Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Two- and three-dimensional viscous computations of a hypersonic inlet flow

The three-dimensional parabolized Navier-Stokes code has been used to investigate the flow through a Mach 7.4 inlet. A two-dimensional parametric study of grid resolution, turbulence modeling and effect of gamma has been done and compared with experimental results. The results show that mesh resolution of the shock waves, real gas effects and turbulence length scaling are very important to get accurate results for hypersonic inlet flows. In addition a three-dimensional calculation of the Mach 7.4 inlet has been done on a straight sideplate configuration. The results show that the glancing shock/boundary layer interaction phenomena causes significant three-dimensional flow in the inlet.

Kunik, William G.↗
NASA NTRS1974

Low-speed wind-tunnel investigation of the aerodynamic and acoustic performance of a translating grid choked flow inlet

The aerodynamic and acoustic performance of a translating grid choked-flow inlet was determined in a low-speed wind tunnel at free-stream velocities of 24, 32, and 45 m/sec and incidence angles of 0, 10, 20, 30, 35, 40, 45, and 50 deg. The inlet was sized to fit a 13.97- centimeter-diameter fan with a design weight flow of 2.49 kg/sec. Measurements were made to determine inlet total pressure recovery, flow distortion, and sound pressure level for both choked and unchoked geometries over a range of inlet weight flows. For the unchoked geometry, inlet total pressure recovery ranged from 0.983 to 0.989 at incidence angles less than 40 deg. At 40 deg incidence angle, inlet cowl separation was encountered which resulted in lower values of pressure recovery and higher levels of fan broadband noise. For the choked geometry, increasing total pressure losses occurred with increasing inlet weight flow that prevented the inlet from reaching full choked conditions with the particular fan used. These losses were attributed to the high Mach number drag rise characteristics of airfoil grid. At maximum attainable inlet weight flow, the total pressure recovery at static conditions was 0.935. The fan blade passing frequency and other fan generated pure tones were eliminated from the noise spectrum, but the broadband level was increased.

Abbott, J. M.↗
NASA NTRS1972

Aerodynamic and Acoustic Performance of Two Choked-Flow Inlets Under Static Conditions

Tests were conducted to determine the aerodynamic and acoustic performance of two choking flow inlets under static conditions. One inlet choked the flow in the cowl throat by an axial translation of the inlet centerbody. The other inlet employed a translating grid of airfoils to choke the flow. Both inlets were sized to fit a 13.97 cm diameter fan with a design weight flow of 2.49 kg/sec. The inlets were operated in both the choked and unchoked modes over a range of weight flows. Measurements were made of inlet pressure recovery, flow distortion, surface static pressure distribution, and fan noise suppression. Choking of the translating centerbody inlet reduced blade passing frequency noise by 29 db while yielding a total pressure recovery of 0.985. Noise reductions were also measured at 1/3-octave band center frequencies of 2500, 5000, and 20,000 cycles. The translating grid inlet gave a total pressure recovery of 0.968 when operating close to the choking weight flow. However, an intermittent high intensity noise source was encountered with this inlet that precluded an accurate measurement of inlet noise suppression.

Miller, B. A.↗
NASA NTRS1993

Several examples where turbulence models fail in inlet flow field analysis

Computational uncertainties in turbulence modeling for three dimensional inlet flow fields include flows approaching separation, strength of secondary flow field, three dimensional flow predictions of vortex liftoff, and influence of vortex-boundary layer interactions; computational uncertainties in vortex generator modeling include representation of generator vorticity field and the relationship between generator and vorticity field. The objectives of the inlet flow field studies presented in this document are to advance the understanding, prediction, and control of intake distortion and to study the basic interactions that influence this design problem.

Anderson, Bernhard H.↗
NASA NTRS1992

The effects of inlet flow modification on cavitating inducer performance

This paper explores the effect of inlet flow modification on the cavitating and noncavitating performance of two cavitating inducers, one of simple helical design and the other a model of the low-pressure LOX pump in the Space Shuttle Main Engine. The modifications were generated by sections of honeycomb, both uniform and nonuniform. Significant improvement in the performance over a wide range of flow coefficients resulted from the use of either honeycomb section. Measurements of the axial and swirl velocity profiles of the flows entering the inducers were made in order to try to understand the nature of the inlet flow and the manner in which it is modified by the honeycomb sections.

