Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pore volume”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Laboratory Evaluation to Increase Effectiveness of Field-Scale Soil Flushing in the Hanford 100 Areas

This laboratory study was initiated to develop an improved technical understanding of the key controlling geochemical and physical processes of mobilizing residual Cr(VI) in Hanford sediments to provide increased effectiveness in soil flushing activities planned for Hanford 100 Areas. This was accomplished by (1) quantifying Cr mass, release rate, and surface phase changes as Cr is leached from different Hanford sediments; (2) maximizing Cr leaching during soil flushing by evaluating different leach solutions and leach strategies; and (3) minimizing leaching of remaining residual Cr after soil flushing ends. To quantify geochemical controls on Cr leaching from sediments, sequential liquid extractions were used to identify aqueous, adsorbed, and solid Cr surface phases (precipitates or Cr incorporated into other phases) before and after water-saturated and unsaturated leach experiments with pH 8 artificial groundwater and with other amendment solutions. Changes in the Cr release rate from sediments were also correlated to changes in Cr surface phases. During unsaturated infiltration, water advection occurs primarily through larger pores, with less movement through smaller grain layers leading to a slower release of Cr trapped in smaller pores next to smaller grains. To quantify these physical controls on Cr leaching from sediments, 10 ft high 1-D infiltration experiments were conducted at differing leach solution application rates, and Cr leaching during application and subsequent residual water flow was quantified. Qualitative 2-D experiments were also conducted to evaluate surfactant addition to increase flow in low-permeability zones. Cr-contaminated Hanford sediments from the 100-H, 100-K, 100-D, and 200 East Areas exhibited a wide variety of leach behavior from rapid release of a small amount of Cr to fast (i.e., minutes) and slow (i.e., hours or more) release of high Cr. Sediments with low labile Cr (< 0.2 µg/g) exhibited fast Cr release but less overall release, and most (>95%) leached from the sediments within a few pore volumes in water-saturated columns. With nearly no sorption of chromate, aqueous and sorbed Cr (as chromate) were released quickly from sediment within the first few pore volumes, resulting in high leach concentrations, fast initial Cr release rates, and changes in pre- and post-leach extractions. In contrast, sediments with high labile Cr (0.2 to 20 µg/g) exhibited a combination of fast and slow Cr release due to multiple Cr surface phases contributing to Cr release from the sediment at different rates with greater overall release. This resulted in elevated Cr effluent concentrations even after dozens of pore volumes were leached. In addition, the Cr release rate decreased with increasing time during leaching. A decrease in labile Cr (aqueous Cr, adsorbed Cr, pH 5 acetate dissolved precipitates) in post-leach extractions compared to pre-leach extractions showed initial aqueous and adsorbed Cr release, followed by dissolution of high-solubility precipitates such as CaCrO 4 (if present), then slow dissolution of calcite that may contain some chromate and possibly BaCrO 4 . The labile Cr in all sediments correlated well with the Cr release rate (r 2 = 0.81). Labile Cr also correlated well with the leached mass in water-saturated columns (r 2 = 0.98), and therefore can be used for prediction of potential removal with flushing applications.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

The evolution of coal porosity during pyrolysis

Gasification of coal, municipal waste, or other organic materials is a potential hydrogen source that entails complex thermal decomposition and transport processes. This study provides a multiscale analysis of these processes for sub-bituminous (Usibelli, Healy, Alaska) and lignite (Center, North Dakota) coals and provides data useful for process design. The chemistry, mineralogy, and pore structures of pyrolyzed coal and their evolution with thermal decomposition are discussed. Samples pyrolyzed at 200–1000 °C were analyzed by small-angle neutron scattering; ultra-small, small-, and wide-angle X-ray scattering; and other complementary techniques. Scanning electron microscopy showed new pores in the high-temperature-pyrolyzed material. Upon heating, the coals became progressively denser, and the concentration of hydrogen decreased. Changes in pore volume fell into three temperature ranges: an initial, low-temperature range that, for the Usibelli coal, involved an increase in overall porosity; a mid-temperature range associated with pore volume loss; and a high-temperature range associated with significant porosity increase and char formation. This transformation was paralleled by changes in fractal dimension and correlation length. The higher the pyrolysis temperature the greater the small-pore-volume fraction and overall surface area became. Pyrolysis increased the lateral size of coal crystallites, decreased the amorphous fraction, and increased the aromatics fraction and overall coal rank. Comparisons of neutron and X-ray scattering data and subsequent water uptake studies showed that pre-dried coals can re-hydrate relatively rapidly upon exposure to air, which can significantly affect the porosity calculated from small-angle-scattering data. Fits to the cumulative porosity curves provide a method for modeling the physical and chemical transformation of hydrogen-containing feedstock during gasification.

