Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Morphology optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Efficient and mechanically-robust organic solar cells based on vertical stratification modulation through sequential blade-coating

Mechanically durable organic solar cells (OSCs) with high efficiency are deemed as the ideal candidate for the power source of the next generation wearable electronic devices. However, the brittle nature of small molecules in most high-efficiency OSCs consisting of polymer and small molecule encourages easy formation of cracks in the photoactive film under deformation. Here, the vertical composition distribution of the active layer has been well optimized through sequential blade coating to realize highly deformable while efficient OSC. The optimized morphology exhibits distinct donor-rich and homogenous region distributed along the vertical direction in the bulk. The donor-rich region provides sufficient chain entanglements and strong interfaces beneficial for mechanical robustness of film, while homogeneously mixed region offers continuous interpenetrating network to maintain high device through-put, resulting in superior efficiency of 14.4% with high crack-onset strain (COS) of 30.5%. This efficiency versus COS combination is much higher than the best combination reported in all polymer systems (COS of 15.9% and efficiency of 11.1%). To the best of our knowledge, it is the highest COS value achieved in polymer-small molecule systems. As a result, the rational control over vertical stratification demonstrated here would guide researchers in the development of innovative wearable electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-temperature low-humidity proton exchange membrane with “stream-reservoir” ionic channels for high-power-density fuel cells

The perfluorosulfonic acid (PFSA) proton exchange membrane (PEM) is the key component for hydrogen fuel cells (FCs). We used in situ synchrotron scattering to investigate the PEM morphology evolution and found a “stream-reservoir” morphology, which enables efficient proton transport. The short-side-chain (SSC) PFSA PEM is fabricated under the guidance of morphology optimization, which delivered a proton conductivity of 193 milliSiemens per centimeter [95% relativity humidity (RH)] and 40 milliSiemens per centimeter (40% RH) at 80°C. The improved glass transition temperature, water permeability, and mechanical strength enable high-temperature low-humidity FC applications. Performance improvement by 82.3% at 110°C and 25% RH is obtained for SSC-PFSA PEM FCs compared to Nafion polymer PEM devices. The insights in chain conformation, packing mechanism, crystallization, and phase separation of PFSAs build up the structure-property relationship. In addition, SSC-PFSA PEM is ideal for high-temperature low-humidity FCs that are needed urgently for high-power-density and heavy-duty applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Self-assembled multifunctional nanostructures for surface passivation and photon management in silicon photovoltaics

This work reports the fabrication and characterization of multifunctional, nanostructured passivation layers formed using a self-assembly process that provide both surface passivation and improved light trapping in crystalline silicon photovoltaic (PV) cells. Scalable block copolymer self-assembly and vapor phase infiltration processes are used to form arrays of aluminum oxide nanostructures (Al 2 O 3 ) on crystalline silicon without substrate etching. The Al 2 O 3 nanostructures are characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and spectroscopic ellipsometry. Injection-level dependent photoconductance measurements are used to determine the effective carrier lifetime of the samples to confirm the nanostructures successfully passivate the Si surface. Finite element method simulations and reflectance measurement show that the nanostructures increase the internal rear reflectance of the PV cell by suppressing the parasitic optical losses in the metal contact. An optimized morphology of the structures is identified for their potential use in PV cells as multifunctional materials providing surface passivation, photon management, and carrier transport pathways.

14 SOLAR ENERGY↗
DOE OSTI2024

Harnessing Quantum Capacitance in 2D Material/Molecular Layer Junctions for Novel Electronic Device Functionality

Two-dimensional (2D) materials promise advances in electronic devices beyond Moore’s scaling law through extended functionality, such as non-monotonic dependence of device parameters on input parameters. However, the robustness and performance of effects like negative differential resistance (NDR) and anti-ambipolar behavior have been limited in scale and robustness by relying on atomic defects and complex heterojunctions. In this paper, we introduce a novel device concept that utilizes the quantum capacitance of junctions between 2D materials and molecular layers. We realized a variable capacitance 2D molecular junction (vc2Dmj) diode through the scalable integration of graphene and single layers of stearic acid. The vc2Dmj exhibits NDR with a substantial peak-to-valley ratio even at room temperature and an active negative resistance region. The origin of this unique behavior was identified through thermoelectric measurements and ab initio calculations to be a hybridization effect between graphene and the molecular layer. The enhancement of device parameters through morphology optimization highlights the potential of our approach toward new functionalities that advance the landscape of future electronics.

