Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “I-V”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1971

Research, Development and Fabrication of Lithium Solar Cells

This report continues studies on cells made with low temperature (<400degC) single-cycle, lithium diffusion schedules. Measurements of concentration of lithium at the back surface showed that C(sub S) changes with time consisting of a build-up to a maximum value (above 10(exp 17) cm(exp -3)) with gradual decrease at longer diffusion times. Using the estimated C(sub S) values, theoretical lithium profiles were calculated. The calculated concentration near the PN junction was higher than those measured by the capacitance voltage (C-V) technique. The calculated concentration gradients were one-seventh of those measured by C-V methods. Both the concentration and its gradient were proportional to C(sub S). Estimates of C(sub S) obtained by extrapolating from C-V measured values of concentration and gradient near the PN junction, showed a decrease in C(sub S) for longer diffusion times. This fact supported the trend observed in Shipment C-13, where,, at longer times, the spread in values of V(sub oc), lithium concentration, and gradient became greater. The general conclusion was that the I-V characteristics were well controlled, with good cell output, but for longer diffusion times the lithium concentration gradient could have wider spread. The work described has led to greater insight into the lithium distribution dependence on the surface conditions. The surface conditions could be changed by varying the method used to apply lithium. Vacuum evaporation of lithium shows promise, and another exhaustive test of this method is in progress. Shipment C-13 is summarized, and the succeeding lots (C-14, C-15) are described. It is felt that improved monitoring of cell properties is at hand, and that the control of cell fabrication processes has advanced to where the effects of subtle differences in lithium distribution can now be seen. Evaluation is continuing on the best method to scale up the fabrication steps. A different sequence of fabrication is planned for Shipments C-14 and C-15.

Iles, Peter A.↗
NASA NTRS1972

Proximity effect between superconductivity and normal metals

The SNS junctions were limited to having gold (n) layers of less than 3000 A in order to avoid having the tin (S) films become normal under the influence of the signal current in the gold. The gold layer was alloyed with 10 wt% copper to shorten its electronic mean free path, increasing the tin layer critical current while decreasing the Josephson critical current. It was also found that a previously reported anomalous voltage shift in the presence of I2 is caused by the tin being driven normal. After deposition, the samples were transferred to a conventional cryostat to provide better thermal contact to the films. This reduction of heating in the films produced more linear I-V characteristics and a change in the constant voltage current gain. In order to achieve power gain the SNS device must be operated at lower temperatures were the effects of fluctuations are less and be constructed such that the input resistance is much reduced and the dynamic output resistance increased. A geometry is proposed using a more sophisticated evaporator.

Meissner, H.↗
NASA NTRS1972

A study of the electrical properties of p-n junctions formed by ion-implantation into gallium arsenide

In the process of ion implantation, ion beams bombard the surface and create undesirable surface effects. The surface effects were investigated, and surface leakage currents were shown to be reduced by surface treatment. I-V characteristics and C-V measurements were obtained for the Zn-GaAs and Zn-(In,Ga)As junction is considered as a p-i-n heterojunction, without generation-recombination current. The Zn-GaAs junction is considered as a p-n homojunction with appreciable generation-recombination currents.

Lin, A. H.↗
NASA NTRS1973

Effects of proton irradiation and temperature on 1 ohm-cm and 10 ohm-cm silicon solar cells

The 1 ohm-cm and 10 ohm-cm silicon solar cells were exposed to 1.0 MeV protons at a fixed flux of 10 to the 9th power P/sq cm-sec and fluences of 10 to the 10th power, 10 to the 11th power, 10 to the 12th power and 3 X 10 to the 12th power P/sq cm. I-V curves of the cells were made at room temperature, 65 C and 165 C after each irradiation. A value of 139.5 mw/sq cm was taken as AMO incident energy rate per unit area. Degradation occurred for both uncovered 1 ohm-cm and 10 ohm-cm cells. Efficiencies are generally higher than those of comparable U.S. cells tested earlier. Damage (loss in maximum power efficiency) with proton fluence is somewhat higher for 10 ohm-cm cells, measured at the three temperatures, for fluences above 2 X 10 to the 11th power P/sq cm. Cell efficiency, as expected, changes drastically with temperature.

Nicoletta, C. A.↗
NASA NTRS1973

Solar array synthesis computer program

Photovoltaic characteristics have been measured on solar cells irradiated by 1 MeV electrons to fluences ranging from 1 x 10 to the 13th power e/sq cm to 1 x 10 to the 16th power e/sq cm, for cell temperatures ranging from 123 K to 473 K and for illumination intensities ranging from 5m W/sq cm to 1830m W/sq cm. Empirical equations have been derived from these measurements to describe the behavior of light generated current, open circuit voltage and I-V curve shape over various portions of these temperature/illumination ranges. Both 10 ohms/cm and 17 ohms/cm n-p silicon solar cells were tested, and similar analytical expressions were formulated for easy comparison between the two resistivities.

Faith, T. J.↗
NASA NTRS1973

Design of nonlinear resistive networks with prescribed input-output behavior.

This paper considers the problem of designing nonlinear multiport resistive networks for prescribed driving point and transfer characteristics. It is shown that, if the topology of the desired network is given, then the i-v characteristics of the nonlinear elements can be obtained iteratively. This is achieved by implementation of a newly developed steepest descent criterion.

Peikari, B.↗
NASA NTRS1974

Methods of improving the efficiency of photovoltaic cells

Work on aluminum-alloyed silicon grating cells is continued. Optimization of the geometry (grating line width and spacing) confirms the analysis of such cells. A 1 sq cm grating cell was fabricated and its i-V characteristic was measured under an AMO solar simulator. It is found that the efficiency of this cell would be about 7.9%, if it were covered by the usual antireflection coating. The surface of the cell is not covered by a diffused junction. The response is blue shifted; the current is somewhat higher than that produced by a commercial Si cell. However, the open circuit voltage is low, and attempts to optimize the open circuit voltage of the aluminum-alloy junctions are described. A preliminary X-ray topographic examination of GaAs specimens of the type commonly used to make solar cells is studied. The X-ray study shows that the wafers are filled with regions having strain gradients, possibly caused by precipitates. It is possible that a correlation exists between the presence of low mechanical perfection and minority carrier diffusion lengths of GaAs crystals.

Loferski, J. J.↗