Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Mechanical Behaviour”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

A comparative analysis of numerical approaches for the description of gas flow in clay-based repository systems: From a laboratory to a large-scale gas injection test

There is nowadays a consensus among many countries that geological disposal is a favourable solution for the long-term management. Although different host formations and different barrier systems are under consideration around the world, clay-based materials form an important component for waste isolation in most national programmes. Hence, a good comprehension of the effect of gas flow on the hydro-mechanical behaviour of clay-based soils is essential, both at laboratory and field scale. Task B under the international cooperative project DECOVALEX-2023 has recently shown that, after some enhancement, models can be employed to reproduce laboratory scale tests, even with different sample geometries 37 . However, further work is required to understand whether they can be applied to simulate a large-scale experiment. Up-scaling of models for the advective transport of gas through clay-based low permeable material presents a number of problems related to the difficulty in obtaining consistent hydrogeological parameters and constitutive relationships at both laboratory and field scale. Based on a unique dataset from a large-scale gas injection test (Lasgit) performed at the Äspö Hard Rock Laboratory (Sweden), Task B within DECOVALEX-2023 has explored the refinement of these numerical strategies applied to the simulation of gas flow. Work performed within the task reveals that codes do not need to be substantially modified from the laboratory models to reproduce full-scale tests: indeed, model parameters calibrated and validated at laboratory scale have been applied to predict field scale gas flow at Lasgit, including peak gas pressure and injected cumulative gas volume. By means of (1) the introduction of interfaces between blocks to reflect the experimental configuration and the (2) adjustment of some parameters (e.g., higher permeability), the updated models are able to represent most of the key features observed in the experimental data, even at a large scale.

Tamayo-Mas, E↗
DOE OSTI2023

Mechanical behavior analysis using small-size graphite disc compression testing with digital image correlation methods

The ASTM International Standard Test Method for Tensile Stress-Strain of Carbon and Graphite (ASTM C749) requires dog-bone shaped specimens. Unfortunately, specimen sizes required in ASTM C749 are much too large for irradiation within a test reactor and are incompatible with irradiation capsule volumes, molten salt degradation facilities, or oxidation apparatus. The ASTM International Standard Test Method for Tensile Strength Estimate by Disc Compression of Manufactured Graphite (ASTM D8289) was developed as an alternative that provides a means for testing tensile properties using smaller specimens when geometric constraints are present. However, the important stress–strain relation throughout the test loading history that could be recorded using ASTM C749 is lost by using ASTM D8289 because of the difficulties involved with using traditional strain gauges or extensometers on such a small specimen. In this work, a digital image correlation (DIC) method, which uses a full-field noncontact surface displacement measurement technique, was applied along with the ASTM D8289 splitting tensile test on eight small samples of graphite grade Mersen 2114 to track their deformation during compressive loading. Initial results showed that the DIC technique can measure the surface displacement/strain on these small (Ø6 × 3 mm) graphite specimens with high accuracy and good repeatability, indicating that the DIC technique, combined with the small-disc splitting tensile test in ASTM D8289, can capture the strain evolution in the test. In conclusion, further comparison of measured strains with analytical and numerical simulation results provides additional understanding of the mechanical behaviour of this nuclear graphite material in complex stress states.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Critical statistical assessment of data in metal additive manufacturing

Obtaining high quality data reflecting the relationships between the additive manufacturing (AM) process parameters, material microstructure and mechanical properties is crucial for the use of machine learning in AM. A database of over 4,000 data entries of metal AM was created thanks to a large number of literature studies on key process parameters and indicators of build quality. Meta-analysis reveals critical biases in the literature. Firstly, majority of studies report only high quality builds, these imbalances in reporting result in weak correlation between process parameters, properties and consolidation, limiting the ability of machine learning models to generalize beyond optimized conditions. Nevertheless, the trained models accurately predict yield strength ($R^2 = 0.85$), suggesting that certain process–property relationships are effectively captured within these models. Secondly, quantitative microstructural data are largely absent, limiting the learning of the microstructure-mechanical properties relationships. Finally, current process window identification is based largely on the consolidation, despite significant uncertainty in its measurement. It is important to identify the process map on the basis of not only the consolidation, but also mechanical behaviour under loading. Such a identification shows that 316 L and Inconel have much larger process map (i.e. highly printable) in comparison to the AlSi10Mg and Ti6Al4V.