2D materials↗
DOE OSTI2022

Improving the performance of PM6 donor polymer by random ternary copolymerization of BDD and DTBT segments

Developing high-performance wide bandgap polymer donors to match the rapidly growing non-fullerene small molecule acceptors (NF-SMAs) is of great importance to further improve the photovoltaic performances of organic solar cells (OSCs). PM6 and D18 are two leading wide bandgap donor polymers, but their performances are highly sensitive to the molecular weights, which have distinct impact on the morphology and thereby the charge generation and recombination processes. Here, in this work, we reported the random ternary copolymerization of PM6 and D18 segments to develop random terpolymers with finely tuned photoelectronic properties and optimized blend morphology for high-performance OSCs. The resulting random terpolymers (PMD-5, PMD-10, PMD-15 and PMD-20) exhibited finely tuned absorptions, energy levels and blend morphology. The optimal morphology of PMD-15:L8-BO contributed to the fast exciton diffusion and dissociation, efficient charge extraction with suppressed recombination. Thus, the power conversion efficiency was improved from 17.22% of the control PM6 devices and 17.47% of the control D18 devices to 18.12% of PMD-15 based devices, which is the top performance of random terpolymers. Moreover, the PMD-15 exhibited much higher batch-to-batch reproducibility at a broad molecular weight range than that of PM6 and D18, showing promising for practical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Optimizing spectral and morphological match of nonfullerene acceptors toward efficient indoor organic photovoltaics with enhanced light source adaptability

High-performance indoor organic photovoltaics (IOPV) require large-bandgap material systems to absorb visible light efficiently and reduce energy loss. However, state-of-the-art non-fullerene acceptors (NFAs) have absorptions in the near-infrared region and are thus not suitable for IOPV applications. Herein, we report a series of large-bandgap (>1.70 eV) NFAs named FCC-Cl-C8, FCC-Cl-4Ph and FCC-Cl-6Ph by modifying the alkyl side chains with alkylphenyl chains partially or completely. Results show that the bulky alkylphenyl side chains can finely tune the absorption properties of the NFAs and also affect their morphological properties. Interestingly, the best-performing NFA is the one (named FCC-Cl-4Ph) with partial alkyl and alkylphenyl substitutions, which blue-shift the absorption of the NFAs while minimizing the negative morphological effect of the bulky alkylphenyl chains. As a result, FCC-Cl-4Ph can achieve excellent indoor efficiencies over 29% under a 3000 K LED lamp at 1000 lux and show better solution processability over FCC-Cl-C8. More importantly, FCC-Cl-4Ph can maintain high indoor performance (29.7–26.8% at 1000 lux) under a wide range of indoor lighting spectra (2600, 3000, 4000, and 6500 K LED lamps), which should be due to the blue-shifted spectra of FCC-Cl-4Ph and better matching with various indoor conditions. Finally, this work reveals an interesting structure-property relationship and offers useful strategies for the further design of NFAs toward efficient IOPV devices.

14 SOLAR ENERGY↗
DOE OSTI2022

Tradeoff between Intermolecular Interaction and Backbone Disorder by High Molecular Dipole Block for Improving Blend Morphology of Polymer Solar Cells

Constructing terpolymer has attracted increasing attention as a strategy to improve the performance of polymer solar cell. Terpolymer usually offers an opportunity to lower the frontier molecular orbital energy level, introduces additional absorption band and sometimes optimizes the morphology of the active blend. Generally, the additional segment in terpolymer backbone inevitably introduces backbone disorder, which causes entropy rises. However, selecting a suitable dipole unit introduces extra driving forces for crystallization by enhancing intermolecular interactions. This provides a handy knob for tradeoff between intermolecular interaction and backbone disorder, thus regulating the blend morphology. In this study, a high dipole and electron-deficient group of pyrrolo[3,4-f ]benzotriazole-5,7(6H)-dione (TzBI) is incorporated into the high-performance donor polymer and a series of terpolymers with different content of TzBI are designed. As expected, the morphology is optimized gradually for improving charge generation and charge transport, also suppressing charge recombination. The champion device with 10% TzBI exhibited a power conversion efficiency (PCE) of 18.36%, which is 5% increase compared to the controlled device. This study presents a charming terpolymer strategy by highly electron-deficient and high dipole segment to realize a tradeoff between intermolecular interaction and backbone disorder, facilitating the optimization of morphology and elevation of fill factor and device efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Developing Efficient Benzene Additives for 19.43% Efficiency of Organic Solar Cells by Crossbreeding Effect of Fluorination and Bromination

