SEARCH · Engineering Papers
Results for “MINERALOGY”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Quantitative mineralogy for facies definition in the Marcellus Shale (Appalachian Basin, USA) using XRD-XRF integration
Not Available
CO 2 utilization in built environment via the P CO 2 swing carbonation of alkaline solid wastes with different mineralogy
Carbon mineralization to solid carbonates is one of the reaction pathways that can not only utilize captured CO 2 but also potentially store it in the long term. In this study, the dissolution and carbonation behaviors of alkaline solid wastes (i.e., waste concrete) was investigated. Concrete is one of the main contributors to a large carbon emission in the built environment. Thus, the upcycling of waste concrete via CO 2 utilization has multifaceted environmental benefits including CO 2 emission reduction, waste management and reduced mining. Unlike natural silicate minerals such as olivine and serpentine, alkaline solid wastes including waste concrete are highly reactive, and thus, their dissolution and carbonation behaviors vary significantly. Here, both conventional acid (e.g., hydrochloric acid) and less studied carbonic acid (i.e., CO 2 saturated water) solvent systems were explored to extract Ca from concrete. Non-stoichiometric dissolution behaviors between Ca and Si were confirmed under far-from-equilibrium conditions (0.1 wt% slurry density), and the re-precipitation of the extracted Si was observed at near-equilibrium conditions (5 wt% slurry density), when the Ca extraction was performed at a controlled pH of 3. These experiments, with a wide range of slurry densities, provided valuable insight into Si re-precipitation phenomena and its effect on the mass transfer limitation during concrete dissolution. Next, the use of the partial pressure of CO 2 for the pH swing carbon mineralization process was investigated for concrete, and the results were compared to those of Mg-bearing silicate minerals. In the P CO 2 swing process, the extraction of Ca was significantly limited by the precipitation of the carbonate phase (i.e., calcite), since CO 2 bubbling could not provide a low enough pH condition for concrete–water–CO 2 systems. Furthermore, this study showed that the two-step carbon mineralization via P CO 2 swing, that has been developed for Mg-bearing silicate minerals, may not be viable for highly reactive Ca-bearing silicate materials (e.g., concrete). The precipitated calcium carbonate (PCC) derived from waste concrete via a pH swing process showed very promising results with a high CO 2 utilization potential as an upcycled construction material.
Relationship between mineralogy and porosity in seals relevant to geologic CO2 sequestration
Explore the source record for details and available documents.
Impact of Multiscale Mineralogical and Sedimentary Heterogeneity on Mechanical Behavior of Mancos Shale.
Abstract not provided.
Actinides in the nuclear fuel cycle: Role of mineralogy and geochemistry. Hallimond Lecture of the Mineralogical Society of Great Britain and Ireland
Explore the source record for details and available documents.
Multiscale characteristics of mechanical and mineralogical heterogeneity using nanoindentation and Maps Mineralogy in Mancos Shale.
Abstract not provided.
Modeling Impacts of Dust Mineralogy on Fast Climate Response
Mineralogical composition drives dust impacts on Earth's climate systems. However, most climate models still use homogeneous dust, without accounting for the temporal and spatial variation in mineralogy. To quantify the radiative impact of resolving dust mineralogy on Earth's climate, we implement and simulate the distribution of dust minerals (i.e., illite, kaolinite, smectite, hematite, calcite, feldspar, quartz, and gypsum) from Claquin et al. (1999) (C1999) and activate their interaction with radiation in the GFDL AM4.0 model. Resolving mineralogy reduces dust absorption compared to the homogeneous dust used in the standard GFDL AM4.0 model that assumes a globally uniform hematite volume content of 2.7 % (HD27). The reduction in dust absorption results in improved agreement with observation-based single-scattering albedo (SSA), radiative fluxes from CERES (the Clouds and the Earth's Radiant Energy System), and land surface temperature from the CRU (Climatic Research Unit) compared to the baseline HD27 model version. It also results in distinct radiative impacts on Earth's climate over North Africa. Over the 19-year (from 2001 to 2019) modeled period during JJA (June–July–August), the reduction in dust absorption in AM4.0 leads to a reduction of over 50 % in net downward radiation across the Sahara and approximately 20 % over the Sahel at the top of the atmosphere (TOA) compared to the baseline HD27 model version. The reduced dust absorption weakens the atmospheric warming effect of dust aerosols and leads to an alteration in land surface temperature, resulting in a decrease of 0.66 K over the Sahara and an increase of 0.7 K over the Sahel. The less warming in the atmosphere suppresses ascent and weakens the monsoon inflow from the Gulf of Guinea. This brings less moisture to the Sahel, which combined with decreased ascent induces a reduction of precipitation. To isolate the effect of reduced absorption compared to resolving spatial and temporal mineralogy, we carry out a simulation where the hematite volume content of homogeneous dust is reduced from 2.7 % to 0.9 % (HD09). The dust absorption (e.g., single-scattering albedo) of HD09 is comparable to that of the mineralogically speciated model on a global mean scale, albeit with a lower spatial variation that arises solely from particle size. Comparison of the two models indicates that the spatial inhomogeneity in dust absorption resulting from resolving mineralogy does not have significant impacts on Earth's radiation and climate, provided there is a similar level of dust absorption on a global mean scale before and after resolving dust mineralogy. However, uncertainties related to emission and distribution of minerals may blur the advantages of resolving minerals to study their impact on radiation, cloud properties, ocean biogeochemistry, air quality, and photochemistry. On the other hand, lumping together clay minerals (i.e., illite, kaolinite, and smectite), but excluding externally mixed hematite and gypsum, appears to provide both computational efficiency and relative accuracy. Nevertheless, for specific research, it may be necessary to fully resolve mineralogy to achieve accuracy.
