SEARCH · Engineering Papers

Results for “LiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1982

LIMS Instrument Package (LIP) balloon experiment: Nimbus 7 satellite correlative temperature, ozone, water vapor, and nitric acid measurements

The Limb Infrared Monitor of the Stratosphere (LIMS) LIP balloon experiment was used to obtain correlative temperature, ozone, water vapor, and nitric acid data at altitudes between 10 and 36 kilometers. The performance of the LIMS sensor flown on the Nimbus 7 Satellite was assessed. The LIP consists of the modified electrochemical concentration cell ozonesonde, the ultraviolet absorption photometric of ozone, the water vapor infrared radiometer sonde, the chemical absorption filter instrument for nitric acid vapor, and the infrared radiometer for nitric acid vapor. The limb instrument package (LIP), its correlative sensors, and the resulting data obtained from an engineering and four correlative flights are described.

Lee, R. B., III↗

NASA NTRS1984

A parametric study of the effect of inlet lip shape upon the radiated sound field

Far field sound radiation predictions for four different axisymmetric inlet lips excited by different tangential acoustic modes at several cut-off ratios are presented. These results were obtained by numerical integration of a special cylindrically symmetric integral representation of the external solutions of the Helmholtz equation which yields unique solutions at all wave numbers. The paper presents plots which detail the dependence of the relative SPL (dB) in the field upon the engine inlet lip shape, the modal input, and the cut-off ratio. Examination of these data indicate that: (1) as the inlet lip becomes larger the predominant acoustic radiation peak in the field becomes narrower and moves towards the centerline of the inlet; (2) as the order of the tangential acoustic mode of the driver increases the radiated sound peak again becomes narrower but moves away from the inlet centerline; and (3) as the cut-off ratio is increased for a specific tangential acoustic mode the predominant radiation peak becomes narrower and moves towards the centerline of the inlet.

Meyer, W. L.↗

NASA NTRS1985

Spillage and flux density on a receiver aperture lip

In a dish-type point-focusing solar thermal collector, the spillage and the flux density on the receiver aperture lip are related in a very simple way, if the aperture is circular and centered on the optical axis. Specifically, the flux density on the lip is equal to the spillage times the peak flux density in the plane of the lip.

Jaffe, L. D.↗

NASA NTRS1991

Effects of nozzle lip geometry on spray atomization and emissions advanced gas turbine combustors

A parametric study is conducted to investigate the effect of nozzle lip geometry on nozzle fuel distribution, emissions and temperature distribution for a rich burn section of a rich burn/quick quench/lean burn combustor. It is seen that the nozzle lip geometry greatly affects the fuel distribution, emissions and temperature distribution. It is determined that at an equivalence ratio of 1.6 the NO concentration could be lowered by a factor greater than three by changing the nozzle lip geometry.

Micklow, Gerald J.↗

NASA NTRS1992

Time resolved simulation of lightning by LIP

Results of time-resolved spectra of lightning simulation in air by laser-induced plasma (LIP) are reported. The measured electron temperatures varied from 17,000 +/-1000 K at 600 ns to 12,000 +/-1000 K at 4 microsec after the ignition of the plasma. Electron densities in the plasma varied from (7.0 +/-1.4) x 10 exp 17/cu cm to (9.0 +/-1.8) x 10 exp 16/cu cm for the above times. A comparison of state variables for LIP and natural lightning is presented. Immediately following the ignition, both natural lightning and LIP are found to reach temperatures in excess of 16,000 K and relax to ambient pressure with different rates. They are expected to approach the 2000-4000-K temperature range, which is important to chemical synthesis, in an asymptotically similar fashion.

Jebens, D. S.↗

NASA NTRS1992

The effects of nozzle exit lip thickness on plume resonance

The acoustic emission and initial shear layer of a cold jet issuing from an underexpanded sonic nozzle were measured where the lip thickness of the nozzle exit varied from 0.015 to 0.625 nozzle diameters. Because the amplitude of plume resonance (or screech) has been shown to be very sensitive to the initial conditions of the plume, the effects of nozzle lip thickness on this sound component in particular was investigated (although it will be shown that other noise components are also affected). Nearfield acoustic measurements have revealed the amplitude and frequency of certain modes of screech to be dependent on nozzle lip thickness. Fluctuating pressure measurements made on the nozzle exit surface have acoustic amplitudes in excess of near field microphone measurements. The dominant mode of instability that exists in the shear layer is also related to this geometric parameter. Detailed shear layer measurements were performed in an attempt to quantify any associated changes in the momentum thickness caused by altering the nozzle exit.

