Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Regeneration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Regenerable Iodine Water-Disinfection System

Iodinated resin bed for disinfecting water regenerated to extend its useful life. Water flows through regeneration bed of crystalline iodine during regeneration. At other times, flow diverted around regeneration bed. Although regeneration cycle was manually controlled in demonstration, readily automated to start and stop according to signals and stop according to signals from concentration sensors. Further benefit of regeneration is that regeneration bed provides highly concentrated biocide source (200 mg/L) when needed. Concentrated biocide used to superiodinate system after contamination from routine maintenance or unexpected introduction of large concentration of microbes.

Sauer, Richard L.↗
NASA NTRS2006

An Initial Non-Equilibrium Porous-Media Model for CFD Simulation of Stirling Regenerators

The objective of this paper is to define empirical parameters for an initial thermal non-equilibrium porous-media model for use in Computational Fluid Dynamics (CFD) codes for simulation of Stirling regenerators. The two codes currently used at Glenn Research Center for Stirling modeling are Fluent and CFD-ACE. The codes porous-media models are equilibrium models, which assume solid matrix and fluid are in thermal equilibrium. This is believed to be a poor assumption for Stirling regenerators; Stirling 1-D regenerator models, used in Stirling design, use non-equilibrium regenerator models and suggest regenerator matrix and gas average temperatures can differ by several degrees at a given axial location and time during the cycle. Experimentally based information was used to define: hydrodynamic dispersion, permeability, inertial coefficient, fluid effective thermal conductivity, and fluid-solid heat transfer coefficient. Solid effective thermal conductivity was also estimated. Determination of model parameters was based on planned use in a CFD model of Infinia's Stirling Technology Demonstration Converter (TDC), which uses a random-fiber regenerator matrix. Emphasis is on use of available data to define empirical parameters needed in a thermal non-equilibrium porous media model for Stirling regenerator simulation. Such a model has not yet been implemented by the authors or their associates.

Tew, Roy C.↗
DOE OSTI2026

Untapped Benefits of Porous Liquids for Gas Capture: Low-Energy Regeneration

Current liquid-phase gas capture materials incur high operational costs due to energy-intensive regeneration processes, creating an industrial need for alternative materials that retain engineering benefits while reducing energy requirements. Porous liquids (PLs), liquid-phase materials with permanent internal porosity, have emerged as promising replacements with excellent gas absorption capacity and selectivity. Despite these benefits, evaluation of regeneration in PLs remains rare. In this Perspective, we evaluate the effects of solvent interactions, mass transport, and binding site formation that control PL regeneration. While conventional regeneration methods exist in PLs, the diversity of PL compositions allows for novel regeneration processes including light irradiation via use of photosensitive azobenzene-based cages, isostatic compression to collapse internal pore structures, and localized heating via sonication for gas desorption. In conclusion, the wide variability in porous host materials that generate the internal porosity in PLs facilitates innovative low-energy regeneration pathways, positioning them as a transformative solution in separation technologies.

gas capture↗
NASA NTRS1994

Regenerable Iodine Water-Disinfection System

Iodinated resin bed for disinfecting water regenerated to extend useful life. Water flows through regeneration bed of crystalline iodine during regeneration. At other times, flow diverted around regeneration bed. Although regeneration cycle manually controlled readily automated to start and stop according to signals from concentration sensors. Further benefit of regeneration is bed provides highly concentrated biocide source when needed. Concentrated biocide used to superiodinate system after contamination from routine maintenance or unexpected introduction of large concentration of microbes.

Sauer, Richard L.↗
NASA NTRS2007

A Microfabricated Segmented-Involute-Foil Regenerator for Enhancing Reliability and Performance of Stirling Engines

An actual-size microfabricated regenerator comprised of a stack of 42 disks, 19 mm diameter and 0.25 mm thick, with layers of microscopic, segmented, involute-shaped flow channels was fabricated and tested. The geometry resembles layers of uniformly-spaced segmented-parallel-plates, except the plates are curved. Each disk was made from electro-plated nickel using the LiGA process. This regenerator had feature sizes close to those required for an actual Stirling engine but the overall regenerator dimensions were sized for the NASA/Sunpower oscillating-flow regenerator test rig. Testing in the oscillating-flow test rig showed the regenerator performed extremely well, significantly better than currently used random-fiber material, producing the highest figures of merit ever recorded for any regenerator tested in that rig over its approximately 20 years of use.

