Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Process Development and Demonstration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

JOWOG 22/2 - Actinide Chemical Technology (July 9-13, 2012)

The Plutonium Science and Manufacturing Directorate provides world-class, safe, secure, and reliable special nuclear material research, process development, technology demonstration, and manufacturing capabilities that support the nation's defense, energy, and environmental needs. We safely and efficiently process plutonium, uranium, and other actinide materials to meet national program requirements, while expanding the scientific and engineering basis of nuclear weapons-based manufacturing, and while producing the next generation of nuclear engineers and scientists. Actinide Process Chemistry (NCO-2) safely and efficiently processes plutonium and other actinide compounds to meet the nation's nuclear defense program needs. All of our processing activities are done in a world class and highly regulated nuclear facility. NCO-2's plutonium processing activities consist of direct oxide reduction, metal chlorination, americium extraction, and electrorefining. In addition, NCO-2 uses hydrochloric and nitric acid dissolutions for both plutonium processing and reduction of hazardous components in the waste streams. Finally, NCO-2 is a key team member in the processing of plutonium oxide from disassembled pits and the subsequent stabilization of plutonium oxide for safe and stable long-term storage.

36 MATERIALS SCIENCE↗

INL/EXT-17-41117-Rev000

The mission of the U.S. Department of Energy’s Office of Nuclear Energy (DOE-NE) is to advance nuclear power as a resource that is capable of meeting the nation’s energy, environmental, and national security needs by resolving technical, cost, safety, proliferation resistance, and security barriers through research, development, and demonstration. There has never been a more compelling time to develop sources of safe, clean, renewable, carbon-free base power for the United States. Over six decades of use, nuclear power has been proven to be a safe and reliable base alternative to fossil energy sources. The primary barriers to wider commercialization of nuclear power are the life-cycle costs of current plants, the long cycle associated with development of new nuclear technologies that may be more suitable for today’s energy markets, and the regulatory risk associated with this investment in new nuclear technology. While many innovative nuclear energy concepts exist that match current energy market needs, the lengthy and expensive research, development, and demonstration process and uncertain prospects for licensing discourages investment of private capital. The DOE-NE strategy both sustains the current reactor fleet and provides technology options for development of advanced nuclear energy systems. The strategy for moving innovative ideas to the marketplace centers on the Gateway for Accelerated Innovation in Nuclear (GAIN) Initiative. As the lead national laboratory for DOE-NE, Idaho National Laboratory provides much of the nuclear research, development, and demonstration capability needed to move nuclear innovation forward to deployment.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Materials and Fuels Complex Five-Year Mission Strategy FY19 - FY23

The mission of the U.S. Department of Energy’s Office of Nuclear Energy (DOE-NE) is to advance nuclear power as a resource that is capable of meeting the nation’s energy, environmental, and national security needs by resolving technical, cost, safety, proliferation resistance, and security barriers through research, development, and demonstration (RD&D). There has never been a more compelling time to develop sources of safe, clean, renewable, carbon-free base power for the United States. Over six decades of use, nuclear power has been proven to be a safe and reliable base alternative to fossil energy sources. The primary barriers to wider commercialization of nuclear power are the life-cycle costs of current plants, the long cycle associated with development of new nuclear technologies that may be more suitable for today’s energy markets, including the management and disposition of used nuclear fuel, and the regulatory risk associated with this investment in new nuclear technology. These barriers can be addressed, in good part, by development of new technology that is simpler and therefore simpler to license, and by establishing new technology development approaches that more quickly establish design and safety bases that provide risk-averse investors and regulators the confidence they need for new technology to enter the market. While many innovative nuclear energy concepts exist that match current energy market needs, the lengthy and expensive research, development, and demonstration process and uncertain prospects for licensing discourages investment of private capital.

99 GENERAL AND MISCELLANEOUS↗

Bimetallic Channel Wall Nozzle Development and Hot-Fire Testing Using Additively Manufactured Laser Wire Direct Closeout Technology

