Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Membrane Contactors for Ammonia Recovery from Anaerobic Digester Centrate: Pretreatment and Process Optimization

Haber-Bosch process allows for the production of modern fertilizers and is crucial for meeting increasing demands for agricultural production. The process requires large amounts of natural gas and contributes to global warming. An alternative to the Haber-Bosch process utilizes membrane contactors to recover nitrogen from the anaerobic digester centrate. In previous studies, high recoveries have been achieved, but membrane fouling decreased the performance and required maintenance to clean the membranes. Furthermore, this study investigated the effect of a settling and ultrafiltration system to pretreat centrate from an anaerobic digester to prevent fouling of the membrane contactor system. The system achieved high recoveries of over 90% for 10 cycles without any performance decline. Tests with increasing distillate concentrations of ammonium sulfate up to 165,000 mg/L-N could not identify a significant decline in membrane performance either. This allows for concentration up to crystallization in a single stage.

09 BIOMASS FUELS↗
DOE OSTI2025

Process Optimization and Modeling for Minerals Sustainability (PrOMMiS) v1.0.0

The U.S. Department of Energy's ("DOE") Process Optimization and Modeling for Minerals Sustainability project ("PrOMMiS Project") was initiated in 2023 to transform the national Critical Minerals and Rare Earth Elements (CM & REE) landscape, thereby supporting DOE's three enduring strategic objectives: security, economic competitiveness, and environmental responsibility. To address this initiative, the PrOMMiS Project will develop, demonstrate, and deploy an open-source, advanced system modeling, optimization, and analysis application ("PrOMMiS Software Application") that will support industry decision-makers by accelerating the scale-up of novel CM & REE technologies by de-risking the development and deployment of commercial scale processes and maximizing learning throughout the development cycle.

Beattie, KeithS [Lawrence Berkeley National Labora↗
DOE OSTI2024

Improving Additive Manufactured Component Performance through Multi-Scale Microstructure Simulation and Process Optimization

The purpose of this project was to utilize computational tools to understand the relationships between processing, microstructure, and properties for additively manufactured (AM) aluminum alloys for automotive applications, and to provide an engineering solution for helping to optimize process conditions. The project leverages ORNL developments in computational modeling, including AM process modeling, phase-field based microstructure evolution predictions, and data analytics techniques for mapping process conditions to material outcomes. The project utilized an Al-Cu-Mn-Zr alloy as a model material for studying formation of defects and microstructural features in response to variations in process conditions. Based on both pre-existing experimental data and simulation results, statistical process maps were constructed to identify regions of process space with minimal defect formation and advantageous microstructures and properties. The software tools used for this purpose were successful disseminated to GM, who were able to successful compile the relevant HPC codes within their own computing ecosystem and perform initial calculations to reproduce ORNL results.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Active learning using hybrid surrogate tool life modeling for machining process optimization

Here, this paper describes an active learning approach for part-to-part iterative machining process optimization using a hybrid surrogate tool life model. A probabilistic interpolating tool life model is developed by combining the empirical Taylor-type tool life equation and the model fit error. The probabilistic tool life model is then used to calculate the machining cost per part distribution. The optimal machining parameters are selected using an expected improvement in machining cost per part criterion. The method is validated numerically using experimental results; the results show a median convergence error of 2.2% after three tests over 400 simulations. The method is validated experimentally on two industrial applications for Ti-6Al-4V roughing resulting in a cost per part reduction greater than 23% after two tests. The described method is a robust solution for rapid convergence to optimal machining parameters in an industrial production environment.

Active learning↗
NASA NTRS1991

Analytical modeling and sensor monitoring for optimal processing of polymeric composite material systems

Process simulation models and cure monitoring sensors are discussed for use in optimal processing of fiber-reinforced composites. Analytical models relate the specified temperature and pressure cure cycle to the thermal, chemical, and physical processes occurring in the composite during consolidation and cure. Frequency-dependent electromagnetic sensing (FDEMS) is described as an in situ sensor for monitoring the composite curing process and for verification of process simulation models. A model for resin transfer molding of textile composites is used to illustrate the predictive capabilities of a process simulation model. The model is used to calculate the resin infiltration time, fiber volume fraction, resin viscosity, and resin degree of cure. Results of the model are compared with in situ FDEMS measurements.

