Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interface properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

The effects of nanoscale confinement on the behavior of metal laminates

By reducing the layer thickness, h, in metal multilayers from micrometer- to nanometer-levels, scale-dependent transitions in behavior are observed. The role of interface properties in these transitions has been extensively investigated. However, reducing h to the nanoscale regime also imposes a physical geometric confinement on defect-related processes occurring within the layers, an effect that is relatively less explored. Herein, we present illustrative examples of the influence of nanoconfinement on the strength, structure, and radiation response of multilayers. These examples show that nanoconfinement and interface structure and topology act cooperatively in the nanoscale limit, affecting behaviors that cannot be explained based on either factor alone.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Degradation behavior of CIGS solar Cells: A parametric analysis

A parametric study of the effect of bulk and interface properties on device characteristics as a function of heat and light stress under open-circuit and short-circuit conditions is developed for Cu(In,Ga)(S,Se) 2 solar cells using SCAPS-1D simulator. The variables and interdependencies modeled include: (1) conduction band offset (CBO) between buffer and absorber; (2) buffer ionized donor density; (3) CIGS shallow acceptor density; (4) CIGS deep acceptor density; (5) CIGS shallow donor density; (6) ionized acceptor concentration in the ordered vacancy compound (OVC) CIGS/buffer interface; and (7) back contact work-function. An increase in absorber shallow acceptor or a decrease in shallow donor density results in an increase in net carrier density and open-circuit voltage (V OC ). Further, a decrease in V OC is observed with an increase in the deep acceptors or neutral midgap defects in the CIGS due to higher charge carrier recombination. A change of CBO from spike to cliff condition is a dominant mechanism of decreasing VOC with an interface defect density of 10 12 cm -2 . The minimum depletion width is found to be specifically sensitive to CBO and interface defect density. An inflection in the capacitance–voltage curves (in reverse bias) is observed with simultaneous increase in bulk deep acceptor density and shallow donor density near the back contact.

14 SOLAR ENERGY↗
DOE OSTI2024

Relating Hydro–Mechanical and Elastodynamic Properties of Dynamically Stressed Tensile–Fractured Rock in Relation to Applied Normal Stress, Fracture Aperture, and Contact Area

We exploit nonlinear elastodynamic properties of fractured rock to probe the micro-scale mechanics of fractures and understand the relation between fluid transport and fracture aperture under dynamic stressing. Experiments were conducted on rough, tensile-fractured Westerly granite subject to triaxial stresses. We measure fracture permeability for steady-state fluid flow with deionized water. Pore pressure oscillations are applied at amplitudes ranging from 0.2 to 1 MPa at 1 Hz frequency. During dynamic stressing we transmit ultrasonic signals through the fracture using an array of piezoelectric transducers (PZTs) to monitor evolution of interface properties. We examine the influence of fracture aperture and contact area by conducting measurements at effective normal stresses of 10–20 MPa. Additionally, the evolution of contact area with stress is characterized using pressure sensitive film. These experiments are conducted separately with the same fracture and map contact area at stresses from 9 to 21 MPa. The measurements are a proxy for “true” contact area for the fracture surface and we relate them to elastic properties using the calculated PZT sensor footprints via numerical modeling of Fresnel zones. We compare the elastodynamic response of the fracture using the stress-induced changes in ultrasonic wave velocities for transmitter-receiver pairs to image spatial variations in contact properties. We show that nonlinear elasticity and permeability enhancement decrease with increasing normal stress. Additionally, post-oscillation wave velocity and permeability exhibit quick recoveries toward pre-oscillation values. Estimates of fracture contact area (global and local) demonstrate that the elastodynamic and permeability responses are dominated by fracture topology.

