Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LTO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Evaluation of a staged fuel combustor for turboprop engines

Proposed EPA emission regulations require emission reduction by 1979 for various gas turbine engine classes. Extensive combustion technology advancements are required to meet the proposed regulations. The T56 turboprop engine requires CO, UHC, and smoke reduction. A staged fuel combustor design was tested on a combustion rig to evaluate emission reduction potential in turboprop engines from fuel zoning. The can-type combustor has separately fueled-pilot and main combustion zones in series. The main zone fueling system was arranged for potential incorporation into the T56 with minor or no modifications to the basic engine. Three combustor variable geometry systems were incorporated to evaluate various airflow distributions. Emission results with fixed geometry operation met all proposed EPA regulations over the EPA LTO cycle. CO reduction was 82 percent, UHC reduction was 96 percent, and smoke reduction was 84 percent. NOx increased 14 percent over the LTO cycle. At high power, NOx reduction was 40 to 55 percent. This NOx reduction has potential application to stationary gas turbine powerplants which have different EPA regulations.

Verdouw, A. J.↗
NASA NTRS2014

Multi-Point Combustion System: Final Report

A low-NOx emission combustor concept has been developed for NASA's Environmentally Responsible Aircraft (ERA) program to meet N+2 emissions goals for a 70,000 lb thrust engine application. These goals include 75 percent reduction of LTO NOx from CAEP6 standards without increasing CO, UHC, or smoke from that of current state of the art. An additional key factor in this work is to improve lean combustion stability over that of previous work performed on similar technology in the early 2000s. The purpose of this paper is to present the final report for the NASA contract. This work included the design, analysis, and test of a multi-point combustion system. All design work was based on the results of Computational Fluid Dynamics modeling with the end results tested on a medium pressure combustion rig at the UC and a medium pressure combustion rig at GRC. The theories behind the designs, results of analysis, and experimental test data will be discussed in this report. The combustion system consists of five radially staged rows of injectors, where ten small scale injectors are used in place of a single traditional nozzle. Major accomplishments of the current work include the design of a Multipoint Lean Direct Injection (MLDI) array and associated air blast and pilot fuel injectors, which is expected to meet or exceed the goal of a 75 percent reduction in LTO NOx from CAEP6 standards. This design incorporates a reduced number of injectors over previous multipoint designs, simplified and lightweight components, and a very compact combustor section. Additional outcomes of the program are validation that the design of these combustion systems can be aided by the use of Computational Fluid Dynamics to predict and reduce emissions. Furthermore, the staging of fuel through the individually controlled radially staged injector rows successfully demonstrated improved low power operability as well as improvements in emissions over previous multipoint designs. Additional comparison between Jet- A fuel and a hydrotreated biofuel is made to determine viability of the technology for use with alternative fuels. Finally, the operability of the array and associated nozzles proved to be very stable without requiring additional active or passive control systems. A number of publications have been publish

Goeke, Jerry↗
NASA NTRS2014

NASA N3-X with Turboelectric Distributed Propulsion

Presentation summarizing the phase I study of the NASA N3-X turboelectric distributed propulsion power aircraft to the IMechE Disruptive Green Propulsion Technologies conference in London, UK November 16th and 17th, 2014. This presentation contains the results of a NASA internal study funded by the NASA Fixed Wing program to look at the application of turboelectric distributed propulsion to a long-range 300 seat aircraft. The reference aircraft is the Boeing 777-200LR. The N3-X reduced energy consumption by 70 compared to the 777-200LR, LTO NOx by 85 compared to the CAEP 6 limits, and noise by 32-64 EPNdB depending on engine placement compared to the stage 4 noise standards. This exceeded the N+3 metrics of reducing energy by 60, LTO NOx by 80, and noise by 52 EPNdB. Cruise NOx was not estimated, but likely meet the 80 reduction goal as well.

propulsion↗
NASA NTRS2015

Development of Advanced Low Emission Injectors and High-Bandwidth Fuel Flow Modulation Valves

Parker Hannifin Corporation developed the 3-Zone fuel nozzle for NASA's Environmentally Responsible Aviation Program to meet NASAs target of 75 LTO NOx reduction from CAEP6 regulation. The nozzle concept was envisioned as a drop-in replacement for currently used fuel nozzle stem, and is built up from laminates to provide energetic mixing suitable for lean direct injection mode at high combustor pressure. A high frequency fuel valve was also developed to provide fuel modulation for the pilot injector. Final testing result shows the LTO NOx level falling just shy of NASAs goal at 31.

control↗
NASA NTRS2016

Application of Deterministic and Probabilistic System Design Methods and Enhancements of Conceptual Design Tools for ERA Project

