Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “POLYESTER RESIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Evaluation of Composite Materials for Use on Launch Complexes

Commercially available composite structural shapes were evaluated for use. These composites, fiberglass-reinforced polyester and vinylester resin materials are being used extensively in the fabrication and construction of low maintenance, corrosion resistant structures. The evaluation found that in many applications these composite materials can be successfully used at the space center. These composite materials should not be used where they will be exposed to the hot exhaust plume/cloud of the launch vehicle during the liftoff, and caution should be taken in their use in areas where electrostatic discharge and hypergolic propellant compatibility are primary concerns.

Finchum, A.↗
NASA NTRS1979

Silicone modified resins for graphite fiber laminates

The development of silicon modified resins for graphite fiber laminates which will prevent the dispersal of graphite fibers when the composites are burned is discussed. Eighty-five silicone modified resins were synthesized and evaluated including unsaturated polyesters, thermosetting methacrylates, epoxies, polyimides, and phenolics. Neat resins were judged in terms of Si content, homogeneity, hardness, Char formation, and thermal stability. Char formation was estimated by thermogravimetry to 1,000 C in air and in N2. Thermal stability was evaluated by isothermal weight loss measurements for 200 hrs in air at three temperatures. Four silicone modified epoxies were selected for evaluation in unidirectional filament wound graphite laminates. Neat samples of these resins had 1,000 C char residues of 25 to 50%. The highest flexural values measured for the laminates were a strength of 140 kpsi and a modulus of 10 Mpsi. The highest interlaminar shear strength was 5.3 kpsi.

Frost, L. W.↗
NASA NTRS1973

Shuttle active thermal control system development testing. Volume 7: Improved radiator coating adhesive tests

Silver/Teflon thermal control coatings have been tested on a modular radiator system projected for use on the space shuttle. Seven candidate adhesives have been evaluated in a thermal vacuum test on radiator panels similar to the anticipated flight hardware configuration. Several classes of adhesives based on polyester, silicone, and urethane resin systems were tested. These included contact adhesives, heat cured adhesives, heat and pressure cured adhesives, pressure sensitive adhesives, and two part paint on or spray on adhesives. The coatings attached with four of the adhesives, two silicones and two urethanes, had no changes develop during the thermal vacuum test. The two silicone adhesives, both of which were applied to the silver/Teflon as transfer laminates to form a tape, offered the most promise based on application process and thermal performance. Each of the successful silicone adhesives required a heat and pressure cure to adhere during the cryogenic temperature excursion of the thermal-vacuum test.

Reed, M. W.↗
NASA NTRS1976

Silver-Teflon coating improvement

Approximately forty adhesives were subjected to laboratory screening. Seven candidate adhesives were selected from the screening tests and evaluated in a thermal vacuum test on radiator panels similar to the anticipated flight hardware configuration. Several classes of adhesives based on epoxide, polyester, silicone, and urethane resin systems were tested. These included contact adhesives, heat cured adhesives, heat and pressure cured adhesives, pressure sensitive adhesives, and two part paint-on or spray-on adhesives. The panels were tested in a space environmental simulation laboratory chamber during the July 9-20, 1973 time span.

Reed, M. W.↗
NASA NTRS1979

Development of ultraviolet rigidizable materials

A series of tests was performed to determine an optimum resin to be used as a UV rigidizable matrix in expandable rigidizable space structures. Commercially available resins including several types of polyesters, epoxies, epoxy-acrylics, an acrylic and a urethane were used as well as a polyester, produced by 3M Company's Solar Laboratory facility, which was found the best from the standpoint of physical properties and ability to be 'B' staged. Two other synthesized materials were also tested, but were not found to be superior to the Solar resin. An optimum fabric for use with the preferred resin was not found; however, the 15 ounce fabric from Solar Laboratories has the best combination of physical properties with respect to handling and processing characteristics. Expansion techniques for tubular structures, 'B' staging of the solar resin, and stowage techniques for up to 5 months were developed. A one meter high tetrahedron preprototype structure was prepared to evaluate and demonstrate stowage, deployment, and rigidization techniques.

Salisbury, D. P.↗
NASA NTRS1967

Multi-feed cone for Cassegrainian antenna

Study of epoxies and polyesters determines which type of resin would satisfy the desirable prerequisites of a metallographic mount. Investigated were Polylite 8063, Polylite 8173, PE-169, and PE-228. The results were compared to the standard thermosetting mounting material, Bakelite, and found to be favorable.

