Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NOISE MEASUREMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Flyover-noise measurement and prediction

Details are presented for the measurement and prediction of aircraft flyover noise to be used for certification, research and development, community noise surveys, airport monitors, and pass fail criteria. Test details presented are applicable to all types of aircraft, both large and small, and the use of Federal Aviation Regulations (FAR) Part 36 (ref. 1) is emphasized. Accuracy of noise measurements is important. Thus, a pass-fail criterion should be used for all noise measurements. Finally, factors which influence the sound propagation and noise prediction procedures, such as atmospheric and ground effects, are also presented.

Peart, Noel A.↗
NASA NTRS1984

Analysis of noise measured from a propeller in a wake

In this experimental study, the acoustic characteristics of a propeller operating in a wake were studied. The propeller performance and noise were measured from two 0.25 scale propellers operating in an open jet anechoic flow environment with and without a wake. One propeller had NACA 16 series sections; the other, ARA-D. Wake thicknesses of 1 and 3 propeller chords were generated by an airfoil which spanned the full diameter of the propeller. The airfoil wake profiles were measured. Noise measurements were made in and out of the flow. The propellers were operated at 40, 83, and 100 inf of thrust. The acoustic data are analyzed, and the effects on the overall sound pressure level (OASPL) and scaled A weighted sound level L sub A with propeller thrust, wake thickness, and observer location are presented. The analysis showed that, generally, the wake increased the overall noise (OASPL) produced by the propeller; increased the harmonic content of the noise, thus the scaled L sub a; and produced an azimuthal dependence. With few exceptions, both propellers generally produced the same trends in delta OASPL and delta L sub a with thrust and wake thickness.

Block, P. J. W.↗
NASA NTRS1976

Experimental clean combustor program; noise measurement addendum, Phase 2

Combustor noise measurements were performed using wave guide probes. Test results from two full scale annular combustor configurations in a combustor test rig are presented. A CF6-50 combustor represented a current design, and a double annular combustor represented the advanced clean combustor configuration. The overall acoustic power levels were found to correlate with the steady state heat release rate and inlet temperature. A theoretical analysis for the attenuation of combustor noise propagating through a turbine was extended from a subsonic relative flow condition to include the case of supersonic flow at the discharge side. The predicted attenuation from this analysis was compared to both engine data and extrapolated component combustor data. The attenuation of combustor noise through the CF6-50 turbine was found to be greater than 14 dB by both the analysis and the data.

Emmerling, J. J.↗
NASA NTRS1988

Structureborne noise measurements on a small twin-engine aircraft

Structureborne noise measurements performed on a twin-engine aircraft (Beechcraft Baron) are reported. There are two overall objectives of the test program. The first is to obtain data to support the development of analytical models of the wing and fuselage, while the second is to evaluate effects of structural parameters on cabin noise. Measurements performed include structural and acoustic responses to impact excitation, structural and acoustic loss factors, and modal parameters of the wing. Path alterations include added mass to simulate fuel, variations in torque of bolts joining wing and fuselage, and increased acoustic absorption. Conclusions drawn regarding these measurements are presented.

Cole, J. E., III↗
NASA NTRS2019

Noise Measurements of a Low-Noise Top-Mounted Propulsion Installation for a Supersonic Airliner

A model-scale exhaust system was tested to validate low-noise concepts and noise prediction methods. The tests involved far-field acoustics, translating phased array, and particle image velocimetry; this report covers the far-field acoustic measurements. Data were acquired for a series of nozzles with different chevron designs, both uninstalled and installed on a representative aircraft planform. The impact of the various chevron treatments on the far-field noise was documented, along with the impact of the pylon and planform. For the baseline nozzle, installation produced a 2EPNdB reduction, as assumed in system studies. Chevrons were used to shift noise sources upstream to maximize the installation benefits and to reduce unshielded sources downstream. These resulted in reductions of 4-5EPNdB relative to the uninstalled baseline nozzle. Detailed analysis of spectral directivities behind the integrated EPNL metric gave insight into how well these concepts actually work. When correlated with particle image velocimetry measurements and phased array measurements, reported in companion papers, the explanation of acoustic benefits from top-mounted propulsion is clear as is the path toward optimization of the concept.

Supersonics↗
NASA NTRS2019

PIV/Phased Array/Far-Field Noise Measurements of a Low-Noise Top-Mounted Propulsion Installation for a Supersonic Airliner

A model-scale exhaust system was tested to validate low-noise concepts and noise prediction methods. The tests involved far-field acoustics, translating phased array, and particle image velocimetry; this report covers the far-field acoustic measurements. Data were acquired for a series of nozzles with different chevron designs, both uninstalled and installed on a representative aircraft planform. The impact of the various chevron treatments on the far-field noise was documented, along with the impact of the pylon and planform. For the baseline nozzle, installation produced a 2 EPNdB (Effective Perceived Noise in deciBels) reduction, as assumed in system studies. Chevrons were used to shift noise sources upstream to maximize the installation benefits and to reduce unshielded sources downstream. These resulted in reductions of 4-5 EPNdB...

Bridges, James↗
NASA NTRS1975

Some effects of the atmosphere and microphone placement on aircraft flyover noise measurements

The effects of varying atmospheric conditions on certification-type noise measurements were studied. Tests were made under various atmospheric conditions at two test sites, Fresno, California, and Yuma, Arizona, using the same test aircraft, noise, and weather measuring equipment, and operating personnel. Measurements were made to determine the effects of the atmosphere and of microphone placement on aircraft flyover noise. The measurements were obtained for characterization of not only the acoustic signature of the test aircraft, but also specific atmospheric characteristics. Data are presented in the form of charts and tables which indicate that for a wide range of weather conditions, at both site locations, noise data were repeatable for similar aircraft operating conditions. The placement of microphones at ground level and at 1.2 m over both spaded sand and concrete illustrate the effects of ground reflections and surface impedance on the noise measurements.

