Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PD Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Control-structure interaction in precision pointing servo loops

The control-structure interaction problem is addressed via stability analysis of a generic linear servo loop model. With the plant described by the rigid body mode and a single elastic mode, structural flexibility is categorized into one of three types: (1) appendage, (2) in-the-loop minimum phase, and (3) in-the-loop nonminimum phase. Closing the loop with proportional-derivative (PD) control action and introducing sensor roll-off dynamics in the feedback path, stability conditions are obtained. Trade studies are conducted with modal frequency, modal participation, modal damping, loop bandwidth, and sensor bandwidth treated as free parameters. Results indicate that appendage modes are most likely to produce instability if they are near the sensor rolloff, whereas in-the-loop modes are most dangerous near the loop bandwidth. The main goal of this paper is to provide a fundamental understanding of the control-structure interaction problem so that it may benefit the design of complex spacecraft and pointing system servo loops. In this framework, the JPL Pathfinder gimbal pointer is considered as an example.

Spanos, John T.↗
NASA NTRS2004

Space Shuttle Upgrades Advanced Hydraulic Power System

Three Auxiliary Power Units (APU) on the Space Shuttle Orbiter each provide 145 hp shaft power to a hydraulic pump which outputs 3000 psi hydraulic fluid to 41 hydraulic actuators. A hydrazine fuel powered APU utilized throughout the Shuttle program has undergone many improvements, but concerns remain with flight safety, operational cost, critical failure modes, and hydrazine related hazards. The advanced hydraulic power system (AHPS), also known as the electric APU, is being evaluated as an upgrade to replace the hydrazine APU. The AHPS replaces the high-speed turbine and hydrazine fuel supply system with a battery power supply and electric motor/pump that converts 300 volt electrical power to 3000 psi hydraulic power. AHPS upgrade benefits include elimination of toxic hydrazine propellant to improve flight safety, reduction in hazardous ground processing operations, and improved reliability. Development of this upgrade provides many interesting challenges and includes development of four hardware elements that comprise the AHPS system: Battery - The battery provides a high voltage supply of power using lithium ion cells. This is a large battery that must provide 28 kilowatt hours of energy over 99 minutes of operation at 300 volts with a peak power of 130 kilowatts for three seconds. High Voltage Power Distribution and Control (PD&C) - The PD&C distributes electric power from the battery to the EHDU. This 300 volt system includes wiring and components necessary to distribute power and provide fault current protection. Electro-Hydraulic Drive Unit (EHDU) - The EHDU converts electric input power to hydraulic output power. The EHDU must provide over 90 kilowatts of stable, output hydraulic power at 3000 psi with high efficiency and rapid response time. Cooling System - The cooling system provides thermal control of the Orbiter hydraulic fluid and EHDU electronic components. Symposium presentation will provide an overview of the AHPS upgrade, descriptions of the four hardware elements, and a summary of development results to date.

Source record↗
DOE OSTI2026

Colloidal Synthesis of Palladium Nanocluster‐Decorated Cs 3 Sb 2 Cl 9 Perovskite Heterostructural Nanorods for Enhanced CO 2 Photoreduction

Developing efficient and sustainable photocatalysts for CO 2 reduction remains a significant challenge, particularly with environmentally benign materials. Here, in this study, we report the first one-step synthesis of metal–lead-free perovskite heterostructural nanocrystals by decorating Cs 3 Sb 2 Cl 9 perovskite nanorods with size-controlled Pd nanoclusters via a one-step hot-injection method. The resulting Pd-Cs 3 Sb 2 Cl 9 heteronanorods (HNRs) exhibit strong interfacial electronic coupling, enhanced charge separation, and excellent colloidal stability. Transient absorption spectroscopy and DFT calculations reveal a built-in electric field that drives directional electron transfer from the perovskite host to the Pd domains. Under UV irradiation, the Pd-Cs 3 Sb 2 Cl 9 HNRs demonstrate excellent CO 2 photoreduction activity with high CH 4 selectivity, achieving a record apparent quantum yield (AQY) of 2.62% among halide perovskite nanocrystal-based systems with a large electronic yield of 689.3 ± 12.2 µmol·g cat −1 . In situ spectroscopic monitoring and Gibbs free energy analysis further unveil a Pd-facilitated reaction pathway involving stabilization of key intermediates. This work introduces a new class of lead-free perovskite-based heterostructures through a facile one-step synthesis strategy and offers a new design principle for next-generation photocatalysts for solar fuel production.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS2010

