Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Local homogeneity of cell cycle length in developing mouse cortex

We have measured the amount of variation in the length of the cell cycle for cells in the pseudostratified ventricular epithelium (PVE) of the developing cortex of mice on embryonic day 14. Our measurements were made in three cortical regions (i.e., the neocortex, archicortex, and periarchicortex) using three different methods: the cumulative labeling method (CLM), the percent labeled mitoses (PLM) method, and a comparison of the time needed for the PLM to ascend from 0 to 100% with the time needed for the PLM to descend from 100 to 0%. These 3 different techniques provide different perspectives on the cytokinetic parameters. Theoretically, CLM gives an estimate for a maximum value of the total length of the cell cycle (TC), whereas PLM gives an estimate of a minimum value of TC. The difference between these two estimates indicates that the range for TC is +/-1% of the mean TC for periarchicortex, +/-7% for neocortex, and +/-8% for archicortex. This was confirmed by a lengthening of the PLM descent time in comparison with its ascent time. The sharpness of the transitions and the flatness of the plateau of the PLM curves indicate that 99% of the proliferating cells are within this narrow estimated range for TC; hence, only approximately 1% deviate outside of a relatively restricted range from the average TC of the population. In the context of the possible existence within the cortical PVE of two populations with markedly dissimilar cell cycle kinetics from the mean, one such population must comprise approximately 99% of the total population, and the other, if it exists, is only approximately 1% of the total. This seems to be true for all three cortical regions. The narrow range of TC indicates a homogeneity in the cell cycle length for proliferating cells in three different cortical regions, despite the fact that progenitor cells of different lineages may be present. It further predicts the existence of almost synchronous interkinetic nuclear movements of the proliferating cells in the ventricular zone during early development of the cerebral cortex.

Non-NASA Center↗
NASA NTRS2010

Product Lifecycle Management and the Quest for Sustainable Space Explorations

Product Lifecycle Management (PLM) is an outcome of lean thinking to eliminate waste and increase productivity. PLM is inextricably tied to the systems engineering business philosophy, coupled with a methodology by which personnel, processes and practices, and information technology combine to form an architecture platform for product design, development, manufacturing, operations, and decommissioning. In this model, which is being implemented by the Engineering Directorate at the National Aeronautics and Space Administration's (NASA's) Marshall Space Flight Center, total lifecycle costs are important variables for critical decision-making. With the ultimate goal to deliver quality products that meet or exceed requirements on time and within budget, PLM is a powerful concept to shape everything from engineering trade studies and testing goals, to integrated vehicle operations and retirement scenarios. This paper will demonstrate how the Engineering Directorate is implementing PLM as part of an overall strategy to deliver safe, reliable, and affordable space exploration solutions. It has been 30 years since the United States fielded the Space Shuttle. The next generation space transportation system requires a paradigm shift such that digital tools and knowledge management, which are central elements of PLM, are used consistently to maximum effect. The outcome is a better use of scarce resources, along with more focus on stakeholder and customer requirements, as a new portfolio of enabling tools becomes second nature to the workforce. This paper will use the design and manufacturing processes, which have transitioned to digital-based activities, to show how PLM supports the comprehensive systems engineering and integration function. It also will go through a launch countdown scenario where an anomaly is detected to show how the virtual vehicle created from paperless processes will help solve technical challenges and improve the likelihood of launching on schedule, with less hands-on labor needed for processing and troubleshooting.

