Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTICLE SIZE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

X-Ray Microtomography Measurements of Coevolving Particle Size and Shape

This study measures simultaneous changes in particle size and shape during grain crushing and proposes quantitative metrics to track their coevolving statistical distribution. Idealized granular materials with widely different initial particle shapes (i.e., spheres, quasi-ellipsoids, plates, and rods) are compressed oedometrically at vertical stress levels sufficient to induce particle breakage. X-ray microtomography and digital image analysis are then used to track changes in particle-scale characteristics. The observations indicate that more irregular particles tend to exhibit a higher degree of breakage compared to more spherical grains subjected to an equivalent stress level. Despite these differences, the measurements also indicate that all the tested particle sets approach a common attractor (expressed in terms of aspect ratio, flatness, and elongation), regardless of their initial morphology. A new shape evolution index is proposed to quantify such trends. With this new metric, it is shown that in all the tested materials, the particle shape evolves faster than size, especially for the more regular morphologies, thus implying that the shape tends to reach its attractor point before the grading reaches its ultimate particle size distribution. Furthermore, this finding underpins an ultimate stage of crushing-driven compression that occurs with particle size reduction but minimal shape changes (i.e., self-replicating shapes due to fractures).

Oedometric compression↗
DOE OSTI2025

Influence of particle size on NIR spectroscopic characterization of sorghum biomass for the biofuel industry

NIR spectroscopy is a rapid and accurate green technology for high-throughput biomass characterization, including sorghum (Sorghum bicolor), a promising energy crop for the biofuel industry. This study assessed the influence of particle size on NIR spectroscopic analysis (wavelength range: 867–2535 nm) of sorghum biomass composition. Grown under field conditions, a total of 113 types of genetically diverse sorghum accessions were dried, ground, and sieved (<250, 250–600, 600–850, and > 850 µm particle size) for developing partial least square regression (PLSR) prediction models for moisture, ash, extractive, glucan, xylan, acid-soluble lignin (ASL), acid-insoluble lignin (AIL), and total lignin (ASL + AIL). Overall, smaller particle sizes provided better model performance, while no single particle size provided the best performance for all the selected components. With only 9 selected bands and 4 latent variables (LVs), the best PLSR model was obtained for moisture with particle size of 600–850 µm with the square root of the coefficient of determination (R) of 0.85, the ratio of prediction to deviation (RPD) of 2.2, and the root mean square error (RMSE) of 0.46 % in external validation. Similar model performances were also obtained for ash, extractive, glucan, and xylan. This study showed that size reduction could effectively improve NIR spectroscopic analysis for lipid-producing sorghum biomass for the biofuel industry.

09 BIOMASS FUELS↗
DOE OSTI2022

The influence of particle size on the fluid dynamics of a laser-induced plasma

The interaction of a laser-induced shock wave with nanoparticles and microparticles of aluminum oxide is investigated through experiments and modeling. The chemistry and physics of the interaction between the particles and plasma generated from laser ablation shows similarities and discrete differences for the two particle sizes. For both particle sizes, early stage (< 10 μs) ionization was dominant and evidenced by higher concentrations of Al II. While both sizes exhibit ionization over the same duration, the intensity of emission was greater for nanoparticles indicating greater concentrations of ionized species. Moreover, the dispersion of species was notably more elongated for microparticles while radial dispersion was more pronounced for nanoparticles with elevated drag forces. At later stages (i.e., > 10 μs), oxidation reactions were dominant for both particle sizes, but the same distinctions in flow field were observed and attributed to particle drag. In all stages of interaction, microparticles expand axially with less drag that suppresses their radial expansion. As a result, the dispersion of reactive species was mapped over an up to 80% larger area for nanoparticles relative to microparticles. Results shown here can be applied toward advancing experimental diagnostics and particle-shock wave modeling and simulation efforts for energetic materials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Particle size distributions from TRACER-UFI

Particle size distributions using a custom-built SMPS. The measurements were made at the AMF-1 site in La Porte, TX between July 15, 2022 and August 30, 2022. The SMPS alternated between sampling ambient air and that in the portable Captive Aerosol Growth and Evolution (CAGE) chamber. The distributions from those two sources are separated.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Data for Influence of Particle Size on NIR Spectroscopic Characterization of Sorghum Biomass for the Biofuel Industry