Hosier, R. N.↗
NASA NTRS1985

Thermionic noise measurements for on-line dispenser cathode diagnostics for linear beam microwave tubes

A test stand has been set up to measure the current fluctuation noise properties of B- and M-type dispenser cathodes in a typical TWT gun structure. Noise techniques were used to determine the work function distribution on the cathode surfaces. Significant differences between the B and M types and significant changes in the work function distribution during activation and life are found. In turn, knowledge of the expected work function can be used to accurately determine the cathode-operating temperatures in a TWT structure. Noise measurements also demonstrate more sensitivity to space charge effects than the Miram method. Full automation of the measurements and computations is now required to speed up data acquisition and reduction. The complete set of equations for the space charge limited diode were programmed so that given four of the five measurable variables (J, J sub O, T, D, and V) the fifth could be computed. Using this program, we estimated that an rms fluctuation in the diode spacing d in the frequency range of 145 Hz about 20 kHz of only about 10 to the -5 power A would account for the observed noise in a space charge limited diode with 1 mm spacing.

Holland, C.↗
NASA NTRS2024

Aircraft Parameter Estimation Considering Process and Measurement Noise

A practical formulation is proposed for parameter estimation using the filter-error method, which is a maximum-likelihood estimator for dynamic systems having both process and measurement noise inputs. The novelty of the proposed formulation is that by accurately estimating the measurement noise covariance matrix using a time series analysis method, the remaining unknowns (which include the unknown parameters in the state-space matrices and the process noise covariance matrix) become decorrelated and can be estimated simultaneously in a straightforward manner. The approach is demonstrated using simulation data and flight test data from a subscale airplane. Results indicate that proposed algorithm can obtain accurate modeling results when both measurement noise and process noise are present in the data.

Kalman filter↗
NASA NTRS1963

NON-THERMAL NOISE MEASUREMENTS NEAR PLANETS

Measurements of cosmic noise, solar and jovian noise bursts, atmospheric noise and whistlers and vlf emissions, for the study of planetary ionization and magnetic fields

WHISTLER↗
NASA NTRS1971

Ground noise measurements during landing, take-off, and flyby operations of a four-engine turbopropeller STOL airplane

Noise measurements were obtained for a four-engine turbopropeller STOL airplane during a Federal Aviation Administration flight evaluation program at the National Aviation Facilities Experimental Center. These noise measurements involved landing-approach, takeoff-climbout, and flyby operations of the airplane. A total of 13 measuring positions were used to define the noise characteristics around a simulated STOL port. The results are presented in the form of both physical and subjective measurements. An appendix is included to present tabulated values of various subjective reaction units which may be significant for the planning and operation of STOL ports. The main source of noise produced by this vehicle was found to be the propeller, and noise levels decrease generally in accordance with the inverse-distance law for distances up to about 457 meters. For similar slant ranges, somewhat lower noise levels were experienced during flyby than during takeoff or landing.

Hilton, D. A.↗
NASA NTRS1972

Analysis of normal shock noise measurements on nose-cylinder bodies.

Aerodynamic noise measurements have been obtained on three nose-cylinder configurations (15 deg cone-cylinder, biconic nose-cylinder and biconic nose-corrogated cylinder) in transonic flow. The noise environment at the foot of the terminal normal shock and its associated separated flow bubble were examined in detail. A peak in the frequency spectra of the separated flow region was observed which compares well with the predicted resonance frequency of the separated pocket using Trilling's incident shock model. As a consequence of the observed sound spectra and noise level, a flow model is postulated which consist of a cellular separated flow region. In the central portion of the cell the flow resembles the classical two-dimensional recirculating bubble, but each cell is vented by a pair of counter rotating vortices, which start at the surface and steam downstream.

Reding, J. P.↗
NASA NTRS1973

Noise measurements taken at LAX during operational evaluation of two-segment approaches in a 727-200 aircraft

A series of seven noise measurements were made each day over a period of fifteen days. The first and last flights each day were made by a specially instrumented 727-200 aircraft being used to evaluate the operational effectiveness of two-segment noise abatement approaches in scheduled service. Noise measurements were made to determine the noise reduction benefits of the two-segment approaches.

Tanner, C. S.↗
NASA NTRS1984

Installation noise measurements of model SR and CR propellers

Noise measurements on a 0.1 scale SR-2 propeller in a single and counter rotation mode, in a pusher and tractor configuration, and operating at non-zero angles of attack are summarized. A measurement scheme which permitted 143 measurements of each of these configurations in the Langley 4- by 7-meter low speed tunnel is also described.

Block, P. J. W.↗
NASA NTRS1973

Results of the noise measurement program on a standard and modified OH-6A helicopter

A field noise measurement program has been conducted on a standard OH-6A helicopter and one that had been modified by reducing the rotor speed, altering rotor tip shape, and treating the engine exhaust and inlet to reduce the external noise levels. The modifications consisted of extensive aircraft design changes resulting in substantial noise reductions following state-of-art noise reduction techniques. The purpose of this study was to document the ground noise characteristics of each helicopter during flyover, hover, landing, and take-off operations. Based on an analysis of the measured results, the average of the overall on-track noise levels of the final modified helicopter was approximately 14 db lower than that for the standard helicopter. Narrow-band-spectra data of the hovering helicopter show a reduction in the overall noise due to the reductions achieved for the lifting main and antitorque tail rotor, engine exhaust, and gear box noise for the modified helicopter. The noise results of the test program are found to correlate generally with noise measurements made previously on this type of aircraft.

Henderson, H. R.↗