Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mixtures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

DME-to-Propane Mixture Effects on a Light Duty Compression Ignition Engine

Fuels that can be produced in a sustainable manner are of high interest because they can provide an essential step toward net zero emissions vehicles. This study examines the combustion of two such fuels, Dimethyl Ether (DME) and propane, in a compression ignition, 4-cylinder, 2.2L engine running with mixtures of DME-to-Propane ranging of 100%-0%, 85%-15%, 75%-25%, and 65%-35% by weight. Testing was conducted at 2000rpm - 100Nm, an important representative point in the FTP certification cycle. For each fuel mixture, conditions tested include sweeps of boost, EGR and injection pressure. Here, tests are mainly conducted at a constant combustion timing with CA10 of -1 deg with respect to TDC, with an engine controller combustion feedback system based on in-cylinder sampling of pressure. Trends of NOx, HC, and CO are similar for the range of DME-to-propane, from 100%-0% to 75%-25%. Boost and injection pressures had the most notable impact on the heat release traces. Higher boost, from stoichiometric to lean resulted in approximately a 3-5% increase on cycle efficiency. Fuel injection pressures resulted in about 1% gain per 200bar. Results also illustrated that EGR is effective in reducing NOx but causes notable degradation of cycle efficiency. The emissions for DME-propane mixtures with 65%-35% had a different trend, with CO and HC exceeding the runs with lower propane content by 2 to 3-fold. As propane content increases, the pressure rise rates become higher, and with 65%-35% mixtures, rates easily exceed 12bar/deg. The increased rise rates correlate with early injection timings but the rates can be reduced, with higher boost and lower injection pressures. The result of the approach, however, leads to lower thermal efficiencies, decreasing efficiency by over 5% between neat DME and the highest propane ratios.

Combustion and combustion processes↗
DOE OSTI2024

Private, public, and bottled drinking water: Shared contaminant-mixture exposures and effects challenge

Background: Humans are primary drivers of environmental–contaminant exposures worldwide, including in drinking-water (DW). In the United States, point-of-use DW (POU–DW) is supplied via private tapwater (TW), public-supply TW, and bottled water (BW). Differences in management, monitoring, and messaging and lack of directly–intercomparable exposure data influence the actual and perceived quality and safety of different DW supplies and directly impact consumer decision–making. Objectives: The purpose of this paper is to provide a meta-analysis (quantitative synthesis) of POU–DW contaminant–mixture exposures and corresponding potential human–health effects of private-TW, public-TW, and BW by aggregating exposure results and harmonizing apical–health–benchmark–weighted and bioactivity–weighted effects predictions across previous studies by this research group. Discussion: Simultaneous exposures to multiple inorganic and organic contaminants of known or suspected human-health concern are common across all three DW supplies, with substantial variability observed in each and no systematic difference in predicted cumulative risk between supplies. Differences in contaminant or contaminant–class exposures, with important implications for DW–quality improvements, were observed and attributed to corresponding differences in regulation and compliance monitoring. Conclusion: The results indicate that human-health risks from contaminant exposures are common to and comparable in all three DW–supplies, including BW. Importantly, this study’s target analytical coverage, which exceeds that currently feasible for water purveyors or homeowners, nevertheless is a substantial underestimation of the breadth of contaminant mixtures in the environment and potentially present in DW. Thus, the results emphasize the need for improved understanding of the adverse human-health implications of long-term exposures to low–level inorganic–/organic–contaminant mixtures across all three distribution pipelines and do not support commercial messaging of BW as a systematically safer alternative to public-TW. Regardless of the supply, increased public engagement in source-water protection and drinking–water treatment is necessary to reduce risks associated with long-term DW–contaminant exposures, especially in vulnerable populations, and to reduce environmental waste and plastics contamination.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Adsorption Equilibrium, Kinetics, and Column Breakthrough Data for Aqueous Solutions of Binary-Acid and Ternary-Acid Mixtures of Acetic Acid, Butyric Acid, and Lactic Acid on IRN-78 Ion-Exchange Resin at Initial pH Levels of ∼3–7 and at 25–55 °C