NASA has been developing and advancing regeneratively-cooled channel wall nozzle technology for liquid rocket engines to reduce cost and schedules associated with fabrication. One of the primary methods being advanced is Laser Wire Direct Closeout (LWDC). LWDC was developed to provide an additively manufactured laser deposited closeout of the coolant channels that also forms the structural jacket in-situ. This technique has been previously demonstrated through process development and hot-fire testing on a series of subscale nozzles at NASA Marshall Space Flight Center. The hot-fire test articles were fabricated using monolithic alloys to simplify the fabrication process. Ongoing research is being conducted to further expand use of this process for increased scale and bimetallic or multi-alloy options. The use of multi-alloys is desired to fully optimize the combination of materials in the radial and axial directions to reduce overall weight of the nozzle and allow for higher thermal and structural margins on the channel wall nozzle. NASA recently completed process development and hot-fire testing of a series of channel wall nozzles that incorporate a copper-alloy as the hotwall liner material and a superalloy and combination thereof for the structural jacket using the LWDC technique. The fabrication process was further advanced by using a multi-alloy axial joint using explosive bonding integrating a copper-alloy at the forward end of the nozzle hotwall and a stainless-alloy for the remaining length. A third alloy was then used for the channel closeout using the LWDC process. This paper will describe the process development using the LWDC process for channel closeout utilizing the multi-alloys, hardware design and results from hot-fire testing on subscale multi-alloy LWDC channel cooled nozzles.

Gradl, Paul↗

NRIC Gap Assessment

The National Reactor Innovation Center (NRIC) conducted a Gap Assessment to identify the missing national laboratory capabilities needed to enable demonstration of industry reactor concepts. Input was gathered from the NRIC Demonstration Reactor Capabilities Survey (DRCS), experience with the DE-FOA-0002271 “Advanced Reactor Demonstration” proposal development process, and industry-led Technology Working Group (TWG) letters. Thirty-seven reactor concepts from industry were considered in the Gap Assessment and 20 fundamental problems were identified.

42 ENGINEERING↗

Investigation of a “Sharps” Incident

Special nuclear material research, process development, technology demonstration, and manufacturing capabilities are provided at the Los Alamos National Laboratory Plutonium Facility. Engineered barriers provide the most effective protection from radioactive and hazardous materials. The Worker Safety Security Team augments these passive safety feature by investigating incidents to identify appropriate prevention and mitigation measures. “Learning Teams” facilitate employee feedback loop and integration toward process improvement. Here, this article reports an investigation of a “Sharps” incident and reviews a case study of a technician that cuts his left thumb while making a gasket. Causal analysis of the sharps incident uncovered contributing factors that created the environment in which the incident occurred. Finally, latent organizational conditions that created error-likely situations or weakened defenses were identified and controlled. Effective improvements that reduce the probability or consequence of similar sharps incidents were implemented.

61 RADIATION PROTECTION AND DOSIMETRY↗

Energy Saving Glass Lamination via Selective Radio-Frequency Heating

This Inventions and Innovations program supported the technical and commercial research and development needed to elevate Ceralink's energy saving process for flat glass lamination from bench scale to a self-supporting technology with significant potential for growth. Radio-frequency heating was any un-explored option for laminating glass prior to this program. With significant commercial success through time and energy savings in the wood, paper, and plastics industries, RF heating was found to have significant promise for the energy intensive glass lamination industry. A major technical goal of the program was to demonstrate RF lamination across a wide range of laminate sizes and materials. This was successfully accomplished, dispelling many skeptics' concerns about the abilities of the technology. Ceralink laminated panels up to 2 ft x 3 ft, with four sets processed simultaneously, in a 3 minute cycle. All major categories of interlayer materials were found to work with RF lamination. In addition to laminating glass, other materials including photovoltaic silicon solar cells, light emitting diodes, metallized glass, plastics (acrylic and polycarbonate), and ceramics (alumina) were found compatible with the RF process. This opens up a wide range of commercial opportunities beyond the initially targeted automotive industry. The dramatic energy savings reported for RF lamination at the bench scale were found to be maintained through the scale up of the process. Even at 2 ft x 3 ft panel sizes, energy savings are estimated to be at least 90% compared to autoclaving or vacuum lamination. With targeted promotion through conference presentations, press releases and internet presence, RF lamination has gained significant attention, drawing large audiences at American Ceramic Society meetings. The commercialization success of the project includes the establishment of a revenue-generating business model for providing process development and demonstrations for potential RF lamination users. A path to industrial energy benefits and revenue through industrial equipment sales was established in a partnership with Thermex Thermatron, a manufacturer of RF equipment.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

American Made Challenges Battery Voucher Program Cooperative Research and Development Agreement (Cooperative Research and Development Final Report, CRADA Number CRD-21-17533)