Hughes, J.↗
NASA NTRS2003

Alabama NASA EPSCoR Preparation Grant Program: Grant No. NCC5-391

The funded research projects under the Experimental Program to Stimulate Cooperative Research (EPSCoR) grant program and the student fellowship awards are summarized in this report. The projects include: 1) Crystallization of Dehydratase/DcoH: A Target in Lung Disease; 2) Measuring Velocity Profiles in Liquid Metals using an Ultrasonic Doppler Velocimeter; 3) Synthesis, Structure, and Properties of New Thermoelectric Materials; 4) Computational Determination of Structures and Reactivity of Phenol-Formaldehyde Resins; 5) Synthesis of Microbial Polyesters in the NASA Bioreactor; 6) Visualization of Flow-Fields in Magnetocombustion; 7) Synthesis of Fluorescent Saccharide Derivatives. The student fellowship awards include: 1) Distributed Fusion of Satellite Images; 2) Study of the Relationship between Urban Development, Local Climate, and Water Quality for the Atlanta, Georgia Metrop; 3) Computer Simulation of the Effectiveness of a Spring-Loaded Exercise Device.

Gregory, John C.↗
NASA NTRS1987

Comparison of flexural properties of aramid-reinforced pultrusions having varied matrices, pretreatments and postcures

Aramid-reinforced composite materials of equal fiber volume and varied polymer thermoset matrices were pultruded and flexurally tested to failure. The objective was to improve the flexural properties of aramid-reinforced pultrusions. Pultrusions of both sized and unsized aramid fiber with four different resin systems were compared to determine the effects of sizing compounds and postcuring on flexural strength, fiber wettability, and fiber-to-resin interface bonding. Improvements in flexural strength resulting from pretreatments with the sizing solutions used were marginal. The most significant improvements in flexural properties resulted from postcuring. Flexural strengths ranged from a low of 39,647 psi (273MPa) to a high of 80,390 psi (554 MPa), an overall increase of 103 percent. The fact that postcuring improved the flexural properties of the pultrusions of the four resin systems indicates that a full cure did not occur in any of the resin systems during the pultrusion process. The increased flexural strengths of the polyester and vinyl ester pultrusions were the most surprising. The four resin systems examined were Interplastic Corporation VE 8300 vinyl ester, Ashland Chemical Company Aropol 7430 Polyester, and Shell Chemical Company Epon 9302 and Epon 9310 epoxides.

Wilson, Maywood L.↗
NASA NTRS1986

A comparison of flexural properties of aramid reinforced pultrusions having constant fiber volume and varied matrices, pretreatments, and postcures

Aramid reinforcement composite materials of equal fiber volume having varied polymer thermoset matrices have been pultruded and flexurally tested to failure. The objective was to improve flexural properties of aramid reinforced pultrusions. Pultrusions of both sized and unsized aramid fiber with four different resin systems were compared to determine the effects of sizing compounds and post-thermal treatments on the flexural strength as an indication of fiber wettability and fiber-to-resin interface bonding. Improvements in flexural strength as the result of pretreatments with sizing solutions used in this study were marginal. The most significant improvements in flexural properties were the results of postcuring. Overall improvements ranged from a low 39,647 Psi(273 Mpa) to a high of 80,390 Psi(554 Mpa), or 103 percent. The fact that post-thermal treatments improved the flexural properties of the four pultrusions indicates that a full cure did not occur in either resin system during the pultrusion process. The increased flexural strengths of the polyester and vinyl ester pultrusions were the most surprising. Based on data presented, the most promising resin system of the four examined (VE 8300, Aropol 7430, Epon 9302, and Epon 9310) for Kevlar reinforced pultrusion is Epon 9310 epoxy.

Wilson, Maywood L.↗
DOE OSTI2026

Aqueous ionic liquid–mediated depolymerization of textile waste

Textile waste, dominated by polyester-cotton blends, largely evades recycling and ends up in landfills or incinerators. Here, we demonstrate an aqueous ionic liquid–mediated route for selective depolymerization of textile waste, including polyester and polycotton (polyester/cotton blend). Using aqueous cholinium lysinate ([Ch][Lys]), we depolymerized poly(ethylene terephthalate) (PET) textiles with over 95 % terephthalic acid (TPA) yields, comparable to virgin PET resin. Notably, colored fabrics showed no inhibitory effect from dyes. While protic ionic liquids such as ethanolammonium acetate showed limited efficiency, their precursor amine enabled near-complete PET conversion—ethanolamine promoted aminolysis with byproduct formation whereas butylamine achieved higher TPA recovery through combined hydrolysis and aminolysis. Importantly, polycotton blends achieved complete PET depolymerization with TPA yield above 85 % and preserved cotton. These results establish aqueous ionic liquids as efficient, selective agents for deconstructing polyester in blended textiles, offering flexible product and ionic liquid management pathways toward scalable and facile textile recycling.

Amines↗
DOE OSTI2024

Manufacture and testing of biomass-derivable thermosets for wind blade recycling

Wind energy is helping to decarbonize the electrical grid, but wind blades are not recyclable, and current end-of-life management strategies are not sustainable. Here, to address the material recyclability challenges in sustainable energy infrastructure, we introduce scalable biomass-derivable polyester covalent adaptable networks and corresponding fiber-reinforced composites for recyclable wind blade fabrication. Through experimental and computational studies, including vacuum-assisted resin-transfer molding of a 9-meter wind blade prototype, we demonstrate drop-in technological readiness of this material with existing manufacture techniques, superior properties relative to incumbent materials, and practical end-of-life chemical recyclability. Most notable is the counterintuitive creep suppression, outperforming industry state-of-the-art thermosets despite the dynamic cross-link topology. Overall, this report details the many facets of wind blade manufacture, encompassing chemistry, engineering, safety, mechanical analyses, weathering, and chemical recyclability, enabling a realistic path toward biomass-derivable, recyclable wind blades.

