Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OBLIQUE SHOCK WAVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Flow separation in oblique shock wave turbulent boundary layer interactions

Available experimental data on flow separation in shock wave turbulent boundary layer interactions are reviewed at hypersonic and supersonic speeds in two dimensional and axisymmetric interactions. The conditions leading to flow separation and the subsequent changes in the flow are discussed. The effects of the Mach number, Reynolds number, surface cooling and the methods of detecting separation are discussed. Pertinent experimental data for the separated flow characteristics in turbulent boundary layer oblique shock wave interactions are also presented and discussed. Empirical correlations for separated flows are also reviewed.

Hamed, A.↗
NASA NTRS1998

Flowfield Measurements in a Slot-Bled Oblique Shock Wave and Turbulent Boundary-Layer Interaction

An experimental investigation was conducted to determine the flowfield inside a bleed slot used to control an oblique shock-wave and turbulent boundary-layer interaction. The slot was oriented normal to the primary flow direction and had a width of 1.0 cm (primary flow direction), a length of 2.54 cm, and spanned 16.5 cm. The approach boundary layer upstream of the interaction was nominally 3.0 cm thick. Two operating conditions were studied: M = 1.98 with a shock generator deflection angle of 6 deg and M= 2.46 with a shock generator deflection angle of 8 deg. Measurements include surface and flowfield static pressure, Pitot pressure, and total mass-flow through the slot. The results show that despite an initially two-dimensional interaction for the zero bleed-flow case, the slot does not remove mass uniformly in the spanwise direction. Inside the slot, the flow is characterized by two separation regions which significantly reduce the effective flow area. The upper separation region acts as an aerodynamic throat resulting in supersonic flow through much of the slot.

Davis, D. O.↗
NASA NTRS1989

Interaction of an oblique shock wave with turbulent hypersonic blunt body flows

A shock-on-shock interaction near the cowl lip of an engine inlet is studied numerically by solving the compressible full Navier-Stokes equations. The present study focuses on Edney's type III shock interference pattern in which the turbulent free shear layer impinges on the cowl lip (modeled as a cylinder). Van Leer's flux-vector splitting upwind MUSCL scheme is used in the solver with algebraic turbulence models. Turbulent solutions of surface pressures and heat fluxes along the cowl lip are in reasonably good agreement with experiment except in the local shear layer impingement region. The present study showed some indications that higher order turbulent models may be required to improve the solution near the free shear layer impingement region.

Moon, Young J.↗
NASA NTRS1989

Experimental and analytical investigations of wave enhanced supersonic combustors

Supersonic combustion ramjet (scramjet) engines rely on rapid mixing and combustion of fuel for good performance. However, both of these processes are relatively slow compared to the residence times in supersonic combusters. Methods of improving the mixing process include subjecting the fuel streams to shock waves and the generation of vortices by spiriling, bifurcating struts. The combustion process can also be enhanced by shock or detonation waves. An oblique shock wave can act as a flameholder by increasing the pressure and temperature of the air-fuel mixture and thereby decreasing the ignition delay. If the oblique shock is sufficiently strong, then the combustion front and the shock wave can couple into a detonation wave. In this case, combustion occurs almost instantaneously in a thin zone behind the wave front. While the existence of standing oblique detonation waves has been proven in computer simulations, the experimental validation is still in progress. Currently, there is an experimental and analytical program at NASA-Ames Research Center to study detonations and other means of wave enhanced supersonic mixing and combustion.

Adelman, Henry G.↗
NASA NTRS1990

Shock interference heating in scramjet engines

Experimental and analytical research sponsored by the NASA Langley Research center and the NASP Structures Technology Maturation Program to define critical aerothermal loads for the NASP engine is summarized. Presented is a review of (1) shock-shock interaction on the engine cowl leading edge that results in a supersonic jet impinging on the leading edge surface and causes the heat transfer rate to be amplified by a factor of 30 or more over the undisturbed (no shock interaction) flow stagnation point heat transfer rate, (2) the effectiveness of supersonic film cooling with and without the effects of an impinging oblique shock wave, and (3) oblique shock impingement in an axial compression corner.