58 GEOSCIENCES↗
DOE OSTI2021

Carrier gradients and the role of charge selective contacts in lateral heterojunction all back contact perovskite solar cells

Realizing photovoltaic devices that achieve the full potential of the metal halide perovskite material will require improved insight regarding the role of selective contacts and how key interfaces operate when mobile defects are present. However, measuring interface properties in typical device stacks where the perovskite layer is thin and sandwiched between two contacts has been a challenge. Here, we fabricate p-i-n and p-n lateral heterojunctions with nickel oxide/titanium oxide all back contacts, permitting us to employ a comprehensive analysis approach, including ultraviolet and X-ray photoemission spectroscopy (UPS/XPS), angle-resolved X-ray absorption spectroscopy (XAS), Kelvin probe force microscopy (KPFM), surface photovoltage (SPV), hyperspectral imaging (HSI), and time-resolved fluorescence lifetime imaging microscopy (TR-FLIM) to discern the role of selective contacts. Specifically, we tune the selectivity of the contacts, changing the gradient in the carrier concentration across the surface of the active layer, which is connected to carrier extraction at the buried interface, and thus the device functionality.

25 ENERGY STORAGE↗
DOE OSTI2024

Charge Transfer in 2D Halide Perovskites and 2D/3D Heterostructures

Halide perovskites have emerged as a versatile class of materials, with applications spanning photovoltaics, light-emitting diodes, transistors, and photodetectors. The introduction of semiconducting ligands to form two-dimensional (2D) perovskites on the surface of three-dimensional (3D) perovskites in perovskite solar cells has been shown to enhance the performance and stability. To improve the interface properties between the 3D perovskite layer and charge carrier transport layers, understanding the charge transfer (CT) process in 2D perovskites is crucial. In this Perspective, we address common terminological inaccuracies in energy level descriptions, delineate methods for energy alignment characterization, and present practical instances of CT in 2D perovskite-incorporated solar cells. Furthermore, we emphasize the significance of precise terminology, appropriate measurement techniques, and rational design of 2D ligands to harness the full potential of 2D perovskites in optoelectronic applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Advances in SnO 2 for Efficient and Stable n-i-p Perovskite Solar Cells

Perovskite solar cells (PSCs) based on the regular n-i-p device architecture have reached above 25% certified efficiency with continuously reported improvements in recent years. A key common factor for these recent breakthroughs is the development of SnO 2 as an effective electron transport layer in these devices. In this review, we discuss the key advances in SnO 2 development, including various deposition approaches and surface treatment strategies, to enhance the bulk and interface properties of SnO 2 for highly efficient and stable n-i-p PSCs. We also discuss the general materials chemistry associated with SnO 2 along with the corresponding materials challenges and improvement strategies, focusing on defects, intrinsic properties, and impact on device characteristics. Finally, we highlight some SnO2 implementations related to scalable processes and flexible devices, and we also provide our perspective on the future development of efficient and stable large-scale perovskite solar modules.

14 SOLAR ENERGY↗
DOE OSTI2024

Optical Diagnostics of Discharges in and in Contact With Liquids

Discharges in liquids have been the subject of intensive investigations for a broad range of applications and involve highly coupled and complex phenomena with timescales ranging from picoseconds to seconds and length scales from micrometers to centimeters. This review focuses on some of the challenges in optical diagnostics of discharges in and in contact with liquids; this includes the interpretation of optical emission spectra, the inherently stochastic nature of many discharge phenomena including the initial stages of plasma ignition, and the large gradients in species and plasma properties interfacing with a dynamic liquid interface. We report recent notable advances, controversies in interpretations of diagnostics, and remaining opportunities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Advances and perspectives on mass transfer and enzymatic hydrolysis in the enzyme-mediated lignocellulosic biorefinery: A review

