Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSURE VESSEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Carbon fiber internal pressure vessels

Internal pressure vessels were designed; the filament was wound of carbon fibers and epoxy resin and tested to burst. The fibers used were Thornel 400, Thornel 75, and Hercules HTS. Additional vessels with type A fiber were made. Polymeric linears were used, and all burst testing was done at room temperature. The objective was to produce vessels with the highest attainable PbV/W efficiencies. The type A vessels showed the highest average efficiency: 2.56 x 10 to the 6th power cm. Next highest efficiency was with Thornel 400 vessels: 2.21 x 10 to the 6th power cm. These values compare favorably with efficiency values from good quality S-glass vessels, but strains averaged 0.97% or less, which is less than 1/3 the strain of S-glass vessels.

Simon, R. A.↗

Evaluation of Data-Logging Transducer to Passively Collect Pressure Vessel p/T History

Pressure vessels owned and operated by NASA are required to be regularly certified per agency policy. Certification requires an assessment of damage mechanisms and an estimation of vessel remaining life. Since detail service histories are not typically available for most pressure vessels, a conservative estimate of vessel pressure/temperature excursions is typically used in assessing fatigue life. This paper details trial use of a data-logging transducer to passively obtain actual pressure and temperature service histories of pressure vessels. The approach was found to have some potential for cost savings and other benefits in certain cases.

Wnuk, Stephen P.↗

Long-life assessment of graphite epoxy materials for Space Station Freedom pressure vessels

Graphite/epoxy composite overwrapped pressure vessels are being considered for use on Space Station Freedom because of their light weight and high efficiency. These composite pressure vessels weigh roughly one-third of comparable all-metal aluminum pressure vessels, and could result in a 15,000-lb weight saving for the propulsion and fluid management and distribution systems. These vessels must resist failures under sustained pressure loads for crew safety considerations and adequate protection of the space structure during their 30-yr life. Weibull statistical analysis techniques have been applied, and a model developed, for predicting long-term stress-rupture behavior based on published short-term test data on composite strands and pressure vessels. Graphite/epoxy materials are calculated to have a 99.99-percent probability of surviving stress rupture for 30 yr under a sustained load of 50 percent ultimate failure strength. Stress-rupture lifetimes are predicted to increase as the size of the pressure vessels increases in support of the viscoelastic load-transfer mechanism proposed for stress rupture of fiber/epoxy composite materials.

Thomas, Donald A.↗

Application of the ASME Boiler and Pressure Vessel Code in the Design of SRF Cavities at Fermilab

Jacketed Superconducting Radio Frequency (SRF) cavities structurally comprise of an inner niobium vessel surrounded by a liquid helium containment vessels. The pressure of the helium bath and/or its volume might be such that a jacketed SRF cavity shall be considered a system of pressure vessels. Thus, methods described in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC) should be used to analyze the structural soundness of jacketed SRF cavities. This paper will report the use of the set of rules developed at Fermilab for the design of SRF cavities, such as jacketed 1.3 GHz cavities for LCLS-II HE and jacketed Single Spoke Resonator type~2 (SSR2) for PIP-II, to ensure a similar level of safety as prescribed by the ASME BPVC.

43 PARTICLE ACCELERATORS↗

Apollo experience report: Pressure vessels

The Apollo spacecraft pressure vessels, associated problems and resolutions, and related experience in evaluating potential problem areas are discussed. Information is provided that can be used as a guideline in the establishment of baseline criteria for the design and use of lightweight pressure vessels. One of the first practical applications of the use of fracture-mechanics technology to protect against service failures was made on Apollo pressure vessels. Recommendations are made, based on Apollo experience, that are designed to reduce the incidence of failure in pressure-vessel operation and service.

Ecord, G. M.↗

Curved and conformal high-pressure vessel

A high-pressure vessel is provided. The high-pressure vessel may comprise a first chamber defined at least partially by a first wall, and a second chamber defined at least partially by the first wall. The first chamber and the second chamber may form a curved contour of the high-pressure vessel. A modular tank assembly is also provided, and may comprise a first mid tube having a convex geometry. The first mid tube may be defined by a first inner wall, a curved wall extending from the first inner wall, and a second inner wall extending from the curved wall. The first inner wall may be disposed at an angle relative to the second inner wall. The first mid tube may further be defined by a short curved wall opposite the curved wall and extending from the second inner wall to the first inner wall.