Renewance is a Phase II winner of the U.S. Department of Energy Lithium-ion Battery Recycling Prize. The Prize is designed to incentivize American entrepreneurs to develop and demonstrate processes that, when scaled, have the potential to profitably capture 90% of all discarded or spent lithium-based batteries (LIB) in the Unites States for eventual recovery of key materials for re-introductions into the U.S. supply chain. The objective of this work is to enable a more efficient evaluation of battery sources for second life applications prior to ultimately being recycled, through evaluation of chemistry characteristics, projected battery lifetime, and application history. This work will develop the capability to identify groups of batteries that may be useful for second life and reduce the cost of end-of-life (EOL) LIB evaluation and repurposing. To meet the objective, NREL will use existing and new data to create a refined algorithm that could be used to evaluate batches of batteries for potential reuse based on manufacturing date and historical use characteristics. Based on current battery market prices and compiled literature data, a starting-point estimate of the market value of the batteries for reuse based on expected lifetime will be included in the algorithm. With the projected surge in LIB demand, battery second life is a new area ripe for development and investment from companies like Renewance. With so few large format batteries reaching EOL to date, this is a new market with a variety of areas for optimization and adding value. This work with Renewance is an example of how existing expertise in battery degradation at NREL can be used to reduce the cost of shifting a battery into a second life application. With these cost reductions, this work is also facilitating the development of a battery circular economy in the United States. A robust circular economy can maximize the utilization of critical metals demanded by battery technology such as nickel and cobalt while also reducing the costs of batteries in the marketplace for the many end-uses needed for the green energy transition. The supply of these metals is limited, and we face a supply chain shortage both domestically and globally unless we can ensure they are being used to their maximum potential. This research can improve the economics of a battery circular economy to make it a more likely path for EOL batteries with critical metals. CRADA benefit to DOE, Participant, and US Taxpayer: assists laboratory in achieving programmatic scope competencies, uses the laboratory's core competencies.

25 ENERGY STORAGE↗

Measurement of Spray Chamber Ignition Delay and Cetane Numbers for Aviation Turbine Fuels

Experiments using pure compounds, National Jet Fuels Combustion Program (NJFCP) test fuels, and commercial jet fuels were conducted to demonstrate the equivalence of the indicated cetane number (ICN) and derived cetane number (DCN) for jet fuels. The calibrated range for ICN was also extended to lower cetane number (CN) values (5 to 35) to allow CN quantification for jet fuel synthetic blending components (SBCs) with low CN. ICN and DCN were shown to be highly correlated for values above about 30. This study presents the most comprehensive comparison of these two methods published to date. Because of the importance of low-volume test methods for early-stage SBC production process development, we demonstrated that ICN and DCN can be accurately measured with 15 mL of fuel, well below 40 to 100 mL required by standard methods. ICN or DCN is important for jet fuels because fuels with lower CN are more prone to lean blowout (LBO), an undesirable operational failure in a jet engine. Comparing data on a fuel-to-air ratio (Φ) at LBO for the NJFCP fuels shows similar linear correlations for ICN and DCN. Ignition delay measurements at lower-pressure and higher-temperature conditions may be more directly relevant to LBO. At 675 °C, 0.5 MPa, and a global Φ of roughly 0.68, ignition delay time correlations to LBO were similar to those produced from DCN and ICN. A much weaker correlation was obtained with a global Φ value of 0.34.

09 BIOMASS FUELS↗

Technician's Perspective on an Ever-Changing Research Environment: Catalytic Conversion of Biomass to Fuels

The biomass thermochemical conversion platform at the National Renewable Energy Laboratory (NREL) develops and demonstrates processes for the conversion of biomass to fuels and chemicals including gasification, pyrolysis, syngas clean-up, and catalytic synthesis of alcohol and hydrocarbon fuels. In this talk, I will discuss the challenges of being a technician in this type of research environment, including handling and working with catalytic materials and hazardous chemicals, building systems without being given all of the necessary specifications, pushing the limits of the systems through ever-changing experiments, and achieving two-way communication with engineers and supervisors. I will do this by way of two examples from recent research. First, I will describe a unique operate-to-failure experiment in the gasification of chicken litter that resulted in the formation of a solid plug in the gasifier, requiring several technicians to chisel the material out. Second, I will compare and contrast bench scale and pilot scale catalyst research, including instances where both are conducted simultaneously from common upstream equipment. By way of example, I hope to illustrate the importance of researchers 1) understanding the technicians' perspective on tasks, 2) openly communicating among all team members, and 3) knowing when to voice opinions. I believe the examples in this talk will highlight the crucial role of a technical staff: skills attained by years of experience to build and operate research and production systems. The talk will also showcase the responsibilities of NREL technicians and highlight some interesting behind-the-scenes work that makes data generation from NREL's thermochemical process development unit possible.

