Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Estimating Vadose Zone Flow Properties at the 100 K-East Soil Flushing Site Using ERT Monitoring Data: 2023 Interim Report - 100 KE Soil Property Estimation

In situ soil flushing is being using at the Hanford 100 K-East (100 KE) area to transport mobile chromium contamination in the vadose zone to the water table, where it can be collected and treat through pump and treat operations. The efficacy of soil flushing is directly related to the volume of clean water that infiltrates through contaminated soils. In practice, it is infeasible to comprehensively monitor which regions of the vadose zone are being infiltrated through direct sampling of pore water. Consequently, there can be significant uncertainty about which regions of the subsurface have been treated, especially if hydrogeologic conditions are favorable for the development of unstable flows and preferred flow pathways through the vadose zone (Jarvis, Koestel, and Larsbo 2016). Current approaches for quantitative monitoring of soil flushing performance rely on contaminant concentration measurements collected from extractions wells. There is no quantitative information on the volume of flush water delivered to targeted regions of the vadose zone at the Hanford Site, leading to significant uncertainty regarding source term removal and long-term impacts to groundwater. If the subsurface hydrogeologic properties at the 100 KE Area were adequately known, qualitative metrics of soil flushing performance could be simulated, thereby negating expenses required to obtain quantitative performance information through borehole drilling/sampling. However, estimating in situ hydrogeologic properties has long proven elusive, due primarily to a lack of sufficient information to constrain heterogeneous property estimates to a useful degree of certainty. Estimating vadose zone hydrogeologic properties is particularly challenging due the dependence of hydraulic conductivity on saturation. This report describes progress toward a first-of-its-kind demonstration using surface time-lapse 3D electrical resistivity tomography (ERT) monitoring data to estimate the hydrogeologic properties that control flush water transport at the 100 KE soil flushing site. The ultimate objective is (1) to verify sufficient information exists in the ERT monitoring data to adequately resolve vadose zone hydraulic properties, and (2) generate a “digital twin” (i.e., a numerical simulator) that can be used to simulate the amount of flush water that has been delivered to each targeted region of the vadose zone, and thereby assess the efficacy of flush water delivery. Resulting performance estimates can be used in leu of comprehensive borehole drilling and direct sampling (or wellbore logging) that would otherwise be required to obtain the same information.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Exploring biofiber properties and their influence on biocomposite tensile properties

Biofibers serve as effective reinforcements for neat polylactic acid (PLA) in biocomposites, offering an attractive opportunity to decarbonize the manufacturing sector of the United States by displacing fossil-based reinforcement fibers such as carbon fibers. Also, biofiber production can stimulate economic growth in rural economies, fueling sustainable development. PLA resins are commonly compounded with biofibers to create biocomposites suitable for additive manufacturing. PLA-biofiber composites often exhibit better overall material properties than neat (pure) PLA, but the associations between biofiber properties and the material properties of their biocomposites remain largely unexplored. Hence, this research delves into a comprehensive exploration of diverse biofibers, scrutinizing their physical and chemical attributes, including size, shape, ash content and biochemical composition. The study meticulously analyzes the flow properties of each biofiber and elucidates the ultimate tensile strengths and Young's modulus of corresponding biocomposite samples. Noteworthy correlations between biofiber and biocomposite tensile properties are uncovered, shedding light on critical interrelationships. The study introduces an approach employing regression models to predict the ultimate tensile strength and Young's modulus of biocomposites. These models, validated with a cross-validation technique, exhibit remarkable predictive accuracy, particularly in estimating ultimate tensile strength. © 2024 Oak Ridge National Laboratory managed by UT-Battelle, LLC and The Author(s). Polymer International published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Understanding the effect of specimen size on the properties of fine-grain isotropic nuclear graphite for irradiation studies: Physical, electrical, thermal properties

Programs at Oak Ridge National Laboratory are investigating the effects of neutron irradiation in the High Flux Isotope Reactor (HFIR) on properties of fine-grain nuclear graphites. Specimens were irradiated in the HFIR flux trap, which required using specimens that are smaller than the sizes recommended by ASTM standards. Here, this work has investigated whether subsized specimens can be used to reliably determine the measured physical (density, elastic moduli, and electrical resistivity) and thermal properties (coefficient of thermal conductivity and thermal conductivity). The results show the specimen sizes in this investigation had a minimal influence on any of the measured properties. Even for the properties where size influenced the measured value (density and thermal conductivity), an explanation is provided, and the consequences can be accounted for in post-irradiation results. This work demonstrated that using subsized specimens for physical and thermal property measurements is suitable when necessary for fine-grain isotropic graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ab initio Molecular Dynamics Assessment of Thermodynamic and Transport Properties in (K,Li)Cl and (K, Na)Cl Molten Salt Mixtures