Anovitz, Lawrence {Larry} [ORNL] (ORCID:0000000226↗
NASA NTRS1984

Long life nickel electrodes for a nickel-hydrogen cell. III - Results of an accelerated test and failure analyses

Nineteen different designs of nickel electrodes were tested in Ni/H2 boiler plate cells in an accelerated low earth orbit cycle regime to the end of their life. The failure analyses of these cells showed that the major performance changes due to the cycling was a severe reduction of their high rate discharge capability rather than an absolute capacity reduction. Many physical changes of the nickel electrodes were observed after the cycling test. These changes include dimensional expansion, sinter rupture, loose black powdering of the active material, morphology changes, active material migration, increase of pore volume, change of pore distribution, and increase of surface area. All of these were caused by active material expansion with cycling. Among these changes, the morphology change which involves migration of active material away from the current collecting nickel sinter appears to be that most responsible for the reduction of the rate capability.

Lim, H. S.↗
DOE OSTI2026

Site specific porosity-thermal performance correlations in neutron irradiated U-10Zr fuel

In this work, we present a site-specific three-dimensional analysis of porosity evolution in neutron-irradiated U–10Zr metallic fuel using high-resolution synchrotron X-ray tomography. Focused ion beam cubic lift-outs from four radial positions—fuel center, middle, edge, and fuel-cladding interaction (FCCI) zones—were imaged, reconstructed, and segmented to quantify pore volume, density, morphology, and pore connectivity. Porosity increased modestly from 5.5% at the center to 10.5% at the edge, yet pore number density increased by over two orders of magnitude in the fuel portion near the FCCI interface (from 4.8 x 10 4 to 6.0 x 10 6 pores/mm 3 ). Morphological classification revealed a progression from small spherical pores at the center to equiaxed and tortuous networks at the periphery, with enhanced orientation along the radial direction. Connectivity and permeability analysis reveal that the FCCI region maintains dense, highly interconnected pores despite a moderate volume fraction, enabling rapid fission gas transport and lanthanide migration. Effective thermal conductivity models incorporating sodium logging confirm that these site-specific pore features critically influenced heat transport during reactor irradiation. These findings demonstrate that pore topology—not just porosity fraction—controls thermal performance and thermal pathways in U–10Zr fuels, impacting fuel thermal performance in a reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2021

Optimizing Surfactant Templating of Yttria-Stabilized Zirconia Aerogels for High-Temperature Applications: Effect of Cationic Surfactant

Aerogels can be used in spaceflight applications as thermal insulators due to their low density, low thermal conductivity, and tortuous path for solid conduction. However, the aerogel formulation must be optimized to increase the thermal stability of the aerogels, as a drastic densification and decrease in surface area often is exhibited after high-temperature exposure. This work considers yttria-stabilized zirconia (YSZ) aerogels, whichhave low thermal conductivity and are expected to be used for temperatures between 600°C and 1000°C. It is anticipated that new sol-gel chemistries will yield YSZ aerogels that exhibit retained mesoporous structure, increased surface area, and minimized shrinkage upon exposure to higher temperatures in the expected use range. This work investigates the addition of surfactant to 20 mol% YSZ aerogels. The cationic surfactant, cetrimonium bromide (CTAB), was used as the templating agent, preventing the collapse of the mesoporous structure upon gelation and drying. It was determined that adding one-half times the critical micelle concentration of CTAB increased the surface area of the aerogels by 72% and 41% and increased the pore volume following exposure to 600°C and1000°C, respectively. This level of CTAB had the greatest increase in surface area and pore volume as compared to aerogels without CTAB or with twice the critical micelle concentration of CTAB. By optimizing the concentration of CTAB, the thermal stability ofYSZ aerogels can be enhanced to make these materials more efficient when used as thermal management systems.