This report documents work done by the Aerospace Systems Design Lab (ASDL) at the Georgia Institute of Technology, Daniel Guggenheim School of Aerospace Engineering for the National Aeronautics and Space Administration, Aeronautics Research Mission Directorate, Integrated System Research Program, Environmentally Responsible Aviation (ERA) Project. This report was prepared under contract NNL12AA12C, "Application of Deterministic and Probabilistic System Design Methods and Enhancement of Conceptual Design Tools for ERA Project". The research within this report addressed the Environmentally Responsible Aviation (ERA) project goal stated in the NRA solicitation "to advance vehicle concepts and technologies that can simultaneously reduce fuel burn, noise, and emissions." To identify technology and vehicle solutions that simultaneously meet these three metrics requires the use of system-level analysis with the appropriate level of fidelity to quantify feasibility, benefits and degradations, and associated risk. In order to perform the system level analysis, the Environmental Design Space (EDS) [Kirby 2008, Schutte 2012a] environment developed by ASDL was used to model both conventional and unconventional configurations as well as to assess technologies from the ERA and N+2 timeframe portfolios. A well-established system design approach was used to perform aircraft conceptual design studies, including technology trade studies to identify technology portfolios capable of accomplishing the ERA project goal and to obtain accurate tradeoffs between performance, noise, and emissions. The ERA goal, shown in Figure 1, is to simultaneously achieve the N+2 benefits of a cumulative noise margin of 42 EPNdB relative to stage 4, a 75 percent reduction in LTO NOx emissions relative to CAEP 6 and a 50 percent reduction in fuel burn relative to the 2005 best in class aircraft. There were 5 research task associated with this research: 1) identify technology collectors, 2) model technology collectors in EDS, 3) model and assess ERA technologies, 4) LTO and cruise emission prediction, and 5) probabilistic analysis of technology collectors and portfolios.

Mavris, Dimitri N.↗
NASA NTRS2017

N+2 Advanced Low NOx Combustor Technology Final Report

In accordance with NASAs technology goals for future subsonic vehicles, this contract identified and developed new combustor concepts toward meeting N+2 generation (2020) LTO (landing and take-off) NOx emissions reduction goal of 75 from the standard adopted at Committee on Aviation Environmental Protection 6 (CAEP6). Based on flame tube emissions, operability, and autoignition testing, one concept was down selected for sector testing at NASA. The N+2 combustor sector successfully demonstrated 75 reduction for LTO NOx (vs. CAEP6) and cruise NOx (vs. 2005 B777-200 reference) while maintaining 99.9 cruise efficiency and no increase in CO and HC emissions.The program also developed enabling technologies for the combustion system including ceramic matrix composites (CMC) liner materials, active combustion control concepts, and laser ignition for improved altitude relight.

era↗
NASA NTRS2020

Emission Characteristics of an Axially Staged Sector Combustor for a Small Core High OPR Subsonic Aircraft Engine

This paper presents the nitrogen oxides, carbon monoxide, and particulate matter emissions of a single sector axially staged combustor sector designed and fabricated by United Technologies Research Center (UTRC) in partnership with NASA under a compact low-emissions combustor contract supported by the NASA Advanced Air Transport Technology (AATT) N+3 project. The test was conducted at NASA Glenn Research Center's CE-5 combustion test facility. The facility provided inlet air temperatures up to 922 K and pressures up to 19.0 bar. The combustor design concept, called Axially Controlled Stoichiometry (ACS), was developed by Pratt & Whitney (P&W) under NASA's Environmentally Responsible Aviation (ERA) program for an N+2 combustor for use in twin-aisle subsonic aircraft engines. Under the N+3 project the ACS combustor was scaled-down for application to small-core N+3 engines for use in single-aisle aircraft. The results show that the NOx and CO emissions characteristics are similar in both the N+2 and N+3 applications. The non-volatile particulate matter (nvPM) emissions trends are similar to CO emissions with an exception at high fuel-air ratio, as inlet air temperature and pressure conditions change from taxi to approach. Three NOx correlation equations are generated to describe theNOx emissions of this combustor. The percentage landing and takeoff (LTO) NOx reduction of the N+3 ACS combustor is between 82% and 89% relative to the ICAO CAEP/6 standard, which meets the NASA N+3 goal of exceeding 80% LTO NOx reduction.