This work is part of an effort to develop thermophysical property data and models supporting adsorptive process development for organic acid separation from a dilute aqueous solution of fermentation broth. It presents systematic experimental measurements for aqueous-phase adsorption equilibrium, kinetics, and column breakthrough for three binary-acid aqueous mixtures (acetic acid + lactic acid, butyric acid + lactic acid, and acetic acid + butyric acid) and one ternary-acid aqueous mixture (acetic acid + butyric acid + lactic acid) on Amberlite IRN-78 ion-exchange resin. The equilibrium measurements covered broad ranges of the initial acid concentration (100–400 mmol/L), initial pH (∼3–7), and temperature (25–55 °C). The equilibrium data for the binary-acid and ternary-acid aqueous mixtures indicate selective adsorption of lactic acid at initial pH levels of ∼3 and 4, while acetic acid and butyric acid are selectively adsorbed at initial pH levels of 5, 6, and 7. The subsequent kinetics and column breakthrough experiments were performed at 200 mmol/L with equimolar ratios, an initial pH of 6, and 25 °C. In conclusion, the measurements provide essential data sets for rigorous thermodynamic modeling and process simulation of adsorptive separation processes for organic acid separation from fermentation broth.

Adsorption↗
DOE OSTI2025

Scaling Field-Theoretic Simulation for Multicomponent Mixtures with Neural Operators

Multicomponent polymer mixtures are ubiquitous in biological self-organization but are notoriously difficult to study computationally. Plagued by both slow single molecule relaxation times and slow equilibration within dense mixtures, molecular dynamics simulations are typically infeasible at the spatial scales required to study the stability of mesophase structure. Polymer field theories offer an attractive alternative, but analytical calculations are only tractable for mean-field theories and nearby perturbations, constraints that become especially problematic for fluctuation-induced effects such as coacervation. Here, we show that a recently developed technique for obtaining numerical solutions to partial differential equations based on operator learning, neural operators, lends itself to a highly scalable training strategy by parallelizing per-species operator maps. We illustrate the efficacy of our approach on six-component mixtures with randomly selected compositions and that it significantly outperforms the state-of-the-art pseudospectral integrators for field-theoretic simulations, especially as polymer lengths become long.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Diffusion of Atoms in Glassy Mixtures of Deuterium and Lithium

The diffusion coefficients of D and Li were calculated in amorphous, glassy Li+D mixtures for various concentrations of D in lithium over the temperature range 100–1000 K. The densities of the mixtures as a function of temperature were also determined. The diffusion coefficients were obtained by the analysis of the mean-squared displacement using molecular dynamics with ReaxFF, a reactive force field. In conclusion, the diffusion and density data obtained for Li+D mixtures were compared with the available experimental and calculated data reported in the literature.

Diffusion↗
DOE OSTI2026

Solubilization of PET in binary mixtures of HFIP and DCM

The dissolution of polyethylene terephthalate (PET) is a critical step for a solvent-based process, yet it typically requires highly corrosive or toxic solvents. Here, we investigate the solubilization and conformational behavior of PET in binary mixtures of hexafluoro-2-propanol (HFIP) and dichloromethane (DCM) as a strategy to reduce HFIP usage while maintaining effective dissolution. Small-angle neutron scattering (SANS) measurements reveal that PET remains molecularly dissolved in HFIP/DCM mixtures up to 50 vol% DCM. Analysis of PET chain conformations shows a transition from Gaussian behavior at low HFIP fractions to more swollen chains at intermediate compositions, accompanied by a counter-intuitive minimum in the radius of gyration at 50% HFIP. Complementary SANS measurements of the binary solvents demonstrate that compositional heterogeneity is maximized at this same solvent composition, suggesting a direct coupling between solvent microstructure and polymer dimensions. Molecular dynamics simulations corroborate the experimental findings, revealing solvent domain formation, preferential solvation of PET by HFIP, and a “caging” effect arising from solvent heterogeneity that leads to polymer coil compaction. Together, these results provide molecular-level insight into polymer behavior in mixed solvent systems and establish HFIP/DCM mixtures as a promising, more sustainable solvent platform for the PET post-process.