Experimental Methodology for Determining Turbomachinery Blade Damping Using Magnetic Bearing Excitation and Non-Contacting Optical Measurements

Experiments to determine the effects of turbomachinery fan blade damping concepts such as passively shunted piezoelectric materials on blade response are ongoing at the NASA Glenn Research Center. A vertical rotor is suspended and excited with active magnetic bearings (AMBs) usually in a vacuum chamber to eliminate aerodynamic forces. Electromagnetic rotor excitation is superimposed onto rotor PD-controlled support and can be fixed to either a stationary or rotating frame of reference. The rotor speed is controlled with an air turbine system. Blade vibrations are measured using optical probes as part of a Non-Contacting Stress Measurement System (NSMS). Damping is calculated from these measurements. It can be difficult to get accurate damping measurements using this experimental setup and some of the details of how to obtain quality results are seemingly nontrivial. The intent of this paper is to present those details.

Provenza, Andrew J.↗
NASA NTRS2015

Sun Safe Mode Controller Design for LADEE

This paper presents the development of sun safe controllers which are designed to keep the spacecraft power positive and thermally balanced in the event an anomaly is detected. Employed by NASA's Lunar Atmosphere and Dust Environment Explorer (LADEE), the controllers utilize the measured sun vector and the spacecraft body rates for feedback control. To improve the accuracy of sun vector estimation, the least square minimization approach is applied to process the sensor data, which is proven to be effective and accurate. To validate the controllers, the LADEE spacecraft model engaging the sun safe mode was first simulated and then compared with the actual LADEE orbital fight data. The results demonstrated the applicability of the proposed sun safe controllers.

Sun Safe Control↗
DOE OSTI2024

Dual blockade of IL-10 and PD-1 leads to control of SIV viral rebound following analytical treatment interruption

Human immunodeficiency virus (HIV) persistence during antiretroviral therapy (ART) is associated with heightened plasma interleukin-10 (IL-10) levels and PD-1 expression. We hypothesized that IL-10 and PD-1 blockade would lead to control of viral rebound following analytical treatment interruption (ATI). Twenty-eight ART-treated, simian immunodeficiency virus (SIV)mac 239 -infected rhesus macaques (RMs) were treated with anti-IL-10, anti-IL-10 plus anti-PD-1 (combo) or vehicle. ART was interrupted 12 weeks after introduction of immunotherapy. Durable control of viral rebound was observed in nine out of ten combo-treated RMs for >24 weeks post-ATI. Induction of inflammatory cytokines, proliferation of effector CD8 + T cells in lymph nodes and reduced expression of BCL-2 in CD4 + T cells pre-ATI predicted control of viral rebound. Twenty-four weeks post-ATI, lower viral load was associated with higher frequencies of memory T cells expressing TCF-1 and of SIV-specific CD4 + and CD8 + T cells in blood and lymph nodes of combo-treated RMs. These results map a path to achieve long-lasting control of HIV and/or SIV following discontinuation of ART.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1989