Strategies and Technologies for In Situ Mineralogical Investigations on Mars
Surface landers on Mars (Viking and Pathfinder) have not revealed satisfying answers to the mineralogy and lithology of the planet's surface. In part, this results from their prime directives: Viking focused on exobiology, Pathfinder focused on technology demonstration. The analytical instruments on board the landers made admirable attempts to extract the mineralogy and geology of Mars, as did countless modeling efforts after the missions. Here we suggest a framework for elucidating martian, or any other planetary geology, through an approach that defines (a) type of information required, (b) explorational strategy harmonious with acquisition of these data, (c) interpretation approach to the data, (d) compatible mission architecture, (e) instrumentation for interrogating rocks and soil. (a) Data required: The composition of a planet is ordered at scales ranging from molecules to minerals to rocks, and from geological units to provinces to planetary-scale systems. The largest ordering that in situ compositional instruments can attempt to interrogate is rock type "aggregate" information. This is what the geologist attempts to identify first. From this, mineralogy can be either directly seen or inferred. From mineralogy can be determined elemental abundances and perhaps the state of the compounds as being crystalline or amorphous. Knowledge of rock type and mineralogy is critical for elucidating geologic process. Mars landers acquired extremely valuable elemental data, but attempted to move from elements to aggregates, but this can only be done by making many assumptions and sometimes giant leaps of faith. Data we believe essential are elements, minerals, degree of ordering of compounds, and the aggregate or rock type that these materials compose. (b) Explorational strategy: A lander should function as a surrogate geologist. Of the total landscape, a geologist sees much, but gives detailed attention to an infinitesimally small amount of what is seen. To acquire samples worth detailed scrutiny, as many samples as possible need examining at a cursory or reconnaissance level. A representative, statistically-meaningful sample number cannot be overemphasized. This maxim still applies to geological exploration of our own planet of which we have abundant knowledge. Analysis of many samples mandates low-power consumption per sample. (c) Data interpretation: No single instrument can analyze the full spectrum of the x-axis. An instrument is optimized for detecting certain material characteristics and must therefore affix itself to some point on the x-axis. Any conclusions drawn about data to the left or right of the instrument's position on this axis must necessarily be derived by inference. Hence, it seems logical to include on a mission, instruments that are not closely spaced in their x-axis-position, and if only two analytical methods are used, as shown, they should start at opposite ends of the axis and work towards the center. As examples, we depict a high-resolution camera to evaluate rock type ("aggregate" state) and mineralogy, and an x-ray diffractometer-fluorescence spectrometer (XRD-XRF) to determine elements, minerals, and the degree of order of materials. (d) Mission architecture: No instrument or suite of instruments can be relied upon to always give truly unequivocal analyses. The suite of instruments should therefore permit conclusions of one instrument to be checked against those of another through closed analytical loops. These "loops" can be structured by a combination of orbital imagery, descent imagery, broad-band site viewing/analysis, and data that cover both x and y axes. For example, the detection of a basaltic-looking rock with a microscope should be checked against the elements detected, the appearance of the rock as a lava flow from descent imagery, and so forth. (e) Instrumentation: To satisfy the above criteria, it is necessary to: (i) See the rock or soil with high resolution + magnification, (ii) Examine many samples, (iii) Consume little power per analysis, (iv) Determine elemental species, (v) Determine mineralogy directly (not inferentially) and the degree of ordering of compounds, (vi) Start analyzing from both ends of the x-axis. Every geologist wants to see the hand sample first, and apply a hand lens to its surface. This has not been the starting point for missions to Mars. Thus, our technology satisfies all these criteria . This XRD-XRF-Optical instrument currently being developed, analyses rock or soil surfaces without the need for sample acquisition or preparation; this satisfies the power criterion, and enables many analyses. The device acquires direct mineralogy and determines elemental species. The embedded endoscopic camera satisfies the critical criterion of close inspection of samples; the fiber optic cable can also be used for IR, LTV, or laser sample analysis. Additional information is contained in the original (Figures).
