Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NEAT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Investigation of the relations between neat resin and advanced composite mechanical properties. Volume 1: Results

A detailed evaluation of one untoughened epoxy baseline resin and three toughened epoxy resin systems was performed. The Hercules 3502, 2220-1, and 2220-3, and Ciba-Geigy Fibredux 914 resin systems were supplied in the uncured state by NASA-Langley and cast into thin flat specimens and round dogbone specimens. Tensile and torsional shear measurements were performed at three temperatures and two moisture conditions. Coefficients of thermal expansion and moisture expansion were also measured. Extensive scanning electron microscopic examination of fracture surfaces was performed, to permit the correlation of observed failure modes with the environmental conditions under which the various specimens were tested. A micromechanics analysis was used to predict the unidirectional composite response under the various test conditions, using the neat resin experimental results as the required input data. Mechanical and physical test results, the scanning electron microscope observations, and the analytical predictions were then correlated.

Zimmerman, R. S.↗
NASA NTRS1987

High performance thermoplastics: A review of neat resin and composite properties

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness. Attractive features and problems involved in the use of thermo-plastics as matrices for high performance composites are discussed.

Johnston, Norman J.↗
NASA NTRS1988

Dimpling Tools Would Form Fastener Neatly

Proposed set of tools neatly dimple cup washer to prevent screw from turning in mounting hole. Two dimples required, one leaning outward to grip recess in mounting hole and one leaning inward to grip recess in screw-head. Tools do not cause cracks and tears. Substitute die-forming process for hammer-and-center-punch process. De-forming process requires less skill and gives results of greater quality and consistency.

Roberts, Michael D.↗
NASA NTRS1987

High performance thermoplastics - A review of neat resin and composite properties

A review was made of the principal thermoplastics used to fabricate high performance composites. Neat resin tensile and fracture toughness properties, glass transition temperatures (Tg), crystalline melt temperatures (Tm) and approximate processing conditions are presented. Mechanical properties of carbon fiber composites made from many of these thermoplastics are given, including flexural, longitudinal tensile, transverse tensile and in-plane shear properties as well as short beam shear and compressive strengths and interlaminar fracture toughness.

Johnston, Norman J.↗
NASA NTRS2004

PETI-298 Prepared by Microwave Synthesis: Neat Resin and Composite Properties

PETI-298 is a high temperature/high performance matrix resin that is processable into composites by resin transfer molding (RTM), resin infusion and vacuum assisted RTM techniques. It is typically synthesized in a polar aprotic solvent from the reaction of an aromatic anhydride and a combination of diamines and endcapped with phenylethynylphthalic anhydride. Microwave synthesis of PETI-298 was investigated as a means to eliminate solvent and decrease reaction time. The monomers were manually mixed and placed in a microwave oven for various times to determine optimum reaction conditions. The synthetic process was subsequently scaled-up to 330g. Three batches were synthesized and combined to give 1 kg of material that was characterized for thermal and rheological properties and compared to PETI-298 prepared by the classic solution based synthetic method. The microwave synthesized PETI-298 was subsequently used to fabricate flat laminates on T650 carbon fabric by RTM. The composite panels were analyzed and mechanical properties determined and compared with those fabricated from PETI-298 prepared by the classic solution method. The microwave synthesis process and characterization of neat resin and carbon fiber reinforced composites fabricated by RTM will be presented. KEY WORDS: Resin Transfer Molding, High Temperature Polymers, Phenylethynyl Terminated Imides, Microwave Synthesis

Smith, Joseph G.↗
NASA NTRS2004

High Silicate Crystalline-to-Amorphous Ratios in Comets C/2001 Q4 (NEAT) and Hale-Bopp

Crystalline silicates, by their apparent absence in the ISM, are dust grains that experienced high temperatures in the solar nebula. Mg-rich crystalline silicates formed either by condensation from hot nebular gases (1450 K) or by the annealing of Mg-rich amorphous silicates (approx. 1000 K) in shocks in the 5-10 AU region or by radial transport into and out of the hot inner zones, e.g., T(sub d) > 1000 K at r(sub h) < 5 AU, 10(exp -6) - 10(exp -5) M(sub O)/yr, alpha = 10(exp -4) of the early solar nebula. Mg-rich crystalline silicates are found in interplanetary dust particles (IDPs) and produce IR spectral features in many Oort cloud comets. In May 2004, we discovered strong crystalline silicate features in the dynamically new Oort cloud comet C/2001 Q4 (NEAT). Thermal emission modeling of comets Q4 and C/1995 O1 (Hale-Bopp) demonstrate that both these comets have similar, high silicate crystalline-to-amorphous ratios of 2.4 and 2.1, respectively, indicating that these icy planetesimals aggregated from similar reservoirs of material or that crystalline silicates were widely distributed within the comet-forming zone. This argues for efficient annealing mechanisms and radial mixing.