Additive manufacturing↗
DOE OSTI2021

Irradiation effects in tungsten—From surface effects to bulk mechanical properties

Advanced materials such as tungsten fibre-reinforced composites allow to overcome severe weaknesses of the baseline materials for plasma-facing components — copper and tungsten. The effect of the fusion environment on the mechanical properties of these materials, e.g. the embrittlement by neutron irradiation, plays a key role for the development of future fusion reactors. To simulate this effect, high-energy ions are used as a substitute for the displacement damage by neutrons. We propose the use of very fine tungsten wire as a possibility of studying the influence of irradiation damage on the mechanical properties. This is possible as they allow full-depth irradiation of almost the entire volume despite the limited penetration depth of ions. Geometrical size effects are mitigated due to the nanoscale microstructure of the wire. In addition, similar wire is used in tungsten fibre-reinforced composites. Thus, the investigation of irradiated wire can directly be used for the prediction of the bulk composite properties. For the proof of this concept tungsten wire with a diameter of 16 μm was electrochemically thinned to 5 μm and irradiated with 20.5 MeV W 6+ ions. The mechanical properties were subsequently determined by macroscopic tensile testing. Irradiation to 0.3, 1 and 9 dpa did not lead to a change of the mechanical behaviour. Both strength and ductility, the latter indicated by the reduction of area, were similar to the as-fabricated state.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Investigation of the temperature-dependent failure processes in PVD Cr-coated ZIRLO nuclear fuel cladding using in situ X-ray micro-tomography imaging

In this work, an accident tolerant fuel cladding system with Cr coating deposited using physical vapour deposition (PVD) method onto commercial Optimized ZIRLO™ was studied. The cladding tubes were machined into C-rings and loaded to failure under compression with real-time synchrotron micro-X-ray computed tomography (XCT) imaging at room temperature (RT), 345 °C, 650 °C and 950 °C in argon (Ar) atmosphere. The mechanical behaviour and failure processes were found strongly temperature-dependent where the Cr coating showed brittle fracture at RT and 345 °C, ductile fracture at 650 °C and a reversion to brittle fracture at 950 °C. Nanoindentation measurements and scanning electron microscopy (SEM) imaging were conducted on the materials after high temperature testing. It was found that recrystallisation of the Cr coating occurred at elevated temperatures, which significantly affected its local properties hence the failure behaviour at different temperatures. This work represents the first in situ 3D XCT observation of progressive failure processes in PVD Cr-coated ZIRLO claddings up to 950 °C providing critical insights into its brittle-to-ductile transition (BDTT) behaviour and subsequent ductile-to-brittle reversion with the increase in temperature. Moreover, results are compared with other PVD Cr-coated Zircaloy materials from open literature; the influences of the coating microstructure and local properties on the failure stress/strain and fracture processes are discussed.

Yuan, Guanjie↗
DOE OSTI2025

Bats flying through a Y-maze are visually attracted to wind turbine surfaces

Wind energy’s rapid expansion has led to unintended consequences for wildlife, with migratory bats among the species most at risk. The behavioural mechanisms underlying collisions remain poorly understood, but one hypothesis is that bats are attracted to wind turbine structures. Vision is important to bat orientation and obstacle avoidance, yet it has been relatively understudied in the context of bat–turbine interactions. We hypothesize that light reflected off turbine surfaces could attract bats, acting as a sensory pollutant that may increase collision risk. To test whether reflective turbine surfaces elicit attraction, we flew 242 Lasiurus cinereus and 154 Lasionycteris noctivagans through Y-maze assays. Bats were at least twice as likely to fly towards white turbine blade sections compared to less reflective black ones. This attraction intensified when the alternative exit was a dark, empty flyway, with 74% of L. cinereus and 97% of L. noctivagans flying towards the white turbine blade. These findings provide evidence that visual sensory pollutants could underlie bat–turbine interactions, and if so, wind turbines could be ecological traps.

