Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PCS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Into building fading at L- and S-band for satellite PCS

Selected results from L- and S-Band slant-path fade measurements into six different buildings employing a tower-mounted transmitter and dual-frequency receiver are presented. The objective of the measurements was to provide information for personal communications satellite design on the correlation of fading inside buildings between frequencies near 1620 and 2500 MHz. Fades were measured along horizontal directions with 5 cm spacing. Fade differences between L- and S-Band exhibited a normal distribution with means usually near 0 dB and standard deviations from 7.2 to 8.2 dB. After spatial averaging over a few wavelengths, the correlation between L- and S-Band was significantly improved. Simultaneous swept measurements over 160 MHz spans showed that the standard deviation of the power levels as function of frequency increased linearly with average fade depth from a minimum of about 1.3 dB and increased by .2 dB per 1 dB of fade. Fade slopes were also a function of fade level, with LMSS-Band averages in the range of 1 to 2 dB/MHz for 10 dB fades and increasing to about 3 to 4 dB/MHz at a 30 dB fade.

Vogel, Wolfhard J.↗
NASA NTRS1995

Measurement of satellite PCS fading using GPS

A six-channel commercial GPS receiver with a custom-made 40 deg tilted, rotating antenna has been assembled to make fade measurements for personal satellite communications. The system can measure up to two times per minute fades of up to 15 dB in the direction of each tracked satellite from 10 to 90 deg elevation. Photographic fisheye lens images were used to categorize the fade data obtained in several test locations according to fade states of clear, shadowed, or blocked. Multipath effects in the form of annular rings can be observed when most of the sky is clear. Tree fading by a Pecan exceeding 3.5 dB and 12 dB at 50 to 10 percent probability, respectively, compared with median fades of 7.5 dB measured earlier and the discrepancy is attributed to the change in ratio when measuring over an area as opposed to along a line. Data acquired inside buildings revealed 'rf-leaky' ceilings. Satellite diversity gain in a shadowed environment exceeded 6 dB at the 10 percent probability.

Vogel, Wolfhard J.↗
NASA NTRS2001

Physics of Colloids in Space (PCS) Flight Hardware Developed

investigation that will be located in an Expedite the Process of Experiments to Space Station (EXPRESS) Rack. The investigation will be conducted in the International Space Station U.S. laboratory, Destiny, over a period of approximately 10 months during the station assembly period from flight 6A through flight UF-2. This experiment will gather data on the basic physical properties of colloids by studying three different colloid systems with the objective of understanding how they grow and what structures they form. A colloidal suspension consists of fine particles (micrometer to submicrometer) suspended in a fluid for example, paints, milk, salad dressings, and aerosols. The long-term goal of this investigation is to learn how to steer the growth of colloidal suspensions to create new materials and new structures. This experiment is part of a two-stage investigation conceived by Professor David Weitz of Harvard University along with Professor Peter Pusey of the University of Edinburgh. The experiment hardware was developed by the NASA Glenn Research Center through contracts with Dynacs, Inc., and ZIN Technologies.

Koudelka, John M.↗
NASA NTRS2003

Physics of Colloids in Space (PCS): Microgravity Experiment Completed Operations on the International Space Station

Immediately after mixing, the two-phase-like colloid-polymer critical point sample begins to phase separate, or de-mix, into two phases-one that resembles a gas and one that resembles a liquid, except that the particles are colloids and not atoms. The colloid-poor black regions (colloidal gas) grow bigger, and the colloid-rich white regions (colloidal liquid) become whiter as the domains further coarsen. Finally, complete phase separation is achieved, that is, just one region of each colloid-rich (white) and colloid-poor (black) phase. This process was studied over four decades of length scale, from 1 micrometer to 1 centimeter.

Doherty, Michael P.↗
NASA NTRS2011

Framework for Integrating Science Data Processing Algorithms Into Process Control Systems