Loos, Alfred C.↗
DOE OSTI2024

Process Optimization of Carbon Electrode Materials Manufacturing by Experimental Study and Machine Learning Techniques

Electrospun carbon fibers from coal have been investigated as electrodes for batteries and supercapacitors. Despite the excellent properties of coal-derived carbon fibers (CCNF) for energy storage devices, there still lacks systematic understanding on how various process parameters affect final electrode performances, which poses challenges to scale from pilot to high volume manufacturing. The goals of this project are twofold. First, we focuse on process optimization for converting a new precursor from powder river basin (PRB) coal, referred to as coal-based polyurethane (CPU) to CCNF using electrospinning. Second, different machine learning techniques will be examined using experimental data from this work and open literature. Specifically, for CPU the following process parameters need to be characterized and optimized in order to produce CCNFs with desirable mechanical integrity and physiochemical properties: precursor composition and viscosity, operating voltage and distance, oxidation and carbonization temperature and duration. Consequently, physiochemical properties of the fibers were characterized to correlate these process parameters with desirable electrochemical performance. Given the complex nature of the fiber production process, ML models are assessed for their ability to capture the nonlinear relationship between process parameters and the electrochemical properties in applications including supercapacitors. As such, we applied various machine learning techniques, to determine which technique produces a model that best predicts device function.

Cincotta, Robert E.F.↗
NASA NTRS1984

Optimization process in helicopter design

In optimizing a helicopter configuration, Hughes Helicopters uses a program called Computer Aided Sizing of Helicopters (CASH), written and updated over the past ten years, and used as an important part of the preliminary design process of the AH-64. First, measures of effectiveness must be supplied to define the mission characteristics of the helicopter to be designed. Then CASH allows the designer to rapidly and automatically develop the basic size of the helicopter (or other rotorcraft) for the given mission. This enables the designer and management to assess the various tradeoffs and to quickly determine the optimum configuration.

Logan, A. H.↗
DOE OSTI2022

Data-driven simultaneous process optimization and adsorbent selection for vacuum pressure swing adsorption

Technologies for post-combustion carbon capture are essential for the reduction of greenhouse gas emissions to the atmosphere. However, they are still associated with high costs and energy consumption. Intensified processes for carbon capture have the potential to overcome these challenges due to their higher efficiency, lower capital cost, and increased operational flexibility. Here, this work investigates simultaneous optimization of process conditions and adsorbent selection for a modular Vacuum Pressure-Swing Adsorption system designed for CO 2 capture. Both surrogate-based Nonlinear Programming and Mixed-Integer Nonlinear Programming approaches are applied and compared in terms of computational efficiency and solution accuracy. Moreover, process performance results are examined by applying several data analytics techniques to gain insights into the material-process correlations. Data-driven classifiers and neural networks can accurately predict whether a material is likely to satisfy purity, recovery, and energy constraints when operated at optimal process conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Multi-physics melt pool modeling and process optimization for laser direct energy deposition of Nb-based refractory C103: Defect formation, geometric precision, and process mapping

Recent developments in additive manufacturing (AM) technology have reignited interest in the fabrication of the Nb-based refractory C103 alloy offering solutions to the challenges posed by traditional manufacturing methods. However, the limited numerical and experimental studies on laser direct energy deposition (DED) of C103 have hindered the understanding of the relationships between process parameters and build quality. This has made it challenging to consistently produce parts with the desired quality and microstructure suitable for critical applications. In this study, we focus on optimizing the laser DED process for C103 by employing a hybrid approach that combines experimental techniques and computational fluid dynamics (CFD). This approach facilitates the development of process maps for defect detection and geometric precision. To achieve this, multi-layer C103 samples were fabricated using laser DED under various process parameters, enabling the creation of a process map for defect detection. Additionally, a multi-physics, multiphase simulation framework was developed within a high-performance computing (HPC) environment to establish process maps for geometric precision. Using these process maps, printability windows were identified for achieving both the desired geometric accuracy and defect-free prints. It was observed that prints with a power-to-velocity (P/V) ratio close to unity resulted in defect-free outcomes. This study provides a foundation for reducing design lead time and rejected parts, ultimately optimizing the laser DED process for C103.

Defect formation and geometric precision↗
NASA NTRS2016

Further Development and Assessment of a Broadband Liner Optimization Process

The utilization of advanced fan designs (including higher bypass ratios) and shorter engine nacelles has highlighted a need for increased fan noise reduction over a broader frequency range. Thus, improved broadband liner designs must account for these constraints and, where applicable, take advantage of advanced manufacturing techniques that have opened new possibilities for novel configurations. This work focuses on the use of an established broadband acoustic liner optimization process to design a variable-depth, multi-degree of freedom liner for a high speed fan. Specifically, in-duct attenuation predictions with a statistical source model are used to obtain optimum impedance spectra over the conditions of interest. The predicted optimum impedance information is then used with acoustic liner modeling tools to design a liner aimed at producing impedance spectra that most closely match the predicted optimum values. The multi-degree of freedom design is carried through design, fabrication, and testing. In-duct attenuation predictions compare well with measured data and the multi-degree of freedom liner is shown to outperform a more conventional liner over a range of flow conditions. These promising results provide further confidence in the design tool, as well as the enhancements made to the overall design process.