17 WIND ENERGY↗
DOE OSTI2024

A multisensory approach to understanding bat responses to wind energy developments

Abstract Millions of bats are killed at wind energy facilities worldwide, yet the behavioural mechanisms underlying why bats are vulnerable to wind turbines remain unclear. Anthropogenic stimuli that alter perceptions of the environment, known as sensory pollution, could create ecological traps and cause bat mortality at wind farms. We review the sensory abilities of bats to evaluate potential stimuli associated with wind farms and examine the role of spatial scale on the perceptual mechanisms of sensory pollutants associated with wind energy facilities. Audition, vision, somatosensation and olfaction are sensory modalities that bats use to perceive their environment, including wind farms and turbine structures, but they will not all be useful at the same spatial scales. Bats most likely use vision to perceive wind farms on the landscape, and obstruction lighting may be the first sensory cue to attract bats to wind farms from kilometres away. Research that assesses the risks posed by specific sensory pollutants, when conducted at the appropriate scale, can help identify solutions to reduce bat mortality, such as determining the attractiveness of obstruction lighting to bats at a landscape scale.

Jonasson, Kristin A.↗
DOE OSTI2024

DECOVALEX-2023: Task D Final Report

Task D of DECOVALEX-2023 is focused on the simulation of the coupled thermal hydraulic-mechanical (THM) behaviour in the full-scale engineered barrier system (EBS). The Horonobe EBS experiment is the demonstration of the full-scale EBS in the underground research laboratory (URL) (performed by JAEA in the Horonobe URL in Japan). Task D consisted of the three steps, a preliminary step (Step 0), simulation of the laboratory tests (Step 1) and simulation of the in-situ full-scale EBS experiment (Step 2). Since the Horonobe EBS experiment demonstrates the vertical emplacement option of the EBS, the experiment gallery is also backfilled with the backfill material. Therefore, interaction between the EBS and the backfill material can also be demonstrated, such as deformation (change of density) of the buffer material. The underground water in the Horonobe URL is saline. This fact adds chemical processes to THM behaviour. For example, mechanical properties (such as swelling pressure of the buffer material and backfill material) and hydraulic properties (such as permeability of the buffer material and backfill material) change depending on the water chemistry. Task D was therefore a challenging Task focused on not only the relatively simple THM behaviour but also complex THM behaviour including chemical processes. Six research teams (BGR, CAS, JAEA, KAERI, SNL and Taipower) participated the Task D. BGR, CAS, JAEA, KAERI and Taipower research teams selected a THM approach, while the SNL research team selected a TH approach. Step 1 involved the simulation of laboratory test results and was important to check the numerical codes developed by the research teams. Step 1 was divided into four sub steps. The simulation results through the Step 1 identified the parameters for simulation of the Step 2. Basic parameters of the materials (buffer material, backfill material, rock mass, concrete, sand) were provided by JAEA. Special parameters which research team needed were identified by back analysis of Step 1. Most notably the mechanical behaviour of swelling and displacement depended on the applied model (elastic model or elastoplastic model). Parameters such as Young’s modulus were found to need smaller values than characterised in the fundamental laboratory test results (Step 1-1, 1-2) for the elastic model. Although laboratory experiments are usually simple, test results contained some error. For example, if the saturation level is 100 % or higher, it should be considered an error. This situation was presented in the Step 1-3. A possible reason is that the buffer material is a mixture of bentonite and silica sand. When a specimen is cut to measure volume or weight, sand grains will affect the measurement data. In Step 2, boundary conditions such as temperature on the surface of the simulated overpack, heater power of the electrical heaters installed in the simulated overpack, injection pressure and inflow rate of the test water, were applied. The outer boundary conditions can be selected using measured data (injection pressure and inflow rate of the test water that is controlled by the injection systems installed in the sand layer around the buffer material and in the boundary between backfill material and concrete support). Since such measured data has some noise, research teams developed their own simplified boundary conditions. Inner boundary conditions can be selected using measured data as heater power and temperature on the surface of the simulated overpack. These data also contain some noise, so research teams developed their own simplified developed boundary conditions. Task D validated various approaches thorough the simulation of the in-situ full scale EBS system including backfill of the gallery: variations in the coupling processes (THM or THC), analysis codes, and boundary conditions. Temperature distribution in the buffer material was simulated well by all research teams. This means thermal behaviour is not sensitive to the simulation approaches. Although the water content distribution on the outside of the buffer material was well simulated by all research teams, the simulation results differ from the measured values inside the buffer material (at the centre and inside, near the simulated overpack). The buffer material is made from tap water, but in the in-situ experiment, saline groundwater infiltrates the buffer material. Therefore, the selection of the hydraulic parameters of the buffer material greatly affects the simulation results of the re saturation behaviour of the buffer material. In the Horonobe EBS experiment, measured values suitable for validating the simulation results were not obtained near the simulated overpack. When simulating the pressure and deformation of the buffer material, the measurement data is easily affected by the installation conditions of the measurement sensors, so verifying the measurement data itself remains an issue. Mechanical simulation results differ depending on whether they are considered as elastic or elastoplastic phenomena. The accuracy of measured in-situ data can be assessed by detailed analysis comparing sampling specimen analysis and measured data. The Horonobe EBS experiment is scheduled to be dismantled in the future (FY2026 and 2027). This detailed dismantling investigation will finally confirm the measured data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1986

