Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pelleting Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Low cost silicon solar array project silicon materials task: Establishment of the feasibility of a process capable of low-cost, high volume production of silane (step 1) and the pyrolysis of silane to semiconductor-grade silicon (step 2)

Extended operation of a small process-development unit routinely produced high quality silane in 97+% yield from dichlorosilane. The production rate was consistent with design loadings for the fractionating column and for the redistribution reactor. A glass fluid-bed reactor was constructed for room temperature operation. The behavior of a bed of silcon particles was observed as a function of various feedstocks, component configurations, and operating conditions. For operating modes other than spouting, the bed behaved in an erratic and unstable manner. A method was developed for casting molten silicon powder into crack-free solid pellets for process evaluation. The silicon powder was melted and cast into thin walled quartz tubes that sacrificially broke on cooling.

Breneman, W. C.↗
DOE OSTI2022

Pilot-Scale Pelleting Tests on High-Moisture Pine, Switchgrass, and Their Blends: Impact on Pellet Physical Properties, Chemical Composition, and Heating Values

In this study, we evaluated the pelleting characteristics of southern yellow pine (SYP), switchgrass (SG), and their blends for thermochemical conversion processes, such as pyrolysis and gasification. Using a pilot-scale ring-die pellet mill, we specifically assessed the impact of blend moisture, length-to-diameter (L/D) ratio in the pellet die, and ratio of pine to SG on the physico-chemical properties of the resulting pellets. We found that an increase in pine content by 25–50% marginally affected the bulk density; however, it also led to an increase in calorific value by 7% and a decrease in ash content by 72%. A moisture content of 25% (wet basis) and an L/D ratio of 5 resulted in poor pellet durability at <90% and bulk density values of <500 kg/m 3 , but increasing the L/D ratio to 9 and lowering the moisture content to 20% (w.b.) improved the pellet durability to >90% and the bulk density to >500 kg/m 3 . Blends with ≥50% pine content resulted in lower energy consumption, while a lower L/D ratio resulted in higher pelleting energy. Based on these findings, we successfully demonstrated the high-moisture pelleting of 2.5 ton of pine top residues blended with SG at 60:40 and 50:50 ratios. The quality of the pellets was monitored off-line and at-line by near infrared (NIR) spectroscopy. Multivariate models constructed by combining the NIR data and the pelleting process variables could successfully predict the pine content (R 2 = 0.99), higher heating value (R 2 = 0.98), ash (R 2 = 0.95), durability (R 2 = 0.94), and bulk density (R 2 = 0.86) of the pellets. Thus, we established how blending and densification of SYP and SG biomass could improve feedstock specifications and that NIR spectroscopy can effectively monitor the pellet properties during the high-moisture pelleting process.

09 BIOMASS FUELS↗
DOE OSTI2024

Spark plasma sintering of fuel meats for U 3 O 8 based dispersion fuels

Research and test reactors often use dispersion-type fuel due to its increased thermal conductivity and burn-up capabilities compared to conventional fuel. Al-U 3 O 8 (aluminumtriuranium octaoxide) dispersion fuels have several advantages over their competitors, such as higher service temperature and better stability of oxygen stoichiometry. However, the two-step fabrication of dispersion fuel causes undesirable porosity in cold-pressed fuel meats that is preserved in co-extruded fuel plates. To combat this, spark plasma sintering (SPS) was used for the fabrication of Al-15, 20, and 30 vol% U 3 O 8 and 8 and 12 vol% Mo-U 3 O 8 fuel meats for the Al-U 3 O 8 time. The in situ SPS data was used to construct and validate Master Sintering Curves (MSCs) with accuracies in Al fuels at 0.02 g/cm 3 , and Mo fuels at 0.07 and 0.17 g/cm 3 . The as-sintered fuel meats were characterised using x-ray diffraction (XRD) and scanning electron microscopy (SEM) to understand chemical and physical changes following the SPS process. The pellets exhibited very high relative densities, the U 3 O 8 was observed to undergo reduction to UO 2 .