Nark, Douglas M.↗
NASA NTRS2008

Verifying and Validating Proposed Models for FSW Process Optimization

This slide presentation reviews Friction Stir Welding (FSW) and the attempts to model the process in order to optimize and improve the process. The studies are ongoing to validate and refine the model of metal flow in the FSW process. There are slides showing the conventional FSW process, a couple of weld tool designs and how the design interacts with the metal flow path. The two basic components of the weld tool are shown, along with geometries of the shoulder design. Modeling of the FSW process is reviewed. Other topics include (1) Microstructure features, (2) Flow Streamlines, (3) Steady-state Nature, and (4) Grain Refinement Mechanisms

Schneider, Judith↗
DOE OSTI2024

Data Visualization and Analytics for Optimal Process Parameter Selection in Turning

The objective of this project is to research physics-guided machine learning methods to recommend optimal tools and machining process parameters for turning applications using the MSC test database. For a given turning application, the MSC metalworking specialist needs to make decisions on tools and the associated process parameters for the MSC customer. For a given material, there are many alternatives for tools and a wide range of process parameters to consider. MSC has built a database of tools and parameters for different applications from the historical turning tests completed at various customer sites. The research project aims to use machine learning methods to predict optimal tools and process parameters for the MSC metalworking specialists using the MSC test database. This enables continuous learning of optimal tool and process parameters for different applications as new information is collected from testing. Through MSC, this information can be shared with machining shops across the US leading to improved productivity and efficiency.

42 ENGINEERING↗
NASA NTRS1990

Concurrent micromechanical tailoring and fabrication process optimization for metal-matrix composites

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Morel, M.↗
NASA NTRS1991

Combined micromechanical and fabrication process optimization for metal-matrix composites

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Morel, M.↗
NASA NTRS1983

Optimal processing of satellite-derived magnetic anomaly data

It is shown how the concept of the power spectrum can be extended to two-dimensional spatial power spectra and how it can be used in determining optimal data processing methods for satellite-derived magnetic anomaly data and planning missions to obtain such data. The analysis techniques are applied to the data set and data-processing procedure described by Mayhew et al. (1980), a study that treats magnetic anomaly data for Australia and the surrounding ocean obtained by the polar orbit POGO series satellites. It is shown that the data-processing method used by Mayhew et al. is approximately equivalent to an invariant two-dimensional linear filter and that it is reasonably close to optimal with respect to accuracy, although some possible improvements are suggested. However, as is usual when filtering data, some real 'signal' is unavoidably removed along with the 'noise' resulting in errors that can be quite large. A method for reducing these errors by using additional data from a medium inclination orbit satellite (for example, 60 deg inclination) is proposed.

Mcleod, M. G.↗
NASA NTRS2010

1-G Human Factors for Optimal Processing and Operability of Ground Systems up to CxP GOP PDR

During the mid stages of design development, up to Constellation Program (CxP) Preliminary Design Review (PDR), the requirements for leveraging I-G human factors for optimizing ground processing of Flight Hardware were mature for levels - 2, 3, 4, and 5. This paper gives an overview of the accomplishments achieved during that time. The main focus of this paper will be on the CxP Ground Operations Project human factors engineering analysis process using a Human Factors Engineering Analysis Tool (HFEAT) for developing the level- 5 requirements effecting the design development of the subsystems for Ground Support System (GSS), and Ground Support Equipment (GSE).

Stambolian, Damon B.↗
DOE OSTI2022

A process optimization framework for laser direct energy deposition: Densification, microstructure, and mechanical properties of an Fe-Cr alloy

Laser Direct Energy Deposition (DED) is a metal additive manufacturing technique with the ability to fabricate large and complex parts through deposition of metal powders. However, achieving high-density parts and targeted build heights using DED can be challenging due to the large number of highly sensitive process variables. This work proposes a robust fabrication parameter optimization framework to generate process maps for primary parameters in DED, including laser power, scan speed, mass flow rate, hatch spacing, and layer height. Simple single-track experiments were utilized to map out the parameter space, and a combination of geometric criteria for hatch spacing and layer height were proposed to determine parameter sets that achieve both targeted build heights and mitigate porosity formation. Using this framework, specimens with >99 % density and consistent mechanical properties were successfully fabricated over a wide range of process parameters for an Fe-9wt.%Cr (Fe9Cr) alloy, a surrogate for radiation damage-resistant reduced activation ferritic/martensitic (RAFM) steels. Processing these materials using DED is of particular interest in the development of plasma facing components for nuclear fusion applications. The microstructure and mechanical properties of as-printed Fe9Cr were characterized using optical and electron microscopy, X-ray diffraction, and uniaxial tensile tests. As-printed Fe9Cr displayed ~25 % elongation and ultimate tensile strengths of up to 475 MPa which is comparable to similar wrought alloys. Finally, the proposed framework will allow for accelerated DED parameter optimization for novel alloy systems, as well as open the possibility for local microstructure control while simultaneously mitigating defect formation.

42 ENGINEERING↗