Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REVERSED FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

A method for integrating the boundary-layer equations through a region of reverse flow.

Development of a procedure for numerically integrating the boundary-layer equations through a region of reverse flow which takes downstream influence into account. This method is applied to the problem of uniform flow past a parallel flat plate of finite length whose surface has a constant velocity directed opposite to that of the main stream. Although singularities occur at both the point of detachment (x sub s) and reattachment (x sub r) of the psi = 0 streamline, this integration technique provides a solution which ceases to apply only in the close proximity of these singular points. From this solution it is evident that, throughout a large portion of the separated region, the flow is strongly affected by conditions near x sub r, thereby demonstrating the importance of allowing information to be transmitted upstream in a region of backflow. Near x sub s, however, it is found that, in spite of the presence of reverse flow, the solution has a self-similar form in this particular example.

Klemp, J. B.↗
NASA NTRS1994

Compliant Metal Enhanced Convection Cooled Reverse-Flow Annular Combustor

A joint Army/NASA program was conducted to design, fabricate, and test an advanced, reverse-flow, small gas turbine combustor using a compliant metal enhanced (CME) convection wall cooling concept. The objectives of this effort were to develop a design method (basic design data base and analysis) for the CME cooling technique and tben demonstrate its application to an advanced cycle, small, reverse-flow combustor with 3000 F (1922 K) burner outlet temperature (BOT). The CME concept offers significant improvements in wall cooling effectiveness resulting in a large reduction in cooling air requirements. Therefore, more air is available for control of burner outlet temperature pattern in addition to the benefit of improved efficiency, reduced emissions, and smoke levels. Rig test results demonstrated the benefits and viability of the CME concept meeting or exceeding the aerothermal performance and liner wall temperature characteristics of similar lower temperature-rise combustors, achieving 0.15 pattern factor at 3000 F (1922 K) BOT, while utilizing approximately 80 percent less cooling air than conventional, film-cooled combustion systems.

Paskin, Marc D.↗
NASA NTRS1976

Properties of spikelike shear flow reversals observed in the auroral plasma by Atmosphere Explorer C

A study of the characteristics of pairs of oppositely directed spikes in ionospheric convection velocities (or shear flow reversals), as first described by Gurnett, has been conducted by using data from Atmosphere Explorer C. These phenomena tend to occur near the large-scale reversal from sunward to antisunward convection on the nightside of the earth. Generally, the spikelike shear flow reversals involve electric field components along the spacecraft orbit that are directed toward the region between them, in which inverted V type electron precipitation is observed. This relationship between the electron precipitation and the electric field spikes is consistent with an upward-flowing field-aligned current that is fed by Pedersen currents from the adjacent regions of strong convection. In one case a divergent equivalent electric field structure was observed, that is, with the spikelike electric fields pointing away from the region in between, which in this case exhibited a sharp electron flux dropout. This opposite configuration may be an example of counterparts to inverted V structures existing in regions of downward-flowing field-aligned currents.

Burch, J. L.↗
NASA NTRS1981

Effect of fuel injector type on performance and emissions of reverse-flow combustor

The combustion process in a reverse-flow combustor suitable for a small gas turbine engine was investigated to evaluate the effect of fuel injector type on performance and emissions. Fuel injector configurations using pressure-atomizing, spill-flow, air blast, and air-assist techniques were compared and evaluated on the basis of performance obtained in a full-scale experimental combustor operated at inlet conditions corresponding to takeoff, cruise, low power, and idle and typical of a 16:1-pressure-ratio turbine engine. Major differences in combustor performance and emissions characteristics were experienced with each injector type even though the aerodynamic configuration was common to most combustor models. Performance characteristics obtained with the various fuel injector types could not have been predicted from bench-test injector spray characteristics. The effect of the number of operating fuel injectors on performance and emissions is also presented.

Norgren, C. T.↗
NASA NTRS1968

Reversed flow in face seals.

Reversed laminar and turbulent flow in flat face seals, determining external fluid exchange across seal land using stream surfaces

Sneck, H. J.↗
NASA NTRS2008

Stagnation point reverse flow combustor

A method for combusting a combustible fuel includes providing a vessel having an opening near a proximate end and a closed distal end defining a combustion chamber. A combustible reactants mixture is presented into the combustion chamber. The combustible reactants mixture is ignited creating a flame and combustion products. The closed end of the combustion chamber is utilized for directing combustion products toward the opening of the combustion chamber creating a reverse flow of combustion products within the combustion chamber. The reverse flow of combustion products is intermixed with combustible reactants mixture to maintain the flame.