We report enzymatic hydrolysis is a critical process for the cellulase-mediated lignocellulosic biorefinery to produce sugar syrups that can be converted into a whole range of biofuels and biochemicals. Such a process operating at high-solid loadings (i.e., scarcely any free water or roughly ≥ 15% solids, w/w) is considered more economically feasible, as it can generate a high sugar concentration at low operation and capital costs. However, this approach remains restricted and incurs “high-solid effects”, ultimately causing the lower hydrolysis yields with increasing solid loadings. The lack of available water leads to a highly viscous system with impaired mixing that exhibits strong transfer resistance and reaction limitation imposed on enzyme action. Evidently, high-solid enzymatic hydrolysis involves multi-scale mass transfer and multi-phase enzyme reaction, and thus requires a synergistic perspective of transfer and biotransformation to assess the interactions among water, biomass components, and cellulase enzymes. Porous particle characteristics of biomass and its interface properties determine the water form and distribution state surrounding the particles, which are summarized in this review aiming to identify the water-driven multi-scale/multi-phase bioprocesses. Further aided by the cognition of rheological behavior of biomass slurry, solute transfer theories, and enzyme kinetics, the coupling effects of flow-transfer-reaction are revealed under high-solid conditions. Based on the above basic features, this review lucidly explains the causes of high-solid hydrolysis hindrances, highlights the mismatched issues between transfer and reaction, and more importantly, presents the advanced strategies for transfer and reaction enhancements from the viewpoint of process optimization, reactor design, as well as enzyme/auxiliary additive customization.

45 multi-scale, multi-phase, enzymatic reaction↗
DOE OSTI2023

Fission gas retention of densely packed uranium carbonitride tristructural-isotropic fuel particles in a 3D printed SiC matrix

The Transformational Challenge Reactor (TCR) fuel form was designed to contain large, densely packed uranium carbonitride (UCN) tristructural-isotropic (TRISO) fuel particles within a 3D printed SiC matrix, increasing the uranium density compared to conventional TRISO fuel forms and offering full geometric freedom for core design. Here, this work summarizes initial low-burnup, high-power irradiation testing of TCR fuel materials, including loose UCN TRISO particles and integral fuel compacts with ~55% TRISO particles by volume, to evaluate fission gas retention. Fission gasses were fully retained in all loose particle tests and in integral compacts irradiated at low (<250 °C) surface temperatures. Initial testing at higher (~700–750 °C) fuel surface temperatures showed fission gas release (FGR) and complete fracture of three compacts, but no FGR was observed in later high temperature tests (~300–750 °C) of both fueled compacts and loose TRISO particles. Calculated thermal stresses in the failed compacts were far less than the measured strength of the SiC matrix and the stresses in some failed compacts were less than those in compacts that did not show FGR. Thermal stress-induced matrix cracks also would not cause complete fracture because the tensile stresses transition to compression in the higher temperature regions. Therefore, fuel failure was likely not caused by thermal stresses and may have been related to leakage currents from the electrical heaters and erratic fuel surface temperatures that were only observed in the test for which failure was observed. In any case, the matrix cracks propagated through the coatings of TRISO particles located in the high-density matrix regions on the peripheries of the compacts, resulting in measurable fission gas release. The discussion focuses on the importance of understanding matrix density distributions and the particle-matrix interface properties to prevent matrix cracks from causing TRISO particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Atomic-Scale Andreev Probe of Unconventional Superconductivity

Recent emergence of low-dimensional unconventional superconductors and their exotic interface properties calls for new approaches to probe the pairing symmetry, a fundamental and frequently elusive property of the superconducting condensate. Here, we introduce the unique capability of tunneling Andreev reflection (TAR) to probe unconventional pairing symmetry, utilizing the sensitivity of this technique to specific Andreev reflections. Specifically, suppression of the lowest-order Andreev reflection due to quantum interference but emergence of the higher-order Andreev processes provides direct evidence of the sign-changing order parameter in the paradigmatic FeSe superconductor. Furthermore, TAR spectroscopy also reveals two superconducting gaps, points to a possibility of a nodal gap structure, and directly confirms that superconductivity is locally suppressed along the nematic twin boundary, with preferential and near-complete suppression of the larger energy gap. Furthermore, our findings therefore enable new, atomic-scale insight into microscopic, inhomogeneous, and interfacial properties of emerging quantum materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Molecular Diradical Spin Qubits in a Crystalline Host as a Platform for Quantum Sensing

