Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MHZ RANGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Analysis of airborne RF measurements from U.S.A. urban areas

The paper presents in-situ, airborne survey radio-frequency measurements, which were made over the 400-1000 MHz range in May 1977 during the ASSESS-II Space Shuttle/Spacelab simulation aircraft flights. Measurements were made from altitudes of 10,000 to 33,000 feet with a downward-directed 70 deg wide, half-power beamwidth receiving antenna pattern. Channel occupancy percentages are given within a 50 MHz spectrum width, and continuous spectrum-scan measurements are presented for selected locations on the USA West Coast, showing the channel occupancy environment within the 806-890 MHz mobile-service band.

Taylor, R. E.↗
NASA NTRS2006

Digital Front End for Wide-Band VLBI Science Receiver

An upgrade to the very-long-baseline-interferometry (VLBI) science receiver (VSR) a radio receiver used in NASA's Deep Space Network (DSN) is currently being implemented. The current VSR samples standard DSN intermediate- frequency (IF) signals at 256 MHz and after digital down-conversion records data from up to four 16-MHz baseband channels. Currently, IF signals are limited to the 265-to-375-MHz range, and recording rates are limited to less than 80 Mbps. The new digital front end, denoted the Wideband VSR, provides improvements to enable the receiver to process wider bandwidth signals and accommodate more data channels for recording. The Wideband VSR utilizes state-of-the-art commercial analog-to-digital converter and field-programmable gate array (FPGA) integrated circuits, and fiber-optic connections in a custom architecture. It accepts IF signals from 100 to 600 MHz, sampling the signal at 1.28 GHz. The sample data are sent to a digital processing module, using a fiber-optic link for isolation. The digital processing module includes boards designed around an Advanced Telecom Computing Architecture (ATCA) industry-standard backplane. Digital signal processing implemented in FPGAs down-convert the data signals in up to 16 baseband channels with programmable bandwidths from 1 kHz to 16 MHz. Baseband samples are transmitted to a computer via multiple Ethernet connections allowing recording to disk at rates of up to 1 Gbps.

Jongeling, Andre↗
NASA NTRS2013

Submillimeter Planetary Atmospheric Chemistry Exploration Sounder

Planetary Atmospheric Chemistry Exploration Sounder (SPACES), a high-sensitivity laboratory breadboard for a spectrometer targeted at orbital planetary atmospheric analysis. The frequency range is 520 to 590 GHz, with a target noise temperature sensitivity of 2,500 K for detecting water, sulfur compounds, carbon compounds, and other atmospheric constituents. SPACES is a prototype for a powerful tool for the exploration of the chemistry and dynamics of any planetary atmosphere. It is fundamentally a single-pixel receiver for spectral signals emitted by the relevant constituents, intended to be fed by a fixed or movable telescope/antenna. Its front-end sensor translates the received signal down to the 100-MHz range where it can be digitized and the data transferred to a spectrum analyzer for processing, spectrum generation, and accumulation. The individual microwave and submillimeter wave components (mixers, LO high-powered amplifiers, and multipliers) of SPACES were developed in cooperation with other programs, although with this type of instrument in mind. Compared to previous planetary and Earth science instruments, its broad bandwidth (approx. =.13%) and rapid tunability (approx. =.10 ms) are new developments only made possible recently by the advancement in submillimeter circuit design and processing at JPL.

Schlecht, Erich T.↗
NASA NTRS2005

Recent progress in opto-electronic oscillator

The optoelectronic oscillator (OEO) is a unique device based on photonics techniques to generate highly spectrally pure microwave signals [1]. The development of the OEO was motivated by the need for high performance oscillators in the frequency range larger than 10 GHz, where conventional electronic oscillators have a number of limitations. These limitations typically stem from the product of fQ, where f is the oscillator frequency and Q is the quality factor of the resonator in the oscillator. In conventional resonators, whether electromagnetic or piezoelectric, this product is usually a constant. Thus, as the oscillator frequency is pushed higher, the quality factor degrades, resulting in degradation of the phase noise of the oscillator. An approach to mitigate the problem is to start with a very high quality signal in the 5 to 100 MHz range generated by a quartz oscillator and multiply the frequency to achieve the desired microwave signal. Here again, frequency multiplication also results in an increase of the phase noise by a factor of 2010gN, where N is the multiplication factor.