A software framework called PCS Task Wrapper is responsible for standardizing the setup, process initiation, execution, and file management tasks surrounding the execution of science data algorithms, which are referred to by NASA as Product Generation Executives (PGEs). PGEs codify a scientific algorithm, some step in the overall scientific process involved in a mission science workflow. The PCS Task Wrapper provides a stable operating environment to the underlying PGE during its execution lifecycle. If the PGE requires a file, or metadata regarding the file, the PCS Task Wrapper is responsible for delivering that information to the PGE in a manner that meets its requirements. If the PGE requires knowledge of upstream or downstream PGEs in a sequence of executions, that information is also made available. Finally, if information regarding disk space, or node information such as CPU availability, etc., is required, the PCS Task Wrapper provides this information to the underlying PGE. After this information is collected, the PGE is executed, and its output Product file and Metadata generation is managed via the PCS Task Wrapper framework. The innovation is responsible for marshalling output Products and Metadata back to a PCS File Management component for use in downstream data processing and pedigree. In support of this, the PCS Task Wrapper leverages the PCS Crawler Framework to ingest (during pipeline processing) the output Product files and Metadata produced by the PGE. The architectural components of the PCS Task Wrapper framework include PGE Task Instance, PGE Config File Builder, Config File Property Adder, Science PGE Config File Writer, and PCS Met file Writer. This innovative framework is really the unifying bridge between the execution of a step in the overall processing pipeline, and the available PCS component services as well as the information that they collectively manage.

Mattmann, Chris A.↗
NASA NTRSDate not supplied

Assimilation of Reconstructed Radiances from IASI Principal Component Scores into the GEOS-ADAS

Hyperspectral Infrared sounders such as IASI, AIRS, and CrIS have long been an integral part of radiance assimilation in numerical weather prediction (NWP), providing vertical profiles of water vapor and temperature information. Principal Component Scores (PCS) are a lossy form of compression that retains most information, such as temperature and moisture, by using a large training set of atmospheric profiles. However, PCS may not well represent profiles which are rare events, such as volcanic eruptions, and drops some sources of random noise. There has been an increased interest in the use of PCS as EUMETSAT plans to distribute future geostationary sounder radiances from MTG-IRS via PCS only. NWP centers use two approaches to deal with PCS: direct assimilation of the PCS by modifying the radiative transfer model to produce PCS and the associated Jacobians, or a simpler approach of decompressing the PCS and reconstructing the radiances back into channel space to allow assimilating radiances without modifications to the data assimilation system. EUMETSAT has developed a PCS product for IASI that has been operational since 2011. We utilize this product opting for the simpler approach, decompressing IASI PCS into channel space, and assimilating those radiances using the GEOS-ADAS. We then compare this with a control using the standard IASI radiance product. Resulting differences in global forecast statistics, differences in Forecast Sensitivity to Observation Impact, along with implications for implementation and quality control are discussed.

Bryan M. Karpowicz↗
NASA NTRS2023

Parker Solar Probe Observations of High Plasma β Solar Wind From the Streamer Belt

In general, slow solar wind from the streamer belt forms a high plasma β equatorial plasma sheet around the heliospheric current sheet (HCS) crossing, namely, the heliospheric plasma sheet (HPS). Current Parker Solar Probe (PSP) observations show that the HCS crossings near the Sun could be full or partial current sheet (PCS) crossings, and they share some common features but also have different properties. In this work, using the PSP observations from encounters 4–10, we identify streamer belt solar wind from enhancements in plasma β, and we further use electron pitch angle distributions to separate it into HPS solar wind around the full HCS crossings and PCS solar wind in the vicinity of PCS crossings. Based on our analysis, we find that the PCS solar wind has different characteristics as compared with HPS solar wind: (a) the PCS solar wind could be non-pressure-balanced structures rather than magnetic holes, and the total pressure enhancement mainly results from the less reduced magnetic pressure; (b) some of the PCS solar wind is mirror-unstable; and (c) the PCS solar wind is dominated by very low helium abundance but varied alpha–proton differential speed. We suggest that the PCS solar wind could originate from coronal loops deep inside the streamer belt, and it is pristine solar wind that still actively interacts with ambient solar wind; thus, it is valuable for further investigations of the heating and acceleration of slow solar wind.

Slow solar wind↗
NASA NTRSDate not supplied

Optimizing Consumable Gas Tank Usage while Maintaining Emergency Reserves Between Two Pressure Control Systems on Gateway

Two of NASA’s Lunar Space Station (Gateway) modules, the Habitation and Logistics Outpost (HALO) and International Habitat (IHAB) contain a pressure control system (PCS) that is used to supply Nitrogen (N2) and Oxygen (O2) to maintain a habitable environment within Gateway, with only one of the PCS active at any given time. To protect the crew during a contingency that is affecting pressure control and therefore gas consumables, Gateway is required to have sufficient amount of reserve consumable gas across the entire habitable Gateway stack of modules until the gas can be replenished by crew changing out a gas tank. This will occur in a non-contingency setting either on the current mission or on the next mission. To access the stack reserve Gateway features a Nitrogen Oxygen Transfer System (NOTS) between HALO and IHAB that allows each module’s PCS to access the gas tanks in the other module. The PCS designs are different between the two modules and lack interchangeable tanks so which module has active PCS must be accounted for in logistics planning. This paper describes the logistics resupply planning analysis used to determine the most efficient use of the tanks within each PCS, and a method for switching which module is active for PCS while maintaining the stack reserve that preserves enough gas to cover contingency cases.