09 BIOMASS FUELS↗

Investigation of the synthesis and characterization of platinum-DMSA nanoparticles using millifluidic chip reactor

Here a continuous flow process for production of water-soluble Platinum-Dimercaptosuccinic acid (Pt(DMSA)) nanoparticles at ambient conditions using millifluidics is demonstrated. The process development was supported by in-situ synchrotron radiation-based X-ray absorption spectroscopy (XAS) investigations. The XAS revealed that the nucleation and growth of the Pt(DMSA) nanoparticles is extremely fast. Such a fast nucleation and growth process was also found to hinder coating of the channel walls, except at the zone 1 where the reactants first interact. The engineering of hitherto unreported Pt(DMSA) nanoparticles, well characterized using High-resolution transmission electron microscopy (HR-TEM), Scanning transmission electron microscopy (STEM), Scanning electron microscopy (SEM), Energy dispersive spectroscopy (EDS), Powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infra-red spectroscopy (FT-IR), using continuous flow processes offers potential opportunities for scale-up.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigation of injury/illness data at a nuclear facility. Part II

At Los Alamos National Laboratory (LANL), there are several nuclear facilities, accelerator facilities, radiological facilities, explosives sites, moderate- and high-hazard non-nuclear facilities, biosciences laboratory, etc. The Plutonium Science and Manufacturing Directorate (ADPSM) provides special nuclear material research, process development, technology demonstration, and manufacturing capabilities. ADPSM manages the LANL Plutonium Facility. Within the Radiological Control Area at TA-55 (PF-4), chemical and metallurgical operations with plutonium and other hazardous materials are performed. LANL Health and Safety Programs investigate injury and illness data. In this study, statistically significant trends have been identified and compared for LANL, ADPSM, and PF-4 injury/illness cases. A previously described output metric is used to measures LANL management progress towards meeting its operational safety objectives and goals. Timelines are used to determine trends in Injury/Illness types. Pareto Charts are used to prioritize causal factors. The data generated from analysis of Injury/Illness data have helped identify and reduce the number of corresponding causal factors.

97 MATHEMATICS AND COMPUTING↗

Desalination of brines produced from the geologic storage of carbon dioxide

Geologic carbon dioxide sequestration (GCS) will play a crucial role in limiting anthropogenic greenhouse gas emissions. GCS is the practice of capturing carbon dioxide (CO 2 ) from industrial sources and storing it in subsurface geologic formations, such as saline formations. These saline formations are typified by a porous interconnected rock strata, saturated with saline brine at a depth of >800 m. Because of the large volumes available, storage of CO 2 into deep saline formations with caprock seals and far from exiting faults will be key for long term reductions of anthropogenic CO 2 emissions. The high pressure injection of CO 2 into the subsurface can cause an increase in subsurface pressure. Open and highly porous formations can have CO 2 injected without causing a significant rise in formation pressure; however, closed or low porosity formations are more sensitive to the subsurface injection of CO 2 with regard to subsurface pressure. Such formations would ideally be located near existing fossil fuel power plants or other industrial emitters of CO 2 who would require GCS. In order to reduce the risk of induced seismic activity near minor fault structures, formation pressure management is needed. This will require the extraction of brines from the formation and these brines could be extracted prior to or during GCS. This extraction will maintain or reduce the subsurface pressure and enhance CO 2 storage capacity. The extracted brine can be dewatered/desalinated, becoming both a source of usable water and a concentrated brine which could be either reinjected into a nearby formation, crystallized, or discharged into an evaporation pond. The Department of Energy Office of Fossil Energy’s commitment to studying formation pressure management in GCS has been demonstrated with the recent awarding of $30,000,000 for two Brine Extraction Storage Test (BEST) projects, whose main goal is to develop and validate strategies for managing formation pressure through brine (Martin 2016). A secondary goal of these projects is to develop and demonstrate processes to extract usable water from these high salinity produced brines.

54 ENVIRONMENTAL SCIENCES↗

Energy pulse bonding

To eliminate many of the present termination problems a technique called energy pulse bonding (EPB) was developed. The process demonstrated the capability of: (1) joining conductors without prior removal of insulations, (2) joining conductors without danger of brittle intermetallics, (3) increased joint temperature capability, (4) simultaneous formation of several bonds, (5) capability of higher joint density, and (6) a production oriented process. The following metals were successfully bonded in the solid state: copper, beryllium copper, phosphor bronze, aluminum, brass, and Kovar.