Ibrahim, Mounir↗
NASA NTRSDate not supplied

Black Hills Wildfires: Mapping Post-fire Conifer Regeneration using Snow-on Imagery

The 2000 Jasper Fire in the Black Hills of South Dakota was the largest wildfire to date in the region, burning over 83,000 acres of ponderosa pine forest. In collaboration with partners from the United States Forest Service (USFS) Black Hills Experimental Forest, USFS Rocky Mountain Research Station, and United States Geological Survey Geosciences and Environmental Change Science Center, we characterized post-fire forest regeneration within high-severity burn patches. We accomplished this by implementing novel conifer detection techniques using a snow index mask to create a winter, snow-on image composite from Landsat 8 Operational Land Imager (OLI) and Sentinel-2 Multispectral Instrument (MSI) data. We utilized 2015 USFS stem maps of field-observed regeneration plots and ocularly sampled additional reforestation sites planted in 2001–2013. In Google Earth Engine (GEE), the field data and imagery were used to train a Random Forest (RF) model. The RF model classified 2021 conifer regeneration density as low, medium, or high across the high-severity burn area with an overall accuracy of 81.3%. Approximately 45.9% of the high-severity burn had low or no regeneration (0-40 trees per acre) 20 years post-fire. Given our partners' desire to find easily accessible low conifer regeneration zones, we identified 4,079 acres of priority planting sites that were within 1,500 feet of roads, had not been planted previously, and were larger than 50 acres. This method supports the use of snow-on imagery as a successful technique to identify conifer regeneration.

Casey Menick​↗
NASA NTRS2022

Black Hills Wildfires: Mapping Post-Fire Conifer Regeneration using Snow-On Imagery

The 2000 Jasper Fire in the Black Hills of South Dakota was the largest wildfire to date in the region, burning over 83,000 acres of ponderosa pine forest. In collaboration with partners from the United States Forest Service (USFS) Black Hills Experimental Forest, USFS Rocky Mountain Research Station, and United States Geological Survey Geosciences and Environmental Change Science Center, we characterized post-fire forest regeneration within high-severity burn patches. We accomplished this by implementing novel conifer detection techniques using a snow index mask to create a winter, snow-on image composite from Landsat 8 Operational Land Imager (OLI) and Sentinel-2 Multispectral Instrument (MSI) data. We utilized 2015 USFS stem maps of field-observed regeneration plots and ocularly sampled additional reforestation sites planted in 2001–2013. In Google Earth Engine (GEE), the field data and imagery were used to train a Random Forest (RF) model. The RF model classified 2021 conifer regeneration density as low, medium, or high across the high-severity burn area with an overall accuracy of 81.3%. Approximately 45.9% of the high-severity burn had low or no regeneration (0-40 trees per acre) 20 years post-fire. Given our partners' desire to find easily accessible low conifer regeneration zones, we identified 4,079 acres of priority planting sites that were within 1,500 feet of roads, had not been planted previously, and were larger than 50 acres. This method supports the use of snow-on imagery as a successful technique to identify conifer regeneration.