Yttria-stabilized zirconia aerogel↗
DOE OSTI2021

SEM petrography of dispersed organic matter in black shales: A review

Organic matter (OM)-hosted pores are important constituents of the pore system of black shales and play a crucial role in determining their methane adsorption capacity and porosity. OM-hosted pores are generally observed and described with scanning electron microscope (SEM) on Ar ion-milled surfaces. However, SEM imaging is not able to reliably distinguish OM types and relate the observed pores to specific macerals. Partly because of this inability to relate organic pores to macerals, the evolution of organic porosity during thermal maturation remains poorly understood. In this paper, we review the petrographic characteristics of dispersed organic matter (DOM) in black shales under the SEM. Organic petrographic classification of DOM developed for reflected-light microscopy is so far the most practical method when describing DOM in black shales under the SEM because this classification has information on the origin of DOM. Therefore, correlative microscopy (combination of reflected-light and electron microscopy) is the most effective method to identify both OM types and OM-hosted pores. This method, however, is not readily available to most researchers. Although identifying OM on the basis of SEM observations is a challenging task, it is achievable provided there is a good understanding of the studied shales, especially their thermal maturity and original OM composition. Therefore, the overall objective of this paper is to review petrographic characteristics of DOM in black shales under the SEM to provide some guidelines for identifying DOM from SEM observations. We also review factors that control the formation and preservation of OM-hosted pores. OM-hosted pores consist of primary and secondary organic pores. Primary organic pores are pores inherited from the biological structure of the original OM. Secondary organic pores develop during hydrocarbon generation and expulsion from oil-prone OM and are hosted by solid bitumen or pyrobitumen. The development of secondary organic pores is controlled by thermal maturity and OM type, and their preservation is subject to thermal maturity, OM content, and mineralogical composition. The presented view of the evolution of micropore and mesopore characteristics of OM with thermal maturity is based on data from the literature. The specific surface area and pore volume of OM in black shales follow a parabolic pattern with increasing thermal maturity (quantified via vitrinite reflectance, R o ). The initial increase reflects development of OM-hosted pores, and the subsequent decrease is due to denser stacking of aromatic units in the macromolecular structure of OM, with maximum values (specific surface area ~ 300 m 2 /g and pore volume ~ 0.3 cm 3 /g) reached at R o values in the 2.5-3.5% range. The contribution of OM-hosted pores to the pore characteristics of black shales depends on OM content, OM type, and thermal maturity.

03 NATURAL GAS↗
NASA NTRS2023

Optimizing Surfactant Templating of Yttria-Stabilized Zirconia Aerogels for High-Temperature Applications: Effect of Anionic and Nonionic Surfactant

Aerogels, mesoporous materials with extreme material properties including high specific surface area, low density, and low thermal conductivity, can be useful for applications including catalysis, sorption media, and drug delivery. The low thermal conductivity and high surface area of aerogels makes them advantageous as thermal management systems, specifically for aerospace or aeronautics applications. However, the pore collapse and subsequent surface area decrease of aerogels following exposure to high temperatures must be mitigated to allow aerogels to be effectively used in thermal management applications. This work investigates the anionic surfactant sodium dodecyl sulfate (SDS) and the nonionic surfactant Pluronic® P-123 as surfactant templates in yttria-stabilized zirconia (YSZ) aerogels. By utilizing surfactant templates, known to influence pore structure, it is anticipated that sintering and densification of the aerogels following high-temperature exposure will be mitigated. It was determined that the addition of SDS and P-123 increased the surface area and pore volume of as-dried aerogels and suppressed crystallite growth at high temperatures. However, the impact of surfactant templates on the surface area and pore volume of heat-treated aerogels was negligible, potentially due to low concentrations of surfactant and the removal of the surfactant following high-temperature exposure.