Molten salt mixtures are integral part of highly important technological applications such as nuclear reactors. However, due to inherent difficulties associated with experiment at high temperatures and the intrinsic complexity of liquid-phase multi-component systems, understanding their properties at a molecular level remains a challenge. Here, we report on an ab initio molecular dynamics investigation on structural, electronic, transport, and thermal properties of two common molten salt mixtures, (K, Li)Cl and (K,Na)Cl, at five different compositions and three temperatures. Most of the properties were found to depend on both composition and temperature. While properties, like atomic charges, show additive behaviors, other properties, such as electrical conductivity, show considerable deviations from additivity. We shall show that the mixing of the molten salt mixtures is mainly driven by entropy, and that the KCl and LiCl mix better than KCl and NaCl. Our computational results are in general consistent with available experimental data. Comparison with available theoretical data is also provided.

Nguyen, Manh Thuong↗
DOE OSTI2021

Bridging the Void: Halogen Bonding and Aromatic Interactions to Program Luminescence and Electronic Properties of π -Conjugated Materials in the Solid State

π-Conjugated materials are promising candidates for emerging organic optoelectronic devices empowered by molecular design. The unsolved challenges of predicting and controlling their packing as solids, central to their properties and performance, currently limits their practical application. As noncovalent interactions drive packing, control over such interactions are critical to bridging from chemical structure to functional properties. In molecular crystals, halogen bonding and interactions of aromatic rings have emerged as versatile tools for noncovalent control with tailored luminescence and electronic properties. Here, we describe how the interplay of these directional and tunable interactions can engineer properties, including stimuli-responsive behavior. Specifically, halogen bonding can provide robust designs for directing 2D molecular assembly, whereas the intentional interactions of aromatic rings can yield metastable, switchable packing modes, as well as programmed stacking between layers of chromophores. Examples, herein, demonstrate clear relationships between assembly by design and resulting solid-state properties, and strategies presented offer guidance for future designs of π-conjugated molecular materials using specific aromatic interactions and halogen bonding.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Soils' dirty little secret: Depth–based comparisons can be inadequate for quantifying changes in soil organic carbon and other mineral soil properties

Quantifying changes in soil organic carbon (SOC) stocks and other soil properties is essential for understanding how soils will respond to land management practices and global change. Although they are widely used, comparisons of SOC stocks at fixed depth (FD) intervals are subject to errors when changes in bulk density or soil organic matter occur. The equivalent soil mass (ESM) method has been recommended in lieu of FD for assessing changes in SOC stocks in mineral soils, but ESM remains underutilized for SOC stocks and has rarely been used for other soil properties. In this paper, we draw attention to the limitations of the FD method and demonstrate the advantages of the ESM approach. We provide illustrations to show that the FD approach is susceptible to errors not only for quantifying SOC stocks but also for soil mass-based properties such as SOC mass percent, C:N mass ratio, and δ 13 C. Here we describe the ESM approach and show how it mitigates the FD method limitations. Using bulk density change simulations applied to an empirical dataset from bioenergy cropping systems, we show that the ESM method provides consistently lower errors than FD when quantifying changes in SOC stocks and other soil properties. To simplify the use of ESM, we detail how the method can be integrated into sampling schemes, and we provide an example R computer script that can perform ESM calculations on large datasets. We encourage future studies, whether temporal or comparative, to utilize sampling methods that are amenable to the ESM approach. Overall, we agree with previous recommendations that ESM should be the standard method for evaluating SOC stock changes in mineral soils, but we further suggest that ESM may also be preferred for comparisons of other soil properties including mass percentages, elemental mass ratios, and stable isotope composition.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Mechanical properties of Zircaloy cladding tubes and contributions to M.E.T.A. mechanical property database

To support a multi-laboratory Methodology, Evaluation, Testing, and Analysis (M.E.T.A.) cladding properties database, Oak Ridge National Laboratory’s (ORNL’s) cladding mechanical test geometries were manufactured from several nuclear-relevant cladding alloys and subsequently tested. These geometries were developed as mechanical test specimens to evaluate the properties of tube materials that may be used for irradiation testing at ORNL’s High Flux Isotope Reactor. They may also be used as test articles to be harvested—via in-cell machining—from commercially irradiated fuel rods and later tested. This report explores the differences among axial, hoop, and SSJ tensile geometries with partially recrystallized Zircaloy-2 to test ORNL correlation-based methods on a plate material that approximates, to the greatest extent possible, the characteristics of nuclear industry tubing. Furthermore, several tests were conducted with ORNL’s Zircaloy-4 tube inventory to (1) develop material properties as a standard for future tests, (2) determine the effect of the US Department of Energy’s Advanced Fuels Campaign coating processes on tube mechanical properties, and (3) evaluate the effect of specimen machining methods on the mechanical properties of tube geometries.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Thermal Properties of Sodium Borosilicate Glasses as a Function of Sulfur Content