Casey Menick↗
NASA NTRSDate not supplied

Mapping Post-fire Conifer Regeneration using Snow-on Imagery

The 2000 Jasper Fire in the Black Hills of South Dakota was the largest wildfire to date in the region, burning over 83,000 acres of ponderosa pine forest. In collaboration with partners from the United States Forest Service (USFS) Black Hills Experimental Forest, USFS Rocky Mountain Research Station, and United States Geological Survey Geosciences and Environmental Change Science Center, we characterized post-fire forest regeneration within high severity burn patches. We accomplished this by implementing novel conifer detection techniques using a snow index mask to create a winter, snow-on image composite from Landsat 8 Operational Land Imager (OLI) and Sentinel-2 Multispectral Instrument (MSI) data. We utilized 2015 USFS stem maps of field-observed regeneration plots and ocularly sampled reforestation sites planted from 2001–2013. The field data and imagery were used to train a Random Forest (RF) model in Google Earth Engine. The RF model classified conifer regeneration density as low, medium, or high across the high-severity burn area with an overall accuracy of 81.3% for 2021. Approximately 45.9% of the high-severity burn area had low or no regeneration (0-40 trees per acre) 20 years post-fire. Given our partners' desire to find easily accessible low conifer regeneration zones, we identified 4,079 acres of priority planting sites that were within 1,500 feet of roads, had not been planted previously, and were larger than 50 acres. This method supports the use of snow-on imagery as a successful technique to identify conifer regeneration in a post-wildfire landscape.

Yeshey Seldon↗
DOE OSTI2025

Motion of Molecules in Supramolecular Scaffolds Enhances Bone Regeneration

The regeneration of human tissues is a great scientific challenge and a critical factor to achieve a long healthspan and prevent disabilities due to injury or disease. Materials chemistry can contribute to this goal with the development of bioactive supramolecular systems that can signal cells for regeneration. Recent work in our laboratory using in vivo models of spinal cord injury and cartilage regeneration has demonstrated that the motion of bioactive molecules in supramolecular scaffolds enhances receptor signaling. We report here on a novel molecular strategy to control supramolecular motion in filamentous assemblies using bone regeneration as a functional target. The supramolecular assemblies are composed of monomers that arrange, by design, with either parallel or antiparallel β-sheets, and some of them contain a terminal peptide sequence that binds BMP-2. We found that parallel β-sheet supramolecular assemblies promote greater osteogenic differentiation of progenitor cells in vitro relative to antiparallel assemblies, as well as superior quality of newly regenerated bone in a rat model of spinal fusion. Furthermore, these assemblies drastically reduce the dangerous supraphysiological dose of BMP-2 used clinically for spinal fusion. Here, we attribute the enhanced bioactivity to the weaker nature of hydrogen bonds in parallel relative to antiparallel β-sheet assemblies, which in turn allows greater supramolecular motion and cell signaling of the growth factor-binding molecules.

Anatomy↗
DOE OSTI2026

Toluene adsorption and capacity regeneration using zeolite-based monolith and activated carbon fiber felt

Common adsorbents studied to remove volatile organic compounds (VOCs) from indoor air can release previously adsorbed VOCs back into the indoor space when the adsorbent is saturated or if the VOC concentration fluctuates. A durable adsorbent with a continuous regeneration strategy could prevent this recontamination of the indoor air and reduce adsorbent disposal waste. A deeper understanding of the adsorption and desorption behavior of VOC adsorbents is needed to create an efficient regeneration strategy. This study investigated the adsorption and thermal desorption behavior of toluene on two different adsorbents, (1) a zeolite-based adsorbent and (2) an activated carbon fiber (ACF) felt. Consistent adsorption behavior across a series of toluene concentrations was used to experimentally determine effective adsorption capacity. When the cumulative adsorption between thermal regeneration steps was maintained below the maximum effective capacity with 0% breakthrough, the zeolite-based adsorbent was found to effectively minimize passive desorption. The impact of regeneration feed conditions, such as inert, oxidizing, humidified air, on thermal desorption was examined. These conditions influenced desorption of the zeolite-based adsorbent but had minimal impact on the ACF felt adsorbent, which would lead to different regeneration schedules and methods for applications in buildings' heating, ventilation, and air conditioning (HVAC) systems.

Moses-DeBusk, Melanie [Oak Ridge National Laborato↗
NASA NTRS1979

Development of the electrochemically regenerable carbon dioxide absorber for portable life support system application

As the length of manned space missions increase, more ambitious extravehicular activities (EVAs) are required. For the projected longer mission the use of expendables in the portable life support system (PLSS) will become prohibited due to high launch weight and volume requirements. Therefore, the development of a regenerable CO2 absorber for the PLSS application is highly desirable. The paper discusses the concept, regeneration mechanism, performance, system design, and absorption/regeneration cycle testing of a most promising concept known as ERCA (Electrochemically Regenerable CO2 Absorber). This concept is based on absorbing CO2 into an alkaline absorbent similar to LiOH. The absorbent is an aqueous solution supported in a porous matrix which can be electrochemically regenerated on board the primary space vehicle. With the metabolic CO2 recovery the ERCA concept results in a totally regenerable CO2 scrubber. The ERCA test hardware has passed 200 absorption/regeneration cycles without performance degradation.