He, Zhuohui J.↗
NASA NTRS2024

Flow, Noise and Thrust of Supersonic Plug Nozzles

A model-scale experimental study is conducted with a plug nozzle exploring the performance of various plug geometries for supersonic aircraft concepts. All data are acquired with a given outer nozzle that is convergent and has an exit diameter of 2 inches. The shape of the centrally placed plug is varied from conic with various half-angles (lengths), to method of characteristics (MoC) designs, as well as truncated and porous geometries. Noise and schlieren flow visualization data, presented in an earlier paper, are briefly reviewed first. The focus in this paper is on the thrust performance. A newly constructed thrust stand is used to acquire data covering a nozzle pressure ratio (NPR) range from transonic (‘landing and takeoff’, LTO) to supersonic (‘cruise’) conditions. Back-to-back measurements allowed assessment of relative performance. A plug with its ‘crown’ located somewhat inside the nozzle, rather than near the exit, is found to perform better. A longer 10° plug performs better than a shorter 22° plug. A porous plug, that significantly suppresses broadband shock associated noise, is found to incur a modest thrust loss that might be an acceptable tradeoff near LTO conditions. A companion numerical simulation for some of the plug geometries yields data trends bearing reasonable agreement with the experimental results.

jets↗
NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗
NASA NTRSDate not supplied

Study of a Plug Nozzle for Supersonic Aircraft Concepts

A plug nozzle with a cylindrical cowl is studied. The geometry is adopted following commercial supersonic aircraft concepts considered in an ongoing NASA program. For the given cowl, the plug geometry is varied that includes shapes developed by a numerical optimization study as well as porous plugs. Experimental data on noise and flow field are discussed with an eye for minimum noise at low nozzle pressure ratios (NPR2) representing landing and takeoff (LTO) conditions. NPR up to about 4.7 is covered in the experiments. Limited thrust data with accompanying numerical simulation results are also presented. Results show that a plug designed for optimum thrust at cruise is noisier while a plug designed for optimum thrust at LTO has less noise, throughout the NPR range covered. The results also show that a plug nozzle can generate transonic tones and excess broadband noise (EBBN) at lower NPR, apart from well-known screech tones and broadband shock associated noise (BBSN) at higher NPR. A long porous plug is found to effectively suppress all these aberrant noise components while suffering less than 1% loss in thrust coefficient.

Jets↗
NASA NTRSDate not supplied

Reduction of Aircraft Noise Uncertainty for a Notional Supersonic Business Jet

NASA supported a study by the International Civil Aviation Organization on the environmental impact of adding supersonic aircraft to the existing global fleet by designing a notional 55-tonne supersonic business jet. The aircraft is referred to as the Supersonic Technology Concept Aeroplane (STCA) and has been used in a multitude of studies over the past few years. One of the many studies on this aircraft was the noise produced by the STCA during landing and take-off (LTO) operations. The LTO noise for the STCA was assessed using contemporary noise prediction tools that have been primarily developed for and utilized by subsonic aircraft, resulting in a high level of uncertainty for the STCA noise predictions. NASA has recently been conducting research and developing tools to reduce the uncertainty for airport noise predictions of supersonic aircraft. The initial focus of the uncertainty reduction was on the jet and inlet-radiated fan noise produced by supersonic engine systems since these sources are dominant during take-off and landing operations for supersonic jets. The results of these efforts are discussed and applied to the STCA model to update the airport noise predictions and associated uncertainty metrics. It is shown that by using new noise source prediction models, the overall system-level cumulative noise uncertainty of the study vehicle is reduced from a standard deviation of 7.8 EPNdB to 2.0 EPNdB.

uncertainty↗
DOE OSTI2025

Laser ablation of high-loading Li-ion battery electrodes improves accessible capacity and cycle life for Behind-the-Meter Storage

Adoption of Behind-the-Meter Storage (BTMS) requires design of batteries that enable high safety, long cycle life, and low cost at the system level. Pairing Li 4 Ti 5 O 12 (LTO) with LiMn 2 O 4 (LMO) achieves targets related to safety and cycle life, but these materials' low energy densities contribute to higher cost at the system scale. Increasing electrode loading is a simple approach to improve energy density, but comes with a trade-off in electrode utilization due to long, tortuous Li + diffusion pathways. Here, laser ablation is used to microstructure (pattern) high-loading electrodes to enhance electrode performance through improved Li + diffusion pathways. Four cell types, comprising combinations of standard or patterned anode and cathode, were prepared to evaluate the effects of laser ablation at each electrode. A rate test shows that patterning electrodes enhances active material utilization at ≳1C rates. Patterning the cathode yields the most benefit, as cells with a patterned cathode demonstrate a ~20% higher accessible capacity than those without at 1.4C. Additionally, 1C capacity retention of cells with patterned cathode (91% through 3000 cycles) is significantly improved over cells with only the anode patterned (64%) and non-patterned electrodes (50%). Characterization of post-mortem cells before and after refreshing their electrolyte suggests that 1C capacity retention is improved by mitigation of electrode "dry-out". We hypothesize that the microstructure acts as a reservoir of additional electrolyte, or a path for gas to escape, so that active material remains wetted throughout long-term cycling, and/or the microstructure may reduce localized, gas-forming overpotentials in the high-loading electrode.

