SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Design procedure developed for dc-to-dc power converters with multiple outputs having inductors wound on common core. With common core, minimum load current consistent with good output regulation is lower, output regulation is improved, and total inductor size and weight is reduced.
Characteristics of the boat inductor for keeping liquid metal in the suspended state are examined. Behavioral features of the liquid metal, and the suspension boundary of liquid metal in the lower position are discussed. It is concluded that the inductor can be used to crystallize metals in the suspended state.
Optimal parameters obtained designing near saturation point. New iterative procedure aids design of dc inductors with airgaps in cores. For given core area and length, technique gives design having specified inductance and peak flux density in core, using minimum required copper weight. Executed rapidly on programmable, hand-held calculator. Applications include lightweight inductors for aircraft electronics.
Procedures for ferrite-core and Molypermalloy-core inductors detailed. Report presents design procedures for two types of highfrequency inductors: those with iron or ferrite cores and lumped airgaps and those with Molypermally powder cores and distributed airgaps.
The common mode inductor is the corner stone of filter design. One of the most important parameters of performance is leakage inductance. The role of leakage inductance in filter performance and current handling is discussed. It is demonstrated that leakage inductance is, in fact, desirable. Underlying physics of operation for the common mode inductor is reviewed. A model is presented which enables the designer to predict the leakage inductance of the common mode choke.
The L-C resonant decay technique for measuring circuit Q or losses is improved by eliminating the switch from the inductor-capacitor loop. A MOSFET switch is used instead to momentarily connect the resonant circuit to an existing voltage source, which itself is gated off during the decay transient. Very reproducible, low duty cycle data could be taken this way over a dynamic voltage range of at least 10:1. Circuit Q is computed from a polynomial fit to the sequence of the decaying voltage maxima. This method was applied to measure the losses at 60 kHz in inductors having loose powder cores of moly permalloy and an Mn-Zn power ferrite. After the copper and capacitor losses are separated out, the resulting specific core loss is shown to be roughly as expected for the MPP powder, but anomalously high for the ferrite powder. Possible causes are mentioned.
Gyrator type circuit which requires only three amplifiers and which, when terminated with capacitor, can replace ungrounded inductor
As the power density of electric machines and power electronics continues to increase to meet the demands of more electric aircraft, the thermal management of these devices becomes increasingly important. Ideally, the thermal management solution of the device should have high thermal conductivity and be electrically insulating so that it can be directly integrated with the device in question. Technical ceramics are a class of materials that meet these two requirements. Direct liquid cooling by submerging electric components in a dielectric fluid is an alternate option, but adds system complexity and may incur pumping loss. In this work, the thermal management solution for a high frequency inductor is presented. A conventional wicked heat pipe is designed that is made from a solid ceramic case with a sintered ceramic wick. This heat pipe can provide structural support for the core and windings and is electrically insulating, so it does not incur any additional eddy current losses from the high frequency magnetic fields. It does not require additional pumping power, because conventional wicked heat pipes are passive devices. In this paper, the manufacturing process of the ceramic heat pipe is also presented. It is shown that the sintering of large diameter spherical ceramic particles is difficult due to their high specific surface area and low surface free energy. To overcome this difficulty, a flux material was used to initiate liquid phase sintering. The results of the sintering trials show that for the 120 μm diameter α-Al2O3powder selected for the wick, the combination of 1650°C sintering temperature and the addition of 5 wt% talc sintered the porous matrix together sufficiently for use as a heat pipe wic
As the power density of electric machines and power electronics continues to increase to meet the demands of more electric aircraft, the thermal management of these devices becomes increasingly important. Ideally, the thermal management solution of the device should have high thermal conductivity and be electrically insulating so that it can be directly integrated with the device in question. Technical ceramics are a class of materials that meet these two requirements. Direct liquid cooling by submerging electric components in a dielectric fluid is an alternate option, but adds system complexity and may incur pumping loss. In this work, the thermal management solution for a high frequency inductor is presented. A conventional wicked heat pipe is designed that is made from a solid ceramic case with a sintered ceramic wick. This heat pipe can provide structural support for the core and windings and is electrically insulating, so it does not incur any additional eddy current losses from the high frequency magnetic fields. It does not require additional pumping power, because conventional wicked heat pipes are passive devices. In this paper, the manufacturing process of the ceramic heat pipe is also presented. It is shown that the sintering of large diameter spherical ceramic particles is difficult due to their high specific surface area and low surface free energy. To overcome this difficulty, a flux material was used to initiate liquid phase sintering. The results of the sintering trials show that for the 120 μm diameter α-Al2O3 powder selected for the wick, the combination of 1650°C sintering temperature and the addition of 5 wt% talc sintered the porous matrix together sufficiently for use as a heat pipe wick.
Voltage regulator alternately connects an inductor in parallel and in series with the input voltage source. This flyback voltage regulator provides a regulated dc voltage to varying loads from a varying dc supply and gives fast response to load and supply changes.
Encapsulated RF inductor with an insulated coil has a high Q and remains stable for long periods of time at high temperatures. The coil is wound on a core and both are encapsulated in an epoxy resin. Two terminals are soldered to the coil.
Gyrator circuits using only transistors, capacitors, and resistors which can replace both grounded and ungrounded inductors have been developed to permit complete microminiaturization of circuitry by integration of the components.
Ponderomotive forces acting upon conductive bodies in traveling magnetic field of cylindrical inductor, and effect on magnetohydrodynamic generator design
Performance test of homopolar inductor alternator for Brayton cycle space power system
Analysis and design of inductors for protecting power transistors against current surges in inverter bridge circuits
Digital computer program for homopolar inductor alternator electromagnetic design analysis
Motor starting characteristics of two inductor alternators