Del Valle, J.↗
NASA NTRS1992

Coupled numerical simulation of the external and engine inlet flows for the F-18 at large incidence

This paper presents a numerical simulation of the external and engine inlet flows for the F-18 aircraft at typical high-angle-of-attack flight conditions. Two engine inlet mass flow rates, corresponding to flight idle and maximum power, were computed. This was accomplished using a structured, overset grid technique to couple the external and internal grid systems. Reynolds-averaged Navier-Stokes solutions were obtained using an implicit, finite-differencing scheme. Results show a strong coupling of the external and engine inlet flows, especially at the maximum power setting. Increasing the mass flow rate through the inlet caused the primary vortex breakdown location to move downstream. This trend is also observed in flight tests performed on the F-18. A reversed flow region upstream of the inlet duct is visible in the faired-inlet and flight-idle computations. This flow reversal is not present in the maximum power setting computation. These large-scale changes in flow structure highlight the importance of simulating inlet conditions in high-angle-of-attack aircraft computations.

Murman, Scott M.↗
NASA NTRS1986

Numerical simulation of scramjet inlet flow fields

A computer program was developed to analyze supersonic combustion ramjet (scramjet) inlet flow fields. The program solves the three-dimensional Euler or Reynolds averaged Navier-Stokes equations in full conservation form by either the fully explicit or explicit-implicit, predictor-corrector method of MacCormack. Turbulence is modeled by an algebraic eddy-viscosity model. The analysis allows inclusion of end effects which can significantly affect the inlet flow field. Detailed laminar and turbulent flow results are presented for a symmetric-wedge corner, and comparisons are made with the available experimental results to allow assessment of the program. Results are then presented for two inlet configurations for which experimental results exist at the NASA Langley Research Center.

Kumar, Ajay↗
NASA NTRS1974

Two-stage fan. 2: Data and performance with redesigned second stage rotor uniform and distorted inlet flows

A two-stage fan with a first rotor tip speed of 1450 ft/sec (441.96 m/sec) and no inlet guide vanes was tested with uniform and distorted inlet flows, with a redesigned second rotor having a part span shroud to prevent flutter, with variable-stagger stators set in nominal positions, and without rotor casing treatment. The fan achieved a pressure ratio 2.8 at a corrected flow of 185.4 lbm/sec (84.0 kg/sec), an adiabatic efficiency of 85.0 percent, and a stall margin of 12 percent. The redesigned second rotor did not flutter. Tip radial distortion reduced the stall margin at intermediate speed, but had little effect on stall margin at high or low speeds. Hub radial distortion reduced the stall margin at design speed but increased stall margin at low speed. Circumferential distortion reduced stall pressure ratio and flow to give approximately the same stall lines with uniform inlet flow. Distortions were attenuated by the fan. For Vol. 1, see N74-11421.

Messenger, H. E.↗
NASA NTRS1978

Reduction of fan noise in an anechoic chamber by reducing chamber wall induced inlet flow disturbances

The difference between the flight and ground static noise of turbofan engines presents a significant problem in engine noise testing. The additional noise for static testing has been attributed to inlet flow disturbances or turbulence interacting with the fan rotor. In an attempt to determine a possible source of inflow disturbances entering fans tested in the Lewis Research Center anechoic chamber, the inflow field was studied using potential flow analysis. These potential flow calculations indicated that there was substantial flow over the wall directly behind the fan inlet that could produce significant inflow disturbances. Fan noise tests were run with various extensions added to the fan inlet to move the inlet away from this backwall and thereby reduce the inlet flow disturbances. Significant noise reductions were observed with increased inlet length. Over 5 db reduction of the blade passage tone sound power level was observed between the shortest and longest inlets at 90% fan speed and the first overtone was reduced 9 db. High frequency broadband noise was also reduced.