Mechanical and swelling behaviour of well characterized polybutadiene networks

Endlinking of hydroxyl-terminated polybutadiene with the appropriate isocyanate has been used to prepare well characterized networks. Two networks have been studied with molecular weights of the prepolymers being 6100 and 2400 g/mole by g.p.c. Cylindrical specimens were prepared and the derivatives of the stored energy function with respect to the stretch invariants were determined by torque and normal force measurements in torsion. From these data the Valanis-Landel (1967) stored energy function derivatives w-prime(lambda) were determined for both networks. The stored energy function for the junction constraint model of Flory (1953, 1977, 1979, 1985) which is a special form of the Valanis-Landel function, has been fitted to that determined from the experiments. The contributions to the stored energy function from the phantom network and from the junction constraints respectively do not agree with predictions from the topologies of the networks. In spite of this, the form of w-prime(lambda) for the junction constraint model gives an excellent 'curve fit' to the data. Comparison is also made with equilibrium swelling.

Mckenna, Gregory B.↗
DOE OSTI2023

Stretching of immersed polyelectrolyte brushes in shear flow

In this article, the way that polymer brushes respond to shear flow has important implications in various applications, including antifouling, corrosion protection, and stimuli-responsive materials. However, there is still much to learn about the behaviours and mechanisms that govern these responses. To address this gap in knowledge, our study uses in situ X-ray reflectivity to investigate how poly(styrene sulfonate) (PSS) brushes stretch and change in different environments, such as isopropanol (a poor solvent), water (a good solvent), and aqueous solutions containing various cations (Cs + , Ba 2+ , La 3+ , and Y 3+ ). We have designed a custom apparatus that exposes the PSS brushes to both tangential shear forces from the primary flow and upward drag forces from a secondary flow. Our experimental findings clearly show that shear forces have a significant impact on how the chains in PSS brushes are arranged. At low shear rates, the tangential shear force causes the chains to tilt, leading to brush contraction. In contrast, higher shear rates generate an upward shear force that stretches and expands the chains. By analysing electron density profiles obtained from X-ray reflectivity, we gain valuable insights into how the PSS brushes respond structurally, especially the role of the diffuse layer in this dynamic behaviour. Our results highlight the importance of the initial chain configuration, which is influenced by the solvent and cations present, in shaping how polymer brushes respond to shear flow. The strength of the salt bridge network also plays a crucial role in determining how easily the brushes can stretch, with stronger networks offering more resistance to stretching. Ultimately, our study aims to enhance our understanding of polymer physics at interfaces, with a particular focus on practical applications involving polymer brushes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

An improved specimen preparation method for marine shallow gas-bearing sand sediments and its validations

Instabilities of shallow gas-charged seabed are potential geological hazards in ocean engineering. In practice, the conventional field sampling techniques failed to obtain undisturbed gas-bearing sediments from the seabed for laboratory mechanical testing because of sensitive gas exsolution and escape from sediments. However, preparation of representative remoulded gas-charged specimens is a challenging issue, because it is rather difficult to quantitatively control the gas content and obtain uniform distribution of gas bubbles within the specimen. Given the above problems, this work proposes a reliable approach to reconstitute the high-saturation specimen of gas-charged sediments in the laboratory by an improved multifunction integrated triaxial apparatus (MITA). This apparatus is developed based on an advanced stress path triaxial system by introducing a temperature-controlled system and a wave-monitoring system. The temperature-controlled system is used to accurately mimic the in situ environments of sediments in the seabed. The wave-monitoring system is utilized to identify exsolution point of free gas and examine the disturbance of gas to specimens during gas exsolution. The detailed procedure of gassy specimen preparation is introduced. Then, the quality of prepared specimens using our improved apparatus is validated by the high-resolution micro-X-ray computed tomography (μCT) scanning test, from which bubble occurrence and size distribution within the gassy sand specimen can be obtained; and preliminary mechanical tests on gassy sand specimens with various initial saturation degrees are performed. The proposed specimen preparation procedure succeeds in proving the postulated occurrence state of gas bubbles in coarse-grained sediments and accurately controlling the gas content.