Smith, G. C.↗

STATUS OF SRF FACILITIES AT SNS

The Spallation Neutron Source (SNS) has recognized the need for developing in-house capability to ensure long term sustainability of the superconducting linac (SCL). SNS has made substantial gains in the last 6 years in understanding SCL operation, including system and equipment limiting factors, and resolution of system and equipment issues. Significant effort and focus is required to assure on-going success in the operation, maintenance, and improvement of the SCL and to address the requirements of the upgrade project for the Second Target Station. These interdependent efforts include implementation of demonstrated improvements, fabrication of spare cryomodules, cavity R&D to enhance machine performance, and related SRF facility developments. Cryomodule and vertical cavity testing facilities are being developed to demonstrate process capabilities and to further understand the collective limitations of installed cavities. The status and future plans for SRF facilities at SNS will be presented.

Kim, Sang-Ho↗

Combustion Synthesis of Transuranic-doped Ceramics for Nuclear Waste Immobilization

Utilizing the devised SCS technique, crystalline transuranic-doped zirconate pyrochlores were formed for the first time without the need for a subsequent heating step. Typically, materials rapidly synthesized in a single-step self-sustaining exothermic reaction require further heating to induce crystallization and purify the product. The need for this secondary processing step can be attributed to factors such as an improper oxidizer to fuel ratio and the utilization of strong complexing compounds as fuels (i.e., reducing agents), all of which hinder complete combustion. The efficacy of the developed process was demonstrated by fabricating crystalline plutonium-doped Gd2Zr2O7 from solutions containing metal nitrates and urea in a properly tuned ratio

Burton-Allen, Janiya D.↗

Having a Come-Apart: Lessons Learned from Additively Manufactured Hardware Failures

NASA has been engaged with additively manufactured (AM) process and component development since the 2000’s. AM offers various technical advantages, such as enhanced hardware design complexity, part consolidation, and processing of novel alloys in addition to programmatic advantages for reduction in processing time and cost. The focus of much of the AM development at NASA has been to mature the various processes, characterize material properties, develop standards, produce demonstrator parts, and integrate AM hardware in liquid rocket engines. These aspects have been demonstrated through process and design iterations using a methodical characterization, test-fail-fix cycles, as well as application and dissemination of lessons learned. In addition to these fundamental demonstrations of the AM process and hardware development, alloys that provide performance advantages in the high temperature and high-pressure environments have been matured for use in rocket engines. These environments are challenging for any alloy and any design, and the AM process is required to fully meet the intended design requirements. The importance of proper AM process was made evident in the failure of a Laser Powder Bed Fusion (L-PBF) copper-alloy combustion chamber during a hot-fire test due to a degraded material quality resulted from an AM process issue. The hot-fire test aimed to demonstrate high duty cycle under a risk-tolerant development project, where consequences of component failure would be minimal. However, the unintentional component failure emphasized the necessity of robust material characterization and rigorous process control procedures for the safe use of AM components in critical applications. In part, such concerns motivate the AM certification approach that NASA has recently adopted in NASA-STD-6030 “Additive Manufacturing Requirements for Spaceflight Systems”. This presentation provides an overview of the previously mentioned failure, a discussion on the evaluation of the failed chamber and supplemental chambers produced at the same time, a representative material samples that included intentional build witness lines, and a summary of the key results and recommendations from the evaluations. NASA continues to approach AM processes and designs with a level of risk and acceptance of failures that is appropriate for the project objectives, with the overall goal of safe implementation of AM technology and transferring AM technology into commercial space applications. The objective of this presentation is to provide awareness to the community working critical and non-critical AM components and the lessons learned on proper implementation of AM.

Additive Manufacturing↗

Vehicle Modeling for use in the CAFE model: Process description and modeling assumptions

The objective of this project is to develop and demonstrate a process that, at a minimum, provides more robust information that can be used to calibrate inputs applicable under the CAFE model’s existing structure. The project will be more fully successful if a process can be developed that minimizes the need for decision trees and replaces the synergy factors by inputs provided directly from a vehicle simulation tool. The report provides a description of the process that was developed by Argonne National Laboratory and implemented in Autonomie.

33 ADVANCED PROPULSION SYSTEMS↗