Deciphering mineralogical changes and carbonation development during hydration and ageing of a consolidated ternary blended cement paste
To understand the main properties of cement, a ubiquitous material, a sound description of its chemistry and mineralogy, including its reactivity in aggressive environments and its mechanical properties, is vital. In particular, the porosity distribution and associated sample carbonation, both of which affect cement's properties and durability, should be quantified accurately, and their kinetics and mechanisms of formation known both in detail and in situ . However, traditional methods of cement mineralogy analysis ( e.g. chemical mapping) involve sample preparation ( e.g. slicing) that can be destructive and/or expose cement to the atmosphere, leading to preparation artefacts ( e.g. dehydration). In addition, the kinetics of mineralogical development during hydration, and associated porosity development, cannot be examined. To circumvent these issues, X-ray diffraction computed tomography (XRD-CT) has been used. This allowed the mineralogy of ternary blended cement composed of clinker, fly ash and blast furnace slag to be deciphered. Consistent with previous results obtained for both powdered samples and dilute systems, it was possible, using a consolidated cement paste (with a water-to-solid ratio akin to that used in civil engineering), to determine that the mineralogy consists of alite (only detected in the in situ hydration experiment), calcite, calcium silicate hydrates (C-S-H), ettringite, mullite, portlandite, and an amorphous fraction of unreacted slag and fly ash. Mineralogical evolution during the first hydration steps indicated fast ferrite reactivity. Insights were also gained into how the cement porosity evolves over time and into associated spatially and time-resolved carbonation mechanisms. It was observed that macroporosity developed in less than 30 h of hydration, with pore sizes reaching about 100–150 µm in width. Carbonation was not observed for this time scale, but was found to affect the first 100 µm of cement located around macropores in a sample cured for six months. Regarding this carbonation, the only mineral detected was calcite.
Mineralogy of Rock Flour in Glaciated Volcanic Terrains: An Analog for a Cold and Icy Early Mars
Geomorphological and mineralogical data from early Martian surfaces indicate liquid water was present on ancient Mars. The relative surface temperatures, however, remain a subject of debate. Was early Mars warm and wet or cold and icy with punctuated periods of warmth and ice melt? By characterizing the mineralogy and geochemistry of modern icy mafic terrains on Earth, we can search for these characteristics in early Martian terrains to better constrain the early Martian climate. Here, we describe the mineralogy of glacial flour in a modern glaciated volcanic terrain in Oregon, USA. We are particularly interested in secondary phases that form in these environments, and we hypothesize that poorly crystalline phases may preferentially form in these terrains because of the low temperatures and the seasonality of melt water production. A description of the mineralogy of the moraines, the composition of the amorphous materials, and the geochemistry of the glacial melt waters are presented elsewhere. Glacial flour is made up of silt- and clay-sized particles that form from the physical weathering of rock underlying a wet-based glacier as the glacier slides over it. Flour is usually transported from underneath a glacier by melt water streams. The geochemistry of glacial melt water streams has been studied extensively and has been used to infer weathering reactions within glacial systems. However, the mineralogy of these environments, especially on mafic volcanic terrains, is not well studied. Rock flour is a ubiquitous physical weathering product in glaciated terrains and, therefore, affects microbial habitats, stream and lake chemistry, and chemical weathering processes. and by studying the mineralogy of glacial flour, we can better understand geochemical and microbiological processes in subglacial and proglacial terrains.
