Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li plasticity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Anomalously high elastic modulus of a poly(ethylene oxide)-based composite electrolyte

The practical use of lithium metal anodes in solid-state batteries requires a polymer membrane with high lithium-ion conductivity, thermal/electrochemical stability, and mechanical strength. The primary challenge is to effectively decouple the ionic conductivity and mechanical strength of the polymer electrolytes. We report a remarkably facile single step synthetic strategy based on in-situ crosslinking of poly(ethylene oxide) (xPEO) in the presence of a woven glass fiber (GF). Such a simple method yields composite polymer electrolytes (CPE) of anomalously high elastic modulus up to 2.5 GPa over a broad temperature range (20 °C – 245 °C) that has never been previously documented. An unsupervised machine learning algorithm, K-mean clustering analysis, was implemented on the hyperspectral Raman mapping at the xPEO/GF interface. Using such a unique means, we show for the first time that the promoted mechanical strength originates from xPEO and GF interactions through dynamic hydrogen and ionic bonding. High ionic conductivity is achieved by the addition plasticizer (e.g. tetraglyme), where trifluoromethanesulfonate anions are tethered to the xPEO matrix and Li + cations are favorably transported through coordination with the plasticizer. Further, stringent galvanostatic cycling tests indicates the CPE can be stably cycled for >3000 h in a Li-metal symmetric cell at a moderate temperature (nearly 1500 Coulombs/cm 2 Li equivalents), outperforming most of the PEO-based electrolytes. The GF reinforced CPE reported here has multifunctional uses, such as solid electrolytes for all solid-state batteries and membranes for redox-flow batteries. Although the focus of this study is on lithium-based batteries, the results are equally promising for other alkali metal based batteries such as sodium and potassium.

25 ENERGY STORAGE↗
DOE OSTI2025

Comparative analysis of new crystal and plastic scintillators for fast and thermal neutron detection

This paper considers scintillation and physical properties of efficient organic scintillators tested as single crystals and as components of plastics with pulse shape discrimination (PSD). For the first time, single crystals of 9,9-dimethyl-2-phenyl-9H-fluorene (PhF) were grown for studies of the basic scintillation properties of this new compound. Comparison to classical organic crystals, like anthracene, trans-stilbene, and p-terphenyl, and to more recently introduced organic glass showed that the new crystal belongs to a group of the most efficient scintillators, with light output exceeding that of trans-stilbene and PSD comparable to that of p-terphenyl. Furthermore, additional studies were conducted to evaluate scintillation performance and physical properties, like hardness and dye leaching, of plastic scintillators prepared with PhF, organic glass, and liquid diisopropylnaphthalene (DIPN) that were considered as examples for potential replacement of PPO (2,5-diphenyloxazole) in current commercial PSD plastic scintillators. Comparison of the highest performing plastic scintillators prepared with these dyes shows that PhF formulations produced a record light output (LO) increase of 69 % relative to EJ-200. Similar improvements obtained with 6 Li-loaded formulations showed that future development of PSD plastics should not be limited to use of PPO but must involve the search and exploration of new efficient dyes that may lead to discovery of much brighter organic scintillators with improved physical properties required for fast and thermal neutron detection, fast neutron spectroscopy, and antineutrino detection applications.

9,9-dimethyl-2-phenyl-9H-fluorene↗
DOE OSTI2023

Physics-informed machine-learning model of temperature evolution under solid phase processes

We model temperature dynamics during Shear Assisted Proccess Extrusion (ShAPE), a solid phase process that plasticizes feedstock with a rotating tool and subsequently extrudes it into a consolidated tube, rod, or wire. Control of temperature is critical during ShAPE processing to avoid liquefaction, ensure smooth extrusion, and develop desired material properties in the extruded products. Accurate modeling of the complicated thermo-mechanical feedbacks between process inputs, material temperature, and heat generation presents a significant barrier to predictive modeling and process design. In particular, connecting micro-structural scale mechanisms of heat generation to macro-scale predictions of temperature can become computationally intractable. In this work we use a neural network (NN) model of heat generation to bridge this gap, by combining it with a simplified model of the temperature dynamics due to conduction and convection to capture the macro scale evolution of temperature. We inform the construction of the NN heat generation model using crystal plasticity simulations at the micro-structural scale to model the effects of process inputs on generation of heat. We achieved close fits of the temperature dynamics model to a diverse experimental data-set. Further, the relationships learned by the NN model between process inputs and heat generation showed qualitative agreement with those predicted by crystal plasticity simulations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Prismatic-to-basal plastic slip transition in zirconium