Doping a luminescent tris(2,4,6-trichlorophenyl)methyl diradical m (TTM) 2 into a host crystal of its diamagnetic precursor m (HTTM) 2 creates a molecular color center with enhanced optical-spin interface properties important for quantum sensing. Optical polarization of the |T 0 ⟩ sublevel of the diradical triplet ground state is achieved by spin-selective intersystem crossing from the |T + ⟩ and |T – ⟩ sublevels of the triplet excited state at ambient and cryogenic temperatures. Coherent spin control of m (TTM) 2 doped into m (HTTM) 2 using pulsed optically detected magnetic resonance (ODMR) spectroscopy results in a 10-fold improvement in ODMR contrast over that observed for randomly oriented m (TTM)2 using continuous-wave ODMR. The diradical doped crystal powders achieve spin coherence times of 2.8, 3.4, and 7.4 μs at 294, 85, and 5 K, respectively. The diradical photoluminescence is sensitive to weak applied magnetic fields independent of temperature, excitation wavelength, and dopant concentration, providing a promising pathway toward robust quantum sensing of anisotropic magnetic fields under ambient conditions.

crystal structure↗
DOE OSTI2025

Bond-centric modular design of protein assemblies

Directional interactions that generate regular coordination geometries are a powerful means of guiding molecular and colloidal self-assembly, but implementing such high-level interactions with proteins remains challenging due to their complex shapes and intricate interface properties. Here we describe a modular approach to protein nanomaterial design inspired by the rich chemical diversity that can be generated from the small number of atomic valencies. We design protein building blocks using deep learning-based generative tools, incorporating regular coordination geometries and tailorable bonding interactions that enable the assembly of diverse closed and open architectures guided by simple geometric principles. Experimental characterization confirms the successful formation of more than 20 multicomponent polyhedral protein cages, two-dimensional arrays and three-dimensional protein lattices, with a high (10%–50%) success rate and electron microscopy data closely matching the corresponding design models. Due to modularity, individual building blocks can assemble with different partners to generate distinct regular assemblies, resulting in an economy of parts and enabling the construction of reconfigurable networks for designer nanomaterials.

Biomaterials – proteins↗
DOE OSTI2023

A new approach to the design of surface subsystems of polymeric insulators for HV and MV apparatus under AC voltage

The design of high voltage and medium voltage AC and DC standoff insulators, and, in general, of insulation systems where surface and interface properties are predominant factors, is based on specifications and standards that rely upon long-term experiences and lab testing. Surface insulating properties depend on electrical and thermal stresses, besides environmental factors, and the inception of extrinsic ageing phenomena, such as partial discharges, can be already a cause of reduced reliability and premature failure (for organic insulating materials). An innovative approach, based on field simulation, discharge modelling, and partial discharge inception measurements is presented by the authors, which can establish a solid basis to optimise insulation design for any type of supply voltage waveform. This method, the three-leg approach, is applied here to a cable system under AC sinusoidal voltage, but it can work for any type of insulation system, such as bushings, switch gears, transformers, rotating machines, and power electronics boards.

42 ENGINEERING↗
DOE OSTI2021

Role of transferred graphene on atomic interaction of GaAs for remote epitaxy

Remote epitaxy is a recently discovered type of epitaxy, wherein single-crystalline thin films can be grown on graphene-coated substrates following the crystallinity of the substrate via remote interaction through graphene. Although remote epitaxy provides a pathway to form freestanding membranes by controlled exfoliation of grown film at the graphene interface, implementing remote epitaxy is not straightforward because atomically precise control of interface is required. Here, we unveil the role of the graphene–substrate interface on the remote epitaxy of GaAs by investigating the interface at the atomic scale. By comparing remote epitaxy on wet-transferred and dry-transferred graphene, we show that interfacial oxide layer formed at the graphene–substrate interface hinders remote interaction through graphene when wet-transferred graphene is employed, which is confirmed by an increase of interatomic distance through graphene and also by the formation of polycrystalline films on graphene. On the other hand, when dry-transferred graphene is employed, the interface is free of native oxide, and single-crystalline remote epitaxial films are formed on graphene, with the interatomic distance between the epilayer and the substrate matching with the theoretically predicted value. The first atomic layer of the grown film on graphene is vertically aligned with the top layer of the substrate with these atoms having different polarities, substantiating the remote interaction of adatoms with the substrate through graphene. These results directly show the impact of interface properties formed by different graphene transfer methods on remote epitaxy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Revealing the vacuum level in an infinite solid by real-space potential unfolding