Arifuzzaman, Arif [ORNL]↗
DOE OSTI2025

Thermodynamic consistency and fluctuations in mesoscopic stochastic simulations of reactive gas mixtures

It is essential that mesoscopic simulations of reactive systems reproduce the correct statistical distributions at thermodynamic equilibrium. By considering a compressible fluctuating hydrodynamics (FHD) simulation method of ideal gas mixtures undergoing reversible reactions described by the chemical Langevin equations, we show that thermodynamic consistency in reaction rates and the use of instantaneous temperatures for the evaluation of reaction rates is required for fluctuations for the overall system to be correct. We then formulate the required properties of a thermodynamically consistent reaction (TCR) model. As noted in the literature, while reactions are often discussed in terms of forward and reverse rates, these rates should not be modeled independently because they must be compatible with thermodynamic equilibrium for the system. Using a simple TCR model where each chemical species has constant heat capacity, we derive the explicit condition that the forward and reverse reaction rate constants must satisfy in order for the system to be thermodynamically consistent. We perform equilibrium and non-equilibrium simulations of ideal gas mixtures undergoing a reversible dimerization reaction to measure the fluctuational behavior of the system numerically. We confirm that FHD simulations with the TCR model give the correct static structure factor of equilibrium fluctuations. For the statistically steady simulation of a gas mixture between two isothermal walls with different temperatures, we show using the TCR model that the temperature variance agrees with the corresponding thermodynamic-equilibrium temperature variance in the interior of the system, whereas noticeable deviations are present in regions near walls, where chemistry is far from equilibrium.

Polimeno, Matteo [University of California, Merced↗
DOE OSTI2026

Mathematical Models and Numerical Methods for High-Fidelity Simulation of Ignition of Reactive Mixtures by Nanosecond Plasma Discharges in Realistic Configurations

We present a newly developed framework for the numerical simulation of ignition of reactive mixtures using single or repeated nanosecond discharge pulses. The framework builds upon the AMReX library, using the existing compressible solver PeleC and low-Mach solver PeleLMeX and allowing for adaptive mesh refinement, complex geometries, and execution on next-generation high-performance computing (HPC) systems. High-fidelity elementary models are adopted for weakly-ionised plasma discharges with significant energy deposition, consistent with nanosecond discharge pulses, and then implemented in the solver. The treatment of non-thermal electrons and charged species, thermodynamics of non-equilbrium species, plasma kinetics, limiting time scales, and boundary conditions for charged species are discussed and addressed for computational efficiency. The framework is demonstrated for three relevant applications: single and multi-pulse discharges in air, single pulse ignition of an ethylene/air mixture, and a three-dimensional plasma discharge in air with temperature stratification. The successful application of the framework demonstrates the feasibility of high-fidelity simulation of ignition of air/hydrocarbon mixtures in three-dimensions with multiple discharge pulses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

AUTOIGNITION DELAY TIMES FOR REFORMATE GAS MIXTURES FROM METHANE GAS ENGINES

Methane slip is a prominent issue in natural gas reciprocating engines that are used in transportation and marine applications. The incomplete combustion that results in methane slip can be resolved with the introduction of hydrogen within the combustion mixture to improve methane oxidation and further enable combustion within the engine crevices where methane has previously remained unreacted. Steam methane reforming (SMR) is a common method used to produce hydrogen and can be used to design an onboard device to reduce methane slip from reciprocating engines. The development of this reformer device requires the validation of high-fidelity chemical kinetic models at the low temperatures of the crevice volumes of these engines. In this work, auto-ignition data is obtained using a shock tube at lean (φ—0.714 or λ—1.4) and stoichiometric (φ, λ = 1) equivalence ratios spanning a temperature range of 1042–1234 K at the 80-bar operating pressure of the test engine. Blends of methane, hydrogen, and reformate products from the SMR reaction are shock-heated in synthetic air, with the ignition delay time measured using an OH* chemiluminescence detector at 310 nm and a CH* detector at 430 nm. The experimental results are compared to several state-of-the-art chemical kinetic mechanisms from the literature. In general, most of the mechanisms show very good agreement with experiments at higher temperatures, with simulation results showing little deviation from experiments at lower temperatures. A sensitivity analysis was conducted, and the results reveal that the reaction H2 + CH3O2 = H + CH3O2H has a very significant role in determining low-temperature ignition delay times (IDTs) of SMR mixtures. These findings provide valuable insights into the chemical kinetics governing methane reformate combustion and contribute to the optimization of onboard reformer designs aimed at mitigating methane slip in natural gas-fueled engines.