Rachel Anne Sturtz↗
NASA NTRS2005

Fabrication of 3-D Photonic Band Gap Crystals Via Colloidal Self-Assembly

The behavior of photons in a Photonic Crystals, PCs, is like that of electrons in a semiconductor in that, it prohibits light propagation over a band of frequencies, called Photonic Band Gap, PBG. Photons cannot exist in these band gaps like the forbidden bands of electrons. Thus, PCs lend themselves as potential candidates for devices based on the gap phenomenon. The popular research on PCs stem from their ability to confine light with minimal losses. Large scale 3-D PCs with a PBG in the visible or near infra red region will make optical transistors and sharp bent optical fibers. Efforts are directed to use PCs for information processing and it is not long before we can have optical integrated circuits in the place of electronic ones.

Subramaniam, Girija↗
NASA NTRS1987

Microgravity fluid management requirements of advanced solar dynamic power systems

The advanced solar dynamic system (ASDS) program is aimed at developing the technology for highly efficient, lightweight space power systems. The approach is to evaluate Stirling, Brayton and liquid metal Rankine power conversion systems (PCS) over the temperature range of 1025 to 1400K, identify the critical technologies and develop these technologies. Microgravity fluid management technology is required in several areas of this program, namely, thermal energy storage (TES), heat pipe applications and liquid metal, two phase flow Rankine systems. Utilization of the heat of fusion of phase change materials offers potential for smaller, lighter TES systems. The candidate TES materials exhibit large volume change with the phase change. The heat pipe is an energy dense heat transfer device. A high temperature application may transfer heat from the solar receiver to the PCS working fluid and/or TES. A low temperature application may transfer waste heat from the PCS to the radiator. The liquid metal Rankine PCS requires management of the boiling/condensing process typical of two phase flow systems.

Migra, Robert P.↗
NASA NTRS1989

Enhanced resolution particle size distributions by multiple angle photon correlation spectroscopy

Photon correlation spectroscopy (PCS) has become a method of choice for measuring submicrometer particles. It is capable of rapid, accurate measurements of mean particle size. Since the measurements are nonperturbing, it is ideal for monitoring systems undergoing dynamic changes. Despite its widespread acceptance, the information content of PCS measurements for particle size distributions is low and provides limited resolution. A method is presented whereby PCS measurements made at several scattering angles plus the angular distribution of light scattered from the particles are combined in a single simultaneous analysis to effect an enhanced resolution particle size distribution. The efficacy of the method is assessed by recovering size distributions from computer simulated data and by comparisons of conventional PCS measurements of polystyrene spheres with those made by the new method.

Bott, Steven E.↗
NASA NTRS1994

Comparison of the seasonal and interannual variability of phytoplankton pigment concentrations in the Peru and California Current systems

Monthly composite images from the global coastal zone color scanner (CZCS) data set are used to provide an initial illustration and comparison of seasonal and interannual variability of phytoplankton pigment concentration along the western coasts of South and North America in the Peru Current system (PCS) and California Current system (CCS). The analysis utilizes the entire time series of available data (November 1978 to June 1986) to form a mean annual cycle and an index of interannual variability for a series of both latitudinal and cross-shelf regions within each current system. Within 100 km of the coast, the strongest seasonal cycles in the CCS are in two regions, one between 34 deg and 45 deg N and the second between 24 deg and 29 deg N, each with maximum concentrations (greater than 3.0 mg m(exp-3)) in May-June. Weaker seasonal variability is present north of 45 deg N and in the Southern California Bight region (32 deg N). Within the PCS, in the same 100-km-wide coastal region, highest (greater than 45 deg S) and lowest (less than 20 deg S) latitude regions have a similar seasonal cycle with maximum concentrations (greater than 1.5 mg m(exp -3)) during the austral spring, summer, and fall, matching that evident throughout the CCS. Between these regions, off northern and central Chile, the seasonal maximum occurs during July-August (austral winter), contrary to the influence of upwelling favorable winds. Within the CCS, the dominant feature of interannual variability in the 8-year time series is a strong negative concentration anomaly in 1983, an El Nino year. The relative value of this negative anomaly is strongest off central California and is followed by an even stronger negative anomaly is strongest off central California and is followed by an even stronger negative anomaly in 1984 off Baja, California. In the PCS, strong negative anomalies during the 1982-1983 El Nino period are evident only off the Peruvian coast and are evident there only in the regions 100 km or more from the coast. Although negative anomalies associated with the El Nino were not present at higher latitudes (more than approximately 20 deg S) in the PCS, the extremely sparse sampling weakens our confidence in the results of the interannual analysis in this region. An upper estimate of the systematic winter bias remaining in the global CZCS data after reprocessing with the multiple scattering algorithm is given in the appendix.