opto-electronic oscillators↗
NASA NTRS2002

Solar Flares, Type III Radio Bursts, Coronal Mass Ejections, and Energetic Particles

In this correlative study between greater than 20 MeV solar proton events, coronal mass ejections (CMEs), flares, and radio bursts it is found that essentially all of the proton events are preceded by groups of type III bursts and all are preceded by CMEs. These type III bursts (that are a flare phenomenon) usually are long-lasting, intense bursts seen in the low-frequency observations made from space. They are caused by streams of electrons traveling from close to the solar surface out to 1 AU. In most events the type III emissions extend into, or originate at, the time when type II and type IV bursts are reported (some 5 to 10 minutes after the start of the associated soft X-ray flare) and have starting frequencies in the 500 to approximately 100 MHz range that often get lower as a function of time. These later type III emissions are often not reported by ground-based observers, probably because of undue attention to type II bursts. It is suggested to call them type III-1. Type III-1 bursts have previously been called shock accelerated (SA) events, but an examination of radio dynamic spectra over an extended frequency range shows that the type III-1 bursts usually start at frequencies above any type II burst that may be present. The bursts sometimes continue beyond the time when type II emission is seen and, furthermore, sometimes occur in the absence of any type II emission. Thus the causative electrons are unlikely to be shock accelerated and probably originate in the reconnection regions below fast CMEs. A search did not find any type III-1 bursts that were not associated with CMEs. The existence of low-frequency type III bursts proves that open field lines extend from within 0.5 radius of the Sun into the interplanetary medium (the bursts start above 100 MHz, and such emission originates within 0.5 solar radius of the solar surface). Thus it is not valid to assume that only closed field lines exist in the flaring regions associated with CMEs and some interplanetary particles originating in such flare regions might be expected in all solar particle events.

Cane, Hilary V.↗
NASA NTRS2011

Operational Parameters, Considerations, and Design Decisions for Resource-Constrained Ion Trap Mass Spectrometers

Mass spectrometers are increasingly finding applications in new and unique areas, often in situations where key operational resources (i.e. power, weight and size) are limited. One such example is the Mars Organic Molecule Analyzer (MOMA). This instrument is a joint venture between NASA and the European Space Agency (ESA) to develop an ion trap mass spectrometer for chemical analysis on Mars. The constraints on such an instrument are significant as are the performance requirements. While the ideal operating parameters for an ion trap are generally well characterized, methods to maintain analytical performance with limited power and system weight need to be investigated and tested. Methods Experiments have been performed on two custom ion trap mass spectrometers developed as prototypes for the MOMA instrument. This hardware consists of quadrupole ion trap electrodes that are 70% the size of common commercial instrumentation. The trapping RF voltage is created with a custom tank circuit that can be tuned over a range of RF frequencies and is driven using laboratory supplies and amplifiers. The entire instrument is controlled with custom Lab VIEW software that allows a high degree of flexibility in the definition of the scan function defining the ion trap experiment. Ions are typically generated via an internal electron ionization source, however, a laser desorption source is also in development for analysis of larger intact molecules. Preliminary Data The main goals in this work have been to reduce the power required to generate the radio frequency trapping field used in an ion trap mass spectrometer. Generally minimizing the power will also reduce the volume and mass of the electronics to support the instrument. In order to achieve optimum performance, commercial instruments typically utilize RF frequencies in the 1 MHz range. Without much concern for power usage, they simply generate the voltage required to access the mass range of interest. In order to reduce the required RF voltage (and power), operation of the ion trap at lower RF frequencies has been investigated. Surprisingly, the performance of the instrument has only been slightly degraded at RF frequencies all the way down to 500 kHz. Mass resolution is relatively stable to this point and depending on the resonant ejection point used, the peak intensity is also quite stable. To date only masses up to m/z 200 have been fully investigated, however, additional studies are planned to verify the performance with higher mass ions. The lower frequency and voltage should reduce the pseudo potential well depth, eventually affecting the trapping efficiency of the instrument -- effect that could manifest itself in significantly limiting the mass range of trapped ions. Other methods to reduce the RF power while maintaining analytical performance are also under investigation. This includes ion ejection at lower q(sub z) values to access a given mass with a lower RF voltage. The loss of mass resolution at lower q(sub eject) points has been measured and current work is underway to leverage scan speed and the use of non-linear resonances in order to counter this trend. The overall trap performance under this range of operating conditions will be presented with a goal of identifying what trade-offs are acceptable.