42 ENGINEERING↗

Flexible Composite-Material Pressure Vessel

A proposed lightweight pressure vessel would be made of a composite of high-tenacity continuous fibers and a flexible matrix material. The flexibility of this pressure vessel would render it (1) compactly stowable for transport and (2) more able to withstand impacts, relative to lightweight pressure vessels made of rigid composite materials. The vessel would be designed as a structural shell wherein the fibers would be predominantly bias-oriented, the orientations being optimized to make the fibers bear the tensile loads in the structure. Such efficient use of tension-bearing fibers would minimize or eliminate the need for stitching and fill (weft) fibers for strength. The vessel could be fabricated by techniques adapted from filament winding of prior composite-material vessels, perhaps in conjunction with the use of dry film adhesives. In addition to the high-bias main-body substructure described above, the vessel would include a low-bias end substructure to complete coverage and react peak loads. Axial elements would be overlaid to contain damage and to control fiber orientation around side openings. Fiber ring structures would be used as interfaces for connection to ancillary hardware.

Brown, Glen↗

Stress Rupture Life Reliability Measures for Composite Overwrapped Pressure Vessels

Composite Overwrapped Pressure Vessels (COPVs) are often used for storing pressurant gases onboard spacecraft. Kevlar (DuPont), glass, carbon and other more recent fibers have all been used as overwraps. Due to the fact that overwraps are subjected to sustained loads for an extended period during a mission, stress rupture failure is a major concern. It is therefore important to ascertain the reliability of these vessels by analysis, since the testing of each flight design cannot be completed on a practical time scale. The present paper examines specifically a Weibull statistics based stress rupture model and considers the various uncertainties associated with the model parameters. The paper also examines several reliability estimate measures that would be of use for the purpose of recertification and for qualifying flight worthiness of these vessels. Specifically, deterministic values for a point estimate, mean estimate and 90/95 percent confidence estimates of the reliability are all examined for a typical flight quality vessel under constant stress. The mean and the 90/95 percent confidence estimates are computed using Monte-Carlo simulation techniques by assuming distribution statistics of model parameters based also on simulation and on the available data, especially the sample sizes represented in the data. The data for the stress rupture model are obtained from the Lawrence Livermore National Laboratories (LLNL) stress rupture testing program, carried out for the past 35 years. Deterministic as well as probabilistic sensitivities are examined.

Murthy, Pappu L. N.↗

Interrelationship of Nondestructive Evaluation Methodologies Applied to Testing of Composite Overwrapped Pressure Vessels

Composite Overwrapped Pressure Vessels (COPVs) are commonly used in spacecraft for containment of pressurized gases and fluids, incorporating strength and weight savings. The energy stored is capable of extensive spacecraft damage and personal injury in the event of sudden failure. These apparently simple structures, composed of a metallic media impermeable liner and fiber/resin composite overwrap are really complex structures with numerous material and structural phenomena interacting during pressurized use which requires multiple, interrelated monitoring methodologies to monitor and understand subtle changes critical to safe use. Testing of COPVs at NASA Johnson Space Center White Sands T est Facility (WSTF) has employed multiple in-situ, real-time nondestructive evaluation (NDE) methodologies as well as pre- and post-test comparative techniques to monitor changes in material and structural parameters during advanced pressurized testing. The use of NDE methodologies and their relationship to monitoring changes is discussed based on testing of real-world spacecraft COPVs. Lessons learned are used to present recommendations for use in testing, as well as a discussion of potential applications to vessel health monitoring in future applications.

Leifeste, Mark R.↗

Material Issues in Space Shuttle Composite Overwrapped Pressure Vessels

Composite Overwrapped Pressure Vessels (COPV) store gases used in four subsystems for NASA's Space Shuttle Fleet. While there are 24 COPV on each Orbiter ranging in size from 19-40", stress rupture failure of a pressurized Orbiter COPV on the ground or in flight is a catastrophic hazard and would likely lead to significant damage/loss of vehicle and/or life and is categorized as a Crit 1 failure. These vessels were manufactured during the late 1970's and into the early 1980's using Titanium liners, Kevlar 49 fiber, epoxy matrix resin, and polyurethane coating. The COPVs are pressurized periodically to 3-5ksi and therefore experience significant strain in the composite overwrap. Similar composite vessels were developed in a variety of DOE Programs (primarily at Lawrence Livermore National Laboratories or LLNL), as well as for NASA Space Shuttle Fleet Leader COPV program. The NASA Engineering Safety Center (NESC) formed an Independent Technical Assessment (ITA) team whose primary focus was to investigate whether or not enough composite life remained in the Shuttle COPV in order to provide a strategic rationale for continued COPV use aboard the Space Shuttle Fleet with the existing 25-year-old vessels. Several material science issues were examined and will be discussed in this presentation including morphological changes to Kevlar 49 fiber under stress, manufacturing changes in Kevlar 49 and their effect on morphology and tensile strength, epoxy resin strain, composite creep, degradation of polyurethane coatings, and Titanium yield characteristics.