Here, we model three-dimensional dislocation ensembles in Zr pillars using newly developed mobility laws for dislocations on prismatic and basal planes. The effects of the loading orientation and temperature on the micro-scale mechanical response of single crystals are systematically explored. Easy dislocation glide is observed on prismatic planes, while hard glide occurs on basal planes. By selection of sample temperature and loading orientation, we show that the transition from prismatic to basal glide of dislocation ensembles can be controlled. We also show that the presence of dislocation cross-slip strongly promotes prismatic glide as a result of prismatic/basal cross-slip energy asymmetry. Cross-slip does not alter the occurrence of plastic slip transition but only induces a shift towards higher temperatures. The preponderance of plastic slip on basal or prismatic planes is found to be mediated by a transitional dislocation, which is composed of glissile segments on parallel prismatic planes connected by glissile super-jogs on basal planes. These findings provide a mechanistic understanding of experiments and highlight the significance of transitional prismatic-basal dislocations on the macroscopic characteristics of plasticity in HCP crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Innovative use of CaO in combination with amino acid salt to convert CO 2 as CaCO 3 nanoparticles under mild pH and low temperature

The increasing demand for sustainable CO 2 management has driven the development of innovative methods that can convert point source CO 2 into value-added products. In this study, CaO in combination with amino acid salt was used to convert CO 2 into CaCO 3 nanoparticles. Different from the conventional method where CO 2 diffusion presents a major challenge in reacting with CaO to form CaCO 3 , amino acid salt solvent was applied to absorb CO 2 first and then rapidly reacted with CaO to form CaCO 3 nanoparticles (∼50 nm) at a low temperature (e.g., 60 °C). Our experiments showed that at a glycine (Gly)/NaOH ratio of 2:1 or 3:1, the solution pH values during the CO 2 absorption and conversion were about 8–9 at 60 °C, while at a ratio of 1:1, the solution pH values were about 9–11; without Gly, the solution pH values were about 12. Gly-optimized solvent substantially reduced corrosion risk to reactors. In addition, the use of amino acid (i.e., Gly) led to much smaller CaCO 3 particles, distinctly different chemical phases, and fundamentally different chemical reactions. Moreover, in the presence of Gly, the solution pH was completely reversed and the solution was regenerated for cyclic use when CaO was added. The solvent was recyclable and reusable, highlighting the cost-effectiveness and sustainability of this approach. The Gly-modulated CaCO 3 nanoparticles may have significant potential for industrial applications in the biomedicine, construction, plastics, and rubber industries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Accelerating ion transport by dynamic asymmetry of alternating polymer electrolytes

Polymer based electrolytes allow the absence of volatile components in batteries thus increasing their safety. Yet, they exhibit drawbacks based on their low conductivity. We have used an alternating polymer consisting of dimethyl siloxane (DMS) and ethylene glycol (EG) blocks to circumvent known disadvantages of the usually used polyethylene glycol (PEG). Incorporating dimethyl siloxane lowers the glass-transition temperature and thus reduces the segmental relaxation time, by dynamic asymmetry or internal plasticization of the constituting polymer blocks. The alternating structure ensures miscibility of the different components and hinders crystallization. Furthermore, the pure polymer, P(DMS 3 -alt-EG 4 ), shows a segmental relaxation time well in the range needed for polymer electrolytes. Mixtures of LiClO 4 and P(DMS 3 -alt-EG 4 ) show a drastically reduced temperature dependence of their DC conductivity in comparison to PEG based systems, resulting in an increase by two orders of magnitude at T = 5 °C and even three to four orders of magnitude at T = 0 °C. Addition of coordinating (acetonitrile) or non-coordinating (toluene) solvent increases conductivity either via additional plasticization or by weakening the Li-binding yet looking at the dynamics at low concentrations of additional solvent the mobility of the polymer is reduced. In conclusion, the solvent addition leads only at higher solvent concentration to a reduction in relaxation time.