Wieting, Allan R.↗
NASA NTRS1974

Flowfield analysis for successive oblique shock wave-turbulent boundary-layer interactions

Description of a procedure for predicting the flowfields that develop when successive interactions between oblique shock waves and a turbulent boundary layer occur. Such interactions may occur, for example, in engine inlets for supersonic aircraft. A control volume analysis is used to predict changes in the flow field across the interactions. Two bleed flow models are considered. The predicted results are compared with measured results and are shown to be in good agreement when the bleed flow rate is low, or when there is no bleed. Shortcomings of the bleed flow models at higher bleed flow rates are discussed.

Sun, C.-C.↗
NASA NTRS1976

Flowfield analysis for successive oblique shock wave-turbulent boundary layer interactions

A computation procedure is described for predicting the flowfields which develop when successive interactions between oblique shock waves and a turbulent boundary layer occur. Such interactions may occur, for example, in engine inlets for supersonic aircraft. Computations are carried out for axisymmetric internal flows at M 3.82 and 2.82. The effect of boundary layer bleed is considered for the M 2.82 flow. A control volume analysis is used to predict changes in the flow field across the interactions. Two bleed flow models have been considered. A turbulent boundary layer program is used to compute changes in the boundary layer between the interactions. The results given are for flows with two shock wave interactions and for bleed at the second interaction site. In principle the method described may be extended to account for additional interactions. The predicted results are compared with measured results and are shown to be in good agreement when the bleed flow rate is low (on the order of 3% of the boundary layer mass flow), or when there is no bleed. As the bleed flow rate is increased, differences between the predicted and measured results become larger. Shortcomings of the bleed flow models at higher bleed flow rates are discussed.

Sun, C. C.↗
NASA NTRS2015

Experimental Study of Fillets to Reduce Corner Effects in an Oblique Shock-Wave/Boundary Layer Interaction

A test was conducted in the 15 cm x 15 cm supersonic wind tunnel at NASA Glenn Research Center that focused on corner effects of an oblique shock-wave/boundary-layer interaction. In an attempt to control the interaction in the corner region, eight corner fillet configurations were tested. Three parameters were considered for the fillet configurations: the radius, the fillet length, and the taper length from the square corner to the fillet radius. Fillets effectively reduced the boundary-layer thickness in the corner; however, there was an associated penalty in the form of increased boundary-layer thickness at the tunnel centerline. Larger fillet radii caused greater reductions in boundary-layer thickness along the corner bisector. To a lesser, but measureable, extent, shorter fillet lengths resulted in thinner corner boundary layers. Overall, of the configurations tested, the largest radius resulted in the best combination of control in the corner, evidenced by a reduction in boundary-layer thickness, coupled with minimal impacts at the tunnel centerline.

Fillets↗
NASA NTRS1989

Wave combustors for trans-atmospheric vehicles

A performance analysis is given of a conceptual transatmospheric vehicle (TAV). The TAV is powered by a an oblique detonation wave engine (ODWE). The ODWE is an airbreathing hypersonic propulsion system which utilizes shock and detonation waves to enhance fuel-air mixing and combustion in supersonic flow. In this wave combustor concept, an oblique shock wave in the combustor can act as a flameholder by increasing the pressure and temperature of the air-fuel mixture, thereby decreasing the ignition delay. If the oblique shock is sufficiently strong, then the combustion front and the shock wave can couple into a detonation wave. In this case, combustion occurs almost instantaneously in a thin zone behind the wave front. The result is a shorter lighter engine compared to the scramjet. The ODWE-powered hypersonic vehicle performance is compared to that of a scramjet-powered vehicle. Among the results outlined, it is found that the ODWE trades a better engine performance above Mach 15 for a lower performance below Mach 15. The overall higher performance of the ODWE results in a 51,000-lb weight savings and a higher payload weight fraction of approximately 12 percent.