NIR spectroscopy is a rapid and accurate green technology for high-throughput biomass characterization, including sorghum ( Sorghum bicolor ), a promising energy crop for the biofuel industry. This study assessed the influence of particle size on NIR spectroscopic analysis (wavelength range: 867–2535 nm) of sorghum biomass composition. Grown under field conditions, a total of 113 types of genetically diverse sorghum accessions were dried, ground, and sieved (<250, 250–600, 600–850, and > 850 µm particle size) for developing partial least square regression (PLSR) prediction models for moisture, ash, extractive, glucan, xylan, acid-soluble lignin (ASL), acid-insoluble lignin (AIL), and total lignin (ASL + AIL). Overall, smaller particle sizes provided better model performance, while no single particle size provided the best performance for all the selected components. With only 9 selected bands and 4 latent variables (LVs), the best PLSR model was obtained for moisture with particle size of 600–850 µm with the square root of the coefficient of determination (R) of 0.85, the ratio of prediction to deviation (RPD) of 2.2, and the root mean square error (RMSE) of 0.46 % in external validation. Similar model performances were also obtained for ash, extractive, glucan, and xylan. This study showed that size reduction could effectively improve NIR spectroscopic analysis for lipid-producing sorghum biomass for the biofuel industry.

Biomass Analytics↗
DOE OSTI2020

Exploring the relationship between solvent-assisted ball milling, particle size, and sintering temperature in garnet-type solid electrolytes

Garnet-type solid electrolytes, such as Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 (LLZTO), are promising materials for solid-state batteries, but processing remains a challenge, in part due to the high sintering temperature required for densification. Additionally, this temperature can be lowered by decreasing the initial particle size via solvent-assisted ball milling, but the relationship between solvent choice, particle properties, sintering behavior, and ionic conductivity is not well understood. In this work, we systematically explore these parameters, showing that milling in commonly used protic solvents, such as alcohols, effectively decreases the particle size but results in lithium loss (through Li + /H + exchange) that leads to poor sintering. By contrast, milling in aprotic solvents with surfactant reduces the particle size to ~220 nm without lithium loss, enabling the fabrication of dense samples (5.1 g/cm 3 ) with good ionic conductivity (0.43 mS/cm at 25 °C) at a lower sintering temperature (1000 °C). We compare ionic conductivities and activation energies for samples prepared with different particle sizes and sintering temperatures and use multiphase-field simulations to identify the mass transport and microstructural mechanisms responsible for the observed sintering dependence on particle size. These results further clarify the relationship between processing parameters and performance and represent important progress toward overcoming fabrication challenges for these materials.

25 ENERGY STORAGE↗
DOE OSTI2024

Particle size distributions from TRACER-MAP

Particle size distributions measured using a custom scanning mobility analyzer (SMPS) and a TSI, Inc. aerodynamic particle sizer (APS). The size distributions measured with the two instruments were merged during data inversion to produce a single distribution spanning a diameter range from approximately 19 nanometers to 15 micrometers. Size-dependent cloud condensation nuclei (CCN) activity measured with a CCN counter operated in parallel to the condensation particle counter in the SMPS are reported separately. The measurements were made from the Baylor University/University of Houston Mobile Air Quality Laboratory (MAQL) between July 5 and August 30, 2022 during the TRACER-MAP project. The trailer moved between five sites in the Houston regions as follows: Aldine: 7/5-7/8, 7/21-7/26, 8/15-8/24 University of Houston: 7/8-7/16, 8/8-8/15 San Jacinto monument: 7/16-7/21 Jones State Forest: 7/26-8/1; 8/24-8/30 AMF site in La Porte: 8/1-8/8

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Particle size distributions from TRACER-MAP

Particle size distributions measured using a custom scanning mobility analyzer (SMPS) and a TSI, Inc. aerodynamic particle sizer (APS). The size distributions measured with the two instruments were merged during data inversion to produce a single distribution spanning a diameter range from approximately 19 nanometers to 15 micrometers. Size-dependent cloud condensation nuclei (CCN) activity measured with a CCN counter operated in parallel to the condensation particle counter in the SMPS are reported separately. The measurements were made from the Baylor University/University of Houston Mobile Air Quality Laboratory (MAQL) between July 5 and August 30, 2022 during the TRACER-MAP project. The trailer moved between five sites in the Houston regions as follows: Aldine: 7/5-7/8, 7/21-7/26, 8/15-8/24 University of Houston: 7/8-7/16, 8/8-8/15 San Jacinto monument: 7/16-7/21 Jones State Forest: 7/26-8/1; 8/24-8/30 AMF site in La Porte: 8/1-8/8

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Effect of particle size and moisture on flow performance of loblolly pine anatomical fractions: Experimental findings and model predictions