Jakobi, Bruno [Louisiana State Univ., Baton Rouge,↗
DOE OSTI2024

Aliphatic Amines from Waste Polyolefins by Tandem Pyrolysis, Hydroformylation, and Reductive Amination

Pyrolysis of waste plastics can produce a product mixture with a high concentration of olefins (>50 wt%). The olefins, as building blocks in the petroleum industry, are potential precursors for valuable commodity chemicals with higher values (>$2000 per ton). In this work, we produce aldehydes by hydroformylation of the olefins present in pyrolysis oil from colored post-consumer recycled high-density polyethylene (PCR-HDPE). The obtained aldehydes in the oil are then converted into aliphatic amines via reductive amination with a Ru/C catalyst. The aminated oil was characterized by multiple analytical chemistry techniques including elemental analysis, nuclear magnetic resonance spectroscopy, high-resolution liquid chromatography-mass spectrometry, and gas chromatography-mass spectrometry with a Polyarc flame ionization detector. The concentration of metals in the PCR-HDPE and oil changes during the tandem processes, showing limited effects of these elements (e.g., Al, Ca, Fe, Mg, Ti, Zn) on hydroformylation and reductive amination. Additionally, we demonstrated that reductive amination of aldehydes with varied carbon numbers and branching properties can be achieved in the presence of a complex mixture, including paraffins and aromatics. The results indicate that waste plastics have the potential to serve as a renewable source for mono and di aliphatic amines, thereby diminishing reliance on fossil feedstocks as the current primary amine source.

aliphatic amines↗
DOE OSTI2021

Phototunable Lignin Plastics to Enable Recyclability

The accumulation of non-degradable petrochemical plastics imposes a significant threat to the environment and ecosystems. We addressed this challenge by designing a new type of phototunable plastics based on the unique lignin chemistry to enable readily end-life recycling. The advanced material design leveraged the efficient photocatalytic lignin depolymerization by ZnO nanoparticles to build lignin-polymethyl methacrylate (PMMA)-ZnO blends. We first demonstrated the highly effective phototunable lignin depolymerization in the complex polymer blend matrix and explored the molecular mechanisms. The technical barriers of mechanical property and recycling processing were then addressed by a new blend design with lignin core grafted with PMMA polymer. The new process has resulted in a new type of PMMA-g-lignin blend, which significantly improved the mechanical properties, making it comparable to PMMA alone. More importantly, the mechanical properties of the UV-treated blend decreased drastically in the new design, whereas the properties did not reduce in the non-grafted blends upon UV exposure. The results highlighted that the new blend design based on graftization maximized the impact of lignin depolymerization on blend structure and recyclability. Based on the results, we developed a process integrating UV and alkaline treatments to recycle PMMA for plastics and fractionated lignin for bioconversion or other applications in the new phototunable plastics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

3D printable polyvinyltoluene-based plastic scintillators with pulse shape discrimination

A feasibility of preparing bulk photopolymerized plastics scintillators that contain vinyltoluene with multifunctional monomers, pentaerythritol tetraacrylate is shown. This formulation offers a simple and fast way to prepare polyvinyltoluene-based plastics with efficient fast neutron/gamma pulse shape discrimination (PSD) within minutes. 30 wt% of 2,5-diphenyloxazole (PPO) was added in the mixtures of vinyltoluene and pentaerythritol tetraacrylate with different secondary dyes to understand the effect of dyes on the scintillation. Prepared resins were photopolymerized under different conditions, and the scintillation performance was compared to a commercially available standard, EJ-276. Additional functionality for thermal neutron sensitivity was introduced by the incorporation of 6 Li and 6 B nuclei. With optimized conditions, prepared plastics showed light output up to 90% relative to the same size of EJ-276. Here, the best plastic scintillators had PSD figures of merit (FoMs) up to 2.77 compared to 3.25 of EJ-276. The 3D-printability of the tested formulations was demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Upcycling of Waste Plastics into Carboxylic Acids for Biodegradable Surfactants