Yttria-stabilized zirconia aerogels↗
DOE OSTI2025

Analysis of Degradation and Electrochemical Behavior of Lithium–Oxygen Batteries under Lean Electrolyte Conditions

Lithium-oxygen batteries have garnered much attention in the past decades due to their high energy density and active material abundancy. Decreasing the electrolyte volume is critical to achieving a high energy density for practical applications. Recent works have demonstrated a serious performance limitation at lower electrolyte fillings. Here, in this work, we study specifically the difference between flooded and lean electrolyte lithium-oxygen batteries by systematically tracing the source of performance degradation. We find that the key contributor to the decrease in performance under lean electrolyte conditions stems from the lithium metal anode rather than the cathode. Solid electrolyte interphase (SEI) compositionally appears to be the same from X-ray photoelectron spectroscopy but the coverage is less uniform, and impedance is much higher under lean electrolyte conditions. Such an effect likely produced the observed poorer cycle performance at 10 μL cm -2 (similar to 28% cathode's pore volume filled) vs 100 μL cm -2 (278% of cathode's pore volume) at a capacity of 1.0 mAh cm -2 (0.1 mAh cm -2 ) using an electrolyte composition of 1 M LiTFSI in TEGDME.

Córdoba, Daniel [Argonne National Laboratory (ANL)↗
DOE OSTI2022

HyMARC Seedling: Optimized Hydrogen Adsorbents via Machine Learning and Crystal Engineering

This final report is presented in two parts: In Part 1, the H 2 capacities of a diverse set of 918,734 metal-organic frameworks (MOFs) sourced from 19 databases is predicted via machine learning (ML). Using only 7 structural features as input, ML identifies 8,282 MOFs with the potential to exceed the capacities of state-of-the-art materials. The identified MOFs are predominantly hypothetical compounds having low densities (<0.31 g/cm3) in combination with high surface areas (>5,300 m2/g), void fractions ($0.90), and pore volumes (>3.3 cm3/g). The relative importance of the input features are characterized, and dependencies on the ML algorithm and training set size are quantified. The most important features for predicting H 2 uptake are pore volume (for gravimetric capacity) and void fraction (for volumetric capacity). The ML models are available on the web, allowing for rapid and accurate predictions of the hydrogen capacities of MOFs from limited structural data; the simplest models require only a single crystallographic feature. In part 2, ways to improve the poor powder packing density of MOFs is discussed. More specifically, a strategy that improves packing efficiency and volumetric hydrogen gas storage density dramatically through engineered morphologies and controlled-crystal size distributions is presented that holds promise for maximizing storage capacity for a given MOF. The packing density improvement, demonstrated for the benchmark sorbent MOF-5, leads to a significant enhancement of volumetric hydrogen storage performance relative to commercial MOF-5. System model projections demonstrate that engineering of crystal morphology/size or use of a bimodal distribution of cubic crystal sizes in tandem with system optimization can surpass the 25 g/L volumetric capacity of a typical 700 bar compressed storage system and exceed the DOE targets 2020 volumetric capacity (30 g/L). Finally, a critical link between improved powder packing density and reduced damage upon compaction is revealed leading to sorbents with both high surface area and high density.

08 HYDROGEN↗
DOE OSTI2021

Surviving Under Pressure: The Role of Solvent, Crystal Size, and Morphology During Pelletization of Metal–Organic Frameworks

As metal–organic frameworks (MOFs) gain traction for applications, such as hydrogen storage, it is essential to form the as-synthesized powder materials into shaped bodies with high packing densities to maximize their volumetric performance. Mechanical compaction, which involves compressing the materials at high pressure, has been reported to yield high monolith density but often results in a significant loss in accessible porosity. Herein, we sought to systematically control (1) crystal size, (2) solvation, and (3) compacting pressure in the pelletization process to achieve high packing density without compromising the porosity that makes MOFs functional. It was determined that solvation is the most critical factor among the three factors examined. Solvation that exceeds the pore volume prevents the framework from collapsing, allowing for porosity to be maintained through pelletization. Higher pelletization pressure results in higher packing density, with extensive loss of porosity being observed at a higher pressure if the solvation is below the pore volume. Lastly, we observed that the morphology and size of the MOF particles result in variation in the highest achievable packing efficiency, but these numbers (75%) are still greater than many existing techniques used to form MOFs. Furthermore, we concluded that the application of pressure through pelletization is a suitable and widely applicable technique for forming high-density MOF-monoliths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1978