Employing volatile solid additives have emerged as a promising method to optimize the morphology and improve the performance of organic solar cells (OSCs). However, principles governing the efficient design of solid additives remain elusive. In this work, the programmed fluorination and/or bromination on benzene core to develop efficient additives for OSCs is reported. The programmed fluorination and/or bromination endow the five halogen benzene derivatives, 1,3,5-trifluorobenzene, hexafluorobenzene, 1,3,5-tribromo-2,4,6-trifluorobenzene (TFTB), 1,3,5-tribromobenzene, and hexabromobenzene, with different melting and boiling points, volatility, as well as interactions with the host blend. Studies indicate that the additives with extremely high and low volatility are almost powerless and even detrimental to the morphology evolution. Among them, the combination of fluorine and bromine atoms on TFTB not only enables the more appropriate m.p./b.p. and volatility, but also exerts stronger molecular interactions with the host blend, giving rise to higher ordered molecular packing and more favorable morphology. Importantly, TFTB exhibits good universality to optimize the performances of OSCs with high power conversion efficiencies (PCEs; over 18%) in a group of binary blend systems, and an impressive PCE of 19.43% in the ternary PBTz-F:PM6:L8-BO system.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Smartly Optimizing Crystallinity, Compatibility, and Morphology for Polymer Solar Cells by Small Molecule Acceptor with Unique 2D-EDOT Side Chain

A desired morphology is essential for achieving efficient polymer solar cells. Donors and acceptors with appropriate crystallization can lead to a suitable phase-separated morphology for effective photocurrent generation process. Inspired by the success of Y6 acceptors and the 2D side chain engineering on popular polymer donors and small molecule acceptors, the usage of unique 2D 3,4-ethylene dioxythiophene (EDOT) side chains on Y6 to regulate its crystallinity, compatibility, and thus the related blend morphology is explored. Here, in this study, two molecules of BTP-EDOT-4F and BTP-EDOT-4Cl with such unique 2D EDOT side chains are designed and synthesized. Due to the advantage of EDOT side chain, when these molecules are blended with PM6, the decent power conversion efficiencies (PCEs) of 16.78% and 15.87% are obtained. Furthermore, BTP-EDOT-4F is selected as the third component and added into PM6:L8-BO binary system to form ternary blends. The optimized crystallinity, compatibility, and morphology of such ternary blend are discovered in the presence of BTP-EDOT-4F, which enables efficient exciton dissociation and charge transport as well as decreased recombination, resulting in higher short circuit current density (J sc ) and fill factor. Finally, the outstanding PCE of 18.56% is achieved in ternary blends containing PM6, L8-BO, and BTP-EDOT-4F.

2D EDOT side chains↗
DOE OSTI2023

Ni/CeO 2 Nanocatalysts with Optimized CeO 2 Support Morphologies for CH 4 Oxidation

Catalytic oxidation of CH 4 over nonprecious Ni/CeO 2 catalysts has attracted wide attention. Controlling the morphology of a CeO 2 support can enhance the CH 4 oxidation activity without changing the catalyst composition. Here, in this paper, a series of 2 wt % Ni/CeO 2 nanocatalysts with different CeO 2 support morphologies (nanoparticles (P), rods (R), cubes (C)) and synthetic procedures (precipitation, sol-gel (SG)) were evaluated for their CH 4 oxidation performance. The redox properties of CeO 2 supports and corresponding Ni loaded catalysts were characterized by H 2 -temperature-programmed reduction and oxygen storage capacity (OSC) measurements. The relationship among the CeO 2 morphologies, surface areas, redox properties, and CH4 oxidation activity for both CeO 2 supports and Ni/CeO 2 catalysts was established. The findings suggest that CeO 2 -R has a greater amount of surface oxygen vacancies as well as an improved OSC and CH4 oxidation activity compared to CeO 2 -P and CeO 2 -C supports. The same CH 4 oxidation activity pattern was observed for the Ni containing catalysts (Ni/CeO 2 -R > Ni/CeO 2 -P > Ni/CeO 2 -C). Increasing the CeO 2 surface area by using a sol-gel synthesis method (CeO 2 -SG) improved the amount of surface oxygen vacancies and CH 4 oxidation performance of CeO 2 -SG and Ni/CeO 2 -SG compared to CeO 2 -R and Ni/CeO 2 -R, respectively. Finally, all studied Ni/CeO 2 nanocatalysts showed improved hydrothermal stability compared to conventional Pd/Al 2 O 3 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Over 31% efficient indoor organic photovoltaics enabled by simultaneously reduced trap-assisted recombination and non-radiative recombination voltage loss