58 GEOSCIENCES↗
DOE OSTI2025

The effect of blue and infrared laser melting frequency on oxide morphology in 304L

Continuous Wave Laser Beam (LB) melting offers control over the localised heating and cooling of melt pools for welding, brazing, additive manufacturing and solidification. Research into laserliquid metal interactions has primarily focused on the heat and mass transport under large thermal gradients imposed by the localised melting conditions. Recent commercial availability of blue (450 nm) wavelength lasers has enabled the printing of material with poor IR (1064) nm attenuation like Cu. However, little research has been conducted into varying input laser frequency and scan rate at fixed absorption to understand the effects of laser light on surface oxide formation and the underlying liquid metal thermodynamic response. Here, this article conducts laser melting of 304L under Blue (450 nm) and Infrared (IR, 1064 nm) laser frequencies and examines their impact on laser oxide thickness, chemistry and coloration. We find that laser frequencies induce changes in the oxide layer thickness and chemistry that cannot be explained using conventional thermal absorption shifts and fluid dynamics. We suggest that light coupling may have thermodynamic implications for the chemical potential of the liquid metal, which may drive the observed phase behaviour. Identifying mechanisms for the tuning of the chemical potential via laser frequency control could enable the ability to control solidification microstructure and atomic ordering in laser welding and additive manufacturing processes.

304L↗
DOE OSTI2026

Innovative Interfacial Engineering for Simultaneous Enhancement in Efficiency, Stability, and Reliability in Perovskite Devices

The overarching objective of this project was to increase significantly the mechanical adhesion toughness of the key interfaces in PSCs, thereby improving the durability and reliability of PSCs and minimodules, while simultaneously enhancing their PCE. This is achieved by incorporating rationally-chosen self-assembled monolayers (SAMs) at key PSC interfaces. Inherently scalable methods for the deposition of MHP light-absorber thin films and SAMs are employed to ensure a viable path towards manufacturability. Furthermore, detailed understanding of mechanisms of PSCs and minimodules degradation, and SAMs-induced mitigation, is provided. As part of the project accomplishments, >60% increase in the adhesion toughness of the key PSC interfaces over their SAMs-free control counterparts was achieved. Also, PCEs >20% and >19% in rigid and flexible, respectively, single-junction PSCs (~1 cm 2 area) were achieved. It was shown that <20% PCE loss in flexible PSCs with SAMs can be achieved after bend testing. It was demonstrated that T80 (80% retention of initial PCE) of >5,000 hours in rigid PSCs (~1 cm2 area) can be achieved. Comprehensive understanding of the degradation mechanisms in PSCs was obtained. These strategies were adopted towards developing minimodules. PCE of >21% was obtained in an 6-cm 2 area minimodule, with T91 of 1,000 hours.

14 SOLAR ENERGY↗
DOE OSTI2020

Competing ferro- and antiferromagnetic exchange drives shape-selective $\mathrm{Co_3O_4}$ nanomagnetism

We have synthesized three different shapes of Co 3 O 4 nanoparticles to investigate the relationships between the surface Co 2+ and Co 3+ bonding quantified by exploiting the known exposed surface planes, terminations, and coordiations of Co 3 O 4 nanoparticle spheres, cubes and plates. Subsequently this information is related to the unusual behaviour observed in the magnetism. The competition of exchange interactions at the surface provides the mechanism for different behaviours in the shapes. The cubes display weakened antiferromagnetic interactions in the form of a spin-flop that occurs at the surface, while the plates show distinct ferromagnetic behaviour due to the strong competition between the interactions. We elucidate the spin properties which are highly sensitive to bonding and crystal field environments. This work provides a new window into the mechanisms behind surface magnetism.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Formation, structure, and thermal stability evolution of ternesite based on a single-stage sintering process