Direct adaptive control of a PUMA 560 industrial robot

The implementation and experimental validation of a new direct adaptive control scheme on a PUMA 560 industrial robot is described. The testbed facility consists of a Unimation PUMA 560 six-jointed robot and controller, and a DEC MicroVAX II computer which hosts the Robot Control C Library software. The control algorithm is implemented on the MicroVAX which acts as a digital controller for the PUMA robot, and the Unimation controller is effectively bypassed and used merely as an I/O device to interface the MicroVAX to the joint motors. The control algorithm for each robot joint consists of an auxiliary signal generated by a constant-gain Proportional plus Integral plus Derivative (PID) controller, and an adaptive position-velocity (PD) feedback controller with adjustable gains. The adaptive independent joint controllers compensate for the inter-joint couplings and achieve accurate trajectory tracking without the need for the complex dynamic model and parameter values of the robot. Extensive experimental results on PUMA joint control are presented to confirm the feasibility of the proposed scheme, in spite of strong interactions between joint motions. Experimental results validate the capabilities of the proposed control scheme. The control scheme is extremely simple and computationally very fast for concurrent processing with high sampling rates.

Seraji, Homayoun↗
NASA NTRS2006

A Bearingless Switched-Reluctance Motor for High Specific Power Applications

A 12-8 switched-reluctance motor (SRM) is studied in bearingless (or self-levitated) operation with coil currents limited to the linear region to avoid magnetic saturation. The required motoring and levitating currents are summed and go into a single motor coil per pole to obtain the highest power output of the motor by having more space for motor coil winding. Two controllers are investigated for the bearingless SRM operation. First, a model-based controller using the radial force, which is adjusted by a factor derived from finite element analysis, is presented. Then a simple and practical observation-based controller using a PD (proportional-derivative) control algorithm is presented. Both controllers were experimentally demonstrated to 6500 rpm. This paper reports the initial efforts toward eventual self levitation of a SRM operating into strong magnetic core saturation at liquid nitrogen temperature.

Choi, Benjamin B.↗
NASA NTRS1988

A control scheme for trajectory tracking of robot manipulators

The authors put forward a simple scheme for multivariable control of robot manipulators. The scheme is composed of an inner-loop stabilizing controller and an outerloop tracking controller. The inner loop utilizes a multivariable PD (proportional differential) controller to stabilize the robot by placing the poles at some desired locations. The outer loop uses a multivariable PID (proportional integral differential) controller to achieve input-output decoupling and trajectory tracking. The gains of the PD and PID controllers are related directly to the linearized robot model by simple closed-form expressions. The controller gains are updated online to cope with variations in the robot model for gross motion and payload change. Alternatively, the use of high-gain controllers for gross motion and payload change are discussed.

Tarokh, M.↗
NASA NTRS2002

Estimator Based Controller for High Speed Flywheel Magnetic Bearing System

A flywheel system and its operator interface are described. Measurements of magnetic bearing negative stiffness are performed. Two digital magnetic bearing control algorithms (PD and estimator based) are defined and their implementations are described. Tuning of each controller is discussed. Comparison of the two controllers' stability, damping noise, and operating current are described. Results describing the superiority of the estimator-based controller are presented and discussed.

Dever, Timothy P.↗
NASA NTRS1990

Learning-based position control of a closed-kinematic chain robot end-effector

A trajectory control scheme whose design is based on learning theory, for a six-degree-of-freedom (DOF) robot end-effector built to study robotic assembly of NASA hardwares in space is presented. The control scheme consists of two control systems: the feedback control system and the learning control system. The feedback control system is designed using the concept of linearization about a selected operating point, and the method of pole placement so that the closed-loop linearized system is stabilized. The learning control scheme consisting of PD-type learning controllers, provides additional inputs to improve the end-effector performance after each trial. Experimental studies performed on a 2 DOF end-effector built at CUA, for three tracking cases show that actual trajectories approach desired trajectories as the number of trials increases. The tracking errors are substantially reduced after only five trials.