Catalyst comprising Ir or Ir and Ru for hydrazine decomposition

A catalyst for hydrazine decomposition consisting essentially of a carrier having a pore volume of at least 0.1 cubic centimeters per gram and a specific surface area, measured in square meters per gram, equal to 195 (C.sub.p + 0.013 + 0.736 V.sub.p) where C.sub.p is the specific heat capacity of the carrier at about 25.degree. C in calories per gram per degree and V.sub.p is the pore volume of the carrier in cubic centimeters per gram and metal of the group consisting of iridium, and mixtures consisting of iridium and ruthenium deposited on said carrier in an amount between 20% and about 40% by weight of the catalyst and distributed through the pores thereof in discrete particles sufficiently separated from each other so that they do not sinter or fuse together when the catalyst is at hydrazine decomposition temperature.

Armstrong, Warren E.↗
DOE OSTI2021

Quantitative microstructural investigation of 3D-printed and cast cement pastes using micro-computed tomography and image analysis

Highlights: • Processing alters the microstructure in 3D-printed lamellar cubic element. • A unique patterned and connected pore microstructure network exists. • Micro-channels are connected through micro-pores present at interfaces regions. • Three distinct pore volume domains exists in hardened microstructure. • Volume and frequency of pore, hydrated, and unhydrated clusters are dissimilar. Microstructural phases and mechanical properties of lamellar 3D-printed and cast hardened cement paste (hcp) elements were investigated using a lab-based X-ray microscope at two levels of magnification (0.4× and 4×). K-means clustering was used for quantitative image analysis. The entire volume of intact 3-days-old 3D-printed and cast hcp elements was characterized at 0.4× magnification. Three microstructural features (macro-pores, micro-channels, and interfacial micro-pores) were found to reside in three distinct pore size domains. The largest pores of the 3D-printed element were larger than the largest pores of the reference cast hcp element. Moreover, the smallest pore sizes of the 3D-printed element were found to be smaller than those present in the cast counterparts. Micro-channels were found to be connected to one another through the micro-pores present at interfacial regions, indicating the presence of a uniquely patterned and interconnected pore network. The role of locally weak and porous interfaces on mechanical response and fracture properties is discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Lattice expansion and ligand twist during CO2 adsorption in flexible Cu bipyridine metal–organic frameworks

Flexible metal–organic frameworks (MOFs) can show exceptional selectivity and capacity for adsorption of CO 2 . The incorporation of CO 2 into flexible MOFs that have Cu 2+ coordination centers and organic pillar ligands is accompanied by a distortion of the framework lattice arising from chemical interactions between these components and CO 2 molecules. CO 2 adsorption yields a reproducible lattice expansion that is enabled by the rotation of the pillar ligands. The structures of Cu 2 (pzdc) 2 (bpy) and Cu 2 (pzdc) 2 (bpe), CPL-2 and CPL-5, were evaluated using in situ synchrotron X-ray powder diffraction at room temperature at CO 2 gas pressures up to 50 atm. The structural parameters exhibit hysteresis between pressurization and depressurization. The pore volume within CPL-2 and CPL-5 increases at elevated CO 2 pressure due to a combination of the pillar ligand rotation and the overall expansion of the lattice. Volumetric CO 2 adsorption measurements up to 50 atm reveal adsorption behavior consistent with the structural results, including a rapid uptake of CO 2 at low pressure, saturation above 20 atm, and hysteresis evident as a retention of CO 2 during depressurization. Finally, a significantly greater CO 2 uptake is observed in CPL-5 in comparison with predictions based on CO 2 pressure-induced expansion of the pore volume available for adsorption, indicating that the flexibility of the CPL structures is a key factor in enhancing adsorption capacity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Literature Review and Experimental Observations of the Effects of Salinity, Hardness, Lithology, and ATBS Content on HPAM Polymer Retention for the Milne Point Polymer Flood