The rising energy demand has highlighted biomass as a promising next-generation energy source. However, commercializing biomass-derived energy faces challenges, particularly in handling biomass feedstock. Factors like particle size, shape, moisture content, and surface roughness significantly impact biomass flowability. This study addresses a crucial knowledge gap by examining the effects of particle size and moisture content on the flow behavior and shear properties of different anatomical fractions of loblolly pine (Pinus taeda). The bulk shear behavior was examined using a Schulze ring shear tester, while flow performance was tested through gravity-driven flow experiments in a variable wedge-shape hopper. Results were incorporated into empirical and machine learning-based flow prediction models to evaluate their accuracy and limitations. The study found that samples with higher moisture content show higher unconfined yield strength. The critical arching distance increased with particle size, e.g., from approximately 13 and 33 mm for 2- and 6-mm whole chips, respectively at a 32-degree inclination angle. Conversely, the flow rate decreased for a given hopper opening as particle size increased. For instance, at a 60-mm hopper opening and a 32-degree inclination angle, the mass flow rates for 2- and 6-mm whole chips were 7.83 and 6.42 tonne/h, respectively. The empirical model consistently overpredicted the mass flow rate for all anatomical fractions, while the machine learning model more accurately predicted the central tendency of flow rate but was insensitive to varying tissue proportions. These novel findings provide comprehensive characterization of anatomical fractions, reveal significant combined effects of particle size and moisture content on biomass flow behavior, and demonstrate a better predictive accuracy of a machine learning model, all of which are useful for optimizing material handling strategies and biomass utilization technologies in the industry.

09 - BIOMASS FUELS↗
DOE OSTI2021

238 PuO 2 In Vitro Lung Dissolution Rate and Particle Size Determination for Material Involved in the June 8, 2020 Incident at the Los Alamos National Laboratory PF-4 Facility

As part of the LANL response to the June 8, 2020 238 PuO 2 inhalation exposure incident in PF-4, the Nuclear and Radiochemistry Group (C-NR) was asked to assist in determining the lung dissolution rate and particle size distribution of the airborne material. These material characteristics, along with urine and fecal bioassay data, are used by the Radiation Protection Services (RP-SVS) internal dosimetrists to refine dose estimates for exposed workers. Similar to previous studies, an in vitro lung dissolution rate study was performed to assess how fast 238 Pu is cleared from the lungs. Given that PuO 2 is a relatively insoluble material, it dissolves very slowly and requires in vitro studies of 100 or more days to estimate dissolution rates. This report details the results of a 100 day in vitro dissolution rate study and the particle size characteristics of 238 PuO 2 collected on an air filters during the incident. Results show that the 238 PuO 2 involved in this incident has behavior comparable to PuO 2 from previous in vitro studies, with approximately 1% of material dissolving quickly, and 99% of the material dissolving very slowly, with a half-time of approximately 120 years. This is somewhat slower than what was determined in a previous study of LANL 238 PuO 2 , which had an experimental dissolution half-time of 3 years, but significantly faster than 3000 years measured for 239 PuO 2 . Particle size distribution measurements indicate that particle sizes range from 0.10 µm – 6 µm, with most < 2 µm, which is reasonable based on our understanding of the process history of the 238 PuO 2 . Particle size, specific surface area, calcining temperature, specific activity, and age all are known factors that can impact the dissolution rate of refractory materials, however, there are too few studies to quantify the exact influence of these parameters on a measured dissolution rate. The results of this study add to that knowledge base, and provide new insights into the dissolution rates for this LANL process-specific 238 PuO 2 material.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2023

Effect of particle size on the capture of uranium oxide colloidal particles from aqueous suspensions via high-gradient magnetic filtration

The effectiveness of High Gradient Magnetic Filtration (HGMF) in capturing uranium oxide particles from suspensions was investigated in this study. Two sets of experiments were performed to evaluate the importance of size on the capture of uranium oxide particles. The first considered two batches sieved into size bins of< 5, 5–10, 10–15, and 15–20 µm, while the second was performed using two suspensions with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm. Iron oxide experiments, with particles between 0.3 and 0.8 µm, were performed for calibration purposes. In all experiments, a surfactant (Triton-X100 or sodium dodecyl sulfate) was used to prevent particle aggregation and limit the influence of non-magnetic capture mechanisms. A magnetic field of approximately 1.1 Tesla was generated using a water cooled electromagnet. HGMF was performed using tubular filters packed with ferromagnetic stainless-steel wool. Of the initial four uranium oxide particle sizes, magnetic capture was only observed for particles with a diameter of less than 5 µm, while larger particles experienced no magnetic and minimal total capture. For particles with diameters smaller than 1.0 µm and between 1.0 and 1.5 µm, capture efficiencies increased by 39 ± 9% and 34 ± 6% respectively, solely due to the magnetic field. Although the magnetic force is proportional to particle diameter, the capture efficiency decreased as diameter increased. So these results suggest that Brownian diffusion, which is influential for micron sized particles and increases with decreasing particle size, is acting in conjunction with the magnetic force to influence the efficacy of HGMF for uranium oxide. This important finding underscores the effectiveness of Brownian diffusion in increasing the rate of collision between particles and collector fibers. A stochastic trajectory model was developed to incorporate the influence of Brownian motion on particle behavior and filter removal efficiency. Modeling results are discussed and compared for uranium and iron oxide particles.