SO3 additions, up to 3.0 wt%, were systematically investigated for effects on the physical properties of sodium borosilicate glass melted in air, with a sulfur-free composition of 50SiO2-10Al2O3-12B2O3-21Na2O-7CaO (wt%). Solubility measurements, using electron microscopy chemical analysis, determined the maximum loading to be ~1.5 wt% SO3. It was found that sulfur (here as sulfate) in this glass increased the glass transition temperature, thermal diffusivity, heat capacity, and thermal conductivity, and decreased the mass density. Structural analysis, performed with Raman spectroscopy, indicated that the borosilicate network polymerized with sulfur additions, presumably due to Na2O being required to charge compensate the ionic SO42- additions, thus becoming unavailable to form non-bridging oxygen in the silicate network. It is postulated that this increased crosslinking of the borosilicate backbone lead to a structure with higher dimensionality and average bond energy. This increased the mean free paths and vibration frequency of the phonons, which resulted in the observed increase in thermal properties.

Thermal properties, Borosilicate glass, Sulfur sol↗
DOE OSTI2022

Catalyst design to direct high-octane gasoline fuel properties for improved engine efficiency

The paraffin-to-olefin (P/O) ratio in gasoline fuel is a critical metric affecting fuel properties and engine efficiency. In the conversion of dimethyl ether (DME) to high-octane hydrocarbons over BEA zeolite catalysts, the P/O ratio can be controlled through catalyst design. Here, we report bimetallic catalysts that balance the net hydrogenation and dehydrogenation activity during DME homologation. The Cu-Zn/BEA catalyst exhibited greater relative dehydrogenation activity attributed to higher ionic site density, resulting in a lower P/O ratio (6.6) versus the benchmark Cu/BEA (9.4). The Cu-Ni/BEA catalyst exhibited increased hydrogenation due to reduced Ni species, resulting in a higher P/O ratio (19). The product fuel properties were estimated with an efficiency merit function and compared against finished gasolines and a typical alkylate blendstock. Merit values for the hydrocarbon product from all three BEA catalysts exceeded those of the comparison fuels (0–5.3), with the product from Cu-Zn/BEA exhibiting the highest merit value (9.7).

Catalyst design↗
DOE OSTI2020

Production and Fuel properties of Iso-Olefins with Controlled Molecular Structure and Obtained from Butene Oligomerization

The ability to control the molecular structure (e.g., degree of branching) of iso-olefins produced from oligomerizing light olefins is a valuable tool for tuning the final compositions of hydrocarbon fuels and targeting specific fuel properties. In this study, we demonstrated that the degree of branching of iso-olefins obtained from butene(s) oligomerization can be controlled by tuning process conditions (i.e., temperature, weight hourly space velocity [WHSV], and nature of butene feedstock) and by choosing the proper catalyst (i.e., Amberlyst-36 vs. Y/ZSM-22). In this study, we produced three types of iso-olefin mixtures: 1) a methyl-heptenes rich (74 wt.%) mixture, 2) dimethyl-hexenes rich (80–96 wt.%) mixtures, and 3) highly branched (i.e., more than three methyl substitutions) iso-olefins rich (>50 wt.%) mixtures. While dimethyl-hexenes are preferentially formed at lower temperatures (60–100°C) and WHSV (i.e., 2 hr-1), methyl-heptenes are favorably produced at higher temperatures (>100°C) and WHSVs (i.e., 7 hr-1) over Amberlyst-36. The use of either 1-butene or 2-butene as feedstock resulted in liquid products with similar branching because facile intramolecular isomerization occurs prior to oligomerization. However, the use of isobutylene feedstock forms a significantly more branched olefin product. The formation of highly branched iso-olefins also is favored at higher temperature (140°C) over Amberlyst-36. Using Y/ZSM-22 instead of Amberlyst-36 allowed preferential formation of less-branched methyl-heptenes. For each type of iso-olefins mixture, we determined fuel properties including research octane number (RON), motor octane number (MON), and octane sensitivity (S), which is the difference between RON and MON. We found that not only RON and MON but also S values increased with the degree of branching of these complex mixtures of iso-olefins. The highest RON of 99.7 and S value of 9.3 were obtained for a mixture of highly branched iso-olefins.