Highlights: • The synthesis of high-purity ternesite based on a single-stage sintering process was firstly studied. • The formation mechanism and crystallization behaviour of ternesite during sintering were investigated. • The structure perfection and symmetry of ternesite crystals were increased with its growth. • The growth and structural development of ternesite crystals during sintering resulted in a higher thermal stability of itself. Ternesite was prepared via a single-stage solid-state reaction from stoichiometric quantities of the CaCO{sub 3}, SiO{sub 2} and CaSO{sub 4}·2H{sub 2}O precursors. In this paper, the formation, structure, and thermal stability evolution of ternesite during sintering were investigated ex situ after quenching. The optimal sintering temperature for the formation of high-purity ternesite was approximately 1200 °C for 12 h, of which the purity level can reach as high as 96.3%. The results from scanning electron microscopy analysis suggest that the formation of ternesite benefited from the preformation of the intermediate silicate phase. Increasing the sintering temperature from 1100 °C to approximately 1250 °C was favourable for the growth of ternesite crystals, and a prolonged duration can also promote this behaviour. The structural perfection and symmetry of ternesite crystals increased with its growth, which was demonstrated by a multimethod approach. By means of thermal analysis, the growth and structural development of ternesite crystals during sintering eventually resulted in a higher thermal stability.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic insights into metal hardening

For thousands of years, humans have exploited the natural property of metals to get stronger or harden when mechanically deformed. Ultimately rooted in the motion of dislocations, mechanisms of metal hardening have remained in the cross-hairs of physical metallurgists for over a century. Here, we performed atomistic simulations at the limits of supercomputing that are sufficiently large to be statistically representative of macroscopic crystal plasticity yet fully resolved to examine the origins of metal hardening at its most fundamental level of atomic motion. We demonstrate that the notorious staged (inflection) hardening of metals is a direct consequence of crystal rotation under uniaxial straining. At odds with widely divergent and contradictory views in the literature, we observe that basic mechanisms of dislocation behaviour are the same across all stages of metal hardening.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Beam Shaping and Oscillation for Metals Additive Manufacturing

Additive Manufacturing (AM) is pivotal for next-generation industrial manufacturing but is hampered by process control challenges leading to unwanted defects and sub-optimal material properties. Our research builds on prior work that utilized beam oscillation techniques to mitigate these issues (Wu et al., 2023). We focus on investigating the influence of beam oscillation frequency on melt pool dynamics, utilizing in-situ synchrotron material characterization from the ESRF (Chen et al., 2026). Preliminary findings indicated that beam oscillation results in unique fluid flow patterns and enhanced melting stability. These findings suggested the possibility of optimized AM process control, including minimized defects and tailored thermal histories. We proposed further research to explore the effects of beam oscillation frequencies comprehensively, using the in-situ characterization capabilities at the ESRF. The goal was to quantify this relationship, offering a pathway to more precise AM process control and optimization. Our research is expected to offer new scientific insights into the fluid mechanics and thermal behaviour in AM, contributing to its broader applicability and commercial viability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Learned magnetic map cues and two mechanisms of magnetoreception in turtles

Growing evidence indicates that migratory animals exploit the magnetic field of the Earth for navigation, both as a compass to determine direction and as a map to determine geographical position. It has long been proposed that, to navigate using a magnetic map, animals must learn the magnetic coordinates of the destination, yet the pivotal hypothesis that animals can learn magnetic signatures of geographical areas has, to our knowledge, yet to be tested. Here, in this work, we report that an iconic navigating species, the loggerhead turtle ( Caretta caretta ), can learn such information. When fed repeatedly in magnetic fields replicating those that exist in particular oceanic locations, juvenile turtles learned to distinguish magnetic fields in which they encountered food from magnetic fields that exist elsewhere, an ability that might underlie foraging site fidelity. Conditioned responses in this new magnetic map assay were unaffected by radiofrequency oscillating magnetic fields, a treatment expected to disrupt radical-pair-based chemical magnetoreception, suggesting that the magnetic map sense of the turtle does not rely on this mechanism. By contrast, orientation behaviour that required use of the magnetic compass was disrupted by radiofrequency oscillating magnetic fields. The findings provide evidence that two different mechanisms of magnetoreception underlie the magnetic map and magnetic compass in sea turtles.

animal behaviour↗