Danell, Ryan M.↗
NASA NTRS1972

Evidence for a common origin of the electrons responsible for the impulsive X-ray and type III radio bursts.

Observations of impulsive solar flare X-rays greater than or about equal to 10 keV made with the OGO-5 satellite are compared with ground-based measurements of type III solar radio bursts in 10- to 580-MHz range. It is shown that the times of maxima of these two emissions, when detectable, agree within about 18 sec. This maximum time difference is comparable to that between the maxima of the impulsive X-ray and impulsive microwave bursts. In view of the various observational uncertainties, it is argued that the observations are consistent with the impulsive X-ray, impulsive microwave, and type III radio bursts being essentially simultaneous. The observations are also consistent with 10- to 100-keV electron streams being reponsible for the type III emission. The observations indicate that the non-thermal electron groups responsible for the impulsive X-ray, impulsive microwave, and type III radio bursts are accelerated simultaneously in essentially the same region of the solar atmosphere.

Kane, S. R.↗
NASA NTRS1974

A new high-speed solar radio spectrograph for meter and decameter wavelengths

The design and characteristics of a high resolution, digital solar spectrograph are discussed. The spectrometer operates in the 10 to 80 MHz range. The primary considerations in the design of the spectrograph were: (1) optimun sensitivity, (2) wide dynamic range, (3) flexibility in time and frequency resolution, and (4) modern data handling techniques with a simple computer interface.

Mosier, S. R.↗
NASA NTRS1977

CO2 laser communication systems for near-earth space applications

Projections of the growth of earth-sensing systems for the latter half of the 1980's show a data-transmission requirement of 300 Mbit/s and above. The most efficient technique to return the data from a sensing satellite to a ground station is through a geosynchronous data relay satellite. A laser system is most attractive for the space-to-space link. A five-year program was conducted which has shown the basic technical feasibility of accomplishing this link with a CO2 laser system operating at a wavelength near 10 microns. The system uses a mercury-cadmium-telluride infrared mixer cooled to approximately 100 K by a radiative cooler. The laser local oscillator and coupling-modulated laser transmitter use conductively cooled beryllium oxide construction. The optical antenna for transmission and reception has a gain of nominally 92 dB with a 3-dB beamwidth of 80 microrad. Tracking jitter is less than ten microrad, and signal acquisition occurs in less than 1 min. The receiver subsystem has a sensitivity of 10 to the -19th power W/Hz, accommodates a 300-Mbit/s data rate, and can track Doppler frequency variations over a + or - 700-MHz range.

Mcelroy, J. H.↗
NASA NTRS1979

Simultaneous multifrequency observations of Jovian S bursts

The millisecond component of the Jovian decameter emission was studied at high resolution in order to examine the short-term behavior of the S-burst drift rates and to define the drift rate spectrum at high frequencies. By using dynamic spectra of 300 microsec and 3.3 kHz resolution and covering discrete frequency bands in the 26-33 MHz range, large systematic changes in the magnitude of the S-burst drift rates are observed on a time scale of seconds to minutes. The drift rate variability, its dependence on frequency, and absence of the predicted drift rate turnover in the spectrum are interpreted in terms of an ionospheric electron source. Low-resolution intensity-time tracings, abrupt changes in mean drift rates from group to group, and systematic variations in the group-to-group mean drift rates due to predictable temporal changes in the magnetic field gradient on the Io flux tube are discussed. These temporal changes are due to motion of the Io-associated magnetic flux tube in the Jovian magnetosphere.

Flagg, R. S.↗
NASA NTRS1980

The WISP/HF system for Spacelab

The high frequency part of the waves in space plasmas system, WISP/HF, is a flexible shuttle Spacelab instrument for transmitting, receiving, and processing signals in the 0.3 to 30 MHz range. It permits a wide range of plasma wave experiments in the ionosphere including studies of the transmitting antenna, fundamentals of electromagnetic (EM) and electrostatic (ES) waves in magnetoplasmas, instabilities and nonlinearities, and remote sounding of ionospheric structure. Collaborative investigations involving other WISP equipment (e.g., antenna and propagation studies with the WISP/VLF system) or other Spacelab facilities (e.g., beam plasma interactions using charged particle guns) are envisaged. A few specific examples illustrate the relevance of WISP/HF to current scientific interest. The overall goal is to help build a comprehensive understanding of plasmaspheric wave physics through group studies.