Woods, R. R.↗
NASA NTRS1982

Experimental performance of the regenerator for the Chrysler upgraded automotive gas turbine engine

Automobile gas turbine engine regenerator performance was studied in a regenerator test facility that provided a satisfactory simulation of the actual engine operating environment but with independent control of airflow and gas flow. Velocity and temperature distributions were measured immediately downstream of both the core high-pressure-side outlet and the core low-pressure-side outlet. For the original engine housing, the regenerator temperature effectiveness was 1 to 2 percent higher than the design value, and the heat transfer effectiveness was 2 to 4 percent lower than the design value over the range of test conditions simulating 50 to 100 percent of gas generator speed. Recalculating the design values to account for seal leakage decreased the design heat transfer effectiveness to values consistent with those measured herein. A baffle installed in the engine housing high-pressure-side inlet provided more uniform velocities out of the regenerator but did not improve the effectiveness. A housing designed to provide more uniform axial flow to the regenerator was also tested. Although temperature uniformity was improved, the effectiveness values were not improved. Neither did 50-percent flow blockage (90 degree segment) applied to the high-pressure-side inlet change the effectiveness significantly.

Winter, J. M.↗
NASA NTRS1991

Ceramic regenerator program

The feasibility of fabricating an Air Turbo Ramjet (ATR) regenerator containing intricate hydraulic passages from a ceramic material in order to allow operation with high temperature combustion gas and to reduce weight as compared with metallic materials was demonstrated. Platelet technology, ceramic tape casting, and multilayer ceramic packaging techniques were used in this fabrication of subscale silicon nitride components. Proof-of-concept demonstrations were performed to simulate a methane cooled regenerator for an ATR engine. The regenerator vane was designed to operate at realistic service conditions, i.e., 600 psi in a 3500 R (3040 F), 500 fps combustion gas environment. A total of six regenerators were fabricated and tested. The regenerators were shown to be able to withstand internal pressurization to 1575 psi. They were subjected to testing in 500 fps, 3560 R (3100 F) air/propane combustion products and were operated satisfactorily for an excess of 100 hr and 40 thermal cycles which exceeded 2460 R (2000 F).

Franklin, Jerrold E.↗
NASA NTRS1991

Measurement of the performance of a spiral wound polyimide regenerator in a pulse tube refrigerator

A regenerator for use in a pulse tube refrigerator has been constructed from a polyimide (polypyromellitimide or PPMI) whose small ratio of thermal conductivity to heat capacity make it a good candidate for a regenerator material in cryocoolers. The regenerator was fabricated using 25 micron thick photoresist strips bonded to a 50 micron thick sheet of PPMI. This composite sheet was wound in jelly-roll fashion around a mandrel and inserted into the regenerator housing. The photoresist strips, formed using a photolithographic technique, provided a 25 micron spacing for the axial flow of gas between each layer of PPMI. Ineffectiveness results are presented for this material under actual operating conditions in a pulse tube refrigerator and compared with a numerical model. The numerical model indicated that a polyimide regenerator would perform much better than one constructed of stainless steel screen, but the experimental results showed the opposite behavior. Measured values for the ineffectiveness were 0.003 for the stainless steel screen and 0.017 for the polyimide.

Rawlins, Wayne↗
NASA NTRS1995

Analysis of conifer forest regeneration using Landsat Thematic Mapper data

Landsat Thematic Mapper (TM) data were used to evaluate young conifer stands in the western Cascade Mountains of Oregon. Regression and correlation analyses were used to describe the relationships between TM band values and age of young Douglas-fir stands (2 to 35 years old). Spectral data from well regenerated Douglas-fir stands were compared to those of poorly regenerated conifer stands. TM bands 1, 2, 3, 5, 6, and 7 were inversely correlated with the age (r greater than or equal to -0.80) of well regenerated Douglas-fir stands. Overall, the 'structural index' (TM 4/5 ratio) had the highest correlation to age of Douglas-fir stands (r = 0.96). Poorly regenerated stands were spectrally distinct from well regenerated Douglas-fir stands after the stands reached an age of approximately 15 years.