Menees, Gene P.↗
NASA NTRS1953

Equations, tables, and charts for compressible flow

This report, which is a revision and extension of NACA-TN-1428, presents a compilation of equations, tables, and charts useful in the analysis of high-speed flow of a compressible fluid. The equations provide relations for continuous one-dimensional flow, normal and oblique shock waves, and Prandtl-Meyer expansions for both perfect and imperfect gases. The tables present useful dimensionless ratios for continuous one-dimensional flow and for normal shock waves as functions of Mach number for air considered as a perfect gas. One series of charts presents the characteristics of the flow of air (considered a perfect gas) for oblique shock waves and for cones in a supersonic air stream. A second series shows the effects of caloric imperfections on continuous one-dimensional flow and on the flow through normal and oblique shock waves. (author)

Source record↗
NASA NTRS1991

Heat transfer, velocity-temperature correlation, and turbulent shear stress from Navier-Stokes computations of shock wave/turbulent boundary layer interaction flows

The properties of 2-D shock wave/turbulent boundary layer interaction flows were calculated by using a compressible turbulent Navier-Stokes numerical computational code. Interaction flows caused by oblique shock wave impingement on the turbulent boundary layer flow were considered. The oblique shock waves were induced with shock generators at angles of attack less than 10 degs in supersonic flows. The surface temperatures were kept at near-adiabatic (ratio of wall static temperature to free stream total temperature) and cold wall (ratio of wall static temperature to free stream total temperature) conditions. The computational results were studied for the surface heat transfer, velocity temperature correlation, and turbulent shear stress in the interaction flow fields. Comparisons of the computational results with existing measurements indicated that (1) the surface heat transfer rates and surface pressures could be correlated with Holden's relationship, (2) the mean flow streamwise velocity components and static temperatures could be correlated with Crocco's relationship if flow separation did not occur, and (3) the Baldwin-Lomax turbulence model should be modified for turbulent shear stress computations in the interaction flows.

Wang, C. R.↗
NASA NTRS1991

Multiple shock-shock interference on a cylindrical leading edge

The details of an experimental study of shock wave interference heating on a cylindrical leading edge representative of the cowl of a rectangular hypersonic engine inlet are presented. This Mach 8 study has provided the first detailed pressure and heat transfer rate distributions on a cylinder resulting from a two-dimensional shockwave interference pattern created by two incident oblique shock waves intersecting the cylinder bow shock wave. The peak heat transfer rate was 38 times the undisturbed flow stagnation point level and occurred when the two oblique shock waves coalesced prior to intersecting the cylinder bow shock wave. Development of pressure deflection diagrams identified a new interference pattern consisting of concomitant supersonic jets separated from each other by a shear layer and submerged in the subsonic region between the bow shock wave and body.

Wieting, Allan R.↗
NASA NTRS1989

Wave combustors for trans-atmospheric vehicles

The Wave Combustor is an airbreathing hypersonic propulsion system which utilizes shock and detonation waves to enhance fuel-air mixing and combustion in supersonic flow. In this concept, an oblique shock wave in the combustor can act as a flameholder by increasing the pressure and temperature of the air-fuel mixture and thereby decreasing the ignition delay. If the oblique shock is sufficiently strong, then the combustion front and the shock wave can couple into a detonation wave. In this case, combustion occurs almost instantaneously in a thin zone behind the wave front. The result is a shorter, lighter engine compared to the scramjet. This engine, which is called the Oblique Detonation Wave Engine (ODWE), can then be utilized to provide a smaller, lighter vehicle or to provide a higher payload capability for a given vehicle weight. An analysis of the performance of a conceptual trans-atmospheric vehicle powered by an ODWE is given here.

Menees, Gene P.↗