Aluminium↗
DOE OSTI2021

Biomass Size Reduction, Drying, and Densification

The overall objective is to solve the particle attrition issue during biomass grinding and pelleting and to enable pelleting as a viable option for production of on-spec material or conversion-ready cellulosic feedstocks.

09 BIOMASS FUELS↗
DOE OSTI2024

Biochar-compost-based controlled-release nitrogen fertilizer intended for an active microbial community

Nitrogen (N) fertilizers in agriculture suffer losses by volatilization of N to the air, surface runoff and leaching into the soil, resulting in low N use efficiency (NUE) (< 50%) and raising severe environmental pollutions. Controlled- release nitrogen fertilizers (CRNFs) can control the release of N nutrients to NUE in crop production. Different methods were used to develop new CRNFs. However, different CRNF technologies are still underdeveloped due to inadequate controlling on N releasing time and/or unsustainable diffusion. The study on the influences of CRNF processing parameters on microbial conditions are lacking when the CRNFs composed of various bio-ingredients such as biochar, composts, and biowaste. The complexity of processing methods, material biodegradability, and other physical properties make current CRNFs of questionable value in agricultural production. This research aims to develop a novel biochar-compost-based controlled-release urea fertilizer (BCRUF) to preserve microbial properties carried by the compost. The BCRUF was synthesized by pelletizing the 50:50 (dry, wt/wt) mixture of biochar and compost. BCRUF was loaded with urea and then spray-coated with polylactic acid (PLA). The releasing time of two types of BCRUFs, coated and uncoated with PLA, for 80% of N release in water was up to 6 h at three different temperatures (4, 23, and 40 °C), compared to conventional urea fertilizer and commercial environmentally smart N (ESN) fertilizer. The releasing time of coated BCRUF for 80% N release in soil was up to 192 h (8 days). Fourier-transform infrared spectroscopy (FTIR) analysis revealed that no new functional groups were found in the release solution, indicating no new chemical hazards generated. The differential scanning calorimetry (DSC) tests also verified that its thermal stability could be up to 160 °C. The microbe populations in the BCRUF pellets were reduced after the pelleting and drying processes in BCRUF fabrication, but a few bacteria can endure in the air-drying process. BCRUF pellets soaked in water for 4 days retained some bacteria. The BCRUF showed very promising characteristics to improve NUE and sustainability in agricultural production.

58 GEOSCIENCES↗
DOE OSTI2021

Explore the Potential to Formulate Feedstock Blends from Diverse Biomass inputs for Improved Processing Performance at Lower Costs

This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat-die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of >550 kg/m3 and durability of >95. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption. Tests were also conducted on blends of pine and switchgrass using a pilot scale pellet mill by varying the blend moisture content and compression ratio of the pellet die. Pelleting tests on pure pine and switchgrass and their blends in a pilot scale ring die pellet mill with a throughput of 1 ton/h has indicated pellets with durability >500 kg/m3 and durability in the range of >90 and >95 %. The demonstration of high moisture pelleting of blends of 2- and 6-inch top pine residues and switchgrass blends indicated that good quality pellets with durability >90 % and bulk density of >500 kg/m3 can be produced.

09 BIOMASS FUELS↗
DOE OSTI2025

[LCA UP] Biomass Pelletization (2022)

This unit process quantifies the energy requirements that are expected to result from woody biomass or torrefied woody biomass pelletization.

Group - Basic Process↗
NASA NTRS1993

Cleaning By Blasting With Pellets Of Dry Ice

Dry process strips protective surface coats from parts to be cleaned, without manual scrubbing. Does not involve use of flammable or toxic solvents. Used to remove coats from variety of materials, including plastics, ceramics, ferrous and nonferrous metals, and composites. Adds no chemical-pollution problem to problem of disposal of residue of coating material. Process consists of blasting solid carbon dioxide (dry ice) pellets at surface to be cleaned. Pellets sublime on impact and pass into atmosphere as carbon dioxide gas. Size, harness, velocity, and quantity of pellets adjusted to suit coating material and substrate.