Dagle, Vanessa↗
DOE OSTI2024

Use of a Lignin-Based Admixture for Tailoring the Rheological Properties of Mortars for 3D Printing: Preprint

Efforts toward decarbonizing construction materials and industrial processes related to cement and concrete can be aided via multifaceted approaches that target alternative admixtures as well as precision control of fabrication. Chemical admixtures for water reduction have played a crucial role in the development of advanced concrete mixtures. Newer biomass processing techniques developed for aviation fuel production from corn stover biomass produce a more reactive lignin byproduct that is suitable for chemical modifications to mimic the properties of polycarboxylate ether admixtures with a smaller carbon footprint. The present study examines the use of lignin-based water-reducing admixture in cement pastes and mortar mixtures for 3D printing. The experimental program explores the use of different dosages of lignin-based admixture to produce 3D-printed samples with appropriate extrudability and buildability. The rheological characterization was performed to determine the flow curve of various mixtures. Finally, the heat of hydration of cement pastes was monitored via isothermal calorimetry to assess the impact of lignin-based admixtures on the hydration process of cement. The results of this study indicate that the use of biomass by-products, such as lignin-based admixtures have great potential to effectively control the fresh-state properties of cement-based materials.

bio-based admixtures↗
DOE OSTI2022

Fuel Properties of Oxymethylene Ethers with Terminating Groups from Methyl to Butyl

Oxymethylene ethers (OMEs) have been studied as possible additives or replacements for diesel fuels. Typically, studies have considered only methyl-terminated OMEs. Recent structure-property relationship models suggest that extended-alkyl OMEs may provide improvements to many of the properties of methyl-terminated OMEs that make them less suitable as diesel fuel blendstocks. In this work, we describe the synthesis and characterization of 16 different OMEs with methyl, ethyl, propyl, butyl, isopropyl, and isobutyl terminating alkyl groups with varying oxymethylene chain length. Indicated Cetane Number, Lower Heating Value, Flash Point, Density, Viscosity, Vapor Pressure, and Oxidative Stability are tested via ASTM standard methods. Additionally, Water Solubility, Boiling Point, seal material compatibility, and sooting propensity (via the Yield Sooting Index) are measured for these fuels. For diesel compatibility, all tested OMEs except smaller methyl and ethyl OMEs, and the branched isopropyl OME, meet cetane number requirements. Further, extending the alkyl end group increases the heating value, but all OMEs, due to their oxygen content, have heating values less than diesel; despite this, all OMEs show significant reductions in soot production per unit heating value. Only the heaviest OMEs meet diesel viscosity requirements, and most are higher density than diesel. OMEs with larger alkyl groups show the highest stability under accelerated auto-oxidation conditions. Increases in alkyl group length cause order of magnitude reduction in water solubility, from hundreds of g/L for methyl terminated OMEs to hundreds of mg/L for butyl terminated OMEs. Limited seal material testing indicates that PEEK polymers are unaffected by OMEs; while extended alkyl groups may improve compatibility with FKM (Viton), other common elastomers (NBR, silicone) remain incompatible with all tested OMEs. Overall, it is found that methyl-terminated OMEs exhibit the most potential for soot reduction, but OMEs with larger propyl and butyl terminating alkyl groups show improved compatibility with existing diesel systems.

09 BIOMASS FUELS↗
DOE OSTI2020

Effects of Intercalating Molecules on the Polymer Properties of DNA

Atomic force microscopy (AFM) enables determination of physical properties from single DNA molecules. Insertion of aromatic molecules into the structure of DNA results in morphological changes. However, the accompanying changes to elastic properties due to this insertion are not fully understood. AFM was used to examine the morphological effects of intercalator binding and report changes in the elastic properties of intrinsically straight DNA molecules. The persistence length and polymer extension were characterized in the presence of three intercalating molecules: ethidium bromide and the less well studied chloroquine and acridine. It was found that all three intercalators significantly increased the bending persistence length. In addition, an analysis of the normal bending modes of the static molecules corroborated these results. Furthermore, this approach of measuring binding effects of intercalators on DNA physical properties using a model system of intrinsically straight DNA is applicable to other DNA binding ligands and other modes of DNA interaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Rethinking the magnetic properties of lepidocrocite: A density functional theory and cluster expansion study

The iron oxyhydroxide lepidocrocite (g-FeOOH) is an abundant mineral critical to a number of chemical and technological applications. Of particular interest is the ground state and nite temperature magnetic order, and the subsequent impact this has upon crystal properties. The magnetic properties, investigated in this work are governed primarily through superexchange interactions, and have been calculated using density functional theory and cluster expansion methods. Quantication of these exchange terms has facilitated the determination of the ground state magneto-crystalline structure and subsequent calculation of its lattice constants, elastic moduli, cohesive enthalpy, and electronic density of states. Further, using a collinear magnetic conguration model, the magnetic heat capacity versus temperature has been studied and the Neel temperature obtained.