Thomas, A. C.↗
NASA NTRS2012

A Technique Using Principal Component Analysis to Compare Seasonal Cycles of Earth Radiation from CERES and Model Computations

A method for quantitatively comparing the seasonal cycles of two global data sets is presented. The seasonal cycles of absorbed solar radiation (ASR) and outgoing longwave radiation (OLR) have been computed from an eight-year data set from the Clouds and Earth's Radiant Energy System (CERES) scanning radiometers and from a model data set produced by the NASA Goddard Space Flight Center Global Modeling and Assimilation Office. To compare the seasonal cycles from these two data sets, principal component (PC) analysis is used, where the PCs express the time variations and the corresponding empirical orthogonal functions (EOFs) describe the geographic variations. Ocean has a long thermal response time compared to land, so land and ocean are separated for the analysis. The root-mean square values for the seasonal cycles of ASR and OLR are extremely close for the two data sets. The first three PCs are quite close, showing that the time responses and magnitudes over the globe are very similar. The agreement between the two sets of PCs is quantified by computing the matrix of inner products of the two sets. For ASR over land, the first PCs of CERES and the model agree to better than 99.9%. The EOF maps are similar for most of the globe, but differ in a few places, and the agreement of the EOF maps is likewise quantified. Maps of differences between the annual cycles show regions of agreement and disagreement.

Smith, G. Louis↗
NASA NTRS2015

ORION Environmental Control and Life Support Systems Suit Loop and Pressure Control Analysis

Under NASA's ORION Multi-Purpose Crew Vehicle (MPCV) Environmental Control and Life Support System (ECLSS) Project at Johnson Space Center's (JSC), the Crew and Thermal Systems Division has developed performance models of the air system using Thermal Desktop/FloCAD. The Thermal Desktop model includes an Air Revitalization System (ARS Loop), a Suit Loop, a Cabin Loop, and Pressure Control System (PCS) for supplying make-up gas (N2 and O2) to the Cabin and Suit Loop. The ARS and PCS are designed to maintain air quality at acceptable O2, CO2 and humidity levels as well as internal pressures in the vehicle Cabin and during suited operations. This effort required development of a suite of Thermal Desktop Orion ECLSS models to address the need for various simulation capabilities regarding ECLSS performance. An initial highly detailed model of the ARS Loop was developed in order to simulate rapid pressure transients (water hammer effects) within the ARS Loop caused by events such as cycling of the Pressurized Swing Adsorption (PSA) Beds and required high temporal resolution (small time steps) in the model during simulation. A second ECLSS model was developed to simulate events which occur over longer periods of time (over 30 minutes) where O2, CO2 and humidity levels, as well as internal pressures needed to be monitored in the cabin and for suited operations. Stand-alone models of the PCS and the Negative Pressure relief Valve (NPRV) were developed to study thermal effects within the PCS during emergency scenarios (Cabin Leak) and cabin pressurization during vehicle re-entry into Earth's atmosphere. Results from the Orion ECLSS models were used during Orion Delta-PDR (July, 2014) to address Key Design Requirements (KDR's) for Suit Loop operations for multiple mission scenarios.

Eckhardt, Brad↗
NASA NTRS2020

An Algorithm for Hyperspectral Remote Sensing of Aerosols: 3. Application to the GEO-TASO Data in KORUS-AQ Field Campaign