Zinn, Ben T.↗
DOE OSTI2025

De-Risking High-Recovery Brackish Water Desalination via Flow Reversal and Feed Flushing Using Techno-Economic Assessment

Novel desalination technologies have demonstrated enhanced performance and improved financial metrics over existing processes adopted by industry. Establishing quantitative performance targets is essential for achieving financial benefits over the current state of the art. Herein, we demonstrate how WaterTAP, a techno-economic assessment (TEA) tool, can be used to identify minimum performance metrics necessary to achieve financial benefit over using existing processes. This study evaluates the feasibility of increasing water recovery at the Chino Desalter I above 90 % through the addition of a third variable configuration reverse osmosis (VCRO) stage. Sensitivity analyses revealed flow reversal frequency, feed flushing volume (used as a cleaning step), and membrane lifespan are key factors influencing the financial viability of the VCRO process. The TEA analysis demonstrated that the system must achieve a recovery of 84 % and a 1-year membrane lifespan to have a breakeven LCOW, while achieving 90 % recovery can ultimately reduce the LCOW by 16 %. Notably, a trade-off between decreasing frictional losses and increased osmotic pressure across the recovery range, resulted in a stable specific energy consumption across the recovery range, enabling meaningful LCOW reductions without an energy penalty, a key finding that contrasts with conventional RO. This work demonstrates how TEA can guide system design by identifying key performance targets and exploring trade-offs, enabling data-driven decisions to de-risk innovative processes. These findings underscore the importance of leveraging TEA to evaluate scaling mitigation strategies and optimize inland desalination systems for sustainable and cost-effective operation.

14 SOLAR ENERGY↗
NASA NTRS1991

Leak detection of the Space Station Freedom U.S. Lab vacuum system using reverse flow leak detection methodology

A vacuum system leak detection technique (reverse flow leak detection) under development for use aboard Space Station Freedom is presented. The technique will be applied to the Vacuum System (VS) and Waste Gas Management Subsystem (WGMS) of the U.S. Lab Module. These two systems contain over 45.7 m of distributed vacuum tubing located in remote utility runs. Fluid flow calculations which utilize known system geometry and measured steady state pressure measurements from the VS and WGMS can be used to identify leak sites within +/- 38 cm. Exact leak position can then be pinpointed by conventional tracer gas leak detection in the identified region. Tests have been performed using a simple, unrestricted 12.8 m length of vacuum tubing with a calibrated air leak attached.

Moore, Jeffrey D.↗
NASA NTRS1974

Analysis of flow-reversal delay for a pitching airfoil

The coupled unsteady turbulent boundary layer and potential flow about a pitching airfoil are analyzed using numerical methods to determine the effect of pitch rate on the delay in forward movement of the rear flow reversal point. An explicit finite difference scheme is used to integrate the unsteady boundary layer equations, which are coupled at each instant of time to a fully unsteady and nonlinear potential flow analysis. A substantial delay in forward movement of the reversal point is demonstrated with increasing pitch rate, and it is shown that the delay results partly from the alleviation of the gradients in the potential flow, and partly from the effects of unsteadiness in the boundary layer itself.

Scruggs, R. M.↗
NASA NTRS1978

Reverse-flow combustor for small gas turbines with pressure-atomizing fuel injectors

A reverse flow combustor suitable for a small gas turbine (2 to 3 kg/s mass flow) was used to evalute the effect of pressure atomizing fuel injectors on combustor performance. In these tests an experimental combustor was designed to operate with 18 simplex pressure atomizing fuel injectors at sea level takeoff conditions. To improve performance at low power conditions, fuel was redistributed so that only every other injector was operational. Combustor performance, emissions, and liner temperature were compared over a range of pressure and inlet air temperatures corresponding to simulated idle, cruise, and takeoff conditions typical of a 16 to 1 pressure ratio turbine engine.

Norgren, C. T.↗
NASA NTRS1985

Dilution jet configurations in a reverse flow combustor

Results of measurements of both temperature and velocity fields within a reverse flow combustor are presented. Flow within the combustor is acted upon by perpendicularly injected cooling jets introduced at three different locations along the inner and outer walls of the combustor. Each experiment is typified by a group of parameters: density ratio, momentum ratio, spacing ratio, and confinement parameter. Measurements of both temperature and velocity are presented in terms of normalized profiles at azimuthal positions through the turn section of the combustion chamber. Jet trajectories defined by minimum temperature and maximum velocity give a qualitative indication of the location of the jet within the cross flow. Results of a model from a previous temperature study are presented in some of the plots of data from this work.