Ponton, M. K.↗

NASA NTRS1993

Analysis of plume backflow around a nozzle lip in a nuclear rocket

The structure of the flow around a nuclear thermal rocket nozzle lip has been investigated using the direct simulation Monte Carlo method. Special attention has been paid to the behavior of a small amount of harmful particles that may be present in the rocket exhaust gas. The harmful fission product particles are modeled by four inert gases whose molecular weights are in a range of 4 131. Atomic hydrogen, which exists in the flow due to the extremely high nuclear fuel temperature in the reactor, is also included. It is shown that the plume backflow is primarily determined by the thin subsonic fluid layer adjacent to the surface of the nozzle lip, and that the inflow boundary in the plume region has negligible effect on the backflow. It is also shown that a relatively large amount of the lighter species is scattered into the backflow region while the amount of the heavier species becomes negligible in this region due to extreme separation between the species. Results indicate that the backscattered molecules are very energetic and are fast-moving along the surface in the backflow region near the nozzle lip.

Chung, Chan H.↗

NASA NTRS1972

Improved lip seal for rotating shafts

Sealing efficiency, service life, and seal loading limits of lip seal for rotating shafts are analyzed. Construction of seal and areas of application are described. Specific advantages of improved lip seal over conventional seals are listed.

Endicott, D. L.↗

NASA NTRS1975

Effect of entry-lip design on aerodynamics and acoustics of high throat Mach number inlets for the quiet, clean, short-haul experimental engine

Results of scale model tests of high-throat-Mach-number inlets designed to suppress inlet-emitted engine machinery noise produced in a V/STOL wind tunnel are presented. A vacuum system was used to induce inlet airflow with a siren as a noise source. Inlet mass flow was 11.68 kilograms (25.75 lb. min) per second at a throat Mach number of 0.79. The effect of entry-lip design (contraction ratio and diameter ratio) on inlet total-pressure recovery, steady-state pressure distortion, performance at high incidence angles, and noise suppression was determined. With proper entry-lip design, total-pressure recovery in excess of 0.988 could be obtained statically at an average throat Mach number of 0.79. Total-pressure distortion was 5 percent. The reduction in the siren tone sound pressure level transmitted through the inlet was 10 to 14 db relative to that measured at throat Mach 0.6.

Miller, B. A.↗

NASA NTRS1977

Wind tunnel tests of the GA(W)-2 airfoil with 20% aileron, 25% slotted flap, 30% Fowler flap and 10% slot-lip spoiler

Two dimensional wind tunnel tests were conducted for the GA(W)-2 airfoil section with: 20% aileron, 25% slotted flap; 30% Fowler flap, and 10% slot-lip spoiler. All tests were conducted at a Reynolds number of 2,200,000 and a Mach Number of 0.13. In addition to force measurements, tuft studies were conducted for the slotted and Fowler flap configurations. Aileron and spoiler hinge moments were obtained by integration of surface pressure measurements. Tests results show that a value of 3.82 was obtained with 30% Fowler flap. Aileron control effectiveness and hinge moments were similar to other airfoils. The slot-lip spoiler provided powerful, positive roll control at all flap settings.

Wentz, W. H., Jr.↗

NASA NTRS1982

Aerodynamic analysis of VTOL inlets and definition of a short, blowing-lip inlet

The results indicated that, without boundary layer control, either a very long inlet or an inlet with a very high contraction ratio lip will be required to meet the stringent design requirements. It is shown that active boundary layer control is an effective means of preventing separation and that a significant reduction in inlet size can be achieved by removing only a small amount of bleed in the throat region of the inlet. A short, blowing-lip model was designed and fabricated. This model features an adjustable, blowing slot located near the hilite on the windward side of the inlet.

Syberg, J.↗

NASA NTRS1982

Wind tunnel tests of a zero length, slotted-lip engine air inlet for a fixed nacelle V/STOL aircraft

Zero length, slotted lip inlet performance and associated fan blade stresses were determined during model tests using a 20 inch diameter fan simulator in the NASA-LeRC 9 by 15 foot low speed wind tunnel. The model configuration variables consisted of inlet contraction ratio, slot width, circumferential extent of slot fillers, and length of a constant area section between the inlet throat and fan face. The inlet performance was dependent on slot gap width and relatively independent of inlet throat/fan face spacer length and slot flow blockage created by 90 degree slot fillers. Optimum performance was obtained at a slot gap width of 0.36 inch. The zero length, slotted lip inlet satisfied all critical low speed inlet operating requirements for fixed horizontal nacelles subsonic V/STOL aircraft.