Nguyen, Charles C.↗
DOE OSTI2025

Pd–Methyl Bond Energy─Property Correlations, Noncorrelations, Machine Learning Models, and Application to Polymerization Catalysis

Metal–carbon bonds are a key intermediate in a variety of homogeneous organometallic transformations and often determine the critical thermodynamics and kinetics of catalytic processes. Surprisingly, the influence of different ligands on metal–carbon bond strengths has been largely overlooked. Here, in this study, we evaluated nearly 700 experimental Pd–methyl complexes by calculating their bond dissociation energies using density functional theory (DFT) and compared these bond strengths to several fundamental molecular properties, and this revealed several surprising correlations and noncorrelations. Most surprising was that several fundamental properties, such as the bond length, bond force constant, and bond electron density, have no correlation with bond strength, despite these correlations often holding for main-group compounds. We were indeed able to identify key ligand-dependent chemical features/descriptors that provided a highly accurate machine learning model and provided insight into the general factors that control the Pd–carbon bond strength, such as radical delocalization and nucleophilicity. Insights gained from the Pd–Me bond energy analysis were then applied to CO migratory insertion steps that are part of copolymerization reactions.

binding energy↗
DOE OSTI2025

Mechanistic Insights into Adsorptive and Catalytic Reactions from Controllable Distributions of Metal Cations (Pd, Pt, Ni, Cr, Cu) as [M‐OH] +1 /1Al or M +2 /2Al in Zeolites

Anchoring divalent metal ions in the same zeolite framework with similar Si/Al ratio selectively as zeolite-bound M +2 or [M +2 -OH] +1 cationic species enables critical comparison of the species’ intrinsic reactivity for industrially and fundamentally relevant reactions. H-BEA zeolites with similar Si/Al ratios but differing framework Al siting were used to anchored multiple divalent metal cations (Ni, Pd, Pt, Cr, Cu) in the zeolite micropores. State-of-the-art infrared (IR) spectroscopy, electron paramagnetic resonance (EPR) measurements, including two-dimensional pulsed HYSCORE EPR, extended X-ray absorption fine structure (EXAFS), and density functional theory (DFT) calculations together provide unambiguous evidence for the selective formation of divalent metal cations as M +2 /2Al species (for H-BEA prepared in the conventional hydroxide media), and [M +2 OH] +1 /1Al species for H-BEA prepared in HF. Solid-state proton-decoupled triple-quantum magic-angle spinning (3Q MAS) NMR measurements confirmed contrasting Al distributions in the two H-BEA zeolites, which led to a contrasting divalent cation speciation. The reactivities of the two cationic species were explored for catalytic and adsorptive applications in both organometallic homogeneous and heterogeneous catalysis. This work demonstrates their divergent reactivity in ethylene dimerization, ethylene oxidation (Wacker process), selective catalytic reduction (SCR) of NO, NO adsorption, and methane oxidation. Both M +2 /2Al and [M +2 OH] +1 /1Al cations are both active for ethylene dimerization, but [M +2 OH] +1 /1Al species show higher reaction rates for each Pd, Ni, Pt. [M +2 OH] +1 /1Al is active for acetaldehyde formation in Wacker ethylene oxidation. A new active site for ethylene oligomerization is proposed that possesses a terminal OH group (Cr-OH) in Phillips catalysts evident by a nearly inactive isolated Cr +2 /2Al species that contrast an active Cr─OH motif.

Divalent metal cations in a zeolite↗
NASA NTRSDate not supplied

Automated Downlink Pipeline for Scientific Data Using TReK

ISS users generate scientific data files on orbit that require console operators to retrieve and deliver them for analysis. Automating the downlink process using TReK CFDP and DTN provides ground flight controllers and PD teams increased efficiency, reducing workload and resulting in cost savings without reduced services provided.