Zizelman, J.↗
NASA NTRS1972

High Pressure Reverse Flow APS Engine

A design and test demonstration effort was undertaken to evaluate the concept of the reverse flow engine for the APS engine application. The 1500 lb (6672 N) thrust engine was designed to operate on gaseous hydrogen and gaseous oxygen propellants at a mixture ratio of 4 and to achieve the objective performance of 435 sec (4266 Nsec/kg) specific impulse. Superimposed durability requirements called for a million-cycle capability with 50 hours duration. The program was undertaken as a series of tasks including the initial preliminary design, design of critical test components and finally, the design and demonstration of an altitude engine which could be used interchangeably to examine operating parameters as well as to demonstrate the capability of the concept. The program results are reported with data to indicate that all of the program objectives were met or exceeded within the course of testing on the program. The analysis effort undertaken is also reported in detail and supplemented with test data in some cases where prior definitions could not be made. The results are contained of these analyses as well as the test results conducted throughout the course of the program. Finally, the test data and analytical results were combined to allow recommendations for a flight weight design. This preliminary design effort is also detailed.

Senneff, J. M.↗
NASA NTRS1983

Effect of broad properties fuel on injector performance in a reverse flow combustor

The effect of fuel type on the performance of various fuel injectors was investigated in a reverse flow combustor. Combustor performance and emissions are documented for simplex pressure atomizing, spill flow, and airblast fuel injectors using a broad properties fuel and compared with performance using Jet A fuel. Test conditions simulated a range of flight conditions including sea level take off, low and high altitude cruise, as well as a parametric evaluation of the effect of increased combustor loading. The baseline simplex injector produced higher emission levels with corresponding lower combustion efficiency with the broad properties fuel. There was little or not loss in performance by the two advanced concept injectors with the broad properties fuel. The airblast injector proved to be especially insensitive to fuel type.

Raddlebaugh, S. M.↗
NASA NTRS1982

Dilution Jet Behavior in the Turn Section of a Reverse Flow Combuster

Measurements of the temperature field produced by a single jet and a row of dilution jets issued into a reverse flow combustor are presented. The temperature measurements are presented in the form of consecutive normalized temperature profiles, and jet trajectories. Single jet trajectories were swept toward the inner wall of the turn, whether injection was from the inner or outer wall. This behavior is explained by the radially inward velocity component necessary to support irrotational flow through the turn. Comparison between experimental results and model calculations showed poor agreement due to the model's not including the radial velocity component. A widely spaced row of jets produced trajectories similar to single jets at similar test conditions, but as spacing ratio was reduced, penetration was reduced to the point where the dilution jet flow attached to the wall.

Riddlebaugh, S. M.↗
NASA NTRS1982

Dilution jet behavior in the turn section of a reverse flow combustor

Measurements of the temperature field produced by a single jet and a row of dilution jets issued into a reverse flow combustor are presented. The temperature measurements are presented in the form of consecutive normalized temperature profiles, and jet trajectories. Single jet trajectories were swept toward the inner wall of the turn, whether injection was from the inner or outer wall. This behavior is explained by the radially inward velocity component necessary to support irrotational flow through the turn. Comparison between experimental results and model calculations showed poor agreement due to the model's not including the radial velocity component. A widely spaced row of jets produced trajectories similar to single jets at similar test conditions, but as spacing ratio was reduced, penetration was reduced to the point where the dilution jet flow attached to the wall.

Riddlebaugh, S. M.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of airfoil sections with rounded trailing edges in forward and reverse flow

Low-speed wind-tunnel tests were conducted to determine the two-dimensional aerodynamic characteristics of 6-, 12-, and 18-percent-thick airfoil sections with rounded trailing edges in both forward and reverse flow. The shapes incorporated camber with both the leading and trailing edges rounded to provide reasonable aerodynamic performance with either edge directed toward the free-stream flow. The tests were conducted with the airfoils in both normal and reverse orientations relative to the free stream. The Mach number was varied from 0.16 to 0.36 and the angle of attack was varied from minus 10 to 24 million. Reynolds number, based on the airfoil chord, was varied from about 1.0 to 12.0 million.

Beasley, W. D.↗
NASA NTRS1942

Pressure distribution on wings in reversed flow

The series of pressure distribution measurements at three test sections on NACA airfoils 2212 and M6 within 170 to 210 angles of attack in reversed flow proved to be largely independent of the profile form. In contradiction to the pressure distribution in normal flow considerable negative pressure from the upper surface spills over onto the lower surface, and vice versa, even in the zone of sound flow. The results are presented as chord-wise pressure and load distribution. The spanwise lift distribution and the total lift coefficients of the wing obtained by integration manifest approximate agreement with the behavior of a diagonally disposed flat plate. By consideration of the ground effect (represented by a flat wall) the lower surface of the wing shows an increase in the low pressure.

Naumann, A↗