17 WIND ENERGY↗
NASA NTRS1990

Intact capture of hypervelocity projectiles

The ability to capture projectiles intact at hypervelocities opens new applications in science and technology that would either not be possible or would be very costly by other means. This capability has been demonstrated in the laboratory for aluminum projectiles of 1.6 mm diameter, captured at 6 km/s, in one unmelted piece, and retaining up to 95% of the original mass. Furthermore, capture was accomplished passively using microcellular underdense polymer foam. Another advantage of capturing projectiles in an underdense medium is the ability of such a medium to preserve a record of the projectile's original velocity components of speed and direction. A survey of these experimental results is described in terms of a dozen parameters which characterize the amount of capture and the effect on the projectile due to different capture media.

NASA Discipline Number 52-50↗
NASA NTRS1982

Flexible composite film for printed circuit board

A flexible printed circuit for a printed circuit board in which layers of reaction product composed of a combination of phenoxy resin - polyisocyanate - brominated epoxy resin, and in which the equivalent ratio of those functional groups is hydroxyl group: isocyanate group: epoxy group - 1 : 0.2 to 2 : 0.5 to 3 are laminated on at least one side of saturated polyester film is discussed.

Yabe, K.↗
DOE OSTI2026

Latent Catalysis as a Platform for Accessing Diverse Material Properties in Vat Photopolymerization 3D Printing

Vat photopolymerization (VP) 3D printing is an attractive strategy to manufacture customized polymer parts. The properties of printed materials are limited by the need to employ a low viscosity liquid resin and achieve rapid polymerization kinetics. To circumvent this limitation, dual‐cure methods have been developed using reagents embedded in the liquid resin formulation; however, the reagent‐based approach requires the discovery and optimization of new chemistry for each desired material. Here, in this work, we demonstrate a catalytic, dual‐cure platform that enables access to both Nylon‐6 and polyester interpenetrating networks through VP 3D printing under a universal approach. Structure–reactivity relationships of the latent NHC catalysts led to the identification of a magnesium chloride–NHC adduct as a latent catalyst that is orthogonal to radical polymerization and can be unmasked at elevated temperatures post‐printing to initiate ring‐opening polymerization of lactones and lactams. This strategy results in access to semicrystalline materials, which are a challenging morphology to access via VP 3D printing, that have attractive mechanical properties and can be printed at high resolution. This work represents the first photochemical‐based 3D printing of Nylon‐based materials and demonstrates the value of catalytic approaches to access new material properties in VP 3D printing.

Colliver, Cali N. [University of North Carolina, C↗
NASA NTRS1987

Optimal cure cycle design of a resin-fiber composite laminate

A unified computed aided design method was studied for the cure cycle design that incorporates an optimal design technique with the analytical model of a composite cure process. The preliminary results of using this proposed method for optimal cure cycle design are reported and discussed. The cure process of interest is the compression molding of a polyester which is described by a diffusion reaction system. The finite element method is employed to convert the initial boundary value problem into a set of first order differential equations which are solved simultaneously by the DE program. The equations for thermal design sensitivities are derived by using the direct differentiation method and are solved by the DE program. A recursive quadratic programming algorithm with an active set strategy called a linearization method is used to optimally design the cure cycle, subjected to the given design performance requirements. The difficulty of casting the cure cycle design process into a proper mathematical form is recognized. Various optimal design problems are formulated to address theses aspects. The optimal solutions of these formulations are compared and discussed.

Hou, Jean W.↗
NASA NTRS1972

Nondestructive determination of fatigue crack damage in composites using vibration tests.

The vibration response of glass reinforced epoxy and polyester laminates was investigated. The complex modulus and the damping capacity were measured as fatigue crack damage accumulated. Changes in the Young's modulus as well as the damping capacity correlated with the amount of crack damage. The damping was especially sensitive to debonding of the reinforcement from the resin matrix. Measurement of these vibration response changes shows promise as a means to nondestructively test the structural integrity of filament-reinforced composite structural members.

Dibenedetto, A. T.↗
NASA NTRS1987

Optimal cure cycle design of a resin-fiber composite laminate

Fibers reinforced composites are used in many applications. The composite parts and structures are often manufactured by curing the prepreg or unmolded material. The magnitudes and durations of the cure temperature and the cure pressure applied during the cure process have significant consequences on the performance of the finished product. The goal of this study is to exploit the potential of applying the optimization technique to the cure cycle design. The press molding process of a polyester is used as an example. Various optimization formulations for the cure cycle design are investigated. Recommendations are given for further research in computerizing the cure cycle design.

Hou, Jean W.↗