Sutter, James K.↗

Conformable Hydrogen Storage Pressure Vessel

Existing commercially available hydrogen storage technologies are largely based on bulky and costly pressure vessels. These pressure vessels come in various forms, ranging from Type I steel cylinders to Type III and Type IV composite wrapped cylinders with metallic or polymer liners. In efforts to increase the pressure vessel storage density and meet DOE hydrogen storage targets, manufacturers are making incremental improvements. This approach alone is unlikely to meet DOE hydrogen storage targets and increase adoption of hydrogen fuel cell vehicles. The project team, led by the Center for Transportation and the Environment (CTE) and consisting of High Energy Coil Reservoirs, LLC (HECR) and The University of Texas at Austin's Center for Electromechanics (UT-CEM), has investigated a transformational hydrogen storage technology using high pressure modulus polymeric pressure vessels. These vessels are constructed by overwrapping an extruded thermoplastic elastomeric resin liner with high performance tensile fiber. This technology is used in commercially available compressed air storage for firefighters. The result is a lightweight, flexible, non-explosive, and non-fragmenting pressure vessel that can be shaped (prior to pressurization) to conform to specific applications. Although this project was funded to investigate the potential for this technology for vehicle applications, a potential significant cost reduction allowed with this approach may make it effective for high pressure ground storage as well. As part of Phase I of this project, the research team demonstrated a Kevlar™ over-braid that achieves a burst pressure in excess of 3.1X the operating pressure of 700 bar. The conformable vessel is able to achieve this pressure rating with reduced weight and cost when compared to Type IV vessels. The researchers also identified two potential resins to serve as the liner of the vessel. These resins have excellent hydrogen barrier properties that could enable a liner thickness of 0.06 inches or less; however, difficulties in manufacturing the core due to the extrusion manufacturing processes required testing with prototype resins as commercially available resins were not found that had the required properties. The team was able to build and test a vessel with one such blend, which outperformed the baseline Hytrel resin materials but did not meet the project hydrogen permeability rate goals.

08 HYDROGEN↗

Continued Development of Meandering Winding Magnetometer (MWM (Register Trademark)) Eddy Current Sensors for the Health Monitoring, Modeling and Damage Detection of Composite Overwrapped Pressure Vessels

Composite Overwrapped Pressure Vessels (COPVs) are used in essentially all NASA spacecraft, launch. vehicles and payloads to contain high-pressure fluids for propulsion, life support systems and science experiments. Failure of any COPV either in flight or during ground processing would result in catastrophic damage to the spacecraft or payload, and could lead to loss of life. Therefore, NASA continues to investigate new methods to non-destructively inspect (NDE) COPVs for structural anomalies and to provide a means for in-situ structural health monitoring (SHM) during operational service. Partnering with JENTEK Sensors, engineers at NASA, Kennedy Space Center have successfully conducted a proof-of-concept study to develop Meandering Winding Magnetometer (MWM) eddy current sensors designed to make direct measurements of the stresses of the internal layers of a carbon fiber composite wrapped COPV. During this study three different MWM sensors were tested at three orientations to demonstrate the ability of the technology to measure stresses at various fiber orientations and depths. These results showed good correlation with actual surface strain gage measurements. MWM-Array technology for scanning COPVs can reliably be used to image and detect mechanical damage. To validate this conclusion, several COPVs were scanned to obtain a baseline, and then each COPV was impacted at varying energy levels and then rescanned. The baseline subtracted images were used to demonstrate damage detection. These scans were performed with two different MWM-Arrays. with different geometries for near-surface and deeper penetration imaging at multiple frequencies and in multiple orientations of the linear MWM drive. This presentation will include a review of micromechanical models that relate measured sensor responses to composite material constituent properties, validated by the proof of concept study, as the basis for SHM and NDE data analysis as well as potential improvements including design changes to miniaturize and make the sensors durable in the vacuum of space