Fody, Jody↗
DOE OSTI2021

Synchrotron X-ray microtomography and multifractal analysis for the characterization of pore structure and distribution in softwood pellet biochar

Biochar pores in the micrometer range (1–100 µm) derive from cellular structures of the plant biomass subjected to pyrolysis or can be the result of mechanical processing, such as pelleting. In this study, synchrotron X-ray microtomography was used to investigate the internal pore structure of softwood pellet biochar produced by slow pyrolysis at 550 and 700 °C. The microtomographic data sets consisted of 2025 images of 2560 × 2560 voxels with a voxel side length of 0.87 µm. The three-dimensional reconstructions revealed that pelleting and pyrolysis significantly altered the pore structures of the wood feedstock, creating a network of connected pores between fragments that resembled the wood morphology. While higher pyrolysis temperature increased the specific surface area (as determined by BET nitrogen adsorption), it did not affect the total observed porosity. Multifractal analysis was applied to assess the characteristics of the frequency distribution of pores along each of the three dimensions of reconstructed images of five softwood pellet biochar samples. The resulting singularity and Rényi spectra (generalized dimensions) indicated that the distribution of porosity had monofractal scaling behavior, was homogeneous within the analyzed volumes and consistent between replicate samples. Moreover, the pore distributions were isotropic (direction-independent), which is in strong contrast with the anisotropic pore structure of wood. As pores at the scale analyzed in this study are relevant, for example, for the supply of plant accessible water and habitable space for microorganisms, our findings combined with the ability to reproduce biochar with such pore distribution offer substantial advantages in various biochar applications.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Characterization of textile-grade carbon fiber polypropylene composites

In this work, we consider low-cost carbon fiber produced with a textile-grade precursor. The objective of the study is to investigate textile-grade carbon-fiber-reinforced-polypropylene composites (TCF-PP) from compounded pellets for mechanical and thermal characterization. Four sets of pellets with 1%, 5%, 10%, and 15% reinforcement were manufactured using textile-grade carbon fiber (TCF) and polypropylene (PP) by twin-screw compounding. The addition of TCFs through gravimetric feeder directly in the extruder resulted in lower fiber content; however, side feeder has shown good potential. The pellets were further processed in extrusion compression molding to manufacture plaques. An increase in fiber loading has a negligible effect on fiber attrition as fiber length distribution variation between 1% and 15% reinforced pellets was very small. The addition of TCFs in PP showed a significant improvement in mechanical properties. The tensile strength and modulus of the composite were 26% and 161%, respectively, improved by the addition of 10 wt% TCF. Similar results were observed in the flexure test. However, the impact properties were reduced by 25.54% by the addition of 15% TCF.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Trace Impurities Identified as Forensic Signatures in CMX-5 Fuel Pellets Using X-ray Spectroscopic Techniques

We report that small-particle analysis is a highly promising emerging forensic tool for analysis of interdicted special nuclear materials. Integration of microstructural, morphological, compositional, and molecular impurity signatures could provide significant advancements in forensic capabilities. We have applied rapid, high-sensitivity, hard X-ray synchrotron chemical imaging to analyze impurity signatures in two differently fabricated fuel pellets from the 5th Collaborative Materials Exercise (CMX5) of the IAEA Nuclear Forensics International Working Group. The spatial distributions, chemical compositions, and morphological and molecular characteristics of impurities were evaluated using X-ray absorption near-edge structure (XANES) and X-ray fluorescence chemical imaging to discover principal impurities, their granularity, particle sizes, modes of occurrence (distinct grains vs incorporation in the UO 2 lattice), and sources and mechanisms of incorporation. Differences in UO 2+x stoichiometry were detected at the microscale in nominally identical UO 2 ceramics (CMX5-A and CMX5-B), implying the presence of multiple UO 2 host phases with characteristic microstructures and feedstock compositions. Al, Fe, Ni, W, and Zr impurities and integrated impurity signature analysis identified distinctly different pellet synthesis and processing methods. For example, two different Al, W, and Zr populations in the CMX5-B sample indicated a more complex processing history than the CMX5-A sample. K-edge XANES measurements reveal both metallic and oxide forms of Fe and Ni but with different proportions between each sample. Altogether, these observations suggest multiple sources of impurities, including fabrication (e.g., force-sieving) and feedstock (mineral oxides). This study demonstrates the potential of synchrotron techniques to integrate different signatures across length scales (angstrom to micrometer) to detect and differentiate between contrasting UO 2 fuel fabrication techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Pressure Response Optimization of an Eddy Current-Driven Flyer Plate Valve for the ITER Shattered Pellet Injection System

