Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

A fiber-optic technique for the measurement of contact angle in a clearance-fit pin-loaded hole

A fiber-optic technique for measuring contact angle during pin loading of a specimen is proposed. The experimental design and procedures for loading a 49.8-mm-diameter instrumented pin into an quasi-isotropic graphite-epoxy specimen are described. The optical fiber was located just above the surface of the pin outer diameter in order to obtain accurate pin-hole contact-angle measurements at increasing load levels. The movement of the optical fiber through the no-contact, contact, and no-contact regions is discussed; the photodiode output decreased monotonically as the fiber moved from the no-contact to the contact region and then decreased monotonically as the fiber moved from the contact region to the no-contact region. Variations in the contact angle measurements are examined as function of applied load level. The measurements are compared to contact angle values obtained using a finite element analysis and an electrical technique; it is determined that the data correlate well.

Prabhakaran, R.↗
NASA NTRS1971

Application of holographic optical techniques to bulk memory.

Current efforts to exploit the spatial redundancy and built-in imaging of holographic optical techniques to provide high information densities without critical alignment and tight mechanical tolerances are reviewed. Read-write-erase in situ operation is possible but is presently impractical because of limitations in available recording media. As these are overcome, it should prove feasible to build holographic bulk memories with mechanically replaceable hologram plates featuring very fast (less than 2 microsec) random access to large (greater than 100 million bit) data blocks and very high throughput (greater than 500 Mbit/sec). Using volume holographic storage it may eventually be possible to realize random-access mass memories which require no mechanical motion and yet provide very high capacity.

Anderson, L. K.↗
NASA NTRS1997

Improved Optical Techniques for Studying Sonic and Supersonic Injection into MACH-3 Flow. Video Supplement E-10853-V

This video supplements a report examining optical techniques for studying sonic and supersonic injection into MACH-3 flow The study used an injection-seeded, frequency doubled ND:YAG pulsed laser to illuminate a transverse section of the injectant plume. Rayleigh scattered light was passed through an iodine absorption cell to suppress stray laser light and was imaged onto a cooled CCD camera. The scattering was based on condensation of water vapor in the injectant flow. High speed shadowgraph flow visualization images were obtained with several video camera systems. Roof and floor static pressure data are presented several ways for the three configurations of injection designs with and without helium and/or air injection into Mach 3 flow.

Buggele, A. E.↗
NASA NTRS1983

Development of a simplified optical technique for the simultaneous measurement of particle size distribution and velocity

Existing techniques were surveyed, an experimental procedure was developed, a laboratory test model was fabricated, limited data were recovered for proof of principle, and the relationship between particle size distribution and amplitude measurements was illustrated in an effort to develop a low cost, simplified optical technique for measuring particle size distributions and velocities in fluidized bed combustors and gasifiers. A He-Ne laser illuminated Rochi Rulings (range 10 to 500 lines per inch). Various samples of known particle size distributions were passed through the fringe pattern produced by the rulings. A photomultiplier tube converted light from the fringe volume to an electrical signal which was recorded using an oscilloscope and camera. The signal amplitudes were correlated against the known particle size distributions. The correlation holds true for various samples.

Smith, J. L.↗
NASA NTRS1977

A directional filter diplexer using optical techniques for millimeter to submillimeter wavelengths

An optical diplexer for injection of a local oscillator into a mixer, useful in the submillimeter and short millimeter range, is described. It has very low insertion loss for both the signal and local oscillator (LO) and high rejection of LO noise. The measured performance of a unit tested at 337 GHz indicates a loss of about 0.2 dB for both inputs and 20-dB noise rejection.

Erickson, N. R.↗
NASA NTRS1979

Optical digital techniques

Optical interface losses between transmitter-to-fiber interface, connector-to-connector interface, and fiber-to-receiver interface were studied. System effects such as pulse dispersion, risetimes of the sources and detectors, type of fibers used, output power of the sources, and detector sensitivity were considered. Data bus systems such as TEE, Star, and Hybrid were analyzed. The matter of single fiber versus bundle technologies for future avionics systems was considered. The existing data bus system on Space Shuttle was examined and an optical analog was derived for a fiber bundle system, along with the associated power margin. System tests were performed on a feasibility model of a 9-port Star data bus system including BER, star losses, connector losses, etc. The same system was subjected to EMI between the range of 200 Hz to 10 GHz at 20V/m levels. A lightning test was also performed which simulated the conditions similar to those on Space Shuttle. The data bus system was found to be EMI and lightning hard. It is concluded that an optical data bus system is feasible for shuttle orbiter type vehicles.

Source record↗
NASA NTRS1976

Optical technique for measurement of random water wave surfaces

An optical system using the refraction of a vertical light ray has been developed for measuring the slope of random wind-generated water waves. The basic elements of the system are photovoltaic cells which are connected to individual amplifiers so that when the refracted light beam is incident on a cell, the output of the cell is amplified and then supplied as input to a comparator. The comparator then provides a specified voltage output, independent of the incident light intensity, as long as it is above a designated background value. The comparators are designed to give output voltages comparable with standard TTL. This arrangement provides a high signal from the cell when it experiences incident light, and a low signal when there is only background light, with the high and low signals at TTL voltage levels.