Fraze, Matthew↗
DOE OSTI2024

Oxygen Limit for Flammability of a Gas Mixture of Helium – Hydrogen – Oxygen in the U.S. Department of Energy Standard Canister

The radiolytic breakdown of residual free, physisorbed, and chemisorbed waters is anticipated in the sealed dry storage of spent nuclear fuel (SNF), releasing H 2 gas into the initial cover gas of helium. For aluminum-clad SNF (ASNF) in particular, the expected total hydrogen in the canister is enough to dominate the cover gas mixture if fully released, and based on experimental rates of H 2 generation, H 2 percentages exceeding the lower flammability limit appear likely. However, no evidence of radiolytic generation of O 2 has been observed to date, so the potential for flammability is averted due to the lack O 2 . Lack of oxygen has been credited for avoiding flammability in some existing storage and transportation approaches for SNF and other waste. This report reviews literature on flammability limits with a focus on the limiting oxygen concentration to provide technical underpinnings to refine a flammability criterion for gas mixtures of helium, hydrogen, and oxygen where the oxygen is expected to be the limiting species. While there is general consensus on H 2 flammability limits at standard temperature and pressure, the decay heat and gas generation within ASNF sealed dry storage canisters could push them to elevated temperatures and pressures, so the goal is to identify an oxygen threshold that will bound the behavior over the temperature and pressure range of the U.S. Department of Energy (DOE) Standard Canister. The information reviewed in this document supports the criterion that the oxygen concentration in a He-H 2 -O 2 mixture should be less than 1.5% to avoid flammability at temperatures and pressures relevant to sealed dry storage of ASNF in the DOE Standard Canister, i.e., up to 343°C (650°F) and 500 psig, respectively. Note that while data covering the full range of temperature at atmospheric pressure and nearly the full range of pressure at room temperature were available, data for the combined effects was available only at moderate temperatures and pressures; the recommended 1.5% O 2 threshold is based on the breadth of available data reported here and apparent trends therein.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Evaluating Lithium-Lead Mixtures for Increased Tritium Breeding in Fusion Energy Blanket Systems: Exploring the Impact of Composition and Temperature

This project investigates hypo- and hyper-eutectic liquid lithium-lead (PbLi) mixtures as a coolant in fusion blanket systems, with a focus on testing the compatibility of compositions with better tritium breeding ratios (TBR). The 12-month study concentrates on static corrosion experiments, comparing silicon carbide (SiC) corrosion rates in Li-rich and eutectic Li-Pb mixtures, and examining interactions between Mo and PbLi. The research seeks to determine the maximum operating temperatures for this material combination, acknowledging the balance between Li-Pb melting temperature and achievable TBR to unlock new opportunities for blanket design. This work lays the groundwork for future collaboration between Kyoto Fusioneering and Oak Ridge National Laboratory (ORNL). Findings could enhance the TBR of fusion blanket designs, and impact fusion energy development by confirming material compatibility between different Li-Pb mixtures with SiC and Mo at higher temperatures, including at temperatures relevant for very high-temperature blankets (1,000 °C), which could enable higher electricity conversion efficiencies and commercial applications using process heat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Calculation of monomer yields, verification of PG concentration approximation, catalyst comparison for neat aromatic RCF, SEM micrographs for postreaction pulps, yields of aqueous-phase sugar derivatives after PG-H2O RCF, reactor pressure transients, GPC comparing pre- and postreaction organic solvent composition, PG-H2O miscibility testing, GPC probing dimer/oligomer fractionation in PG-H2O mixtures for

Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents.

biorefining↗
DOE OSTI2024

Efficient Leaching of Metal Ions from Spent Li-Ion Battery Combined Electrode Coatings Using Hydroxy Acid Mixtures and Regeneration of Lithium Nickel Manganese Cobalt Oxide

Extensive use of Li-ion batteries in electric vehicles, electronics, and other energy storage applications has resulted in a need to recycle valuable metals Li, Mn, Ni, and Co in these devices. In this work, an aqueous mixture of glycolic and lactic acid is shown as an excellent leaching agent to recover these critical metals from spent Li-ion laptop batteries combined with cathode and anode coatings without adding hydrogen peroxide or other reducing agents. An aqueous acid mixture of 0.15 M in glycolic and 0.35 M in lactic acid showed the highest leaching efficiencies of 100, 100, 100, and 89% for Li, Ni, Mn, and Co, respectively, in an experiment at 120 °C for 6 h. Subsequently, the chelate solution was evaporated to give a mixed metal-hydroxy acid chelate gel. Pyrolysis of the dried chelate gel at 800 °C for 15 h could be used to burn off hydroxy acids, regenerating lithium nickel manganese cobalt oxide, and the novel method presented to avoid the precipitation of metals as hydroxide or carbonates. The Li, Ni, Mn, and Co ratio of regenerated lithium nickel manganese cobalt oxide is comparable to this metal ratio in pyrolyzed electrode coating and showed similar powder X-ray diffractograms, suggesting the suitability of α-hydroxy carboxylic acid mixtures as leaching agents and ligands in regeneration of mixed metal oxide via pyrolysis of the dried chelate gel.

Electrochemistry↗
DOE OSTI2025

Hydrochlorination of Uranium Dioxide in a Molten Salt Mixture - Phase 1: Tube Furnace Cross Flow Experiments

In 2023, Metatomic® Inc., a South Carolina based company, was awarded a Gateway for Advanced Innovation in Nuclear (GAIN) research voucher for a proposed series of experiments aimed at demonstrating the viability of a spent nuclear fuel (SNF) recycling process patented by Met atomic® Inc. For the GAIN voucher, Metatomic® Inc. selected Savannah River National Laboratory (SRNL) as a partner in executing the proposed proof-of-concept experiments. This report outlines the proof-of-concept experiments performed by SRNL for Metatomic® Inc. during Phase 1 (of 2) experimentation. The Phase 1 hydrochlorination experiments consisted of weighing UO2 into alumina crucibles with a eutectic mixture of NaCl and CsCl, heating the uranium/salt mixture to a varied temperature (550, 650, or 750 °C), and flowing anhydrous hydrogen chloride (AHCl) gas across the surface of the uranium-bearing molten salt mixture. The hydrochlorination process conditions were maintained for 4-5 hours and the percent conversion for each batch of UO2 was determined using a suite of analytical characterization techniques. The degree of UO2 conversion was found to be greatest at the highest tested temperature, ultimately achieving 32.9% conversion of UO2 to water soluble uranium-chloro species (e.g., UO2Cl2, UCl4) after exposure to AHCl for 4.25 hours at 750 °C.

Nguyen, Vinh T. [Savannah River National Laborator↗
DOE OSTI2025

Speed of Sound Measurements of Binary Mixtures of trans -1,2-Difluoroethylene (R-1132(E)) with Difluoromethane (R-32) or 2,3,3,3-Tetrafluoropropene (R-1234yf)

The speed of sound of two binary mixtures containing 0.336 mole fraction trans-1,2- difluoroethylene (R-1132(E)) with difluoromethane (R-32) and 0.435 mole fraction R-1132(E) with 2,3,3,3-tetrafluoropropene (R-1234yf) were measured with a dual-path pulse-echo instrument. The speed of sound was measured along several pseudo-isochores for each blend at temperatures ranging from 230 K to 325 K for blends with R-32 and to 342 K for blends with R- 1234yf. Measurements started at pressures just above each mixtures bubble point pressure and were limited to 8 MPa to avoid potential disproportionation reactions of the R-1132(E). The data were compared to multi-fluid models incorporating Helmholtz-energy-explicit equations of state (EOS) for each pure fluid.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Identifying Green Solvent Mixtures for Bioproduct Separation Using Bayesian Experimental Design