This work outlines a process for producing high‐purity (>95%) carboxylate surfactants from post‐consumer recycled high‐density polyethylene (PCR‐HDPE). The approach involves the thermal depolymerization of PCR‐HDPE via pyrolysis, followed by fractional distillation to isolate C9–C14 olefins. These olefins undergo hydroformylation using cobalt carbonyl catalysts to generate aldehydes, which are subsequently oxidized to carboxylic acids using Pinnick oxidation under mild aqueous‐phase conditions. Neutralization of the resulting carboxylic acids with sodium hydroxide produces plastic‐derived carboxylate surfactants (PDCs) in the form of sodium carboxylates. Subsequent purification steps ensure surfactant‐grade purity and enable accurate assessment of physicochemical properties. The resulting PDCs are evaluated for critical micelle concentration (CMC), foamability, surface tension reduction, and calcium ion tolerance, demonstrating competitive behavior with conventional anionic carboxylate surfactants. This route provides a sustainable alternative for surfactant production, reducing reliance on fossil‐derived feedstocks and valorizing plastic waste streams through chemical upcycling.

Biodegradable surfactants↗
DOE OSTI2023

Effects of rejuvenation modes on the microstructures and mechanical properties of metallic glasses

This study systematically investigates the effects of three rejuvenation modes, namely biaxial loading, thermal pressure loading, and cryogenic thermal cycling, on the microstructures and mechanical properties of Cu 64 Zr 36 metallic glasses (MGs) using molecular dynamics (MD) simulations. The simulation results demonstrate that biaxial tension application during loading results in a rejuvenated glassy state with high strength. Specifically, we find that the yield stress, Young's modulus, and shear modulus of the rejuvenated glass obtained by biaxial tensile loading decreased by 2.8%, 2.1%, and 2.7%, respectively, compared to an as-cast MG reference. We also find that MGs achieve the greatest degree of rejuvenation, at the expense of strength, with the use of thermal pressure loading. Interestingly, the application of cryogenic thermal cycling results in a rejuvenated state with a lower strength drop compared to thermal pressure loading. Furthermore, analysis of the potential energy and medium-range-order (MRO) size indicates that the microstructures of MGs achieves a high-energy ordered glass state after thermal pressure loading, but a high-energy disordered glass state after biaxial tensile loading and cryogenic thermal cycling. Furthermore, these findings provide meaningful insights into the effect of rejuvenation modes on the microstructures and mechanical properties of MGs, as well as useful guidelines for designing MGs with high strength and superior plasticity for prospective applications in industry.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Continuous and discontinuous transitions in the depinning of two-dimensional dusty plasmas on a one-dimensional periodic substrate

We report Langevin dynamical simulations are performed to study the depinning dynamics of two-dimensional dusty plasmas on a one-dimensional periodic substrate. From the diagnostics of the sixfold coordinated particles P 6 and the collective drift velocity V x , three different states appear, which are the pinning, disordered plastic flow, and moving ordered states. It is found that the depth of the substrate is able to modulate the properties of the depinning phase transition, based on the results of P 6 and V x , as well as the observation of hysteresis of V x while increasing and decreasing the driving force monotonically. When the depth of the substrate is shallow, there are two continuous phase transitions. When the potential well depth slightly increases, the phase transition from the pinned to the disordered plastic flow states is continuous; however, the phase transition from the disordered plastic flow to the moving ordered states is discontinuous. When the substrate is even deeper, the phase transition from the pinned to the disordered plastic flow states changes to discontinuous. When the depth of the substrate further increases, as the driving force increases, the pinned state changes to the moving ordered state directly, so that the disordered plastic flow state disappears completely.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Multiscale modeling of shear banding in metallic glasses (Final report)

Metallic glasses (MGs) possess remarkably high strength but suffer from minimal tensile ductility due to the formation of catastrophic shear bands. The goal of this research project is to develop an understanding of the microstructures and deformation mechanisms that control shear banding in MGs, which will enable the development of MGs with enhanced plasticity. Two scientific objectives have been pursued. (1) Understand the underlying mechanisms of shear banding phenomena in presence of nanoscale heterogeneities in MGs. (2) Understand the evolution of MG heterogenous structure upon thermomechanical stimuli for plasticity enhancement through controlling and distributing multiple shear bands.

36 MATERIALS SCIENCE↗