Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Powder Bed Additive Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Investigation into the Use of the Concept Laser QM System as an In-Situ Research and Evaluation Tool

The NASA Marshall Space Flight Center (MSFC) is using a Concept Laser Fusing (Cusing) M2 powder bed additive manufacturing system for the build of space flight prototypes and hardware. NASA MSFC is collecting and analyzing data from the M2 QM Meltpool and QM Coating systems for builds. This data is intended to aide in understanding of the powder-bed additive manufacturing process, and in the development of a thermal model for the process. The QM systems are marketed by Concept Laser GmbH as in-situ quality management modules. The QM Meltpool system uses both a high-speed near-IR camera and a photodiode to monitor the melt pool generated by the laser. The software determines from the camera images the size of the melt pool. The camera also measures the integrated intensity of the IR radiation, and the photodiode gives an intensity value based on the brightness of the melt pool. The QM coating system uses a high resolution optical camera to image the surface after each layer has been formed. The objective of this investigation was to determine the adequacy of the QM Meltpool system as a research instrument for in-situ measurement of melt pool size and temperature and its applicability to NASA's objectives in (1) Developing a process thermal model and (2) Quantifying feedback measurements with the intent of meeting quality requirements or specifications. Note that Concept Laser markets the system only as capable of giving an indication of changes between builds, not as an in-situ research and evaluation tool. A secondary objective of the investigation is to determine the adequacy of the QM Coating system as an in-situ layer-wise geometry and layer quality evaluation tool.

Bagg, Stacey↗
NASA NTRSDate not supplied

Assessment of Segmentation-Induced Deviations of Porosity Metrics in Powder Bed Fusion Additively Manufactured Components

Post processing X-ray computational tomography (CT) inspection data for additively manufactured (AM) components can induce deviations in defect quantification, affecting subsequent fatigue and failure predictions. To assess the influence and potential impact of segmentation-induced measurement deviations, this paper applies several segmentation techniques to X-ray CT data for powder bed fusion Ti-6Al-4V specimens exhibiting porosity conditions. X-ray CT reconstructions were segmented with varying techniques including Otsu’s thresholding, random forest, k-nearest neighbors, and the multilayer perceptron. Metrics such as pore size and global porosity were compared for internal validity. Then, top-down X-ray CT measurements of surface-breaking porosity were compared to optical profilometry for cross-validation.

Data fusion↗
NASA NTRSDate not supplied

Uncertainty Quantification and Sensitivity Analysis in Process-Structure-Property Simulations for Laser Powder Bed Fusion Additive Manufacturing

Process variations and process-induced defects like porosity cause significant uncertainty in the microstructure and mechanical behavior of additively manufactured metals. Establishing process-structure-property (PSP) relationships and quantifying uncertainty using experiments alone is costly, especially for structural applications where mechanical allowables must be established for qualification and certification. This work presents a PSP simulation framework for laser powder bed fusion with a focus on uncertainty quantification through probabilistic calibration and multi-fidelity uncertainty propagation. Motivated by phenomenological input parameters related to grain nucleation and growth that are difficult to characterize, a global sensitivity analysis (GSA) is completed. Through GSA, the most important input parameters are identified based on their influence on the statistical distributions of microstructural metrics that influence mechanical behavior, including grain size, morphology, and crystallographic texture. The results provide insight on what experiments are necessary to quantify and control PSP uncertainties, particularly those associated with the more challenging input parameters.

additive manufacturing↗
NASA NTRS2017

Systems and Methods for Designing and Fabricating Contact-Free Support Structures for Overhang Geometries of Parts in Powder-Bed Metal Additive Manufacturing

Systems and methods are provided for designing and fabricating contact-free support structures for overhang geometries of parts fabricated using electron beam additive manufacturing. One or more layers of un-melted metallic powder are disposed in an elongate gap between an upper horizontal surface of the support structure and a lower surface of the overhang geometry. The powder conducts heat from the overhang geometry to the support structure. The support structure acts as a heat sink to enhance heat transfer and reduce the temperature and severe thermal gradients due to poor thermal conductivity of metallic powders underneath the overhang. Because the support structure is not connected to the part, the support structure can be removed freely without any post-processing step.

Chou, Yuag-Shan↗
NASA NTRS2017

Relationship of Powder Feedstock Variability to Microstructure and Defects in Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer by layer. For selective laser melted (SLM) Alloy 718, the powders that are available off-the-shelf are in the 10-45 or 15-45 micron size range. A comprehensive investigation of sixteen powders from these typical ranges and two off-nominal-sized powders is underway to gain insight into the impact of feedstock on processing, durability and performance of 718 SLM space-flight hardware. This talk emphasizes an aspect of this work: the impact of powder variability on the microstructure and defects observed in the as-fabricated and full heated material, where lab-scale components were built using vendor recommended parameters. These typical powders exhibit variation in composition, percentage of fines, roughness, morphology and particle size distribution. How these differences relate to the melt-pool size, porosity, grain structure, precipitate distributions, and inclusion content will be presented and discussed in context of build quality and powder acceptance.