Russell, Richard↗

NASA Engineering and Safety Center Technical Bulletin No. 21-04: Evaluating Appropriateness of LEFM Tools for COPV and Metal Pressure Vessel Damage Tolerance Life Verification

Human spaceflight composite overwrapped pressure vessels (COPVs) and metal pressure vessels can use linear elastic fracture mechanics (LEFM) analysis to demonstrate damage tolerance life per ANSI/AIAA-S-081 for COPVs and ANSI/AIAA-S-080 for metal pressure vessels. LEFM analysis assumptions require that the crack tip plastic zone is small relative to the crack size and is completely surrounded by elastically responding material. Test and analysis have shown that LEFM tools (i.e., NASGRO*) can provide unconservative crack growth predictions for cracks in COPV liners that violate LEFM assumptions. COPV and metal pressure vessel designers should evaluate and address the violation of LEFM plasticity assumptions before using LEFM analysis tools for damage tolerance life verification.

COPV↗

PWR decay heat removal system in which steam from the pressurizer drives a turbine which drives a pump to inject water into the reactor pressure vessel

In conjunction with a pressurized water reactor (PWR) and a pressurizer configured to control pressure in the reactor pressure vessel, a decay heat removal system comprises a pressurized passive condenser, a turbine-driven pump connected to suction water from at least one water source into the reactor pressure vessel; and steam piping configured to deliver steam from the pressurizer to the turbine to operate the pump and to discharge the delivered steam into the pressurized passive condenser. The pump and turbine may be mounted on a common shaft via which the turbine drives the pump. The at least one water source may include a refueling water storage tank (RWST) and/or the pressurized passive condenser. A pressurizer power operated relief valve may control discharge of a portion of the delivered steam bypassing the turbine into the pressurized passive condenser to control pressure in the pressurizer.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

PWR decay heat removal system in which steam from the pressurizer drives a turbine which drives a pump to inject water into the reactor pressure vessel

In conjunction with a pressurized water reactor (PWR) and a pressurizer configured to control pressure in the reactor pressure vessel, a decay heat removal system comprises a pressurized passive condenser, a turbine-driven pump connected to suction water from at least one water source into the reactor pressure vessel; and steam piping configured to deliver steam from the pressurizer to the turbine to operate the pump and to discharge the delivered steam into the pressurized passive condenser. The pump and turbine may be mounted on a common shaft via which the turbine drives the pump. The at least one water source may include a refueling water storage tank (RWST) and/or the pressurized passive condenser. A pressurizer power operated relief valve may control discharge of a portion of the delivered steam bypassing the turbine into the pressurized passive condenser to control pressure in the pressurizer.

Graham, Thomas G.↗

Plan for Post-Irradiation Examination of Zion Reactor Pressure Vessel Beltline Materials

The reactor pressure vessel (RPV) is a potentially life-limiting component in light-water reactors (LWR) because replacement of the RPV is not considered a viable option. Researchers studying the effects of radiation on RPV materials have long been interested in evaluating service-irradiated materials to assess currently available models for predicting radiation embrittlement of RPV steels. The decommissioning of the Zion Unit 1 NPP in Zion, Illinois presents a unique opportunity for characterization of an actual reactor pressure vessel (RPV) material after inservice degradation. The main interests in this case are the belt-line weld and base metals. Through-RPV wall thickness attenuation and chemical composition distributions are the obvious objectives of this characterization program. However, it also provides an opportunity to examine the inservice degradation and its comparison with currently available models for prediction of radiation embrittlement of RPV steels. All of these efforts will provide a better understanding of materials degradation and other issues associated with extending the lifetime of existing NPPs beyond 60 years of service. The primary foci are the Linde 80 flux, wire heat 72105 (WF-70) circumferential belt-line weld and the A533B-1 base metal from the intermediate shell harvested from a region of peak fluence (0.7 x 10{sup 19} n/cm{sup 2}, E > 1.0 MeV) on the internal surface of the Zion Unit 1 vessel. Following determination of the through-thickness chemical composition, Charpy impact, fracture toughness, tensile, and hardness testing will be being performed to characterize the through-thickness mechanical properties of the base metal and belt-line-weld materials. In addition to mechanical properties, microstructural characterizations will be performed using various techniques, including Atom Probe Tomography, Small Angle Neutron Scattering, and Positron Annihilation Spectroscopy.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Use of Neutron Flux Calculated by Shift in a Grizzly Reactor Pressure Vessel Fracture Simulation