Using Mineralogy of the Bagnold Dune Field in Gale Crater to Interpret Eolian Sediment Sorting on the Martian Surface
The Mars Science Laboratory Curiosity rover landed in Gale crater in August 2012 to characterize modern and ancient surface environments. Curiosity executed a two-phase campaign to study the morphology, activity, physical properties, and chemical and mineralogical composition of the Bagnold Dune Field, an active eolian dune field on the lower slopes of Aeolis Mons (Mount Sharp). Detectable aspects of dune sand mineralogy have been examined from orbit with the visible/short-wave infrared spectrometer CRISMand the thermal-infrared spectrometers THEMIS and TES. CRISM data demonstrate variations in plagioclase, pyroxene, and olivine abundances across the dune field. Curiosity analyzed sediments from two locations in the dune field to evaluate the causes of the mineralogical differences observed from orbit. The Gobabeb sample was collected from Namib Dune, a barchanoidal dune on the upwind margin of the dune field, and the Ogunquit Beach sample was collected from the Mount Desert Island sand patch located downwind from Namib. These samples were sieved to <150 μm and delivered to the CheMin X-ray diffraction instrument for quantitative mineralogical analysis. CRISM-derived mineralogy of the Namib Dune and Mount Desert Island and CheMin-derived mineralogy of the Gobabeb and Ogunquit Beach samples can be used in a value-added manner to interpret grain segregation at the bedform to dune-field scale and evaluate contributions from local sediment sources. Models of CRISM data demonstrate that Mount Desert Island is more enriched in olivine and less enriched in plagioclase than Namib dune, suggesting that fine-grained mafic sediments are preferentially mobilized downwind. Curiosity data indicate olivine also forms a coarse lag on the lee sides of barchanoidal dunes. Minor abundances of hematite, quartz, and anhydrite and small differences in the crystal chemistry of plagioclase and pyroxene derived from CheMin data suggest that sediments from the underlying lacustrine rocks also contribute to the Bagnold sands.
Mantle Source Mineralogy Inferred from Incompatible Element Ratios in Shergottites
The mineralogy of the martian mantle is a poorly known but vital compositional parameter. In the absence of samples of martian mantle peridotites, the mineralogy has been inferred from bulk composition constrained by a mix of cosmochemical and martian meteoritic constraints. Such a mineralogy reflects the primordial mantle composition, but mantle source regions that differentiated from a magma ocean are not likely to have the same mineralogy as bulk silicate Mars. An alternative approach is to infer source mineralogy of the martian mantle from the analysis of incompatible elements in shergottites. In a recent study, we showed that the general compatibility order of trace lithophile elements in martian mantle is similar to that of MORB mantle, with some exceptions. Compared to MORB mantle, in martian mantle: (1) highly incompatible elements (Th, Nb, Ta and U) are less incompatible relative to La; (2) K is significantly more compatible with respect to other elements; and (3) the HREEs are more compatible. In this study, we calculated effective partition coefficients of trace elements directly from martian igneous meteorites and used this data to infer the source mineralogy of the martian mantle.
Recent Mineralogical Discoveries in Gale Crater, Mars from the CheMin XRD Instrument, Demonstrating a Watery Past
Curiosity landed in Gale crater August 2012 and has traversed (~27 km) sedimentary rocks that comprise a ~5 km-high mound, informally known as Mount Sharp, to investigate depositional/diagenetic environments and potential habitability. VSWIR spectra revealed the lowermost slopes of Mount Sharp contain mineral assemblages that are indicative of water-rock interactions (1-3), with sulfate-bearing units overlying phyllosilicate-bearing units. This mineralogical succession may mark the beginning of the transition from a relatively wet/warm to a very dry/cold Mars (e.g., 1, 4). Thirty-four powdered rock samples have been analyzed by the CheMin XRD instrument and mineralogical results from the first 6 years of the mission are reviewed in [5]. Here we describe the mineralogical diversity observed over the most recent 4 years. Sediments in the Vera Rubin Ridge (VRR) and Glen Torridon (GT) region were deposited in a lacustrine-fluvial environment and are syndepositional. The mineralogy suggests post-depositional fluid-rock interaction. Differences in mineralogy could have been the result of silica-poor, briny groundwater that destabilized smectite and precipitated hematite in VRR [6]. Other hypotheses include lake water-groundwater mixing or diagenesis driven by deeply sourced fluids altering smectite to precipitate hematite and amorphous silica. Preserved bedforms in the clay-sulfate transition region indicate a change from lacustrine-fluvial to aeolian depositional environments. Mineralogical changes include the identification of goethite along with the disappearance of phyllosilicate. The absence of crystalline Mg-sulfate in drilled samples from this transition region may mean that: 1) Sulfates are concentrated in secondary concretions not sampled by Curiosity’s drill, or 2) Sulfate components are either X-ray amorphous or if crystalline, became amorphous in the relatively low-humidity environment of the rover. Continued exploration of sulfate-rich rocks will elucidate this environmental transition above the phyllosilicate-rich sediments.