Summary At the Milne Point polymer flood (North Slope of Alaska), polymer retention is dominated by the clay, illite. Illite, and kaolinite cause no delay in polymer propagation in Milne Point core material, but they reduce the effective polymer concentration and viscosity by a significant amount (e.g., 30%), thus reducing the efficiency of oil displacement until the full injected polymer concentration is regained [which requires several pore volumes (PVs) of throughput]. This work demonstrates that polymer retention on illite is not sensitive to monovalent ion concentration, but it increases significantly with increased divalent cation concentration. The incorporation of a small percentage of acrylamido tertiary butyl sulfonic acid (ATBS) monomers into hydrolyzed polyacrylamide (HPAM) polymers is shown to dramatically reduce retention. The results are discussed in context with previous literature reports. Bridging adsorption was proposed as a viable mechanism to explain our results. Interestingly, an extensive literature review reveals that polymer retention (on sands and sandstones) is typically only modestly sensitive to the presence of oil. Extensive examination of the literature on inaccessible pore volume (IAPV) suggests the parameter was commonly substantially overestimated, especially in rock/sand more permeable than 500 md (which comprises the vast majority of existing field polymer floods).

Engineering↗
DOE OSTI2020

Metal Organic Frameworks for Xenon Storage Applications

The demand for cheap and convenient xenon storage continues to rise due to its wide spectrum of applications. It is expected that solid-state adsorbents can provide significant advantages over the current isolated stainless-steel tank-based storage technologies. In this context, we investigated metal organic frameworks for use as adsorbents for xenon. Initially, three representative MOFs were synthesized and characterized in terms of Xe storage. The results were used to validate a computational modeling approach, which was later extended to a larger set of materials. The collected results allowed us to rationalize the key parameters (pore volume, surface area, void fraction etc.), which are important for good performance and selection of the best materials for xenon storage

Noble gas, Storage, MOFs↗
DOE OSTI2020

Hybrid Sorbents for 129 I Capture from Contaminated Groundwater

Radioiodine ( 129 I) poses a risk to the environment due to its long half-life, toxicity, and mobility. It is found at the U.S. Department of Energy Hanford Site due to legacy releases of nuclear wastes to the subsurface where 129 I is predominantly present as iodate (IO 3 – ). To date, a cost-effective and scalable cleanup technology for 129 I has not been identified, with hydraulic containment implemented as the remedial approach. Here, novel high-performing sorbents for 129 I remediation with the capacity to reduce 129 I concentrations to or below the US Environmental Protection Agency (EPA) drinking water standard and procedures to deploy them in an ex-situ pump and treat (P&T) system are introduced. Furthermore, this includes implementation of hybridized polyacrylonitrile (PAN) beads for ex-situ remediation of IO 3 – -contaminated groundwater for the first time. Iron (Fe) oxyhydroxide and bismuth (Bi) oxyhydroxide sorbents were deployed on silica substrates or encapsulated in porous PAN beads. In addition, Fe–, cerium (Ce)–, and Bi–oxyhydroxides were encapsulated with anion-exchange resins. The PAN–bismuth oxyhydroxide and PAN–ferrihydrite composites along with Fe- and Ce-based hybrid anion-exchange resins performed well in batch sorption experiments with distribution coefficients for IO 3 – of >1000 mL/g and rapid removal kinetics. Of the tested materials, the Ce-based hybrid anion-exchange resin was the most efficient for removal of IO 3 – from Hanford groundwater in a column system, with 50% breakthrough occurring at 324 pore volumes. The functional amine groups on the parent resin and amount of active sorbent in the resin can be customized to improve the iodine loading capacity. These results highlight the potential for IO 3 – remediation by hybrid sorbents and represent a benchmark for the implementation of commercially available materials to meet EPA standards for cleanup of 129 I in a large-scale P&T system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Heavy Oil Polymer EOR in the Challenging Alaskan Arctic - It Works!