42 ENGINEERING↗
DOE OSTI2023

Effects of particle size, shape and loading rate on the normal compaction of an advanced granular ceramic

Compaction behavior of granular materials is influenced by strain rate, particle size, and shape. In this report, boron carbide powders with different particle sizes under uni-axial strain conditions are studied using quasi-static compression, dynamic Kolsky bar experiments and normal plate impact. A rounded powder is compacted to investigate the effect of particle shape. The normal plate impact technique is an excellent tool in characterization of powder compaction behavior up to strain rates of ~10 5 s -1 . From our experiments, granular boron carbide shows a highly compressible behavior with significant volume compaction. Constitutive responses are obtained for four powders. Particle fracture is identified as key deformation mechanism. Dynamic loading introduces more particle fragmentation than quasi-static loading. Morphological characterization of particle shapes shows that the deformation from powder compaction alters the particle shape distribution, which is also rate-dependent. Particle size, shape and strain rate effects on the normal stress are discussed accordingly.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Low-dimensional physics of clay particle size distribution and layer ordering

Abstract Clays are known for their small particle sizes and complex layer stacking. We show here that the limited dimension of clay particles arises from the lack of long-range order in low-dimensional systems. Because of its weak interlayer interaction, a clay mineral can be treated as two separate low-dimensional systems: a 2D system for individual phyllosilicate layers and a quasi-1D system for layer stacking. The layer stacking or ordering in an interstratified clay can be described by a 1D Ising model while the limited extension of individual phyllosilicate layers can be related to a 2D Berezinskii–Kosterlitz–Thouless transition. This treatment allows for a systematic prediction of clay particle size distributions and layer stacking as controlled by the physical and chemical conditions for mineral growth and transformation. Clay minerals provide a useful model system for studying a transition from a 1D to 3D system in crystal growth and for a nanoscale structural manipulation of a general type of layered materials.

42 ENGINEERING↗
DOE OSTI2021

Effect of Biochar and Biochar Particle Size on Plant-Available Water of Sand, Silt Loam, and Clay Soil

Biochar is being used as a soil amendment to improve soil hydraulic properties. It has been reported that biochar increases plant-available water, particularly in coarse-textured soils; however, effects on fine-textured soils are less pronounced. Here, we quantified the effects of biochar particle size on plant-available water in sand, silt loam, and clay soils. We amended these soils with a hydrophilic biochar, and packed soil-biochar mixtures into columns of 5.35-cm diameter and 3.0-cm height. Biochar was produced by gasification of woody forest residues. We applied the biochar at two different rates (0.5\% and 2\% by weight of C) and with four different biochar particle-size fractions ($<$4.75, $<$2.0, $<$1.0 and $<$0.5 mm). Our results show that biochar amendments increased the plant-available water (when expressed gravimetrically) of all three soils, particularly at the highest biochar application rate. Although the absolute increase in plant-available water was largest for the silt loam soil, the relative increase of plant-available water was greater for the sand than for the silt loam and clay. When expressed in volumetric terms, however, the effects on water retention were less pronounced: the sand showed a small increase in plant-available water with biochar amendment, and no change was observed with the silt loam and clay. Particle size of biochar had little effect on plant-available water (when expressed in gravimetric terms) in the three soils, but silt loam and clay showed increased plant-available water (when expressed in volumetric terms) with decreasing biochar particle size, while no effect was observed for the sand. While our findings corroborate many of the previously reported effects of biochar on soil-water retention, we show that the effects and their magnitude depend on whether the results are reported in terms of gravimetric or volumetric water contents. Because bulk density tends to decrease with increasing biochar application, so will the volumetric water content, and thus the magnitude of the effect on plant-available water will be smaller when expressed in volumetric water content.

