energy yield and performance modeling of RTES, techno-economic analysis via case studies, and proposed development of a user decision support tool. Available at: https://www.nrel.gov/docs/fy23osti/83021.pdf.
The Lithuania 100% Renewable Energy Study - Interim Results: Electricity System Scenarios for 2030 [Slides]
Lithuania's Energy Vision aims to achieve self-sufficiency in electricity generation by 2035 and transition to 100% renewable energy as soon as possible while maintaining affordability, reliability, and energy security. The Lithuania Energy Agency (LEA) is partnering with the National Renewable Energy Laboratory (NREL) to conduct the Lithuania 100% Renewable Energy Study (Lithuania 100) to provide evidence-based analysis for development of Lithuania's National Energy Independence Strategy. The Lithuania 100 Study leverages unique tools and capabilities of NREL to provide rigorous technical analysis of clean energy policies to achieve 100% renewable energy, and assess impacts on electricity grid operations, hydrogen system development, electricity distribution networks, air quality, and human health outcomes. The study is supported by a stakeholder committee chaired by the Ministry of Energy of Lithuania and implemented by four technical working groups. This report provides highlights of key interim results from modeling of Lithuania's near-term electricity grid through the year 2030. Results show that Lithuania has sufficient renewable energy potential, flexible generation capacity, and interconnection with neighboring European Union countries to reliably meet projected 2030 electricity demand with 100% renewable energy. A range of scenarios were modeled, each of which achieves at least 100% renewable energy in electricity, on average over the year, by 2030. Potential demands for hydrogen across industrial and transportation sectors were also evaluated, as well as the cost of hydrogen produced in Lithuania by 2030.
Renewable Energy Systems in the Transition of North America to Net Zero Emissions
The North American transition to low-carbon energy sources depends on the technology decisions of its diverse communities and stakeholders. Each region and industry will have its own portfolio of renewable energy technologies to meet the common goal of net zero emissions. Our presentation will share integrated renewable energy solutions being explored at scale by major U.S cities, rural regions dependent on oil and gas, and industries redefining their infrastructure and their missions. Case examples will be presented on: the Los Angeles 100% renewable energy goals; challenges and opportunities of decarbonizing and reducing emissions from the oil and gas industry; repurposing oil and gas infrastructure such as using pipelines for hydrogen blends and renewable natural gas and idle wells for geothermal energy and energy storage; treatment of produced water using renewable energy for agriculture applications; and the preserving water and agricultural resources in the transition to renewable energy. Key challenges will also be discussed, including resilience to increasing disasters, stranded assets, unequal community impact, and meeting the last 5-20% of energy with renewable energy.
Powering Data Centers with Clean Energy: A Techno-Economic Case Study of Nuclear and Renewable Energy Dependability
Rising data demands from artificial intelligence (AI) and large language models (LLMs) generating images, videos, and text have prompted increased need for larger and more robust data centers in the United States. Major companies interested in these larger data centers face the choice of linking them to existing regional grids, building stand-alone power supplies onsite, or a combination of both. The request, review, and approval process for new transmission lines to grids in the United States, however, has grown in recent years to times spans rivaling those of new construction for nuclear power plants. Building an islanded power supply for each data center is therefore becoming a prominent option. In this case study, several technologies are modeled in techno-economic simulations for long-term system costs subject to fixed electricity demand from a singular data center. A 250 MWe data center is assumed with additional 50 MWe for resiliency. Techno-economic simulations are conducted using the Holistic Energy Resource Optimization Network (HERON) software, which is a part of the Framework for Optimization of Resources and Economics (FORCE) tool suite. Technologies considered include solar, wind, lithium-ion batteries, and several types of nuclear reactors: large-scale reactors, small modular reactors, and microreactors. A low- and high-cost estimate for each technology is assumed to develop a range of expected economic performance. Low-cost estimates included several clean energy production tax credits. Different combinations of renewable energy generators with nuclear reactors are considered, ranging from a fully renewable-powered data center to a fully nuclear-powered data center. Historic time series of wind and solar availability from the Texas grid are used to train a reduced order model; this model then generates unique time series with similar characteristics of the training dataset. Multiple scenarios of weather and subsequent operations are simulated for each renewable-nuclear combination to determine total costs throughout the project lifetime. Fully renewable-powered configurations required large amounts of installed capacity (GW scale) in the simulations to meet the fixed demand of the data center. This is due to some scenarios in the historical dataset which captured low-wind and low-solar days, requiring over-building of these technologies as well as batteries to compensate for the low amounts of electricity generation. Fully nuclear-powered configurations outperformed the fully renewable and mixed renewable-nuclear configurations in terms of cost, with ranges between $1B and $10B in 2023 USDs compared to $40B+ for fully renewable configurations. Of the nuclear technologies, small modular reactors performed better economically than large-scale nuclear models due to lower projected capital costs, and both performed better than the microreactor models. These results demonstrate the applicability of firm, dispatchable electricity resources from baseload generators like nuclear power plants for operating facilities that run at constant power without daily variability.
Applications of explainable artificial intelligence in renewable energy research
Researchers in renewable energy are applying deep learning (DL) to a variety of problems from diverse renewable energy domains, such as biofuels, wind, solar, power systems, buildings, vehicles, and transportation systems. Improvements in accuracy may be demonstrated using DL in laboratory settings. However, the lack of interpretability of DL models poses a practical limitation to their utility in advancing scientific knowledge and in the deployment of DL models in safety-critical energy systems. In this article, we discuss explainable artificial intelligence (XAI) as one pathway toward more interpretable DL models. We explore a brief timeline of U.S. national laboratory interest in XAI, an overview and taxonomy of methods in the field of XAI, and a selection of applications across renewable energy research domains. We conclude by highlighting pivotal areas where XAI can accelerate innovation in artificial intelligence for renewable energy research and other essential future directions.