25 ENERGY STORAGE↗
DOE OSTI2024

Heterogeneous Organochromium Catalysts for Stereoselective Isoprene Polymerization

In this study, heterogeneous organochromium catalysts have been developed via surface lithiation of traditional surface organometallic complexes to mediate stereoselective isoprene polymerization. Chemisorption of the molecular complex Cr(CH 2 SiMe 3 ) 4 on high surface area anatase titania nanoparticles as well as on a silica support led to the bipodal complexes Cr/TiO 2 and Cr/SiO 2 , respectively. Subsequent reductive lithium intercalation with n-butyllithium led to the formation of lower valent Cr 2+ species Cr/LTO and Cr/Li/SiO 2 . Alternatively, Cr(CH 2 SiMe 3 ) 4 was allowed to react with nBuLi-reduced anatase titania (LTO) to provide Cr/LTO Inv . Cr/LTO and Cr/Li/SiO 2 both polymerize isoprene with very high activities (154 and 174 kg molCr –1 h –1 , respectively) to provide polyisoprene with cis-1,4 selectivity up to 82% in toluene at 50 °C. On the other hand, Cr/SiO 2 provides polyisoprene with excellent trans-1,4 selectivity up to 98% (16 kg molCr –1 h –1 ), and Cr/TiO 2 was catalytically inactive. Cr/LTO Inv is less active and selective, and X-ray absorption spectroscopy (XAS) measurements of the precatalyst revealed the presence of a mixture of metallic Cr 0 , Cr 4+ , and only minor Cr 2+ species. Thus, surface lithiation can promote the formation of lower valent metal centers which enable stereocontrol in isoprene polymerizations and may be extended as a general protocol to other catalytic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1976

Pollution Reduction Technology Program, Turboprop Engines, Phase 1

Exhaust pollutant emissions were measured from a 501-D22A turboprop engine combustor and three low emission combustor types -- reverse flow, prechamber, and staged fuel, operating over a fuel-air ratio range of .0096 to .020. The EPAP LTO cycle data were obtained for a total of nineteen configurations. Hydrocarbon emissions were reduced from 15.0 to .3 lb/1000 Hp-Hr/cycle, CO from 31.5 to 4.6 lb/1000 Hp-Hr/cycle with an increase in NOx of 17 percent, which is still 25% below the program goal. The smoke number was reduced from 59 to 17. Emissions given here are for the reverse flow Mod. IV combustor which is the best candidate for further development into eventual use with the 501-D22A turboprop engine. Even lower emissions were obtained with the advanced technology combustors.

Anderson, R. D.↗
NASA NTRS1977

Evaluation of commercial pyroelectric detectors

A series of commercially available pyroelectric detectors made from PVF2, LTO, SBN, and TGS were evaluated in terms of responsivity and detectivity as a function of frequency. The performance of the detectors evaluated was very different, depending upon the manufacturer of the detector, and this dependency was primarily related to the thickness of the various detectors. The best detectors of each material were comparable in performance at frequencies around 10 Hz but differed radically at frequencies above 100 Hz.

Robertson, J. B.↗
NASA NTRS1980

The geology and morphology of Ina

The lunar feature Ina, an unusual D-shaped depression, is located in Lacus Felicitatis north of Mare Vaporum. Attention was drawn to the feature because of its strange 'blistered' appearance. Using detailed topographic data available from the Lunar Topographic Orthophotomap (LTO) series, it is now possible to depict the morphology and structure of Ina and the surrounding region more accurately than was previously feasible. The maps employed in the study are 41C3 and 41C4 at 1:250,000 scale, and 41C3S1 (Ina) at 1:10,000 scale. Attention is given to the regional setting, and the morphologic characteristics and origins of features. It is concluded that Ina is an apparently unique volcanic feature. It rests on a dome displaying evidence of episodic extrusive activity. Its odd D-shape is probably related to a local fracture pattern, since the straight edge is aligned with other small lineaments in the area. Ina's floor exhibits several volcanic units.

Strain, P. L.↗
NASA NTRS2002

Overview of NASA's UEET Program

This paper presents a general overview of NASA's Ultra Efficient Engine Technology (UEET) Program. The program's vision is to develop and hand off revolutionary turbine engine propulsion technologies that will enable future generation vehicles over a wide range of flight speeds. The specific goals include: 1) Perform propulsion technologies to enable increases in system efficiency and, therefore, fuel burn reductions of up to 15% (equivalent reductions in CO2); and 2) Provide combustor technologies (configuration and materials) which will enable reductions in Landing/Take-off (LTO) NOx of 70% relative to 1996 ICAO standards.

Shaw, Robert J.↗