hydraulic properties, water holding capacity, soil↗
DOE OSTI2022

Investigating Particle Size‐Dependent Redox Kinetics and Charge Distribution in Disordered Rocksalt Cathodes

Abstract Understanding how various redox activities evolve and distribute in disordered rocksalt oxides (DRX) can advance insights into manipulating materials properties for achieving stable, high‐energy batteries. Herein, the authors present how the reaction kinetics and spatial distribution of redox activities are governed by the particle size of DRX materials. The size‐dependent electrochemical performance is attributed to the distinct cationic and anionic reaction kinetics at different sizes, which can be tailored to achieve optimal capacity and stability. Overall, the local charged domains in DRX particles display random heterogeneity caused by the isotropic delithiation pathways. Owing to the kinetic limitation, the micron‐sized particles exhibit a holistic “core‐shell” charge distribution, whereas sub‐micron particles show more uniform redox reactions throughout the particles and ensembles. Sub‐micron DRX particles exhibit increasing anionic redox activities yet inferior cycling stability. In summary, engineering particle size can effectively modulate how cationic and anionic redox activities evolve and distribute in DRX materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Large-scale frictionless jamming with power-law particle size distributions

Due to significant computational expense, discrete element method simulations of jammed packings of size-dispersed spheres with size ratios greater than 1:10 have remained elusive, limiting the correspondence between simulations and real-world granular materials with large size dispersity. Here, invoking a recently developed neighbor binning algorithm, we generate mechanically stable jammed packings of frictionless spheres with power-law size distributions containing up to nearly 4 000 000 particles with size ratios up to 1:100. By systematically varying the width and exponent of the underlying power laws, we analyze the role of particle size distributions on the structure of jammed packings. The densest packings are obtained for size distributions that balance the relative abundance of large-large and small-small particle contacts. Although the proportion of rattler particles and mean coordination number strongly depend on the size distribution, the mean coordination of nonrattler particles attains the frictionless isostatic value of six in all cases. The size distribution of nonrattler particles that participate in the load-bearing network exhibits no dependence on the width of the total particle size distribution beyond a critical particle size for low-magnitude exponent power laws. This signifies that only particles with sizes greater than the critical particle size contribute to the mechanical stability. However, for high-magnitude exponent power laws, all particle sizes participate in the mechanical stability of the packing.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Regulating the properties of activated carbon for supercapacitors: impact of particle size and degree of aromatization of hydrochar

Hydrochar (HC), obtained by the hydrothermal carbonization (HTC) of biomass, is an excellent precursor for preparing activated carbon (AC). However, the effects of the intrinsic properties of HC on the microstructure and electrochemical properties of AC are largely unknown. Here, this study investigates the impact of particle size and the degree of aromatization of in-situ HC on the microstructure and electrochemical properties of AC. Our results show that a large particle size and a high degree of aromatization help protect the HC from overactivation by ZnCl 2 , resulting in an large specific surface area (SSA > 2000 m 2 /g) and high mesopore to micropore volume ratio value ( V mes /V mic > 0.3) of the AC. Electrochemical performance measurements show a maximum specific capacitance of 218 F/g at 0.5 A/g was achieved in all samples where the AC (AC180-10 h) was prepared by activating HC180-10 h with a large size, a high degree of aromatization, and abundant surface oxygen-containing functional groups. After AC180-10 h was assembled into a supercapacitor, the specific capacitance of AC180-10 h still reached 158 F/g at 0.5 A/g, and it showed excellent cycling stability. This study advances the understanding of the impact of HC particle size and degree of aromatization on AC properties, providing new insights into tailoring HC qualities so that improving improve the properties of AC.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Commercial aluminum powders, Part I: Particle size characterization and slow heating rate thermal analysis.

We characterized nine commercial aluminum (Al) powders using several methods to measure particle characteristics and thermal analysis, with the goal to understand how these parameters influence energy release. Although it is well-known that lot-to-lot variations in commercial nanoparticles are common, the Al powders were more heterogeneous than anticipated – both with regards to particle size distributions and impurities. Manufacturer specifications – often quoted in the literature without confirmation – were not always accurate for the specific sample lots we investigated. In several cases, different conclusions could be drawn from individual particle size techniques; a combination of multiple techniques provides a clearer picture of the powder properties. Thorough characterization of Al powders is required prior to interpretation of experimental results from a variety of applications. In particular, previous studies have shown contradictory results on the influence of Al on detonation performance, perhaps partially due to insufficient characterization of the Al powders themselves.

36 MATERIALS SCIENCE↗