Under co-sponsorship of the US Department of Energy and Hilcorp Alaska LLC the first ever polymer field pilot commenced on 8/28/2018 in the Schrader Bluff heavy oil reservoir at the Milne Point Field on Alaska North Slope (ANS). The primary objective of the pilot is to prove the efficacy of polymer Enhanced Oil Recovery (EOR) to unlock the vast heavy oil resources on ANS. More than two and half years after startup, the polymer injection, supporting laboratory experiments and simulation studies steadily continue. The pilot started injecting hydrolyzed polyacrylamide (HPAM), at a concentration of 1,750 ppm to achieve a target viscosity of 45 cP, into the two horizontal injectors in the flood pattern. Production is monitored in the two horizontal producers. Based on laboratory measurements of polymer viscosity at reservoir conditions, the team decided to reduce polymer concentration to 1,200 ppm since July 2020 in an effort to control injection pressure and optimize polymer utilization. Quality control (QC) on the field ensures uniform polymer solution properties. Representative rock and fluid systems and test conditions are utilized in the corefloods on polymer retention, effect of injection water salinity, polymer loading, and their combinations on oil recovery. A history matched reservoir simulation model for forecasting oil recovery was developed on the basis of all the available field data. Field concerns related to the post-polymer breakthrough impact on flow assurance is addressed via specialized laboratory tests. Notwithstanding early operational disruptions and hydration issues, continuous polymer injection in both injectors has been achieved. To date, 950,000 lbs of polymer or 2 million barrels of polymer solution, equating to 13% of total pore volume (PV), has been placed in the flood pattern, serving as an effective indicator of adequate polymer injectivity. So far, the success of polymer EOR is evident from drastically reduced water cut in the producers, an estimated incremental 1,000 bopd over waterflood, and a favorable polymer utilization of 1.7 lbs/barrel of incremental oil. Polymer breakthrough was observed 26 months after the start of polymer injection. Main observations from corefloods are unusually high polymer retention values in some cases and a positive response to low salinity water. Although the heterogeneity in the flood pattern and exceptionally low water cut pose some challenges, persistent novel and justifiable simulation approaches have resulted in a robust history matched model. Experimental results on produced fluids treatment provide operational guidance for improved oil-water separation and mitigation of heater tube fouling. The ongoing success of the pilot is a key indicator of bringing the team ever closer to meeting the project’s primary objective. The encouraging results of the pilot is one of the drivers that has provided the impetus to apply polymer EOR throughout the Milne Point Field, which would increase oil recovery and extend the economic life of the Trans Alaska Pipeline System. The scientific knowledge, including the many lessons learned from this pilot also has referential value for other potential heavy oil EOR projects throughout the world. The collected data, operational lessons learned, and the overall success of the pilot are summarized in the paper.

None, None↗
NASA NTRS2004

Impregnation of Catalytic Metals in Single-Walled Carbon Nanotubes for Toxic Gas Conversion in Life Support System

Carbon nanotubes (CNTs) possess extraordinary properties such as high surface area, ordered chemical structure that allows functionalization, larger pore volume, and very narrow pore size distribution that have attracted considerable research attention from around the world since their discovery in 1991. The development and characterization of an original and innovative approach for the control and elimination of gaseous toxins using single walled carbon nanotubes (SWNTs) promise superior performance over conventional approaches due to the ability to direct the selective uptake of gaseous species based on their controlled pore size, increased adsorptive capacity due to their increased surface area and the effectiveness of carbon nanotubes as catalyst supports for gaseous conversion. We present our recent investigation of using SWNTs as catalytic supporting materials to impregnate metals, such as rhodium (Rh), palladium (Pd) and other catalysts. A protocol has been developed to oxidize the SWNTs first and then impregnate the Rh in aqueous rhodium chloride solution, according to unique surface properties of SWNTs. The Rh has been successfully impregnated in SWNTs. The Rh-SWNTs have been characterized by various techniques, such as TGA, XPS, TEM, and FTIR. The project is funded by a NASA Research Announcement Grant to find applications of single walled nanocarbons in eliminating toxic gas Contaminant in life support system. This knowledge will be utilized in the development of a prototype SWNT KO, gas purification system that would represent a significant step in the development of high efficiency systems capable of selectively removing specific gaseous for use in regenerative life support system for human exploration missions.

Li, Jing↗