Caruso, Pamela W.↗
DOE OSTI2021

A Commercial Building Plug Load Management System that Uses Internet of Things Technology to Automatically Identify Plugged-In Devices and Their Locations

Plug and process loads (PPLs) account for a large portion of U.S. commercial building energy use. There is a huge potential to reduce whole building consumption by targeting PPLs for energy savings measures or implementing some form of plug load management (PLM). Despite this potential, there has yet to be a widely adopted commercial PLM technology. This paper describes the Automatic Type and Location Identification System (ATLIS), a PLM system framework with automatic and dynamic load detection (ADLD). ADLD gives PLM systems the ability to automatically identify devices as they are plugged into the outlets of a building. The ATLIS framework takes advantage of smart, connected devices to identify device locations in a building, meter and control their power, and communicate this information to a central database. ATLIS includes five primary capabilities: location identification, communication, control, energy metering, and data storage. A laboratory proof of concept (PoC) demonstrated all but the energy metering capability, and these capabilities were validated using a series of system tests. The PoC was able to identify when a device was plugged into an outlet and the location of the device in the building. When a device was moved, the PoC's dashboard and database were automatically updated with the new location. The PoC implemented controls to devices from the system dashboard so that devices maintained correct schedules regardless of where they were plugged in within the building. ATLIS's primary technology application is improved PLM, but other applications include asset management, energy audits, and interoperability for grid-interactive efficient buildings. An ATLIS-based system could also be used to direct power to critical devices, such as ventilators, during a brownout or blackout. Such a framework is an opportunity to make PLM more widespread and reduce the amount of energy consumed by PPLs in current and future commercial buildings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Electrical Analysis of Pulsed Laser Annealed Poly-Si:Ga/SiOx Passivating Contacts

High-efficiency single crystalline silicon (c-Si) solar cells require precise control of dopant diffusion profiles and highly active doping concentrations through thermal annealing. Conventional furnace annealing has been successfully employed for dopant diffusion in aluminum back-surface field (Al-BSF), passivated emitter and rear contact (PERC), and Topcon cells. However, furnace annealing limits some next-generation polycrystalline silicon (poly-Si) on SiOx passivating contacts. This limitation largely affects p-type passivating contacts by not being able to: 1) control the dopant diffusion accurately to prevent B segregation at the SiOx and c-Si interface; and 2) provide highly activated doping concentrations for low contact resistivity. In this contribution, we use a nanosecond excimer laser to examine the passivation quality and electrical performance of both B- and Ga-doped poly-Si/SiOx passivating contacts. The core of this method is to take advantage of the nonequilibrium nature of the anneal through rapid melting and recrystallizing the poly-Si in a short timescale and to achieve doping concentrations above the solid solubility limit. Simulations were performed on polished surfaces to visualize the doping diffusion profiles under different laser conditions, and secondary ion mass spectrometry (SIMS) was used to verify the experimental diffusion profiles post pulsed laser melting (PLM). The results show the dopant diffusion profiles can be tuned precisely through PLM. The electrical analysis using VdP-Hall measurements reveals that the active doping concentration reached 10^21 cm-3 for B and ~2×10^21 cm-3 for Ga in poly-Si, far exceeding their solid solubility limit in Si, with a nearly 100% dopant activation achieved for B, and 20% for Ga. This highly activated dopant profile results in a low contact resistivity of <15 mO·cm^2 for B-doped contacts and <40 mO·cm^2 for Ga-doped contacts. We demonstrate that the passivation quality of the laser annealed contacts shows a linear dependency with the laser energy density and the number of pulses. PLM was also performed on random pyramid textured samples, and we found that preferential melting exists for the tips of pyramids, which can be pursued further for selective pinhole opening. Additionally, we perform thermal stability tests of these hyperdoped passivating contacts and show that under certain laser conditions, the B-doped samples exhibit good thermal stability with near full activation for temperatures up to 800°C. Lastly, we transfer this technique to a larger area by overlapping laser spots and show uniform passivation quality and electrical performance. We are currently implementing this PLM annealed p-type passivating contacts into double-side back-junction poly-Si/SiOx passivating contact devices. Our results show that PLM can not only enable the next generation of high-efficiency c-Si photovoltaics technology but can also benefit the c-Si integrated circuit industry through hyperdoping other semiconductors with atoms that may otherwise have a low solubility.