Although real materials are finite in size, electronic structure theory is built on the assumption of infinitely large solids, which led to a longstanding controversy: where is the vacuum level? Furthermore, we introduce an analytic real-space potential-unfolding approach to uncover the vacuum level in infinitely large solids. First-principles calculations show that, in the absence of a physical surface, the bulk band structure, often measured with respect to an average bulk potential, is offset by a hereto unknown and orientation-dependent bulk quadrupole with respect to the vacuum level. By identifying intrinsic contributions of a bulk solid to its surface and interface properties, our theory eliminates the ambiguities surrounding the physical origin of the band alignment between matters.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Low-cost, high-efficiency III-V photovoltaics enabled by remote epitaxy through graphene (Final Technical Report)

One of the most important outcomes of this project was that the team developed a method to directly grow graphene layer in wafer-scale on III-V substrates. Conventionally, graphene had to be transferred for remote epitaxy, which has imposed significant challenges in scalability, film quality, and substrate recycling, due to the transfer-related issues. The newly developed method of directly forming 2D layers by Metal-Organic Chemical Vapor Deposition (MOCVD) has realized wafer-scale, defect-free graphene formation for remote epitaxy, which has huge implications not only for solar cells but also in expanding the scalability and the possibility for heterointegration with dissimilar material platforms. Another important outcome was on better understanding of remote epitaxy mechanism. The growth of III-V on graphene is vastly different from directly growing films on III-V substrates, because the surface energy of graphene is very small, meaning that the nucleation density on graphene will be much lower than exposed III-V surfaces. Also, the graphene and the interface properties critically affect remote interaction through graphene. With this obtained knowledge regarding III-V remote epitaxy, we were able to achieve wafer-scale single-crystalline remote epitaxy, 100% exfoliation of the remote epitaxial films, as well as multiple times of GaAs wafer reusability demonstration. The general rule of thumbs found during this project will be a stepping stone for the growth and fabrication of various high-performance devices by remote epitaxy. Lastly, because remote epitaxy and 2DLT offer a pathway to isolate single-crystal membranes from the host wafers, the wafer-scale remote epitaxy processes developed in this project could open up pathways for new functionality and multi-functionality by heterointegration of remote epitaxially formed membranes.

14 SOLAR ENERGY↗
DOE OSTI2023

Tomographic optical emission spectroscopy of atmospheric pressure plasma interacting with complex surfaces

Plasma distribution in 3D space is heavily influenced by complex surfaces and the coupling interactions between plasma properties and interfacing material properties. For example, guided streamers that transition to surface ionization waves (SIWs) and propagate over structured dielectrics experience field enhancements that can lead to localized increases in ionization rates and complex 3D configurations that are difficult to analyze. Investigating these configurations requires techniques than can provide a more complete 3D picture. To help address this capability gap, a tomographic optical emission spectroscopy (tomo-OES) diagnostic system has been developed at Sandia National Laboratories that can resolve SIWs. The system includes four intensified cameras that measure the angular projections of the plasma light emission through bandpass filters. A dot calibration target co-registers each angular projection to the same voxel grid and an algebraic reconstruction technique (ART) recovers the light intensity at each voxel. An atmospheric pressure plasma jet (APPJ), provided by Peter Bruggeman, has been investigated and representative results are shown in Figure 1. Here, a bandpass filter was used to isolate emission from the N 2 second positive system (SPS) at 337.1 nm to capture the transition of the streamer to SIW on a planar dielectric surface (relative permittivity 3.3) located 3 mm below the APPJ [3]. The surface wave velocity was 3.5x10 4 (m/s), consistent with measurements made by Steven Shannon. Characterization of this APPJ will support the group effort of standing up a reproducible APPJ across institutions for applications such as liquid treatment, catalysis, and plasma aided combustion. Future work will investigate non-planar surfaces and eventually develop tomographic laser-induced fluorescence (tomo-LIF) approaches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