James, H. G.↗
NASA NTRS1980

Ultrasonic imaging using trapped energy mode Fresnel lens transducers

Trapped-energy focusing transducers operating in the 2-5 MHz range have been fabricated by plating concentric rings of electrodes on a piezoelectric plate. The concentric ring structure acts as a Fresnel lens and can be used to obtain excellent lateral focusing of ultrasonic waves. The trapping is sufficiently strong to permit optimization of electrode spacings to suppress spurious virtual foci and ring sidelobes.

Das, P.↗
NASA NTRS1981

Lightning amplitude spectra in the interval from 100 kHz to 20 MHz

The electric radiation fields produced by lightning return strokes, stepped leaders, and intracloud discharge processes have been Fourier-analyzed to determine amplitude spectra for these processes from about 100 kHz to 20 MHz. The fields were recorded under conditions where the lightning locations were known and where the field propagation from the lightning sources to the recording site was entirely over salt water. The spectra for return strokes show an f exp -1 frequency dependence from 100 kHz to 2 MHz, an f exp -2 dependence between 2 and 10 MHz, and an f exp -5 decrease above 10 MHz. In the 1 to 20 MHz range, the spectra of the initial fast transition in return strokes, the initial fast-rising portion of leader steps and the fast transitions in positive intracloud pulses are surprisingly similar.

Weidman, C. D.↗
NASA NTRS1982

Control structures for high speed processors

A special processor was designed to function as a Reed Solomon decoder with throughput data rate in the Mhz range. This data rate is significantly greater than is possible with conventional digital architectures. To achieve this rate, the processor design includes sequential, pipelined, distributed, and parallel processing. The processor was designed using a high level language register transfer language. The RTL can be used to describe how the different processes are implemented by the hardware. One problem of special interest was the development of dependent processes which are analogous to software subroutines. For greater flexibility, the RTL control structure was implemented in ROM. The special purpose hardware required approximately 1000 SSI and MSI components. The data rate throughput is 2.5 megabits/second. This data rate is achieved through the use of pipelined and distributed processing. This data rate can be compared with 800 kilobits/second in a recently proposed very large scale integration design of a Reed Solomon encoder.

Maki, G. K.↗
NASA NTRS1981

Radio observations of Abell clusters and a comparison with certain Einstein observations

Areas around 70 clusters have been observed at the Arecibo Observatory primarily for coordination with about 60 Einstein X-ray sources. Arecibo source coordinates and flux density are tabulated, and some identifications are made with cataloged radio sources. Statistical estimates are made of the percentage of cluster sources among all sources in certain areas and to limits on the flux density of 430 MHz. Arecibo and other radio data are compared with the available Einstein data of seven clusters. Not every Einstein source has a radio counterpart, and the counterparts may variously be bilobed, tailed, or single. A parameter which is proportional to source continuum power at 430 MHz ranges over fewer orders of magnitude than the associated source X-ray luminosity, with no certain correlation between these parameters. NRAO Green Bank interferometer observations of A401 and A2142 are reported.

Johnson, H. M.↗
NASA NTRS1982

Optogalvanic stabilization and offset tuning of a carbon dioxide waveguide laser

A feedback loop employing the change in discharge impedance with output power is used to stabilize the frequency of a CO2 waveguide laser. The relatively high operating pressure of the laser combined with a zero offset feature in the feedback loop allows continuous tuning of the stabilized frequency over a 300-400 MHz range.

Kavaya, M. J.↗
NASA NTRS1980

Analysis of aging data on SAW oscillators

Test oscillators including delay lines and resonators in the 300-400 MHz range have been investigated with reference to the long-term stability (aging) characteristics. All devices were fabricated on rotated Y-cut quartz plates (40 deg), and either gold or platinum metallization was used; all packages were high-quality hermetic enclosures, and the mounting was strictly mechanical, with no organics or silicone rubbers used. It is shown that drift of less than 2 ppm in the first year can be obtained on a significant fraction of the devices when reasonably clean packages are used. The data also suggest that the transducer metallization (at least for aluminum) is very likely the source of the relaxation mechanism that causes the frequency drift.

Parker, T. E.↗