doping diffusion profile↗
NASA NTRS2016

Polarized Light Microscopy

Polarized light microscopy (PLM) is a technique which employs the use of polarizing filters to obtain substantial optical property information about the material which is being observed. This information can be combined with other microscopy techniques to confirm or elucidate the identity of an unknown material, determine whether a particular contaminant is present (as with asbestos analysis), or to provide important information that can be used to refine a manufacturing or chemical process. PLM was the major microscopy technique in use for identification of materials for nearly a century since its introduction in 1834 by William Fox Talbot, as other techniques such as SEM (Scanning Electron Microscopy), FTIR (Fourier Transform Infrared spectroscopy), XPD (X-ray Powder Diffraction), and TEM (Transmission Electron Microscopy) had not yet been developed. Today, it is still the only technique approved by the Environmental Protection Agency (EPA) for asbestos analysis, and is often the technique first applied for identification of unknown materials. PLM uses different configurations in order to determine different material properties. With each configuration additional clues can be gathered, leading to a conclusion of material identity. With no polarizing filter, the microscope can be used just as a stereo optical microscope, and view qualities such as morphology, size, and number of phases. With a single polarizing filter (single polars), additional properties can be established, such as pleochroism, individual refractive indices, and dispersion staining. With two polarizing filters (crossed polars), even more can be deduced: isotropy vs. anisotropy, extinction angle, birefringence/degree of birefringence, sign of elongation, and anomalous polarization colors, among others. With the use of PLM many of these properties can be determined in a matter of seconds, even for those who are not highly trained. McCrone, a leader in the field of polarized light microscopy, often advised, If you cant determine a specific optical property of a particle after two minutes, move onto another configuration. Since optical properties can be seen so very quickly and easily under polarized light, it is only necessary to spend a maximum of two minutes on a technique to determine a particular property, though often only a few seconds are required.

Engineering↗
DOE OSTI2018

Plug Load Management System Field Study: Wireless Meter and Controls

This presentation offers background on GSA's Green Proving Ground (GPG) and DOE's High Impact Technology (HIT) Catalyst work, and a field study that assessed a plug load management (PLM) system in two commercial building applications. The Ibis InteliNetwork (TM) PLM system enables users to measure and analyze device energy use and identify opportunities for reduction of plug load energy use, and set times for individual devices (or groups of devices) to turn off when not in use. The presentation gives an overview of the PLM demonstration project, its results, and lessons learned.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2018

Crystal c-axis mapping of hcp metals by conventional reflected polarized light microscopy: Application to untextured and textured cp-Titanium

Highlights: • A computer-aided methodology based on reflected PLM was developed for c-axis orientation mapping of hcp structures. • The methodology was applied to two alpha cp-Ti bulk samples with different texture characteristics. • Calibration and validation of the methodology were performed by using EBSD. - Abstract: Nowadays the crystallographic characterization of polycrystalline metals and metallic alloys is usually performed by means of the electron backscatter diffraction (EBSD) technique. However, when dealing with coarse structures presenting intrinsic optical anisotropy, polarized light microscopy (PLM) imaging might be an alternative or a complementary time-efficient technique. Accordingly, a new computer-aided methodology has been developed in the present study and successfully applied on the crystal c-axis characterization of a hexagonal close-packed (hcp) structure, alpha commercial pure-Titanium (cp-Ti). In this sense, the correlation between EBSD-based crystallographic parameters and PLM-based parameters under certain light microscope settings has been first established by direct comparison using a representative amount of random orientations. Finally, PLM-based c-axis mapping and subsequent c-axis texture plotting have been performed and validated with EBSD for untextured and textured cp-Ti.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Plug Load Management System Field Study

In 2018, NREL performed a demonstration of the IBIS InteliNetwork(TM) plug load management system, which includes: intelligent socket devices, which plug into existing electrical outlets and collect energy usage information; a gateway, which manages communication between the intelligent sockets and the PLM cloud service; and a PLM network, which is a cloud-based measurement and control network for the entire system. Two retail stores served as the field study sites. The PLM system was found to be effective at reducing plug load energy use, with a projected annual plug load reduction of 11% and 18% at the test locations. Retail staff reported that the hardware was easy to use, but no one used the online data management system, intended to analyze and control the hardware. This PLM solution shows promise as an effective means to monitor, control, and reduce plug load energy use, but the economics of the system need to be improved.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2016