TReK↗
NASA NTRS2007

Robust Fuzzy Controllers Using FPGAs

Electro-mechanical device controllers typically come in one of three forms, proportional (P), Proportional Derivative (PD), and Proportional Integral Derivative (PID). Two methods of control are discussed in this paper; they are (1) the classical technique that requires an in-depth mathematical use of poles and zeros, and (2) the fuzzy logic (FL) technique that is similar to the way humans think and make decisions. FL controllers are used in multiple industries; examples include control engineering, computer vision, pattern recognition, statistics, and data analysis. Presented is a study on the development of a PD motor controller written in very high speed hardware description language (VHDL), and implemented in FL. Four distinct abstractions compose the FL controller, they are the fuzzifier, the rule-base, the fuzzy inference system (FIS), and the defuzzifier. FL is similar to, but different from, Boolean logic; where the output value may be equal to 0 or 1, but it could also be equal to any decimal value between them. This controller is unique because of its VHDL implementation, which uses integer mathematics. To compensate for VHDL's inability to synthesis floating point numbers, a scale factor equal to 10(sup (N/4) is utilized; where N is equal to data word size. The scaling factor shifts the decimal digits to the left of the decimal point for increased precision. PD controllers are ideal for use with servo motors, where position control is effective. This paper discusses control methods for motion-base platforms where a constant velocity equivalent to a spectral resolution of 0.25 cm(exp -1) is required; however, the control capability of this controller extends to various other platforms.

Monroe, Author Gene S., Jr.↗
DOE OSTI2026

Climatic imprint on interfacially-controlled platinum-palladium resources

Abstract Iron oxide-rich laterites, soils, and regolith formed from the weathering of ultramafic rocks represent untapped unconventional resources for the critical minerals platinum and palladium, but the fundamental surficial geochemistry of these elements remains poorly understood. Depletion of Pd relative to Pt occurs in some weathering zones in semi-arid climates. The accepted model attributes this platinum-palladium chemical fractionation to preferential complexation of Pd by dissolved chloride. However, similar fractionation is not observed in laterites of humid equatorial regions despite substantial wet deposition of chloride. The established mechanistic model for Pt and Pd behavior during weathering thus inaccurately predicts the distribution of these critical minerals in many settings, hindering global resource assessment. We show through mineral-fluid partitioning experiments coupled to element-specific spectroscopy that this canonical explanation for platinum-palladium fractionation is invalid: chloride complexation does not differentially mobilize Pd versus Pt. Instead, mineral-specific interfacial reactions control Pd and Pt accumulation. Modeling of platinum-palladium fractionation in representative weathering zone profiles demonstrates sub-equal retention in goethite-rich settings and Pd depletion in hematite-rich zones, accurately predicting trends observed in soils and laterites. Iron oxide mineralogy, reflecting modern and past regional climate conditions, is likely the primary determinant of Pt and Pd endowment in weathering zone resources. This new model for Pt and Pd mobilization and accumulation behavior provides a mechanistic foundation for exploration and recovery of platinum group elements from novel ultramafic regolith deposits.

58 GEOSCIENCES↗
NASA NTRS1993

Fuzzy control of small servo motors

To explore the benefits of fuzzy logic and understand the differences between the classical control methods and fuzzy control methods, the Togai InfraLogic applications engineering staff developed and implemented a motor control system for small servo motors. The motor assembly for testing the fuzzy and conventional controllers consist of servo motor RA13M and an encoder with a range of 4096 counts. An interface card was designed and fabricated to interface the motor assembly and encoder to an IBM PC. The fuzzy logic based motor controller was developed using the TILShell and Fuzzy C Development System on an IBM PC. A Proportional-Derivative (PD) type conventional controller was also developed and implemented in the IBM PC to compare the performance with the fuzzy controller. Test cases were defined to include step inputs of 90 and 180 degrees rotation, sine and square wave profiles in 5 to 20 hertz frequency range, as well as ramp inputs. In this paper we describe our approach to develop a fuzzy as well as PH controller, provide details of hardware set-up and test cases, and discuss the performance results. In comparison, the fuzzy logic based controller handles the non-linearities of the motor assembly very well and provides excellent control over a broad range of parameters. Fuzzy technology, as indicated by our results, possesses inherent adaptive features.

Maor, Ron↗