One technique for mitigating disruptions in a tokamak is shattered pellet injection (SPI). SPI is a process in which a large solid pellet consisting of deuterium, neon, or argon is desublimated in a pipe gun barsrel and launched downstream. Pellets are shattered just before entering the plasma by an impact with an angled tube. Injection of these materials into the plasma radiates stored thermal energy, limits current decay rates, suppresses the generation of runaway electrons, and dissipates runaway electrons if necessary. A critical element of the SPI system is a fast-acting valve that releases high-pressure gas to dislodge and accelerate pellets directly, or indirectly via a mechanical punch. A prototype valve sized for the ITER SPI system has been designed and fabricated. A pulsed high-voltage power supply energizes the valve’s internal magnetic coil, which induces eddy currents in the adjacent flyer plate resulting in a repulsive force between the flyer plate and the coil. The flyer plate action lifts a valve seat, allowing high-pressure gas to flow from the valve plenum to the downstream (breech) location of the pellet or mechanical punch. All of the valve’s internal components are designed to operate in ITER-level static background magnetic fields. Here, a study was conducted to optimize the downstream pressure response for a range of valve sizes and operating pressures. In particular, the study analyzes the breech pressure response associated with varying plenum pressures as well as varying breech volumes. A computational fluid dynamics simulation was built in STAR-CCM+ and validated against data from laboratory experiments. The resulting simulation outputs, in the form of downstream responses for a variety of initial plenum pressures and breech volumes, will be used as a complement to experimental data to ensure the pressure pulse is suitable for pellet survivability. These data, combined with studies on pellet shear strength and shock response, will be applied to optimization of overall operating parameters of the ITER SPI system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Characterization of Preliminary Powder Production and Consolidation for Advanced LEU Fuel Concepts

A set of novel uranium-based alloys has been proposed for use in advanced LEU fuel systems that utilize powder metallurgical methods for fabrication of the fuel forms. This study seeks to evaluate the effectiveness of current fabrication methods to produce powder of each of the candidate alloys and consolidate composite systems. Powder samples were produced via atomization and analyzed for particle size, shape, and microstructure utilizing sieving methods and scanning electron microscopy (SEM). Preliminary pellet consolidation tests were conducted with the atomized powder using a press and sinter method. The resulting pellets were analyzed via SEM to evaluate the morphology of the composite system. These preliminary tests demonstrate the ability to produce powder but did not yield the desired quality of powder and impacted the ability to fabricate a fully dense pellet. A refined process is under development to produce a higher yield of small (<250 µm) spherical powder.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Fractionation of Lignocellulosic Biomass into High-Value Products - CRADA Report

Idaho National Laboratory (INL) has developed a process for adding value in the biomass feedstock supply chain. The key aspects of this process include: (1) anaerobic and chemical treatment of biomass during storage, (2) fractionation of biomass into conversion-ready feedstock and high-value coproducts, and (3) high-moisture pelleting to increase the bulk density and stabilize the feedstock. The purpose of the chemical treatment is to overcome the recalcitrant nature of the feedstock to improve the biochemical conversion process of breaking down the biomass into sugars. To maximize the utilization of the biomass, the feedstock can be fractionated into hemicellulose and lignin rich fractions. Finally, to increase the materials overall energy density, produce a shelf-stable material, and to facilitate transport, the feedstock is densified in a pelleting process. The first two steps of the processes have been verified at bench scale showing an improvement in theoretical glucose yield from 23.1% to 44.5% and an improvement in theoretical xylose yield from 8.9% to 23.1% from ground corn stover. It is hypothesized that densification will further increase the carbohydrate yield in the sample. The goal of this project was to evaluate the technical feasibility and process economics of the above process and to provide preliminary data to Golden Leaf Energy, Inc to access its potential commercialization for converting biomass to ethanol and renewable chemicals. Corn stover (CS), the largest available agricultural residue, and Chinese tallow (CT), an invasive wood species with no current commercial value, were chosen as feedstocks for this project.