Indoor organic photovoltaics (OPVs) have shown great potential application in driving low-energy-consumption electronics for the Internet of Things. There is still great room for further improving the power conversion efficiency (PCE) of indoor OPVs, considering that the desired morphology of the active layer to reduce trap-assisted recombination and voltage losses and thus simultaneously enhance the fill factor (FF) and open-circuit voltage for efficient indoor OPVs remains obscure. Herein, by optimizing the bulk and interface morphology via a layer-by-layer (LBL) processing strategy, low leakage current and low non-radiative recombination loss can be synergistically achieved in PM6:Y6-O based devices. Detailed characterizations reveal the stronger crystallinity, purer domains and ideal interfacial contacts in the LBL devices compared to their bulk-heterojunction (BHJ) counterparts. The optimized morphology yields a reduced voltage loss and an impressive FF of 81.5%, and thus contributes to a high PCE of 31.2% under a 1000 lux light-emitting diode (LED) illumination in the LBL devices, which is the best reported efficiency for indoor OPVs. Additionally, this LBL strategy exhibits great universality in promoting the performance of indoor OPVs, as exemplified by three other non-fullerene acceptor systems. Finally, this work provides guidelines for morphology optimization and synergistically promotes the fast development of efficient indoor OPVs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Improving Miscibility of Polymer Donor and Polymer Acceptor by Reducing Chain Entanglement for Realizing 18.64 % Efficiency All Polymer Solar Cells

All-polymer solar cells have experienced rapid development in recent years by the emergence of polymerized small molecular acceptors (PSMAs). However, the strong chain entanglements of polymer donors (P D s) and polymer acceptors (P A s) decrease the miscibility of the resulting polymer mixtures, making it challenging to optimize the blend morphology. Herein, we designed three P A s, namely PBTPICm-BDD, PBTPICγ-BDD and PBTPICF-BDD, by smartly using a BDD unit as the polymerized unit to copolymerize with different Y-typed non-fullerene small molecular acceptors (NF-SMAs), thus achieving a certain degree of distortion and giving the polymer system enough internal space to reduce the entanglements of the polymer chains. Such effects increase the chances of the P D being interspersed into the acceptor material, which improve the solubility between the P D and P A . The PBTPICγ-BDD and PBTPICF-BDD displayed better miscibility with PBQx-TCl, leading to a well optimized morphology. As a result, high power conversion efficiencies (PCEs) of 17.50 % and 17.17 % were achieved for PBQx-TCl : PBTPICγ-BDD and PBQx-TCl : PBTPICF-BDD devices, respectively. In conclusion, with the addition of PYFT-o as the third component into PBQx-TCl : PBTPICγ-BDD blend to further extend the absorption spectral coverage and finely tune microstructures of the blend morphology, a remarkable PCE of 18.64 % was realized finally.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Improving Cycling Performance of Anode-Free Lithium Batteries by Pressure and Voltage Control

The anode-free lithium (Li) batteries (AFLBs) have great potential to provide higher energy density than most other batteries. However, the performance of AFLBs is very sensitive to pressure and other operating parameters, especially for coin cells widely used in AFLB investigations. Therefore, optimizing cell assembly parameters and test protocol is critical to get reliable and comparable results in this field. In this work, the operating voltage range of AFLBs using a localized high concentration electrolyte has been optimized. The morphology of the deposited Li in AFLBs is much more indicting to the pressure than other type of batteries due to the absence of anode active material (i.e. Li) as a pressure cushion layer in the as prepared cells. With an optimized cycling protocol, a thin layer of uniform nucleation sites can be formed in the initial cycle which will facilitate smooth Li desposition/stripping in the subsequent cycles of AFLBs. The solid electrolyte interphase layer formed under optimized pressure and uniform pressure distribution exhibits a good mechanical stability even after long-term cycling. In conclusion, with an optimized cell configuration, the internal pressure in the coin cells has been optimized to improve the cycling performance of AFLBs (Cu||NMC811) with 72% of capacity retention in 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2021

Urban cells: Extending the energy hub concept to facilitate sector and spatial coupling

The rapid growth of urban areas and concerns over climate change make it vital to improve the energy sustainability of cities. Understanding the complex interactions within different sectors (sectoral) and localities (spatial) of cities plays a crucial role in improving efficiency and sustainability, which is extremely challenging due to the complex urban morphology. State-of-the-art energy concepts do not facilitate a detailed consideration of both sectoral and spatial coupling that energy infrastructure maintains at the urban scale. This has become a significant challenge when designing interconnected urban energy infrastructure. The Urban Cell concept is introduced to address this bottleneck. A novel computational model using a modular approach is introduced to create an interconnected urban infrastructure, including the energy, building, and transportation sectors. Optimal sizing of the distributed energy system (including renewables, energy storage, and dispatchable sources) and optimal urban morphology is determined within a modular unit. A game-theoretic approach is used to model the interactions between urban cells (modular units). The study revealed that the urban cell concept can reduce the net present value of the interconnected energy infrastructure by 37% while increasing the installed renewable energy capacity by 25%. This demonstrates the benefit potential of urban cells and the importance of considering interactions between different sectors and different parts within a city. The Urban Cell concept can be used to present the complex interactions maintained within a city.