Characterization↗
NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗
NASA NTRSDate not supplied

Correlations Between Porosity, Spatter, and Process Metrics for Powder Bed Fusion Laser Beam Metallic Additive Manufacturing

Components fabricated using the powder bed fusion laser beam metallic (PBF-LB/M)additive manufacturing process are the result of a multitude of weld passes conducted sequentially. Qualifying components for aerospace applications requires a thorough understanding of the process-structure-properties relationships. Porosity defects are known to have a strong adverse effect on the mechanical properties of a component. In particular, porosity defects created by lack of fusion have high aspect ratio morphologies leading to stress concentrations that become crack initiation sites. In the present work, the occurrence of spatter induced lack of fusion porosity was studied using synchronized in-situ process monitoring, additive manufacturing model-based process metrics, and high-resolution X-ray computed tomography. The results show that lack of fusion porosity is statistically correlated with unremoved welding spatter ejecta of the PBF-LB/M process and process metrics related to the hatching strategy.

Qualification↗
NASA NTRS2018

Characterizing Performance of Additively Manufacturing Regenerative Cooled Combustion Chambers Through Hot Fire Testing

NASA Marshall Space Flight Center (MSFC) has developed several additive manufactured regenerative cooled combustion chambers from 2014 to present. Chambers have been constructed using the Selective Laser Melting (SLM) powder bed additive manufacturing (AM) technique. The materials used for the chambers has varied from Inconel 718, Inconel 625, GRCop-84, and C18150 metal alloys. The surface finish and build techniques used to successfully manufacture combustion chambers using the SLM AM result in as built surface finish and off nominal geometric features. This paper discusses and reviews the effects of surface roughness, flow area, and hydraulic performance of regenerative cooled combustion chambers. The thrust chambers designs tested ranged from 200 to 1,400 psia producing 1,000 to 35,000 lbf thrust. Empirical data from four test campaigns will be reviewed and related to design modeling parameters such as pressure drop, surface roughness, and actual fluid flow geometry. Correlation results with simple 2-D CFD modeling will also be presented. The goal of the work is to better understand how the finished additive manufactured component characteristics inside internal features can effect regenerative cooling chamber design. Adjustments to design methodology will be discussed and recommended based on the above results.

Garcia, C. P.↗
NASA NTRS2014

Fabrication of Turbine Disk Materials by Additive Manufacturing

Precipitation-strengthened, nickel-based superalloys are widely used in the aerospace and energy industries due to their excellent environmental resistance and outstanding mechanical properties under extreme conditions. Powder-bed additive manufacturing (AM) technologies offer the potential to revolutionize the processing of superalloy turbine components by eliminating the need for extensive inventory or expensive legacy tooling. Like selective laser melting (SLM), electron beam melting (EBM) constructs three-dimensional dense components layer-by-layer by melting and solidification of atomized, pre-alloyed powder feedstock within 50-200 micron layers. While SLM has been more widely used for AM of nickel alloys like 718, EBM offers several distinct advantages, such as less retained residual stress, lower risk of contamination, and faster build rates with multiple-electron-beam configurations. These advantages are particularly attractive for turbine disks, for which excessive residual stress and contamination can shorten disk life during high-temperature operation. In this presentation, we will discuss the feasibility of fabricating disk superalloy components using EBM AM. Originally developed using powder metallurgy forging processing, disk superalloys contain a higher refractory content and precipitate volume fraction than alloy 718, thus making them more prone to thermal cracking during AM. This and other challenges to produce homogeneous builds with desired properties will be presented. In particular, the quality of lab-scale samples fabricated via a design of experiments, in which the beam current, build temperature, and beam velocity were varied, will be summarized. The relationship between processing parameters, microstructure, grain orientation, and mechanical response will be discussed.

oxidation↗
NASA NTRS2019

Optimization of Aluminum-Tin Ink Composition and Sintering in Atmospheric Conditions

This study will focus on the basics of generating an aluminum-tin ink that can sinter in air and exhibits properties near that of a solid aluminum-tin alloy. Sintering temperatures will also be assessed in this study. Once the optimal aluminum ink composition is determined, the optimal ink thickness for homogeneous sintering must be determined by additional experimentation. Additive manufacturing is a rapidly developing and growing manufacturing process and has proven successful in many different ways. Processes, such as extrusion three-dimensional (3D) printing and selective laser melting (SLM), have proven to work but have limitations, such as material capabilities or density issues. SLM is a revolutionary process for additive manufacturing of metals but cannot be used in outer space due to the need for metallic powder which would diffuse into the atmosphere in a zero-gravity environment. For this reason, metallic ink additive manufacturing is a potential solution. Work is being done on metallic ink additive manufacturing in a vacuum for electrical applications. This project has focused on developing an aluminum-tin metallic ink that can sinter without the need of a vacuum or inert gas-purged atmosphere in order to prevent oxidation of the aluminum by adding flux. Once a potential ink composition has been determined through sintering of small disks and thin layers of ink, the ink may be studied with a multimaterial 3D printer at NASA Marshall Space Flight Center (MSFC) in future experiments. If successful, this aluminum-tin ink will be capable for use on the International Space Station to make replacement parts quickly. Along with its zero-gravity advantages, this ink may also have applications on Earth because it may be extruded on a substrate with precise ceramic tips in a 3D printing process. This would allow the fabrication of precise, complex shapes and may generate a much faster and more efficient printing process as compared with traditional powder bed additive manufacturing processes. The process would not be limited by a small building volume because the system would not require an enclosed chamber.

Courtright, Z. S.↗