The reactor pressure vessel (RPV) plays the critical role of containing the reactor and coolant in a light water reactor nuclear power plant, and must be able to safely perform this function under a variety of normal and off-normal transient loading conditions. The RPV is subjected to harsh environmental conditions (elevated temperature and high neutron flux) whenever the plant is operating, which leads to embrittlement of the steel over time. RPVs contain populations of flaws introduced during the manufacturing process, and the primary safety concern is that during a transient event, a fracture could initiate at the site of one of these flaws and lead to rupture of the RPV. RPVs are very rugged structures, and the probability of this occurring is very low, but as the RPV's steel becomes embrittled over time, its resistance to fracture decreases and this becomes more likely. Assessing the likelihood of RPV fracture during a transient event involves performing a probabilistic fracture mechanics analysis, in which random sampling procedures are used to assess the probability of fracture of a population of flaws. Grizzly offers unique capabilities for modeling the RPV using 1D, 2D, or 3D representations, taking advantage of parallel computing for this type of analysis. One of the important inputs to Grizzly is the spatial distribution of the neutron fluence, which has a large impact on the material embrittlement, and should thus be characterized as accurately as possible. The VERA core simulator developed by the CASL program takes advantage of high performance computing resources to perform high-fidelity multiphysics simulations of reactor physics, including the effects of neutron transport, fuel performance, and thermal hydraulics. Recently a capability was developed to also evaluate neutron fluxes away from the reactor core through the Shift code. This allows for a detailed 3D map of the spatial variation of the fluence in components such as the RPV to be computed, which is ideal for use with Grizzly. This report documents a procedure developed to use the fluences computed in Shift in a Grizzly simulation, which allows for improved realisim in the prediction of the effects of environmental exposure on propensity for reactor pressure vessel fracture. This capability demonstrated on RPVs with multiple types of configurations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Testing of Full Scale Flight Qualified Kevlar Composite Overwrapped Pressure Vessels

Many decades ago NASA identified a need for low-mass pressure vessels for carrying various fluids aboard rockets, spacecraft, and satellites. A pressure vessel design known as the composite overwrapped pressure vessel (COPV) was identified to provide a weight savings over traditional single-material pressure vessels typically made of metal and this technology has been in use for space flight applications since the 1970's. A typical vessel design consisted of a thin liner material, typically a metal, overwrapped with a continuous fiber yarn impregnated with epoxy. Most designs were such that the overwrapped fiber would carry a majority of load at normal operating pressures. The weight advantage for a COPV versus a traditional singlematerial pressure vessel contributed to widespread use of COPVs by NASA, the military, and industry. This technology is currently used for personal breathing supply storage, fuel storage for auto and mass transport vehicles and for various space flight and aircraft applications. The NASA Engineering and Safety Center (NESC) was recently asked to review the operation of Kevlar 2 and carbon COPVs to ensure they are safely operated on NASA space flight vehicles. A request was made to evaluate the life remaining on the Kevlar COPVs used on the Space Shuttle for helium and nitrogen storage. This paper provides a review of Kevlar COPV testing relevant to the NESC assessment. Also discussed are some key findings, observations, and recommendations that may be applicable to the COPV user community. Questions raised during the investigations have revealed the need for testing to better understand the stress rupture life and age life of COPVs. The focus of this paper is to describe burst testing of Kevlar COPVs that has been completed as a part of an the effort to evaluate the effects of ageing and shelf life on full scale COPVs. The test articles evaluated in this discussion had a diameter of 22 inches for S/N 014 and 40 inches for S/N 011. The time between manufacture and burst was 28 and 22 years. Visual inspection, shearography, heat soak thermography and borescope inspection were performed on vessel S/N 011 and all but shearography was performed on S/N 014 before they were tested and details of this work can be found in a companion paper titled, "Nondestructive Methods and Special Test Instrumentation Supporting NASA Composite Overwrapped Pressure Vessel Assessments." The vessels were instrumented so that measurements could be made to aid in the understanding of vessel response. Measurements made on the test articles included girth, boss displacement, internal volume, multiple point strain, full field strain, eddy current, acoustic emission (AE) pressure and temperature. The test article before and during burst is shown with the pattern used for digital image correlation full field strain measurement blurring as the vessel fails.

Greene, Nathanael↗