SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Quick room-temperature-cure adhesive bonds polyester-insulated flat electrical cables to metal surfaces and various other substrates. The bond strength of the adhesive may be considerably increased by first applying a commercially available polyamide primer to the polyester film.
A series of candidate materials for use in large balloons was tested and their tensile and shear strength capabilities were compared. The tests were done in a cold box at -68 C (-90 F). Some of these materials were fabricated on a special machine called the flying thread loom. This machine laminates various patterns of polyester yarn to a thin polyester film. The results show that the shear strength of materials changes with the angle selected for the transverse yarns, and substantial increases in biaxial load carrying capabilities, compared to materials formerly used, are possible. The loom capabilities and the test methods are discussed.
Abstract Poly(ethylene terephthalate) (PET) is widely used for its high strength‐to‐weight ratio, gas barrier properties, and chemical resistance. The growing PET use highlights the demand for a better recycling system. Enzymatic recycling, alongside mechanical and chemical methods, is eco‐friendly and yields properties similar to virgin PET. Substrate properties ( T g , crystallinity, and specific surface area [SSA]) and enzyme stability significantly impact conversion efficiency. Higher SSA and lower crystallinity tend to yield improved depolymerization when employing leaf compost‐cutinase (LCC‐ICCG) enzymes. This study explored melt extrusion and foaming as pretreatment techniques to modify PET structural properties, using a low‐cost chemical foaming agent (CFA). The monomer conversion rate and efficiency during depolymerization were measured and related to the processing, extrudate micro‐ and meso‐structure, and polyester type. Pretreated PET substrates showed reduced T g , crystallinity, density, and enhanced SSA, resulting in a 90% mass loss for foamed RPET and VPET substrates within 2 days. In contrast, PET with ~30% of cyclohexanedimethanol comonomer exhibited a nearly 50% lower depolymerization rate, with zero BHET production. It indicates that the combination of low crystallinity, low T g , and high SSA leads to improved monomer conversion. These findings emphasize the significance of amorphization and foaming in enhancing PET enzymatic depolymerization.
This work describes the use of electrochemically generated superoxide (with air as the source of O 2 ) at carbon electrodes as a reagent for the depolymerization of polyesters. Here, we report the electricity-driven selective conversion of these common ester-based wastes into their foundational carboxylate and alkoxide building blocks. The results pave the way for an electrochemical approach to the recovery of molecular materials from ester wastes that uses air and electricity as key reagents for material recycling.
Effect of ionizing radiation on series of saturated polyesters
Belt-to-pulley creep, friction coefficient, and stress relaxation of seamless polyester tape recorder belts
Unsaturated polyester resin (UPR) systems are extensively used in composite materials for applications in the transportation, marine, and infrastructure sectors. There are continually evolving formulations of UPRs that need to be evaluated and optimized for processing. Differential Scanning Calorimetry (DSC) provides valuable insight into the non-isothermal and isothermal behavior of UPRs within a prescribed temperature range. In the present work, non-isothermal DSC tests were carried out between temperatures of 0.0 °C and 250 °C, through different heating and cooling ramp rates. The isothermal DSC tests were carried out between 0.0 and 170 °C. The instantaneous rate of cure of the tested temperatures were measured. The application of an autocatalytic model in a calculator was used to simulate curing behaviors under different processing conditions. As the temperature increased from 10 °C up to 170 °C, the rate of cure reduced, and the heat of reaction increased. The simulated cure behavior from the DSC data showed that the degree of cure (α) maximum value of 71.25% was achieved at the highest heating temperature of 85 °C. For the low heating temperature, i.e., 5 °C, the maximum degree of cure (α) did not exceed 12% because there was not enough heat to activate the catalyst to crosslink further.
Aromatic polyester, PEN-2,6, is improved through cross-linking effected by radiation. Polymer retains properties of high tensile strength and toughness and stability at high temperatures.
Fatigue life tests of polyester film tape recorder belts
Linear aliphatic polyesters preparation by acid chloride synthesis, acid exchange and ester exchange, stressing products purification
Gel permeation chromatography of nominally linear aliphatic polyesters, using tetrahydrofuran solvent at 37 degrees C
Linear aliphatic polyesters unit cell dimensions and crystalline densities
Linear aliphatic polyesters, calculating conformational contribution to heats and entropies of fusion
Linear aliphatic polyesters melting point, fusion heat and entropy correlations to molecular parameters
Polyester formation by Escherichia coli ribosome catalyzed alpha-hydroxy acid incorporation into polymer chain
The relative toxicity in rats resulting from a 30 minute exposure to the combustion products of two materials, Tedlar and fluorenone-polyester film was assessed. The combustion products were generated into a static exposure system using a laboratory-scale furnace. The toxicity was assessed using the primary measurements employed in a more detailed overall toxicity evaluation. The toxicological events observed during the 30 minute exposure are reported.
An unsaturated polyester, such as propylene glycolmaleic acid phthalic acid prepolymer dissolved in styrene is interpolymerized with an ultraviolet absorber and/or an antioxidant. The unsaturated chain may be filled with H or lower alkyl such as methyl and tertiary alkyl such as tertiary butyl. A polymer stable to exposure to the outdoors without degradation by ultraviolet radiation, thermal and/or photooxidation is formed.
A tapered tubular polyester sleeve is described to serve as the flexible foundation for a spacesuit limb covering. The tube has a large end and a small end with a length to be determined. The ratio of taper is also determined by scale factors. All the warp yarns extend to the large end. A requisite number of warp yarns extend the full length of the sleeve. Other warp yarns extend from the large end but are terminated along the length of the sleeve. It is then woven with a filling yarn which extends in a full circle along the full length of the sleeve to thereby define the tapered sleeve. The sleeve after fabrication is then placed on a mandrel, heated in an oven, and then attached to the arm or other limb of the spacesuit.