Woollett, R. R.↗

NASA NTRS1985

Rocket nozzle lip flow by direct simulation Monte Carlo method

The flow in the immediate vicinity of a rocket nozzle lip has been analyzed, and the results are presented. A rapid change in gas composition is observed in the flow around the lip depending principally on species molecular mass and local flow angle. The divergence of axial and radial temperatures indicating breakdown of translational equilibrium is observed in the results.

Hueser, J. E.↗

NASA NTRS1988

Thermostructural analysis with experimental verification in a high heat flux facility of a simulated cowl lip

Three-dimensional FEM analyses using the NASTRAN and MARC codes have been used to predict the thermal and structural response of active cooling schemes proposed for a hypersonic vehicle's propulsion system cowl lip under high aerothermodynamic heating loads. In order to experimentally verify these analyses, a hydrogen/oxygen rocket engine has been modified to employ the exhaust stream as a high enthalpy/high heat flux source for the evaluation of various actively cooled, simulated cowl lip segments as well as flat structural segments.

Melis, Matthew E.↗

NASA NTRS1989

On-orbit results of the LIPS 3/InP homojunction solar cell experiment

The flight performance of NASA Lewis Research Center's indium phosphide homojunction solar cell module on the LIPS 3 satellite is presented. A module of four n+p cells was fabricated and has been on-orbit on the LIPS 3 spacecraft since 1987. The experimental objective is the measurement of InP cell performance in the natural radiation environment of the 1100 kilometer altitude, 60 deg inclination, circular orbit. Flight data from the first year is near expected values, with no degradation in short-circuit current. The temperature dependence of current-voltage parameters is included along with the laboratory radiation tolerance studies necessary for normalization and analysis of the data. Details of the cell structure and flight module design are also discussed.

Brinker, David J.↗

NASA NTRS1993

Direct measurement of capillary blood pressure in the human lip

In this study, we developed and tested a new procedure for measuring microcirculatory blood pressures above heart level in humans. Capillary and postcapillary venule blood pressures were measured directly in 13 human subjects by use of the servonulling micropressure technique adapted for micropuncture of lip capillaries. Pressure waveforms were recorded in 40 separate capillary vessels and 14 separate postcapillary venules over periods ranging from 5 to 64 s. Localization and determination of capillary and postcapillary vessels were ascertained anatomically before pressure measurements. Capillary pressure was 33.2 +/- 1.5 (SE) mm Hg in lips of subjects seated upright. Repeated micropunctures of the same vessel gave an average coefficient of variation of 0.072. Postcapillary venule pressure was 18.9 +/- 1.6 mm Hg. This procedure produces a direct and reproducible means of measuring microvascular blood pressures in a vascular bed above heart level in humans.

Parazynski, S. E.↗

NASA NTRS1935

Development of the NACA slot-lip aileron

An investigation of the undesirable delayed action, or lag, of the spoiler-type lateral control device led to the development of the NACA slot-lip aileron. The tests were made in the 7- by 10-foot wind tunnel with a 4- by 8-foot wing hinged at the tunnel jet boundary and taken of the motion of the control device under test and of the resulting wing motion. First, the lag, as affected by the fore-and-aft location of retractable ailerons or spoilers was determined. The lag was found to increase regularly as the spoiler was moved from the rear of the wing toward the front. Then a combination of spoilers and fixed slot was developed that, with the spoiler retracting into the forward part of the slot, reduced the time lag to a negligible value. In addition, an arrangement was developed using a hinged aileron-type flap as the upper portion, or lip, of a slot through the wing. This arrangement appears to be usable as a form of lateral control device that shows promise of giving improved control and stability at the high angles of attack through stall, with negligible lag, low control forces, and relatively simple construction.

Weick, Fred E↗

NASA NTRS1937

Wind-Tunnel and Flight Tests of Slot-lip Ailerons

The slot-lip ailerons developed by the NACA consist of a flap-type spoiler with an adjoining continuously open slot. The ailerons were developed in an investigation of the delayed response, or lag, of spoiler-type lateral controls. This report presents the results of tests of these slot-lip ailerons made on wing models in the 7 by 10-foot wind tunnel, on a Fairchild 22 airplane in the full-scale wind tunnel and in flight, and on the Weick W1-A airplane in flight.

Shortal, Joseph A↗