Model-based optimal design of active cool thermal energy storage for maximal life-cycle cost saving from demand management in commercial buildings

This article provides a method in comprehensive evaluation of cost-saving potential of active cool thermal energy storage (CTES) integrated with HVAC system for demand management in non-residential building. The active storage is beneficial by shifting peak demand for peak load management (PLM) as well as providing longer duration and larger capacity of demand response (DR). In this research, a model-based optimal design method using genetic algorithm is developed to optimize the capacity of active CTES aiming for maximizing the life-cycle cost saving concerning capital cost associated with storage capacity as well as incentives from both fast DR and PLM. In the method, the active CTES operates under a fast DR control strategy during DR events while under the storage-priority operation mode to shift peak demand during normal days. The optimal storage capacities, maximum annual net cost saving and corresponding power reduction set-points during DR event are obtained by using the proposed optimal design method. Lastly, this research provides guidance in comprehensive evaluation of cost-saving potential of CTES integrated with HVAC system for building demand management including both fast DR and PLM.

25 ENERGY STORAGE↗
DOE OSTI2020

Unsaturated and Saturated Hydraulic Parameters of Soils at the East River Watershed, Colorado Calculated using the Pedotransfer Function Method.

The purpose of the data package is to present the results of calculations of the following unsaturated-saturated hydraulic parameters of soils of the East River Watershed, Colorado: fully saturated water content (Qs), residual saturation (Qr), van genuchten parameters alpha and n, field capacity (FC), and saturated hydraulic conductivity (Ks). Calculations were conducted for the following soil texture types: sandy_loam, loam, silty_clay_loam, clay_loam, silt loam; the particle size distribution included the percentage of sand, silt, clay, and the bulk density (BD) of soils. Calculations were conducted for the following areas- Lower_Subalpine (6 samples),- Lower_Montane_lower_hillslope (7 samples),- Floodplain_at_base_of_lower_montane_hillslope, (11 samples),- PLM-0 (10 samples),- PLM-1 (10 samples), and - PLM-3 (13 samples)Calculations were conducted using the Pedotransfer Function Method developed by Tóth et al. (2014) with the application of the code ”euptf” in Rstudio. The data are being summarized in the Excel file ”Unsaturated_Saturated_Hydraulic_Parameters_PTF_calculated_EASt_EIver.xls" including two worksheets:“full_data_EAST_RIVER” which includes (a) the input data used for calculations, the soil texture triangle, and the plots of the water retention curves and unsaturated hydraulic conductivity for several types of soil texture, and (b) the summary table with the averaged parameters for each area. The the texture triangle was plotted using the Rstudio "soiltexture." Microsoft Excel software is required to open the Excel file. The metadata and a list of references to the Rstudio libraries used for calculations and data visualization are giving in the Word Readme file.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Data From: "Warming and snow loss increase reliance on old groundwater in a Colorado River headwater"