Dittmar, J. H.↗
NASA NTRS1978

Reduction of fan noise in an anechoic chamber by reducing chamber wall induced inlet flow disturbances

The difference between the flight and ground static noise of turbofan engines has been identified as a significant problem in engine noise testing. The additional noise for static testing has been attributed to inlet flow disturbances or turbulence interacting with the fan rotor. In an attempt to determine a possible source of inflow disturbances entering fans tested in the Lewis Research Center anechoic chamber the inflow field was studied using potential flow analysis. These potential flow calculations indicated that there was substantial flow over the wall directly behind the fan inlet that could produce significant inflow disturbances. Fan noise tests were run with various extensions added to the fan inlet to move the inlet away from this backwall and thereby reduce the inlet flow disturbances. Significant noise reductions were observed with increased inlet length. Over 5 dB reduction of the blade passage tone sound power level was observed between the shortest and longest inlets at 90% fan speed and the first overtone was reduced 9 dB. High frequency broadband noise was also reduced.

Dittmar, J. H.↗
NASA NTRS1995

Evaluation of F/A-18A HARV inlet flow analysis with flight data

The F/A-18A aircraft has experienced engine stalls at high angles-of-attack and yaw flight conditions which were outside of its flight envelope. Future aircraft may be designed to operate routinely in this flight regime. Therefore, it is essential that an understanding of the inlet flow field at these flight conditions be obtained. Due to the complex interactions of the fuselage and inlet flow fields, a study of the flow within the inlet must also include external effects. Full Navier-Stokes (FNS) calculations on the F/A-18A High Alpha Research Vehicle (HARV) inlet for several angles-of-attack with sideslip and free stream Mach numbers have been obtained. The predicted forebody/fuselage surface static pressures agreed well with flight data. The surface static pressures along the inlet lip are in good agreement with the numerical predictions. The major departure in agreement is along the bottom of the lip at 30 deg and 60 deg angle-of-attack where a possible streamwise flow separation is not being predicted by the code. The circumferential pressure distributions at the engine face are in very good agreement with the numerical results. The variation in surface static pressure in the circumferential direction is very small with the exception of 60 angle-of-attack. Although the simulation does not include the effect of the engine, it appears that this omission has a second order effect on the circumferential pressure distribution. An examination of the unsteady flight test data base has shown that the secondary vortex migrates a significant distance with time. In fact, the extent of this migration increases with angle-of-attack with increasing levels of distortion. The effects of the engine on this vortex movement is unknown. This implies that the level of flow unsteadiness increases with increasing distortion. Since the computational results represent an asymptotic solution driven by steady boundary conditions, these numerical results may represent an arbitrary point in time. A comparison of the predicted total pressure contours with flight data indicates that the numerical results are within the excursion range of the unsteady data which is the best the calculations can attain unless an unsteady simulation is performed.

Smith, C. Frederic↗
NASA NTRS1974

Combined Quadrupole-dipole Model for Inlet Flow Distortion Noise from a Subsonic Fan

A combined quadrupole-dipole model has been developed for the noise generated by inlet flow distortion in a subsonic fan. A formula is derived for the total upstream-radiated acoustic power in each tone as a function of the design parameters of the fan and the properties of the inlet flow distortion. Numerical results are obtained for values of the parameters corresponding to various quiet fans. The analysis is compared with noise measurements taken on a 51-cm (20-in.) diameter research fan as well as with those taken on a number of full-scale fan stages. Fairly good agreement was obtained. It should therefore be possible to use this model to study the noise-reduction potential of the various fan design parameters.

Goldstein, M. E.↗
NASA NTRS1986

Study of hypersonic inlet flow fields with a three-dimensional Navier-Stokes code

A three-dimensional Navier-Stokes code is used to study the flow through an inlet with a rectangular capture area, but with circular or essentially circular internal cross-sections. The inlet may have a center body extending partially or fully over the length of the inlet. Calculations are made under a variety of geometrical constraints imposed on the inlet cross-sections to study the flow quality in the inlet. It is observed that for this class of inlets, the boundary layer has a tendency to thicken and separate readily due to the adverse pressure gradient caused by the continuous compression in the inlet. Since no experimental results are yet available, this paper has presented only the numerical results from the present analysis.

Kumar, A.↗
NASA NTRS1980

Calculation of inlet flow fields by an implicit technique

Two-dimensional inlet flow fields in a supersonic free stream are calculated by an implicit, shock-capturing, finite-difference method. The Euler equations are subjected to a general curvilinear transformation and a body-fitted coordinate system is employed. The method is used to solve supercritical, critical, and subcritical flow fields which are simulated by prescribing appropriate conditions at the inlet outflow boundary. Results are presented for a drooped-cowl inlet.

Biringen, S.↗