Using Mineralogy to Interpret Martian Geologic History
The surface mineralogy of Mars is key to interpreting the planet’s geologic history and constraining when and where Mars may have been habitable to microbial life. Orbital mineralogical data from infrared spectrometers collected over the last two decades have demonstrated that Mars is more than a basaltic planet. Thermal infrared (TIR) emission spectrometers have identified regional variations in igneous minerals, iron oxides, and chloride salts, showing evidence for magmatic evolution and aqueous alteration. Orbital visible/shortwave infrared reflectance spectra provide detailed information about the aqueous history of Mars through the identification of clay minerals, sulfates, carbonates, zeolites, and amorphous materials in ancient ~3-4-billion-year-old terrains. Mineralogical data from rovers allow us to better characterize mineral formation mechanisms by identifying mineral assemblages and placing them in geologic context using outcrop- to grain-scale images. TIR and Mössbauer data from the Mars Exploration Rovers helped identify an ancient dune-interdune playa environment with multiple episodes of groundwater at Meridiani Planum and volcanism-induced hydrothermalism at Gusev crater. The CheMin X-ray diffractometer on the Mars Science Laboratory Curiosity rover in Gale crater is the first fully quantitative mineralogical instrument sent to another planetary surface. CheMin data allow the quantification of minerals and X-ray amorphous materials with a mineral detection limit of <1 wt.% and provide crystal chemistry of major phases from refined unit-cell parameters. CheMin has revealed local mineralogical changes in ancient sedimentary rocks not seen from orbit and helped identify habitable environments. Throughout the 600+ m of vertical stratigraphy studied so far, changes in clay mineralogy, Fe-oxides/oxyhydroxides, sulfates, and carbonates demonstrate a long history of surface and groundwater at Gale crater with variable salinity, pH, Eh, and temperature. Recent CheMin data document a decrease in clay minerals and an increase in sulfate minerals in younger strata that corresponds with a change from fluvio-lacustrine to eolian depositional environments, potentially documenting a change to a drier climate across the planet.
Trade-Offs of Simplified Versus Comprehensive Representation of Mineralogy When Studying Dust Impacts on Earth’s Climate Systems
The intensity and direction of dust impacts on Earth’s climate systems depend on mineral composition. For example, the presence or absence of a few percent of iron oxides in dust will determine if dust is warming or cooling the atmosphere. Similarly, feldspar will enhance ice cloud formation, while acid gases in the atmosphere will react on the surface of dust calcite limiting acid rain. Still, most climate models use a simplified representation of dust mineralogy. They assume a fixed composition at emission which stays invariant during transport and removal. Such simplification assumes spatially and temporally constant physical and chemical properties of dust, and appears to provide satisfactory results when comparing some properties with observations. The trade-off is their lack of spatial gradients, which will fail to induce circulation, cloud and precipitation changes. The two reasons to omit mineral variations are the uncertainty of current atlases of soil mineral composition in arid regions, and, more practically, an improved runtime efficiency. The former reason is losing ground with the recent launch (July 2022) of a dedicated mission (NASA/JPL EMIT) to retrieve global soil mineralogy of dust sources at high spatial resolution. While the EMIT science team is finalizing a satisfactory global map of mineral composition of dust sources, we analyzed the interaction of dust mineralogy on radiation and its impact on the fast temperature response using different representations of mineral composition from detailed and spatially varying to simplified and globally uniform, assuming different hematite contents and methods to calculate optical properties. Our results show that resolving dust mineralogy reduces dust absorption, and results in improved agreement with observation-based single scattering albedo (SSA), radiative fluxes from CERES (the Clouds and the Earth’s Radiant Energy System), and land surface temperature from CRU (Climatic Research Unit), compared to the baseline bulk dust model version. It also results in distinct radiative impacts on Earth’s climate over North Africa. From our 19-year simulation, we will show that it leads to a reduction of over 50% in net downward radiation at top of atmosphere (TOA) across the Sahara and an approximately 20% reduction over the Sahel. We will explain how the surface temperature response affects the monsoon flow from the Gulf of Guinea. Interestingly, we find similar results by simply fixing the hematite content of dust to a globally uniform value of 0.9% by volume. We will discuss the underlying reasons for such results and show that they may be unrelated to the distribution of soil mineralogy. Still, an accurate representation of soil mineralogy is necessary to better understand dust impacts on the Earth’s climate systems.