This repository contains the data and code associated with the paper titled "Warming and snow loss increase reliance on old groundwater in a Colorado River headwater," published in Nature Geoscience, 2026. This study seeks to answer how various ages of groundwater interact with mountainous streamflow in mountainous headwaters such as the East River. It includes various model-data processing scripts, primarily for ParFlow-CLM analysis of simulated water years 2015-2021, and two numerical warming experiments (+2.5 and +4.0 degrees C), including run scripts, forcing scripts, and post-processing, as well as comparison to observation datasets, detailed below. This data requires the use of R (.r, .rmd), Python (.py), Jupyter Notebook or Jupyter Lab (.ipynb), ParFLOW-CLM, EcoSLIM. Further information on the use of all file formats mentioned below (e.g. .tff. .nc) are provided within the associated scripts and directory where the files are located. Contents & Usage ASO/: ​​Contains the bash and python scripts used to convert airborne snow observatory (ASO) data (ASO, 2023) in various data formats (georeferenced tiff file, NetCDF, UTM, and to latitude/longitude) then regrided to the ParFlow equivalent grid. Output data are in regrid_regll_data.zip and subsequently visualized and analyzed in plot_and_compare.py for Supplementary Figures A14 and A15. The wksht_ASO_comparison.xlsx spreadsheet is used to calculate the data for Supplementary Figure A16. EcoSLIM/: Contains the scripts and input files to run the EcoSLIM particle tracking simulations (/run_scripts) and the post-processing python script (/plot_scripts/eco_agedist_plots.ipynb). Jasechko et al./: Contains the jupyter notebook (Extract_Elevation.ipynb) to determine the outlet elevations of the 260 watersheds used in Jasechko et al. (2016), and the corresponding table, Table_S1_Watersheds_alt.csv. Used to create Supplementary Information Figure A2. PLM_Wells/: Contains the QA/QC-ed groundwater level time series of the PLM-1 and PLM-6 Monitoring Wells from Faybishenko et al. (2023), reformatted to water years used for Supplementary Figures A19 and and A20. ParFlow/: Contains the input files and run scripts to run ParFlow-CLM (/run_scripts), the python and tool command language (Tcl) scripts to create and distribute the ParFlow forcing simulation files (/forcing), and various scripts and intermediary files to analyze the model outputs (/post_process). SQUIRE/: Contains the processing scripts and intermediary files for the Surface QUantitatIve pRecipitation Estimation (SQUIRE) data (Grover, 2023) used to generate Supplementary Figure A18. USGS_Streamflow/: Contains the raw and gap-filled United States Geological Survey streamflow data (U.S. Geological Survey, 2026) used at the Almont station (site number 09112500). Gap-filling is performed in the R script with data from the Taylor station (site number 09110000). (/USGS_09112500_EAST_RIVER_AT_ALMONT_GAP_FILLED/code_almont_streamflow_gap_fill.Rmd). discharge/: Contains the gap-filled discharge data at the Watershed Function SFA East River pumphouse site (Newcomer et al., 2022) used to generate Supplementary Figure A13 and to compute hourly Nash-Sutcliffe model efficiency coefficients (NSE) in Table A4. snotel_and_flux_tower/: Contains the snow telemetry data (U.S. Department of Agriculture, 2024) from the Butte (site ID 380) and Schofield (site ID 737) stations, reformatted by water year, accessed with the snotelr R package. Used to create Supplementary Figure A17. Also contains the flux tower observational data (FluxTower_Pumphouse_ESS-DIVE.ET_only.h.txt) from Ryken et al. (2022) and sap flux transpiration data (MaxB_Transpiration_5Sites.daily_sums.h.txt) from Ryken (2021), used to create Supplementary Figures A22 and A23, respectively. Raw EcoSLIM model outputs are in excess of 24TB, and are stored on National Energy Research Scientific Computing Center (NERSC) and publicly available via the external link provided in the paper.

atmospheric warming↗
DOE OSTI2015

Product Lifecycle Management Architecture: A Model Based Systems Engineering Analysis

This report is an analysis of the Product Lifecycle Management (PLM) program. The analysis is centered on a need statement generated by a Nuclear Weapons (NW) customer. The need statement captured in this report creates an opportunity for the PLM to provide a robust service as a solution. Lifecycles for both the NW and PLM are analyzed using Model Based System Engineering (MBSE).

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Emerging Plug Load Management Technologies that Save Energy and Time

This fact sheet introduces two emerging technologies that could streamline plug load management (PLM) for increased energy savings for building owners: learning behavior algorithms (LBA) and automatic and dynamic load detection (ADLD). Plug loads are responsible for 47% of the energy consumed in commercial buildings, yet their distributed and ever-changing nature makes them challenging to manage. PLM systems exist today that use smart plugs to meter and control devices at the outlet level, but their uptake has been relatively slow in part because of the significant labor required for installation and maintenance. LBA and ADLD may address these challenges and provide additional energy efficiency and nonenergy benefits.