Liquid–liquid extraction (LLE) is a widely used technique for the separation and purification of liquid-phase products with applications in various industries, including pharmaceuticals, petrochemicals, and renewable chemistry. A critical step in the design of an LLE process is the selection of appropriate solvents. This study presents a new methodology for identifying solvent mixtures for bioproduct separation using Bayesian experimental design (BED). Motivated by the need for environmentally friendly and effective separation methods, we address the challenge of selecting solvent systems that balance separation efficiency, selectivity, and environmental impact while also tackling the difficulty of separating multiple bioproducts using complex solvent systems. Our approach specifically seeks to predict product partition coefficients (log10 Kp values) as thermodynamic parameters underlying solvent selection. The iterative approach integrates Bayesian optimization with experimental measurements to guide solvent selection and leverages COSMO-RS simulations to enhance high-throughput experimentation. Using the design of solvent systems for the separation of lignin-derived aromatic products via centrifugal partition chromatography (CPC) as a case study, we show that within seven iterations/cycles of the methodology, we can identify new mixtures of green solvents that align with CPC design principles. Furthermore, these results demonstrate the efficacy of the BED framework in optimizing green solvent systems for complex separations, highlighting the potential of this method to advance the field of green chemistry and contribute to the development of sustainable industrial processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Toward a Generalizable Prediction Model of Molten Salt Mixture Density with Chemistry‐Informed Transfer Learning

Optimally designing applications of molten salts requires knowledge of their thermophysical properties over a wide range of temperatures and compositions. There exist significant gaps in existing databases and this data can be challenging to experimentally measure due to high temperatures, salt corrosivity, and salt hygroscopicity. Existing databases have been used to create Redlich–Kister (RK) models for mixture density showing improved accuracy with respect to ideal mixing assumptions, but these models require subcomponent data measurements for each new system, therefore lacking generality. In order to address generalizability and data sparsity, a transfer learning procedure is proposed to train deep neural networks (DNNs) using a combination of semi‐empirical relationships (RK), data from the thermophysical arm of the molten salt thermal properties database and universal ab initio properties of component mixtures taken from the joint automated repository for various integrated simulations (JARVIS) classical force‐field inspired descriptors database to predict density in molten salts. Herein, it is shown that DNNs predict molten salt density with an r 2 over 0.99 and a mean absolute percentage error under 1%, outperforming alternative methods.

inorganic materials↗
DOE OSTI2025

Reciprocal Ternary Molten Salts Enable the Direct Upcycling of Spent Lithium‐Nickel‐Manganese‐Cobalt Oxide (NMC) Mixtures to Make NMC 622

Cathode active material is the most valuable component of spent lithium‐ion batteries, accounting for ≈30% of their overall value. Direct recycling of cathode materials involves recovering, regenerating, and reusing them without breaking down their chemical structure. This approach maximizes the added value of the cathode compound and reduces manufacturing costs by avoiding the need for virgin material production. However, one key challenge in scaling direct recycling from lab to industry is the requirement for highly purified cathode materials, contrasting with the low purity of black mass generated from battery shredding. No efficient separation process currently exists to isolate different lithium‐nickel‐manganese‐cobalt oxides (NMCs) from each other. Thus, direct recycling technologies that can operate with mixtures of multiple NMC stoichiometries will be best‐suited for industrial adoption. This study explores the direct recycling of NMC mixtures into NMC 622 using a “reciprocal ternary molten salts (RTMS)” system. Ionothermal relithiation and upcycling within the RTMS system successfully restore the layered structure, lithium content, and electrochemical performance of degraded NMCs, yielding results comparable to pristine NMC 622 (P‐NMC 622).

25 ENERGY STORAGE↗