Wooden, D. H.↗
NASA NTRS2004

High Silicate Crystalline-to-Amorphous Ratios in Comets C/2001 Q4 (NEAT) and Hale-Bopp

Crystalline silicates, by their apparent absence in the ISM, are dust grains that experienced high temperatures in the solar nebula. Mg-rich crystalline silicates formed either by condensation from hot nebular gases (1450 K) or by the annealing of Mg-rich amorphous silicates (approximately 1000 K) in shocks in the 5-10AU region or by radial transport into and out of the hot inner zones, e.g., T(sub d) greater than 1000K at r(sub h) less than 5AU, 10(exp -6) -10(exp -5) solar mass per year, alpha = 10(exp -4) of the early solar nebula. Mg-rich crystalline silicates are found in interplanetary dust particles (IDPs) and produce IR spectral features in many Oort cloud comets. In May 2004, we discovered strong crystalline silicate features in the dynamically new Oort cloud comet C/2001 Q4 (NEAT). Thermal emission modeling of comets Q4 and C/1995 O1 (Hale-Bopp) demonstrate that both these comets have similar, high silicate crystalline-toamorphous ratios of 2.4 and 2.1, respectively, indicating that these icy planetesimals aggregated from similar reservoirs of material or that crystalline silicates were widely distributed within the comet-forming zone. This argues for efficient annealing mechanisms and radial mixing.

Wooden, D. H.↗
NASA NTRS2011

Nearby Exo-Earth Astrometric Telescope (NEAT)

NEAT (Nearby Exo ]Earths Astrometric Telescope) is a modest sized (1m diameter telescope) It will be capable of searching approx 100 nearby stars down to 1 Mearth planets in the habitable zone, and 200 @ 5 Mearth, 1AU. The concept addresses the major issues for ultra -precise astrometry: (1) Photon noise (~0.5 deg dia field of view) (2) Optical errors (beam walk) with long focal length telescope (3) Focal plane errors , with laser metrology of the focal plane (4) PSF centroiding errors with measurement of the "True" PSF instead of using a "guess " of the true PSF, and correction for intra pixel QE non-uniformities. Technology "close" to complete. Focal plane geometry to 2e-5 pixels and centroiding to approx 4e -5 pixels.

exoplanets↗
NASA NTRS2018

NEAT Summary and Update

Overview of NEAT testbed for general audience with updates based on 2018 work performed.

Dyson, Rodger↗
NASA NTRS1985

Radio-frequency electrical properties of some neat and metal-doped polyimides

As the size and complexity of aerospace systems increase, the uses of polymers are also expected to increase. Polyimides constitute one promising generic class of polymeric materials. They retain good mechanical and physical properties at higher temperatures and absorb less moisture than do the epoxies, which are the polymers most frequently used in present aerospace systems. The properties of these polyimide materials are, therefore, of considerable interest to the aerospace community. Of particular importance are the electrical properties because these properties relate to both electrical and structural applications.

Long, E. R., Jr.↗
NASA NTRS1989

Effects of postcuring on mechanical properties of pultruded fiber-reinforced epoxy composites and the neat resin

The effects of postcuring on mechanical properties of pultruded fiber-reinforced epoxy-resin composites have been investigated. Composites with carbon, glass, and aramid reinforcement fibers were individually studied. The epoxy was a commercially-available resin that was especially developed for pultrusion fabrication. The pultrusions were conducted at 400 F with postcures at 400, 450, 500, and 550 F. Measurements of the flexural, shear, and interlaminar fracture-toughness properties showed that significant postcuring can occur during the pultrusion process. All three mechanical properties were degraded by the higher (500 and 550 F) temperatures; photomicrographs suggest that the degradation was caused at the fiber-resin interface for all three fiber types.

Long, Edward R., Jr.↗
NASA NTRS1997

The Kepler Mission: A Mission to Determine the Frequency of Inner Planets Neat the Habitable Zone of a Wide Range of Stars

The surprising discovery of giant planets in inner orbits around solar-like stars has brought into question our understanding of the development and evolution of planetary systems, including our solar system. To make further progress, it is critical to detect and obtain data on the frequency and characteristics of Earth-class planets. The Kepler Mission is designed to be a quick, low-cost approach to accomplish that objective. Transits by Earth-class planets produce a fractional change in stellar brightness of 5 x 10(exp -5) to 40 x 10(exp -5) lasting for 4 to 16 hours, From the period and depth of the transits, the orbit and size of the planets can be calculated. The proposed instrument is a one-meter aperture photometer with a 12 deg field-of-view (FOV). To obtain the required precision and to avoid interruptions caused by day-night and seasonal cycles, the photometer will be launched into a heliocentric orbit. It will continuously and simultaneously monitor the flux from 80,000 dwarf stars brighter than 14th magnitude in the Cygnus constellation. The mission tests the hypothesis that the formation of most stars produces Earth-class planets in inner orbits. Based on this assumption and the recent observations that 2% of the stars have giant planets in inner orbits, several types of results are expected from the mission: 1. From transits of Earth-class planets, about 480 planet detections and 60 cases where two or more planets are found in the same system. 2. From transits of giant planets, about 160 detections of inner-orbit planets and 24 detections of outer-orbit planets. 3. From the phase modulation of the reflected light from giant planets, about 1400 planet detections with periods less than a week, albedos for 160 of these giant planets, and densities for seven planets.

Borucki, W. J.↗