Plug and process loads, PPL, plug loads, plug load↗
DOE OSTI2023

Ferroelectric Domain Wall Engineering Enables Thermal Modulation in PMN–PT Single Crystals

Acting like thermal resistances, ferroelectric domain walls can be manipulated to realize dynamic modulation of thermal conductivity ( k ), which is essential for developing novel phononic circuits. Despite the interest, little attention has been paid to achieving room-temperature thermal modulation in bulk materials due to challenges in obtaining a high thermal conductivity switching ratio ( k high / k low ), particularly in commercially viable materials. Here, room-temperature thermal modulation in 2.5 mm-thick Pb(Mg 1/3 Nb 2/3 )O 3 – x PbTiO 3 (PMN– x PT) single crystals is demonstrated. With the use of advanced poling conditions, assisted by the systematic study on composition and orientation dependence of PMN– x PT, a range of thermal conductivity switching ratios with a maximum of ≈1.27 is observed. Further, simultaneous measurements of piezoelectric coefficient (d 33 ) to characterize the poling state, domain wall density using polarized light microscopy (PLM), and birefringence change using quantitative PLM reveal that compared to the unpoled state, the domain wall density at intermediate poling states (0< d 33 33,max ) is lower due to the enlargement in domain size. At optimized poling conditions (d 33,max ), the domain sizes show increased inhomogeneity that leads to enhancement in the domain wall density. This work highlights the potential of commercially available PMN– x PT single crystals among other relaxor-ferroelectrics for achieving temperature control in solid-state devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Pulsed Laser Annealed Ga Hyperdoped Poly‐Si / SiO x Passivating Contacts for High‐Efficiency Monocrystalline Si Solar Cells

Polycrystalline Si ( poly ‐Si)‐based passivating contacts are promising candidates for high‐efficiency crystalline Si solar cells. We show that nanosecond‐scale pulsed laser melting (PLM) is an industrially viable technique to fabricate such contacts with precisely controlled dopant concentration profiles that exceed the solid solubility limit. We demonstrate that conventionally doped, hole‐selective poly ‐Si/SiO x contacts that provide poor surface passivation of c ‐Si can be replaced with Ga‐ or B‐doped contacts based on non‐equilibrium doping. We overcome the solid solubility limit for both dopants in poly ‐Si by rapid cooling and recrystallization over a timescale of ∼25 ns. We show an active Ga dopant concentration of ∼3 × 10 20 cm −3 in poly ‐Si which is six times higher than its solubility limit in c ‐Si, and a B dopant concentration as high as ∼10 21 cm −3 . We measure an implied open‐circuit voltage of 735 mV for Ga‐doped poly ‐Si/SiO x contacts on Czochralski Si with a low contact resistivity of 35.5 ± 2.4 mΩ cm 2 . Scanning spreading resistance microscopy and Kelvin probe force microscopy show large diffusion and drift current in the p ‐ n junction that contributes to the low contact resistivity. Our results suggest that PLM can be extended for hyperdoping of other semiconductors with low solubility atoms to enable high‐efficiency devices.