Perera, ATD↗
DOE OSTI2024

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enhance the performance of organic solar cells by nonfused ring electron acceptors bearing a pendent perylenediimide group

A new nonfused ring electron acceptor PDI-DO-2F is designed and synthesized by attaching perylenediimide (PDI) unit as a pendent group to the central donor core. Compared with the control molecule DO-2F, the introduction of PDI lateral substituent can greatly enhance the solubility and decrease the crystallinity of the resulted acceptor. The PBDB-T:PDI-DO-2F blend film exhibits a much better morphology with higher and more balanced carrier mobility in contrast to PBDB-T:DO-2F one. PDI-DO-2F based organic solar cells (OSCs) give a power conversion efficiency (PCE) of 11.78%, higher than DO-2F based ones (9.82%). Furthermore, PDI-DO-2F based OSCs shows a ΔE non-rad value of 0.23 eV, which is significantly lower than the DO-2F based ones (0.28 eV). More importantly, the addition of PDI-DO-2F as the third component to the PBDB-T:DO-2F binary system can optimize the morphology of blend films and improve the shelf stability of devices. Finally, the PBDB-T:DO-2F:PDI-DO-2F based ternary OSCs achieve a higher PCE of 13.82%.

14 SOLAR ENERGY↗
DOE OSTI2024

Developing Benzodithiophene-Free donor polymer for 19.36% efficiency Green-Solvent-Processable organic solar cells

Here, in this work, a newly benzodithiophene-free D-A polymer donor, named PDTP-BDD, was developed for realizing green-solvent processed high-performance OSCs. By bridging two electron-rich unit of dithieno[3,2-b:2',3'-d]pyridin-5(4H)-one (DTP) and electron-deficient benzo[1,2-c:4,5c']dithiophene-4,8-dione (BDD) with thiophene units, PDTP-BDD possesses high absorption in the short wavelength range and a deep HOMO energy level. The rigid building blocks also make PDTP-BDD has strong aggregation and poor solubility in common halogen-free solvents (such as o-xylene) at room temperature, but it is readily dissolved and disaggregated at high temperature (120 °C). After cooling down to a lower temperature (60 °C), PDTP-BDD self-assembled and pre-aggregated slowly in the solution at a long time. By employing a delayed processing strategy in the layer-by-layer processed OSCs (LbL-OSCs), an optimized fibril network of the underling layer was realized, enabling the permeation of acceptor into the donor network. The optimized PDTP-BDD/L8-BO-based LbL-OSCs realized a high PCE of 18.42 %. By adding a small amount of D18 to further optimize the PDTP-BDD fibril network, an impressive PCE of 19.36 % was achieved finally in the resulting ternary LbL-OSCs, which is the highest value for OSCs processed by halogen-free solvents.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Binary Blend All‐Polymer Solar Cells with a Record Efficiency of 17.41% Enabled by Programmed Fluorination Both on Donor and Acceptor Blocks

Abstract Despite remarkable breakthrough made by virtue of “polymerized small‐molecule acceptor (PSMA)” strategy recently, the limited selection pool of high‐performance polymer acceptors and long‐standing challenge in morphology control impede their further developments. Herein, three PSMAs of PYDT‐2F, PYDT‐3F, and PYDT‐4F are developed by introducing different fluorine atoms on the end groups and/or bithiophene spacers to fine‐tune their optoelectronic properties for high‐performance PSMAs. The PSMAs exhibit narrow bandgap and energy levels that match well with PM6 donor. The fluorination promotes the crystallization of the polymer chain for enhanced electron mobility, which is further improved by following n ‐doping with benzyl viologen additive. Moreover, the miscibility is also improved by introducing more fluorine atoms, which promotes the intermixing with PM6 donor. Among them, PYDT‐3F exhibits well‐balanced high crystallinity and miscibility with PM6 donor; thus, the layer‐by‐layer processed PM6/PYDT‐3F film obtains an optimal nanofibril morphology with submicron length and ≈23 nm width of fibrils, facilitating the charge separation and transport. The resulting PM6/PYDT‐3F devices realizes a record high power conversion efficiency (PCE) of 17.41% and fill factor of 77.01%, higher than the PM6/PYDT‐2F (PCE = 16.25%) and PM6/PYDT‐4F (PCE = 16.77%) devices.

Zhou, Dehong↗