09 BIOMASS FUELS↗
DOE OSTI2026

Are the U.S. Biorefineries Over the Hurdle of 2000 Ton Daily Throughput Yet?

The efficient utilization of lignocellulosic biomass for biofuel and biochemical production is hindered by material handling issues such as clogging and segregation among other challenges. Preprocessing methods such as drying, screening, and milling have improved conversion yield but have not sufficiently enhanced flowability, especially herbaceous biomass. The poor flowability of herbaceous biomass is rooted in some particle attributes that remain less altered by those methods, e.g., irregular particle shape, high roughness, and high compressibility, making it hard to scale up throughput to a key benchmark for a biorefinery – 2000 ton per day. Applying additional preprocessing methods like pelletization and torrefaction to drastically change those particle attributes can improve flow and handling but has not been comprehensively verified through test. The flowability of herbaceous biomass feedstock formats generated by three different preprocessing methods was recently assessed at Idaho National Laboratory’s Biomass Feedstock National User Facility: first, loose particles size reduced from as-received materials; second, pellets produced from an efficient densification process; and third, powders milled from torrefied pellets. Benchmarking tests including static angle of repose, basic flow energy measured in a powder rheometer, and discharge flow in an adjustable hopper, were conducted to evaluate those feedstock formats. Beyond the capacity of existing experimental apparatuses, a digital engineering approach involving flow simulations and AI models were used to identity the material attributes and processing parameters that have dominant influences on flow throughput. Techno-economic analysis focusing on hopper flow as a typical material handling operation was conducted for those feedstock formats. Perspectives will be discussed on whether the 2000-ton daily throughput for a biorefinery is achievable at an acceptable cost by using any of the tested preprocessing methods.

09 - BIOMASS FUELS↗
DOE OSTI2026

Spectroscopic Characterization of Plasmoid Properties During Pellet Fueling in W7-X

This study utilizes a spectroscopic approach to investigate the properties of plasmoids that are formed during the process of cryogenic hydrogen pellet fueling in the Wendelstein 7-X (W7-X) stellarator. An analysis of the Balmer series emissions was conducted using a diagnostic that was installed during the 2024 operational campaign. Electron temperature, density, and plasma beta ( β ) values can be inferred from the emissions of radiation from the ablation plasmoid. These values are essential for validating pellet ablation models and, in the future, optimizing fueling strategies in steady-state fusion devices.

Cryogenic hydrogen pellets↗
DOE OSTI2020

Thermal Process Technology for Nuclear Applications - 20379

ANSTO's Synroc technology has been developed to provide a safe, secure matrix for the immobilization and final disposal of radioactive waste. Synroc technology will be used to manage radioactive wastes from the production of the radioisotope Molybdenum-99 (Mo-99). This paper shall outline various stages of the process development with specific reference to the thermal treatment technology of calcination. Calcination is a key step in the Synroc process [1-2].The rotary thermal processing system includes: an advanced heating element design for increased robustness and ease of remote operation and maintenance, an enhanced modular design of components for ease of remote maintenance in a hot cell and in compliance with hot cell radioactive environment requirements for safety, reliability and maintainability. In addition to thermal treatment of waste from nuclear medicine production, this technology provides solutions for a variety of nuclear materials processing applications including sintering UO{sub 2} pellets for reactor fuel rods, oxidation of UO{sub 2} pellets, swarf, and powder to U{sub 3}O{sub 8}, de-nitration of Uranyl nitrate and hydrofluorination of UO{sub 2} pellets. The paper will also discuss thermal processing solutions for a range of nuclear applications. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