14 SOLAR ENERGY↗
DOE OSTI2023

KEBLM: Knowledge-Enhanced Biomedical Language Models

Pretrained language models (PLMs) have demonstrated strong performance on many natural language processing (NLP) tasks. Despite their great success, these PLMs are typically pretrained only on unstructured free texts without leveraging existing structured knowledge bases that are readily available for many domains, especially scientific domains. As a result, these PLMs may not achieve satisfactory performance on knowledge-intensive tasks such as biomedical NLP. Comprehending a complex biomedical document without domain-specific knowledge is challenging, even for humans. Inspired by this observation, we propose a general framework for incorporating various types of domain knowledge from multiple sources into biomedical PLMs. We encode domain knowledge using lightweight adapter modules, bottleneck feed-forward networks that are inserted into different locations of a backbone PLM. For each knowledge source of interest, we pretrain an adapter module to capture the knowledge in a self-supervised way. We design a wide range of self-supervised objectives to accommodate diverse types of knowledge, ranging from entity relations to description sentences. Once a set of pretrained adapters is available, we employ fusion layers to combine the knowledge encoded within these adapters for downstream tasks. Each fusion layer is a parameterized mixer of the available trained adapters that can identify and activate the most useful adapters for a given input. Our method diverges from prior work by including a knowledge consolidation phase, during which we teach the fusion layers to effectively combine knowledge from both the original PLM and newly-acquired external knowledge using a large collection of unannotated texts. After the consolidation phase, the complete knowledge-enhanced model can be fine-tuned for any downstream task of interest to achieve optimal performance. Extensive experiments on many biomedical NLP datasets show that our proposed framework consistently improves the performance of the underlying PLMs on various downstream tasks such as natural language inference, question answering, and entity linking. These results demonstrate the benefits of using multiple sources of external knowledge to enhance PLMs and the effectiveness of the framework for incorporating knowledge into PLMs. Finally, while primarily focused on the biomedical domain in this work, our framework is highly adaptable and can be easily applied to other domains, such as the bioenergy sector.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
DOE OSTI2019

Sphingolipid biosynthesis modulates plasmodesmal ultrastructure and phloem unloading

During phloem unloading, multiple cell-to-cell transport events move organic substances to the root meristem. Although the primary unloading event from the sieve elements to the phloem pole pericycle has been characterized to some extent, little is known about post-sieve element unloading. Here, we report a novel gene, PHLOEM UNLOADING MODULATOR (PLM), in the absence of which plasmodesmata-mediated symplastic transport through the phloem pole pericycle-endodermis interface is specifically enhanced. Increased unloading is attributable to a defect in the formation of the endoplasmic reticulum-plasma membrane tethers during plasmodesmal morphogenesis, resulting in the majority of pores lacking a visible cytoplasmic sleeve. PLM encodes a putative enzyme required for the biosynthesis of sphingolipids with very-long-chain fatty acid. Taken together, our results indicate that post-sieve element unloading involves sphingolipid metabolism, which affects plasmodesmal ultrastructure. They also raise the question of how and why plasmodesmata with no cytoplasmic sleeve facilitate molecular trafficking.

Yan, Dawei (ORCID:0000000182560279)↗
DOE OSTI2013

Supersaturating silicon with transition metals by ion implantation and pulsed laser melting

We investigate the possibility of creating an intermediate band semiconductor by supersaturating Si with a range of transition metals (Au, Co, Cr, Cu, Fe, Pd, Pt, W, and Zn) using ion implantation followed by pulsed laser melting (PLM). Structural characterization shows evidence of either surface segregation or cellular breakdown in all transition metals investigated, preventing the formation of high supersaturations. However, concentration-depth profiling reveals that regions of Si supersaturated with Au and Zn are formed below the regions of cellular breakdown. Fits to the concentration-depth profile are used to estimate the diffusive speeds, v{sub D,} of Au and Zn, and put lower bounds on v{sub D} of the other metals ranging from 10{sup 2} to 10{sup 4} m/s. Knowledge of v{sub D} is used to tailor the irradiation conditions and synthesize single-crystal Si supersaturated with 10{sup 19} Au/cm{sup 3} without cellular breakdown. Values of v{sub D} are compared to those for other elements in Si. Two independent thermophysical properties, the solute diffusivity at the melting temperature, D{sub s}(T{sub m}), and the equilibrium partition coefficient, k{sub e}, are shown to simultaneously affect v{sub D}. We demonstrate a correlation between v{sub D} and the ratio D{sub s}(T{sub m})/k{sub e}{sup 0.67}, which is exhibited for Group III, IV, and V solutes but not for the transition metals investigated. Nevertheless, comparison with experimental results suggests that D{sub s}(T{sub m})/k{sub e}{sup 0.67} might serve as a metric for evaluating the potential to supersaturate Si with transition metals by PLM.

36 MATERIALS SCIENCE↗