Pope, Daniel J.↗
DOE OSTI2020

Viscous flow properties and hydrodynamic diameter of phenothiazine-based redox-active molecules in different supporting salt environments

We report viscous flow properties of a redox-active organic molecule, N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT), a candidate for non-aqueous redox flow batteries, and two of its radical cation salts. A microfluidic viscometer enabled the use of small sample volumes in determining viscosity as a function of shear rate and concentration in the non-aqueous solvent, acetonitrile, both with and without supporting salts. All solutions tested show Newtonian behavior over shear rates of up to 30 000 s−1, which was rationalized by scaling arguments for the diffusion-based relaxation time of a single MEEPT molecule without aggregation. Neat MEEPT is flowable but with a large viscosity (412 mPa⋅s at room temperature), which is ∼1000 times larger than that of acetonitrile. MEEPT solutions in acetonitrile have low viscosities; at concentrations up to 0.5 M, the viscosity increases by less than a factor of two. From concentration-dependent viscosity measurements, molecular information was inferred from intrinsic viscosity (hydrodynamic diameter) and the Huggins coefficient (interactions). Model fit credibility was assessed using the Bayesian Information Criterion. It is found that the MEEPT and its charged cations are “flowable” and do not flocculate at concentrations up to 0.5 M. MEEPT has a hydrodynamic diameter of around 8.5 Å, which is almost insensitive to supporting salt and state of charge. This size is comparable to molecular dimensions of single molecules obtained from optimized structures using density functional theory calculations. The results suggest that MEEPT is a promising candidate for redox flow batteries in terms of its viscous flow properties.

Wang, Yilin (ORCID:0000000316102995)↗
DOE OSTI2021

Structure-property correlations and scaling in the magnetic and magnetocaloric properties of GdCrO 3 particles

The structure, magnetic, and magnetocaloric (MC) properties of orthorhombic nanocrystalline GdCrO 3 with six particle sizes: < d > = 87, 103, 145, 224, 318, and 352 nm are reported. The particle size was tailored by annealing under different temperatures and estimated by scanning electron microscopy. With increase in < d >, Goldschmidt tolerance factor t, orthorhombic strain s, and out-of-plane Cr–O 1 –Cr bond angle first decrease, reaching minimum values for < d > = 224 nm, and then increase for sample with < d > = 318 nm and 352 nm, thus showing a V-shaped variation. Temperature dependence of the magnetization (M) reveals an antiferromagnetic transition at ${T}_{\text{N}}^{\text{Cr}}\sim 168$ K for < d > ≥ 224 nm and ${T}_{\text{N}}^{\text{Cr}}\sim 167$ K for < d > < 224 nm and an essentially d-independent spin-reorientation at T SR = 9 K. M measured at 5 K and 7 T first increases with increase in < d >, reaching maximum value for sample with < d > = 224 nm, and then decreases for samples with < d > = 318 nm and 352 nm, showing an inverted-V variation with < d >. Similar < d >-dependence is observed for the magnetic entropy change (MEC) and relative cooling power (RCP) showing a close relationship between the structural and magnetic properties of GdCrO 3 nanoparticles investigated here. The 224 nm sample with the minimum values of t, s, and Cr–O 1 –Cr bond angle exhibits the maximum value of MEC (–ΔS) = 37.8 J kg –1 K –1 at 5 K under a field variation (ΔH) of 7 T and its large estimated RCP of 623.6 J Kg –1 is comparable with those of typical MC materials. Both (–ΔS) and RCP are shown to scale with the saturation magnetization MS, suggesting that MS is the crucial factor controlling their magnitudes. Assuming (–ΔS) ~ (ΔH) n , the temperature dependence of n for the six samples are determined, n varying between 1.3 at 5 K to n = 2.2 at 130 K in line with its expected magnitudes based on mean-field theory. Furthermore, these results on structure-property correlations and scaling in GdCrO 3 suggest that its MC properties are tunable for potential low-temperature magnetic refrigeration applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