Sorrell, F. Y.↗
NASA NTRS2002

Evaluation of Mechanical Modal Characteristics Using Optical Techniques

In this paper the sensitivity of embedded fiber optic sensors to changes in modal characteristics of plates is discussed. In order to determine the feasibility of embedded fiber Bragg gratings for the detection of modal shapes and modal frequencies, a comparison of holographically imaged modes and the detected dynamic strain from embedded fiber optic Bragg gratings is made. Time averaged optical holography is used for the detection of mechanical defects, or damage, in various aerospace components. The damage is detected by measuring an alteration in structural dynamics, which is visually apparent when using time-averaged holography. These shifts in the mode shapes, both in frequency of the resonance and spatial location of vibration nodes, are caused by changes in parameters that affect the structure's mechanical impedance, such as stiffness, mass and damping, resulting from cracks or holes. It is anticipated that embedded fiber optic sensor arrays may also be able to detect component damage by sensing these changes in modal characteristics. This work is designed to give an initial indication to the feasibility of damage detection through the monitoring of modal frequencies and mode shapes with fiber optic sensors.

Lekki, John↗
NASA NTRS1974

Weather watch studies by means of an optical technique

A series of articles is presented on a passive, optical, cross beam system. The passive, optical, cross beam system was evaluated as a remote sensor of atmospheric conditions. The system employed the light scattered from natural aerosols to sense atmospheric mean and turbulent motion. A space-time correlation of the output of two optical sensors was used to evaluate the mean convective wind speed. In approximately 20% of the tests, signal-to-noise levels were sufficient to allow estimation of convective wind speeds. The feasibility of employing intersecting beams to evaluate the atmospheric turbulent motion was also investigated. The intersecting beams produced maximums in the space-time correlation curves for other than zero delay. The non-zero time delay maximums indicate the cross beam system was detecting aerosol layers in the atmosphere, rather than information from the common intersecting volume.

Turner, R. E.↗
NASA NTRS1985

Acousto-optic techniques for real SAR imaging

Recent advancements in the development of the Real Time Acousto-optic SAR Processor are presented. In particular, the technique for introducing the azimuth reference function into the processor via an acousto-optic Bragg cell is discussed. This approach permits the reference function to be stored in electronic memory, thus giving the processor the flexibility needed to adapt rapidly to changes in the radar/target geometry. The architecture is described and results are presented which show the applicability of the technique to both spot-light and strip-map SAR.

Haney, M.↗
NASA NTRS1992

Study of optical techniques for the Ames unitary wind tunnels. Part 3: Angle of attack

A review of optical sensors that are capable of accurate angle of attack measurements in wind tunnels was conducted. These include sensors being used or being developed at NASA Ames and Langley Research Centers, Boeing Airplane Company, McDonald Aircraft Company, Arnold Engineering Development Center, National Aerospace Laboratory of the Netherlands, National Research Council of Canada, and the Royal Aircraft Establishment of England. Some commercial sensors that may be applicable to accurate angle measurements were also reviewed. It was found that the optical sensor systems were based on interferometers, polarized light detector, linear or area photodiode cameras, position sensing photodetectors, and laser scanners. Several of the optical sensors can meet the requirements of the Ames Unitary Plan Wind Tunnel. Two of these, the Boeing interferometer and the Complere lateral effect photodiode sensors are being developed for the Ames Unitary Plan Wind Tunnel.

Lee, George↗
DOE OSTI2024

In-situ electrochemical optical techniques in the investigation of lithium interfacial phenomena with a liquid and a solid-state electrolyte

An in-situ electrochemical optical diagnosis is the key to the investigation of electrode interface during a redox reaction. Because the morphology changes particularly, dendrite formation, dendrite shapes, solid electrolyte interface formation and gas generation can be revealed visually. The challenge of ensuring uniform current density on a flat Li anode in a liquid electrolyte was addressed and uniform Li plating was demonstrated. The dendrite shape change under different reduction current density was discussed. Here the Li dendrite shape change and the performance of Li anodes with a surface lamination of graphite and red phosphate were used as examples to demonstrate the capability of the in-situ optical cell. An in-situ electrochemical optical cell used in the investigation of the increasingly popular solid-state Li batteries has its own challenges. Due to the untransparent nature of a solid-state electrolyte, an optical investigation on a solid-state electrolyte Li battery needs to be done by exposing the cross-section of the cell. In addition, it is very difficult to assemble an optical cell with a brittle and fragile solid-state electrolyte in a glove box. A set of formation and transfer dies, and an optical cell were introduced. The Li dendrite growth at the interface can be observed in a solid-state Li cell.

25 ENERGY STORAGE↗
NASA NTRS1982

Mount St. Helens dust veil observed at Boulder, Colorado by optical techniques

Following the May 18, 1980, eruption of Mount St. Helens, photometric and photograhic observations were taken at Boulder, Colorado, to record the optical effects of volcanic dust atmospherically transported to this area. The instruments used included a narrow-beamwidth solar photometer which recorded solar irradiance in eight narrow-bandwidth channels in the wavelength range 0.3 to 1.1 microns, a solar aureole photometer, and two time-lapse camera systems. The eight-channel solar photometer data have been analyzed to obtain the wavelength dependence of optical thickness. At the longer wavelengths, on May 20, 1980, the optical thickness was as much as nine times that expected from a 'clean atmosphere' model. During the first several days following the eruption, the dust veil sometimes exhibited sufficient spatial structure that its motion can be seen on the time-lapse films. The results of analysis to date are presented and the plans for additional analysis are outlined.

Lerfald, G.↗