Fiorella, Maria↗
NASA NTRS1998

Myelinated sensory and alpha motor axon regeneration in peripheral nerve neuromas

Histochemical staining for carbonic anhydrase and cholinesterase (CE) activities was used to analyze sensory and motor axon regeneration, respectively, during neuroma formation in transected and tube-encapsulated peripheral nerves. Median-ulnar and sciatic nerves in the rodent model permitted testing whether a 4 cm greater distance of the motor neuron soma from axotomy site or intrinsic differences between motor and sensory neurons influenced regeneration and neuroma formation 10, 30, and 90 days later. Ventral root radiculotomy confirmed that CE-stained axons were 97% alpha motor axons. Distance significantly delayed axon regeneration. When distance was negligible, sensory axons grew out sooner than motor axons, but motor axons regenerated to a greater quantity. These results indicate regeneration differences between axon subtypes and suggest more extensive branching of motor axons within the neuroma. Thus, both distance from injury site to soma and inherent motor and sensory differences should be considered in peripheral nerve repair strategies.

Non-NASA Center↗
NASA NTRS1998

Hindlimb suspension reduces muscle regeneration

Exposure of juvenile skeletal muscle to a weightless environment reduces growth and satellite cell mitotic activity. However, the effect of a weightless environment on the satellite cell population during muscle repair remains unknown. Muscle injury was induced in rat soleus muscles using the myotoxic snake venom, notexin. Rats were placed into hindlimb-suspended or weightbearing groups for 10 days following injury. Cellular proliferation during regeneration was evaluated using 5-bromo-2'-deoxyuridine (BrdU) immunohistochemistry and image analysis. Hindlimb suspension reduced (P < 0.05) regenerated muscle mass, regenerated myofiber diameter, uninjured muscle mass, and uninjured myofiber diameter compared to weightbearing rats. Hindlimb suspension reduced (P < 0.05) BrdU labeling in uninjured soleus muscles compared to weight-bearing muscles. However, hindlimb suspension did not abolish muscle regeneration because myofibers formed in the injured soleus muscles of hindlimb-suspended rats, and BrdU labeling was equivalent (P > 0.10) on myofiber segments isolated from the soleus muscles of hindlimb-suspended and weightbearing rats following injury. Thus, hindlimb suspension (weightlessness) does not suppress satellite cell mitotic activity in regenerating muscles before myofiber formation, but reduces growth of the newly formed myofibers.

NASA Discipline Musculoskeletal↗
NASA NTRS1997

Myogenic regulatory factors during regeneration of skeletal muscle in young, adult, and old rats

Myogenic factor mRNA expression was examined during muscle regeneration after bupivacaine injection in Fischer 344/Brown Norway F1 rats aged 3, 18, and 31 mo of age (young, adult, and old, respectively). Mass of the tibialis anterior muscle in the young rats had recovered to control values by 21 days postbupivacaine injection but in adult and old rats remained 40% less than that of contralateral controls at 21 and 28 days of recovery. During muscle regeneration, myogenin mRNA was significantly increased in muscles of young, adult, and old rats 5 days after bupivacaine injection. Subsequently, myogenin mRNA levels in young rat muscle decreased to postinjection control values by day 21 but did not return to control values in 28-day regenerating muscles of adult and old rats. The expression of MyoD mRNA was also increased in muscles at day 5 of regeneration in young, adult, and old rats, decreased to control levels by day 14 in young and adult rats, and remained elevated in the old rats for 28 days. In summary, either a diminished ability to downregulate myogenin and MyoD mRNAs in regenerating muscle occurs in old rat muscles, or the continuing myogenic effort includes elevated expression of these mRNAs.

Non-NASA Center↗