This paper describes the third part of a series of investigations to develop algorithms for simultaneous retrieval of aerosol parameters and surface spectral reflectance from the data measured by GEOstationary Trace gas and Aerosol Sensor Optimization (GEO-TASO) instrument. Since the algorithm is designed for future hyperspectral and geostationary satellite sensors, such as Tropospheric Emissions: Monitoring of Pollution (TEMPO), it is applied to GEO-TASO data measured over the same area by different flights as part of the Korea-United Stated Air Quality Study (KORUS-AQ) field campaign in 2016. While GEO-TAOS has a spectral sampling interval of ~0.28 nm in the visible, its data is thinned through a band selection approach with consideration of atmospheric transmittance and different surface types, which yields 20 common spectral bands to be used by the algorithm. The algorithm starts with 4 common principal components (PCs) for surface spectral reflectance extracted from various spectral libraries, and the constraints of surface reflectance parameters and aerosol scattering models respectively from k- means clustering analysis of the Rayleigh-corrected GEO-TASO spectra and AERONET data. The algorithm then proceeds iteratively with an optimal estimation approach to update PCs and retrieve aerosol optical depth (AOD) until the best match between simulated and GEOS-TASO measured spectra is achieved. The spectral AODs are compared between those retrieved from GEO-TASO (x) and 7 AERONETS (y) in 440, 550, 550, 675 nm, respectively. The comparison reveals that iterative updates of surface spectral PCs (and so surface reflectance) yield significant enhancement in AOD retrievals, improving the mean linear fitting equations from y = 0.735x + 0.088 (without update of PCs) to y = 1.055x+ 0.01, and the Pearson correlation coefficient (𝑅𝑅2) from 0.54 to 0.76, respectively. Move case studies are need to further evaluate the algorithm for its application to TEMPO that carries a enhanced version of GEO-TASO instrument.

Tropospheric Emissions: Monitoring of Pollution (T↗
NASA NTRSDate not supplied

Preservation of Provenance and Context to Ensure Future Understandability of Airborne Earth Observations and Derived Data Products

Open-source science goes beyond making data from scientific projects (e.g., on-orbit/satellite missions, airborne and field investigations, and other data producing activities) openly available after they are generated, but involves and open sharing of information throughout the project lifecycle. Preservation of the data and associated information required for understanding and reusing the data well after the scientific projects is a contributor to open-source science as well. Considering the high investment in the on-orbit/satellite missions, we had developed a document titled “NASA Earth Science Data Preservation Content Specification (PCS)” in 2011. This document has been used as a requirement for recent on-orbit/satellite missions by NASA. Recently it became clear that the specifications should be applied to other scientific projects as well. Therefore, the document was revised to cover other types of projects, and a Preservation Content Implementation Guidance (PCIG) document was also developed. The revised PCS, and the PCIG, were published in 2022. The purpose of this presentation is to highlight the contents of these documents as they apply to suborbital/airborne investigations. The PCS calls for content preservation in eight general categories - Measuring Instrument/Platform Description, Instrument and Science Data Products and Metadata, Science Raw Data, Product and Algorithm Documentation, Instrument Calibration, Science Algorithm Software, Science Data Product Algorithm Inputs, Science Data Product Validation, and Science Data Access and Analysis Tools. While all these categories apply to various types of projects, a few clarifying sentences have been added to the descriptions of contents in each of the categories to show which categories are especially important to airborne and field investigations and where some contents are not applicable (or difficult to obtain). The PCIG document provides some general guidance applicable to all types of projects and specific guidance in a separate section for airborne and field investigations. This section calls out typical artifacts produced during such investigations that can meet the spirit of the various PCS categories.

remote sensing↗
NASA NTRS1971

Attitude-referenced radiometer study. Part 2: Primary calibration system

A primary calibration system, PCS, for infrared radiometers has been developed, built, and tested. The system allows radiometers to be calibrated with less than 1 percent error for use in earth coverage horizon measurements, earth resources surveys, and synoptic meteorological measurement. The final design, fabrication and test of the PCS are reported. A detailed description of the PCS construction is presented, along with the results of a complete series of functional tests. Test to verify the source thermal characteristics, collimator reflectance, and output beam characteristics are described and their results presented.

Williamson, W. R.↗
NASA NTRS1981

Jay Carter Enterprises, Incorporated steam engine

The Small Community Solar Thermal Power Experiment (SCSE) selected an organic rankine cycle (ORC) engine driving a high speed permanent magnet alternator (PMA) as the baseline power conversion subsystem (PCS) design. The back-up conceptual PCS design is a steam engine driving an induction alternator delivering power directly to the grid. The development of the automotive reciprocating simple rankine cycle steam engine and how an engine of similar design might be incorporated into the SCSE is discussed. A description of the third generation automotive engine is included along with some preliminary test data. Tests were conducted with the third generation engine driving an induction alternator delivering power directly to the grid. The purpose of these tests is to further verify the effects of expander inlet temperature, input thermal power level, expansion ratio, and other parameters affecting engine performance to aid in the development of an SCSE PCS.

Source record↗